1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 **
4 ** PCI Lower Bus Adapter (LBA) manager
5 **
6 ** (c) Copyright 1999,2000 Grant Grundler
7 ** (c) Copyright 1999,2000 Hewlett-Packard Company
8 **
9 **
10 **
11 ** This module primarily provides access to PCI bus (config/IOport
12 ** spaces) on platforms with an SBA/LBA chipset. A/B/C/J/L/N-class
13 ** with 4 digit model numbers - eg C3000 (and A400...sigh).
14 **
15 ** LBA driver isn't as simple as the Dino driver because:
16 ** (a) this chip has substantial bug fixes between revisions
17 ** (Only one Dino bug has a software workaround :^( )
18 ** (b) has more options which we don't (yet) support (DMA hints, OLARD)
19 ** (c) IRQ support lives in the I/O SAPIC driver (not with PCI driver)
20 ** (d) play nicely with both PAT and "Legacy" PA-RISC firmware (PDC).
21 ** (dino only deals with "Legacy" PDC)
22 **
23 ** LBA driver passes the I/O SAPIC HPA to the I/O SAPIC driver.
24 ** (I/O SAPIC is integratd in the LBA chip).
25 **
26 ** FIXME: Add support to SBA and LBA drivers for DMA hint sets
27 ** FIXME: Add support for PCI card hot-plug (OLARD).
28 */
29
30 #include <linux/delay.h>
31 #include <linux/types.h>
32 #include <linux/kernel.h>
33 #include <linux/spinlock.h>
34 #include <linux/init.h> /* for __init */
35 #include <linux/pci.h>
36 #include <linux/ioport.h>
37 #include <linux/slab.h>
38
39 #include <asm/byteorder.h>
40 #include <asm/pdc.h>
41 #include <asm/pdcpat.h>
42 #include <asm/page.h>
43
44 #include <asm/ropes.h>
45 #include <asm/hardware.h> /* for register_parisc_driver() stuff */
46 #include <asm/parisc-device.h>
47 #include <asm/io.h> /* read/write stuff */
48
49 #include "iommu.h"
50
51 #undef DEBUG_LBA /* general stuff */
52 #undef DEBUG_LBA_PORT /* debug I/O Port access */
53 #undef DEBUG_LBA_CFG /* debug Config Space Access (ie PCI Bus walk) */
54 #undef DEBUG_LBA_PAT /* debug PCI Resource Mgt code - PDC PAT only */
55
56 #undef FBB_SUPPORT /* Fast Back-Back xfers - NOT READY YET */
57
58
59 #ifdef DEBUG_LBA
60 #define DBG(x...) printk(x)
61 #else
62 #define DBG(x...)
63 #endif
64
65 #ifdef DEBUG_LBA_PORT
66 #define DBG_PORT(x...) printk(x)
67 #else
68 #define DBG_PORT(x...)
69 #endif
70
71 #ifdef DEBUG_LBA_CFG
72 #define DBG_CFG(x...) printk(x)
73 #else
74 #define DBG_CFG(x...)
75 #endif
76
77 #ifdef DEBUG_LBA_PAT
78 #define DBG_PAT(x...) printk(x)
79 #else
80 #define DBG_PAT(x...)
81 #endif
82
83
84 /*
85 ** Config accessor functions only pass in the 8-bit bus number and not
86 ** the 8-bit "PCI Segment" number. Each LBA will be assigned a PCI bus
87 ** number based on what firmware wrote into the scratch register.
88 **
89 ** The "secondary" bus number is set to this before calling
90 ** pci_register_ops(). If any PPB's are present, the scan will
91 ** discover them and update the "secondary" and "subordinate"
92 ** fields in the pci_bus structure.
93 **
94 ** Changes in the configuration *may* result in a different
95 ** bus number for each LBA depending on what firmware does.
96 */
97
98 #define MODULE_NAME "LBA"
99
100 /* non-postable I/O port space, densely packed */
101 #define LBA_PORT_BASE (PCI_F_EXTEND | 0xfee00000UL)
102 static void __iomem *astro_iop_base __read_mostly;
103
104 static u32 lba_t32;
105
106 /* lba flags */
107 #define LBA_FLAG_SKIP_PROBE 0x10
108
109 #define LBA_SKIP_PROBE(d) ((d)->flags & LBA_FLAG_SKIP_PROBE)
110
LBA_DEV(struct pci_hba_data * hba)111 static inline struct lba_device *LBA_DEV(struct pci_hba_data *hba)
112 {
113 return container_of(hba, struct lba_device, hba);
114 }
115
116 /*
117 ** Only allow 8 subsidiary busses per LBA
118 ** Problem is the PCI bus numbering is globally shared.
