1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * arch/arm/mach-lpc32xx/pm.c
4 *
5 * Original authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
6 * Modified by Kevin Wells <kevin.wells@nxp.com>
7 *
8 * 2005 (c) MontaVista Software, Inc.
9 */
10
11 /*
12 * LPC32XX CPU and system power management
13 *
14 * The LPC32XX has three CPU modes for controlling system power: run,
15 * direct-run, and halt modes. When switching between halt and run modes,
16 * the CPU transistions through direct-run mode. For Linux, direct-run
17 * mode is not used in normal operation. Halt mode is used when the
18 * system is fully suspended.
19 *
20 * Run mode:
21 * The ARM CPU clock (HCLK_PLL), HCLK bus clock, and PCLK bus clocks are
22 * derived from the HCLK PLL. The HCLK and PCLK bus rates are divided from
23 * the HCLK_PLL rate. Linux runs in this mode.
24 *
25 * Direct-run mode:
26 * The ARM CPU clock, HCLK bus clock, and PCLK bus clocks are driven from
27 * SYSCLK. SYSCLK is usually around 13MHz, but may vary based on SYSCLK
28 * source or the frequency of the main oscillator. In this mode, the
29 * HCLK_PLL can be safely enabled, changed, or disabled.
30 *
31 * Halt mode:
32 * SYSCLK is gated off and the CPU and system clocks are halted.
33 * Peripherals based on the 32KHz oscillator clock (ie, RTC, touch,
34 * key scanner, etc.) still operate if enabled. In this state, an enabled
35 * system event (ie, GPIO state change, RTC match, key press, etc.) will
36 * wake the system up back into direct-run mode.
37 *
38 * DRAM refresh
39 * DRAM clocking and refresh are slightly different for systems with DDR
40 * DRAM or regular SDRAM devices. If SDRAM is used in the system, the
41 * SDRAM will still be accessible in direct-run mode. In DDR based systems,
42 * a transition to direct-run mode will stop all DDR accesses (no clocks).
43 * Because of this, the code to switch power modes and the code to enter
44 * and exit DRAM self-refresh modes must not be executed in DRAM. A small
45 * section of IRAM is used instead for this.
46 *
47 * Suspend is handled with the following logic:
48 * Backup a small area of IRAM used for the suspend code
49 * Copy suspend code to IRAM
50 * Transfer control to code in IRAM
51 * Places DRAMs in self-refresh mode
52 * Enter direct-run mode
53 * Save state of HCLK_PLL PLL
54 * Disable HCLK_PLL PLL
55 * Enter halt mode - CPU and buses will stop
56 * System enters direct-run mode when an enabled event occurs
57 * HCLK PLL state is restored
58 * Run mode is entered
59 * DRAMS are placed back into normal mode
60 * Code execution returns from IRAM
61 * IRAM code are used for suspend is restored
62 * Suspend mode is exited
63 */
64
65 #include <linux/suspend.h>
66 #include <linux/io.h>
67 #include <linux/slab.h>
68
69 #include <asm/cacheflush.h>
70
71 #include "lpc32xx.h"
72 #include "common.h"
73
74 #define TEMP_IRAM_AREA IO_ADDRESS(LPC32XX_IRAM_BASE)
75
76 /*
77 * Both STANDBY and MEM suspend states are handled the same with no
78 * loss of CPU or memory state
79 */
lpc32xx_pm_enter(suspend_state_t state)80 static int lpc32xx_pm_enter(suspend_state_t state)
81 {
82 int (*lpc32xx_suspend_ptr) (void);
83 void *iram_swap_area;
84
85 /* Allocate some space for temporary IRAM storage */
86 iram_swap_area = kmemdup((void *)TEMP_IRAM_AREA,
87 lpc32xx_sys_suspend_sz, GFP_KERNEL);
88 if (!iram_swap_area)
89 return -ENOMEM;
90
91 /*
92 * Copy code to suspend system into IRAM. The suspend code
93 * needs to run from IRAM as DRAM may no longer be available
94 * when the PLL is stopped.
95 */
96 memcpy((void *) TEMP_IRAM_AREA, &lpc32xx_sys_suspend,
97 lpc32xx_sys_suspend_sz);
98 flush_icache_range((unsigned long)TEMP_IRAM_AREA,
99 (unsigned long)(TEMP_IRAM_AREA) + lpc32xx_sys_suspend_sz);
100
101 /* Transfer to suspend code in IRAM */
102 lpc32xx_suspend_ptr = (void *) TEMP_IRAM_AREA;
103 flush_cache_all();
104 (void) lpc32xx_suspend_ptr();
105
106 /* Restore original IRAM contents */
107 memcpy((void *) TEMP_IRAM_AREA, iram_swap_area,
108 lpc32xx_sys_suspend_sz);
109
110 kfree(iram_swap_area);
111
112 return 0;
113 }
114
115 static const struct platform_suspend_ops lpc32xx_pm_ops = {
116 .valid = suspend_valid_only_mem,
117 .enter = lpc32xx_pm_enter,
118 };
119
120 #define EMC_DYN_MEM_CTRL_OFS 0x20
121 #define EMC_SRMMC (1 << 3)
122 #define EMC_CTRL_REG io_p2v(LPC32XX_EMC_BASE + EMC_DYN_MEM_CTRL_OFS)
lpc32xx_pm_init(void)123 static int __init lpc32xx_pm_init(void)
124 {
125 /*
126 * Setup SDRAM self-refresh clock to automatically disable o
127 * start of self-refresh. This only needs to be done once.
128 */
129 __raw_writel(__raw_readl(EMC_CTRL_REG) | EMC_SRMMC, EMC_CTRL_REG);
130
131 suspend_set_ops(&lpc32xx_pm_ops);
132
133 return 0;
134 }
135 arch_initcall(lpc32xx_pm_init);
136