1# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/i2c/i2c-arb-gpio-challenge.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: GPIO-based I2C Arbitration Using a Challenge & Response Mechanism
8
9maintainers:
10  - Doug Anderson <dianders@chromium.org>
11  - Peter Rosin <peda@axentia.se>
12
13description: |
14  This uses GPIO lines and a challenge & response mechanism to arbitrate who is
15  the master of an I2C bus in a multimaster situation.
16
17  In many cases using GPIOs to arbitrate is not needed and a design can use the
18  standard I2C multi-master rules.  Using GPIOs is generally useful in the case
19  where there is a device on the bus that has errata and/or bugs that makes
20  standard multimaster mode not feasible.
21
22  Note that this scheme works well enough but has some downsides:
23   * It is nonstandard (not using standard I2C multimaster)
24   * Having two masters on a bus in general makes it relatively hard to debug
25     problems (hard to tell if i2c issues were caused by one master, another,
26     or some device on the bus).
27
28  Algorithm:
29  All masters on the bus have a 'bus claim' line which is an output that the
30  others can see. These are all active low with pull-ups enabled.  We'll
31  describe these lines as:
32   * OUR_CLAIM: output from us signaling to other hosts that we want the bus
33   * THEIR_CLAIMS: output from others signaling that they want the bus
34
35  The basic algorithm is to assert your line when you want the bus, then make
36  sure that the other side doesn't want it also.  A detailed explanation is
37  best done with an example.
38
39  Let's say we want to claim the bus.  We:
40  1. Assert OUR_CLAIM.
41  2. Waits a little bit for the other sides to notice (slew time, say 10
42     microseconds).
43  3. Check THEIR_CLAIMS.  If none are asserted then the we have the bus and we
44     are done.
45  4. Otherwise, wait for a few milliseconds and see if THEIR_CLAIMS are released.
46  5. If not, back off, release the claim and wait for a few more milliseconds.
47  6. Go back to 1 (until retry time has expired).
48
49properties:
50  compatible:
51    const: i2c-arb-gpio-challenge
52
53  i2c-parent:
54    $ref: /schemas/types.yaml#/definitions/phandle
55    description:
56      The I2C bus that this multiplexer's master-side port is connected to.
57
58  our-claim-gpios:
59    maxItems: 1
60    description:
61      The GPIO that we use to claim the bus.
62
63  slew-delay-us:
64    default: 10
65    description:
66      Time to wait for a GPIO to go high.
67
68  their-claim-gpios:
69    minItems: 1
70    maxItems: 8
71    description:
72      The GPIOs that the other sides use to claim the bus.  Note that some
73      implementations may only support a single other master.
74
75  wait-free-us:
76    default: 50000
77    description:
78      We'll give up after this many microseconds.
79
80  wait-retry-us:
81    default: 3000
82    description:
83      We'll attempt another claim after this many microseconds.
84
85  i2c-arb:
86    type: object
87    $ref: /schemas/i2c/i2c-controller.yaml
88    unevaluatedProperties: false
89    description:
90      I2C arbitration bus node.
91
92required:
93  - compatible
94  - i2c-arb
95  - our-claim-gpios
96  - their-claim-gpios
97
98additionalProperties: false
99
100examples:
101  - |
102    #include <dt-bindings/gpio/gpio.h>
103    #include <dt-bindings/interrupt-controller/irq.h>
104
105    i2c-arbitrator {
106        compatible = "i2c-arb-gpio-challenge";
107        i2c-parent = <&i2c_4>;
108
109        our-claim-gpios = <&gpf0 3 GPIO_ACTIVE_LOW>;
110        their-claim-gpios = <&gpe0 4 GPIO_ACTIVE_LOW>;
111        slew-delay-us = <10>;
112        wait-retry-us = <3000>;
113        wait-free-us = <50000>;
114
115        i2c-arb {
116            #address-cells = <1>;
117            #size-cells = <0>;
118
119            sbs-battery@b {
120                compatible = "sbs,sbs-battery";
121                reg = <0xb>;
122                sbs,poll-retry-count = <1>;
123            };
124
125            embedded-controller@1e {
126                compatible = "google,cros-ec-i2c";
127                reg = <0x1e>;
128                interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
129                interrupt-parent = <&gpx1>;
130                pinctrl-names = "default";
131                pinctrl-0 = <&ec_irq>;
132                wakeup-source;
133            };
134        };
135    };
136