119 */
120 #define LBA_MAX_NUM_BUSES 8
121
122 /************************************
123 * LBA register read and write support
124 *
125 * BE WARNED: register writes are posted.
126 * (ie follow writes which must reach HW with a read)
127 */
128 #define READ_U8(addr) __raw_readb(addr)
129 #define READ_U16(addr) __raw_readw(addr)
130 #define READ_U32(addr) __raw_readl(addr)
131 #define WRITE_U8(value, addr) __raw_writeb(value, addr)
132 #define WRITE_U16(value, addr) __raw_writew(value, addr)
133 #define WRITE_U32(value, addr) __raw_writel(value, addr)
134
135 #define READ_REG8(addr) readb(addr)
136 #define READ_REG16(addr) readw(addr)
137 #define READ_REG32(addr) readl(addr)
138 #define READ_REG64(addr) readq(addr)
139 #define WRITE_REG8(value, addr) writeb(value, addr)
140 #define WRITE_REG16(value, addr) writew(value, addr)
141 #define WRITE_REG32(value, addr) writel(value, addr)
142
143
144 #define LBA_CFG_TOK(bus,dfn) ((u32) ((bus)<<16 | (dfn)<<8))
145 #define LBA_CFG_BUS(tok) ((u8) ((tok)>>16))
146 #define LBA_CFG_DEV(tok) ((u8) ((tok)>>11) & 0x1f)
147 #define LBA_CFG_FUNC(tok) ((u8) ((tok)>>8 ) & 0x7)
148
149
150 /*
151 ** Extract LBA (Rope) number from HPA
152 ** REVISIT: 16 ropes for Stretch/Ike?
153 */
154 #define ROPES_PER_IOC 8
155 #define LBA_NUM(x) ((((unsigned long) x) >> 13) & (ROPES_PER_IOC-1))
156
157
158 static void
lba_dump_res(struct resource * r,int d)159 lba_dump_res(struct resource *r, int d)
160 {
161 int i;
162
163 if (NULL == r)
164 return;
165
166 printk(KERN_DEBUG "(%p)", r->parent);
167 for (i = d; i ; --i) printk(" ");
168 printk(KERN_DEBUG "%p [%lx,%lx]/%lx\n", r,
169 (long)r->start, (long)r->end, r->flags);
170 lba_dump_res(r->child, d+2);
171 lba_dump_res(r->sibling, d);
172 }
173
174
175 /*
176 ** LBA rev 2.0, 2.1, 2.2, and 3.0 bus walks require a complex
177 ** workaround for cfg cycles:
178 ** -- preserve LBA state
179 ** -- prevent any DMA from occurring
180 ** -- turn on smart mode
181 ** -- probe with config writes before doing config reads
182 ** -- check ERROR_STATUS
183 ** -- clear ERROR_STATUS
184 ** -- restore LBA state
185 **
186 ** The workaround is only used for device discovery.
187 */
188
lba_device_present(u8 bus,u8 dfn,struct lba_device * d)189 static int lba_device_present(u8 bus, u8 dfn, struct lba_device *d)
190 {
191 u8 first_bus = d->hba.hba_bus->busn_res.start;
192 u8 last_sub_bus = d->hba.hba_bus->busn_res.end;
193
194 if ((bus < first_bus) ||
195 (bus > last_sub_bus) ||
196 ((bus - first_bus) >= LBA_MAX_NUM_BUSES)) {
197 return 0;
198 }
199
200 return 1;
201 }
202
203
204
205 #define LBA_CFG_SETUP(d, tok) { \
206 /* Save contents of error config register. */ \
207 error_config = READ_REG32(d->hba.base_addr + LBA_ERROR_CONFIG); \
208 \
209 /* Save contents of status control register. */ \
210 status_control = READ_REG32(d->hba.base_addr + LBA_STAT_CTL); \
211 \
212 /* For LBA rev 2.0, 2.1, 2.2, and 3.0, we must disable DMA \
213 ** arbitration for full bus walks. \
214 */ \
215 /* Save contents of arb mask register. */ \
216 arb_mask = READ_REG32(d->hba.base_addr + LBA_ARB_MASK); \
217 \
218 /* \
219 * Turn off all device arbitration bits (i.e. everything \
220 * except arbitration enable bit). \
221 */ \
222 WRITE_REG32(0x1, d->hba.base_addr + LBA_ARB_MASK); \
223 \
224 /* \
225 * Set the smart mode bit so that master aborts don't cause \
226 * LBA to go into PCI fatal mode (required). \
227 */ \
228 WRITE_REG32(error_config | LBA_SMART_MODE, d->hba.base_addr + LBA_ERROR_CONFIG); \
229 }
230
231
232 #define LBA_CFG_PROBE(d, tok) { \
233 /* \
234 * Setup Vendor ID write and read back the address register \
235 * to make sure that LBA is the bus master. \
236 */ \
237 WRITE_REG32(tok | PCI_VENDOR_ID, (d)->hba.base_addr + LBA_PCI_CFG_ADDR);\
238 /* \
239 * Read address register to ensure that LBA is the bus master, \
240 * which implies that DMA traffic has stopped when DMA arb is off. \
241 */ \
242 lba_t32 = READ_REG32((d)->hba.base_addr + LBA_PCI_CFG_ADDR); \
243 /* \
244 * Generate a cfg write cycle (will have no affect on \
245 * Vendor ID register since read-only). \
246 */ \
247 WRITE_REG32(~0, (d)->hba.base_addr + LBA_PCI_CFG_DATA); \
248 /* \
249 * Make sure write has completed before proceeding further, \
250 * i.e. before setting clear enable. \
251 */ \
252 lba_t32 = READ_REG32((d)->hba.base_addr + LBA_PCI_CFG_ADDR); \
253 }
254
255
256 /*
257 * HPREVISIT:
258 * -- Can't tell if config cycle got the error.
259 *
260 * OV bit is broken until rev 4.0, so can't use OV bit and
261 * LBA_ERROR_LOG_ADDR to tell if error belongs to config cycle.
262 *
263 * As of rev 4.0, no longer need the error check.
264 *
265 * -- Even if we could tell, we still want to return -1
266 * for **ANY** error (not just master abort).
267 *
268 * -- Only clear non-fatal errors (we don't want to bring
269 * LBA out of pci-fatal mode).
270 *
271 * Actually, there is still a race in which
272 * we could be clearing a fatal error. We will
273 * live with this during our initial bus walk
274 * until rev 4.0 (no driver activity during
275 * initial bus walk). The initial bus walk
276 * has race conditions concerning the use of
277 * smart mode as well.
278 */
279
280 #define LBA_MASTER_ABORT_ERROR 0xc
281 #define LBA_FATAL_ERROR 0x10
282
283 #define LBA_CFG_MASTER_ABORT_CHECK(d, base, tok, error) { \
284 u32 error_status = 0; \
285 /* \
286 * Set clear enable (CE) bit. Unset by HW when new \
287 * errors are logged -- LBA HW ERS section 14.3.3). \
288 */ \
289 WRITE_REG32(status_control | CLEAR_ERRLOG_ENABLE, base + LBA_STAT_CTL); \
290 error_status = READ_REG32(base + LBA_ERROR_STATUS); \
291 if ((error_status & 0x1f) != 0) { \
292 /* \
293 * Fail the config read request. \
294 */ \
295 error = 1; \
296 if ((error_status & LBA_FATAL_ERROR) == 0) { \
297 /* \
298 * Clear error status (if fatal bit not set) by setting \
299 * clear error log bit (CL). \
300 */ \
301 WRITE_REG32(status_control | CLEAR_ERRLOG, base + LBA_STAT_CTL); \
302 } \
303 } \
304 }
305
306 #define LBA_CFG_TR4_ADDR_SETUP(d, addr) \
307 WRITE_REG32(((addr) & ~3), (d)->hba.base_addr + LBA_PCI_CFG_ADDR);
308
309 #define LBA_CFG_ADDR_SETUP(d, addr) { \
310 WRITE_REG32(((addr) & ~3), (d)->hba.base_addr + LBA_PCI_CFG_ADDR); \
311 /* \
312 * Read address register to ensure that LBA is the bus master, \
313 * which implies that DMA traffic has stopped when DMA arb is off. \
314 */ \
315 lba_t32 = READ_REG32((d)->hba.base_addr + LBA_PCI_CFG_ADDR); \
316 }
317
318
319 #define LBA_CFG_RESTORE(d, base) { \
320 /* \
321 * Restore status control register (turn off clear enable). \
322 */ \
323 WRITE_REG32(status_control, base + LBA_STAT_CTL); \
324 /* \
325 * Restore error config register (turn off smart mode). \
326 */ \
327 WRITE_REG32(error_config, base + LBA_ERROR_CONFIG); \
328 /* \
329 * Restore arb mask register (reenables DMA arbitration). \
330 */ \
331 WRITE_REG32(arb_mask, base + LBA_ARB_MASK); \
332 }
333
334
335
336 static unsigned int
lba_rd_cfg(struct lba_device * d,u32 tok,u8 reg,u32 size)337 lba_rd_cfg(struct lba_device *d, u32 tok, u8 reg, u32 size)
338 {
339 u32 data = ~0U;
340 int error = 0;
341 u32 arb_mask = 0; /* used by LBA_CFG_SETUP/RESTORE */
342 u32 error_config = 0; /* used by LBA_CFG_SETUP/RESTORE */
343 u32 status_control = 0; /* used by LBA_CFG_SETUP/RESTORE */
344
345 LBA_CFG_SETUP(d, tok);
346 LBA_CFG_PROBE(d, tok);
347 LBA_CFG_MASTER_ABORT_CHECK(d, d->hba.base_addr, tok, error);
348 if (!error) {
349 void __iomem *data_reg = d->hba.base_addr + LBA_PCI_CFG_DATA;
350
351 LBA_CFG_ADDR_SETUP(d, tok | reg);
352 switch (size) {
353 case 1: data = (u32) READ_REG8(data_reg + (reg & 3)); break;
354 case 2: data = (u32) READ_REG16(data_reg+ (reg & 2)); break;
355 case 4: data = READ_REG32(data_reg); break;
356 }
357 }
358 LBA_CFG_RESTORE(d, d->hba.base_addr);
359 return(data);
360 }
361
362
elroy_cfg_read(struct pci_bus * bus,unsigned int devfn,int pos,int size,u32 * data)363 static int elroy_cfg_read(struct pci_bus *bus, unsigned int devfn, int pos, int size, u32 *data)
364 {
365 struct lba_device *d = LBA_DEV(parisc_walk_tree(bus->bridge));
366 u32 local_bus = (bus->parent == NULL) ? 0 : bus->busn_res.start;
367 u32 tok = LBA_CFG_TOK(local_bus, devfn);
368 void __iomem *data_reg = d->hba.base_addr + LBA_PCI_CFG_DATA;
369
370 if ((pos > 255) || (devfn > 255))
371 return -EINVAL;
372
373 /* FIXME: B2K/C3600 workaround is always use old method... */
374 /* if (!LBA_SKIP_PROBE(d)) */ {
375 /* original - Generate config cycle on broken elroy
376 with risk we will miss PCI bus errors. */
377 *data = lba_rd_cfg(d, tok, pos, size);
378 DBG_CFG("%s(%x+%2x) -> 0x%x (a)\n", __func__, tok, pos, *data);
379 return 0;
380 }
381
382 if (LBA_SKIP_PROBE(d) && !lba_device_present(bus->busn_res.start, devfn, d)) {
383 DBG_CFG("%s(%x+%2x) -> -1 (b)\n", __func__, tok, pos);
384 /* either don't want to look or know device isn't present. */
385 *data = ~0U;
386 return(0);
387 }
388
389 /* Basic Algorithm
390 ** Should only get here on fully working LBA rev.
391 ** This is how simple the code should have been.
392 */
393 LBA_CFG_ADDR_SETUP(d, tok | pos);
394 switch(size) {
395 case 1: *data = READ_REG8 (data_reg + (pos & 3)); break;
396 case 2: *data = READ_REG16(data_reg + (pos & 2)); break;
397 case 4: *data = READ_REG32(data_reg); break;
398 }
399 DBG_CFG("%s(%x+%2x) -> 0x%x (c)\n", __func__, tok, pos, *data);
400 return 0;
401 }
402
403
404 static void
lba_wr_cfg(struct lba_device * d,u32 tok,u8 reg,u32 data,u32 size)405 lba_wr_cfg(struct lba_device *d, u32 tok, u8 reg, u32 data, u32 size)
406 {
407 int error = 0;
408 u32 arb_mask = 0;
409 u32 error_config = 0;
410 u32 status_control = 0;
411 void __iomem *data_reg = d->hba.base_addr + LBA_PCI_CFG_DATA;
412
413 LBA_CFG_SETUP(d, tok);
414 LBA_CFG_ADDR_SETUP(d, tok | reg);
415 switch (size) {
416 case 1: WRITE_REG8 (data, data_reg + (reg & 3)); break;
417 case 2: WRITE_REG16(data, data_reg + (reg & 2)); break;
418 case 4: WRITE_REG32(data, data_reg); break;
419 }
420 LBA_CFG_MASTER_ABORT_CHECK(d, d->hba.base_addr, tok, error);
421 LBA_CFG_RESTORE(d, d->hba.base_addr);
422 }
423
424
425 /*
426 * LBA 4.0 config write code implements non-postable semantics
427 * by doing a read of CONFIG ADDR after the write.
428 */
429
elroy_cfg_write(struct pci_bus * bus,unsigned int devfn,int pos,int size,u32 data)430 static int elroy_cfg_write(struct pci_bus *bus, unsigned int devfn, int pos, int size, u32 data)
431 {
432 struct lba_device *d = LBA_DEV(parisc_walk_tree(bus->bridge));
433 u32 local_bus = (bus->parent == NULL) ? 0 : bus->busn_res.start;
434 u32 tok = LBA_CFG_TOK(local_bus,devfn);
435
436 if ((pos > 255) || (devfn > 255))
437 return -EINVAL;
438
439 if (!LBA_SKIP_PROBE(d)) {
440 /* Original Workaround */
441 lba_wr_cfg(d, tok, pos, (u32) data, size);
442 DBG_CFG("%s(%x+%2x) = 0x%x (a)\n", __func__, tok, pos,data);
443 return 0;
444 }
445
446 if (LBA_SKIP_PROBE(d) && (!lba_device_present(bus->busn_res.start, devfn, d))) {
447 DBG_CFG("%s(%x+%2x) = 0x%x (b)\n", __func__, tok, pos,data);
448 return 1; /* New Workaround */
449 }
450
451 DBG_CFG("%s(%x+%2x) = 0x%x (c)\n", __func__, tok, pos, data);
452
453 /* Basic Algorithm */
454 LBA_CFG_ADDR_SETUP(d, tok | pos);
455 switch(size) {
456 case 1: WRITE_REG8 (data, d->hba.base_addr + LBA_PCI_CFG_DATA + (pos & 3));
457 break;
458 case 2: WRITE_REG16(data, d->hba.base_addr + LBA_PCI_CFG_DATA + (pos & 2));
459 break;
460 case 4: WRITE_REG32(data, d->hba.base_addr + LBA_PCI_CFG_DATA);
461 break;
462 }
463 /* flush posted write */
464 lba_t32 = READ_REG32(d->hba.base_addr + LBA_PCI_CFG_ADDR);
465 return 0;
466 }
467
468
469 static struct pci_ops elroy_cfg_ops = {
470 .read = elroy_cfg_read,
471 .write = elroy_cfg_write,
472 };
473
474 /*
475 * The mercury_cfg_ops are slightly misnamed; they're also used for Elroy
476 * TR4.0 as no additional bugs were found in this areea between Elroy and
477 * Mercury
478 */
479
mercury_cfg_read(struct pci_bus * bus,unsigned int devfn,int pos,int size,u32 * data)480 static int mercury_cfg_read(struct pci_bus *bus, unsigned int devfn, int pos, int size, u32 *data)
481 {
482 struct lba_device *d = LBA_DEV(parisc_walk_tree(bus->bridge));
483 u32 local_bus = (bus->parent == NULL) ? 0 : bus->busn_res.start;
484 u32 tok = LBA_CFG_TOK(local_bus, devfn);
485 void __iomem *data_reg = d->hba.base_addr + LBA_PCI_CFG_DATA;
486
487 if ((pos > 255) || (devfn > 255))
488 return -EINVAL;
489
490 LBA_CFG_TR4_ADDR_SETUP(d, tok | pos);
491 switch(size) {
492 case 1:
493 *data = READ_REG8(data_reg + (pos & 3));
494 break;
495 case 2:
496 *data = READ_REG16(data_reg + (pos & 2));
497 break;
498 case 4:
499 *data = READ_REG32(data_reg); break;
500 break;
501 }
502
503 DBG_CFG("mercury_cfg_read(%x+%2x) -> 0x%x\n", tok, pos, *data);
504 return 0;
505 }
506
507 /*
508 * LBA 4.0 config write code implements non-postable semantics
509 * by doing a read of CONFIG ADDR after the write.
510 */
511
mercury_cfg_write(struct pci_bus * bus,unsigned int devfn,int pos,int size,u32 data)512 static int mercury_cfg_write(struct pci_bus *bus, unsigned int devfn, int pos, int size, u32 data)
513 {
514 struct lba_device *d = LBA_DEV(parisc_walk_tree(bus->bridge));
515 void __iomem *data_reg = d->hba.base_addr + LBA_PCI_CFG_DATA;
516 u32 local_bus = (bus->parent == NULL) ? 0 : bus->busn_res.start;
517 u32 tok = LBA_CFG_TOK(local_bus,devfn);
518
519 if ((pos > 255) || (devfn > 255))
520 return -EINVAL;
521
522 DBG_CFG("%s(%x+%2x) <- 0x%x (c)\n", __func__, tok, pos, data);
523
524 LBA_CFG_TR4_ADDR_SETUP(d, tok | pos);
525 switch(size) {
526 case 1:
527 WRITE_REG8 (data, data_reg + (pos & 3));
528 break;
529 case 2:
530 WRITE_REG16(data, data_reg + (pos & 2));
531 break;
532 case 4:
533 WRITE_REG32(data, data_reg);
534 break;
535 }
536
537 /* flush posted write */
538 lba_t32 = READ_U32(d->hba.base_addr + LBA_PCI_CFG_ADDR);
539 return 0;
540 }
541
542 static struct pci_ops mercury_cfg_ops = {
543 .read = mercury_cfg_read,
544 .write = mercury_cfg_write,
545 };
546
547
548 static void
lba_bios_init(void)549 lba_bios_init(void)
550 {
551 DBG(MODULE_NAME ": lba_bios_init\n");
552 }
553
554
555 #ifdef CONFIG_64BIT
556
557 /*
558 * truncate_pat_collision: Deal with overlaps or outright collisions
559 * between PAT PDC reported ranges.
560 *
561 * Broken PA8800 firmware will report lmmio range that
562 * overlaps with CPU HPA. Just truncate the lmmio range.
563 *
564 * BEWARE: conflicts with this lmmio range may be an
565 * elmmio range which is pointing down another rope.
566 *
567 * FIXME: only deals with one collision per range...theoretically we
568 * could have several. Supporting more than one collision will get messy.
569 */
570 static unsigned long
truncate_pat_collision(struct resource * root,struct resource * new)571 truncate_pat_collision(struct resource *root, struct resource *new)
572 {
573 unsigned long start = new->start;
574 unsigned long end = new->end;
575 struct resource *tmp = root->child;
576
577 if (end <= start || start < root->start || !tmp)
578 return 0;
579
580 /* find first overlap */
581 while (tmp && tmp->end < start)
582 tmp = tmp->sibling;
583
584 /* no entries overlap */
585 if (!tmp) return 0;
586
587 /* found one that starts behind the new one
588 ** Don't need to do anything.
589 */
590 if (tmp->start >= end) return 0;
591
592 if (tmp->start <= start) {
593 /* "front" of new one overlaps */
594 new->start = tmp->end + 1;
595
596 if (tmp->end >= end) {
597 /* AACCKK! totally overlaps! drop this range. */
598 return 1;
599 }
600 }
601
602 if (tmp->end < end ) {
603 /* "end" of new one overlaps */
604 new->end = tmp->start - 1;
605 }
606
607 printk(KERN_WARNING "LBA: Truncating lmmio_space [%lx/%lx] "
608 "to [%lx,%lx]\n",
609 start, end,
610 (long)new->start, (long)new->end );
611
612 return 0; /* truncation successful */
613 }
614
615 /*
616 * extend_lmmio_len: extend lmmio range to maximum length
617 *
618 * This is needed at least on C8000 systems to get the ATI FireGL card
619 * working. On other systems we will currently not extend the lmmio space.
620 */
621 static unsigned long
extend_lmmio_len(unsigned long start,unsigned long end,unsigned long lba_len)622 extend_lmmio_len(unsigned long start, unsigned long end, unsigned long lba_len)
623 {
624 struct resource *tmp;
625
626 /* exit if not a C8000 */
627 if (boot_cpu_data.cpu_type < mako)
628 return end;
629
630 pr_debug("LMMIO mismatch: PAT length = 0x%lx, MASK register = 0x%lx\n",
631 end - start, lba_len);
632
633 lba_len = min(lba_len+1, 256UL*1024*1024); /* limit to 256 MB */
634
635 pr_debug("LBA: lmmio_space [0x%lx-0x%lx] - original\n", start, end);
636
637
638 end += lba_len;
639 if (end < start) /* fix overflow */
640 end = -1ULL;
641
642 pr_debug("LBA: lmmio_space [0x%lx-0x%lx] - current\n", start, end);
643
644 /* first overlap */
645 for (tmp = iomem_resource.child; tmp; tmp = tmp->sibling) {
646 pr_debug("LBA: testing %pR\n", tmp);
647 if (tmp->start == start)
648 continue; /* ignore ourself */
649 if (tmp->end < start)
650 continue;
651 if (tmp->start > end)
652 continue;
653 if (end >= tmp->start)
654 end = tmp->start - 1;
655 }
656
657 pr_info("LBA: lmmio_space [0x%lx-0x%lx] - new\n", start, end);
658
659 /* return new end */
660 return end;
661 }
662
663 #else
664 #define truncate_pat_collision(r,n) (0)
665 #endif
666
pcibios_allocate_bridge_resources(struct pci_dev * dev)667 static void pcibios_allocate_bridge_resources(struct pci_dev *dev)
668 {
669 int idx;
670 struct resource *r;
671
672 for (idx = PCI_BRIDGE_RESOURCES; idx < PCI_NUM_RESOURCES; idx++) {
673 r = &dev->resource[idx];
674 if (!r->flags)
675 continue;
676 if (r->parent) /* Already allocated */
677 continue;
678 if (!r->start || pci_claim_bridge_resource(dev, idx) < 0) {
679 /*
680 * Something is wrong with the region.
681 * Invalidate the resource to prevent
682 * child resource allocations in this
683 * range.
684 */
685 r->start = r->end = 0;
686 r->flags = 0;
687 }
688 }
689 }
690
pcibios_allocate_bus_resources(struct pci_bus * bus)691 static void pcibios_allocate_bus_resources(struct pci_bus *bus)
692 {
693 struct pci_bus *child;
694
695 /* Depth-First Search on bus tree */
696 if (bus->self)
697 pcibios_allocate_bridge_resources(bus->self);
698 list_for_each_entry(child, &bus->children, node)
699 pcibios_allocate_bus_resources(child);
700 }
701
702
703 /*
704 ** The algorithm is generic code.
705 ** But it needs to access local data structures to get the IRQ base.
706 ** Could make this a "pci_fixup_irq(bus, region)" but not sure
707 ** it's worth it.
708 **
709 ** Called by do_pci_scan_bus() immediately after each PCI bus is walked.
710 ** Resources aren't allocated until recursive buswalk below HBA is completed.
711 */
712 static void
lba_fixup_bus(struct pci_bus * bus)713 lba_fixup_bus(struct pci_bus *bus)
714 {
715 struct pci_dev *dev;
716 #ifdef FBB_SUPPORT
717 u16 status;
718 #endif
719 struct lba_device *ldev = LBA_DEV(parisc_walk_tree(bus->bridge));
720
721 DBG("lba_fixup_bus(0x%p) bus %d platform_data 0x%p\n",
722 bus, (int)bus->busn_res.start, bus->bridge->platform_data);
723
724 /*
725 ** Properly Setup MMIO resources for this bus.
726 ** pci_alloc_primary_bus() mangles this.
727 */
728 if (bus->parent) {
729 /* PCI-PCI Bridge */
730 pci_read_bridge_bases(bus);
731
732 /* check and allocate bridge resources */
733 pcibios_allocate_bus_resources(bus);
734 } else {
735 /* Host-PCI Bridge */
736 int err;
737
738 DBG("lba_fixup_bus() %s [%lx/%lx]/%lx\n",
739 ldev->hba.io_space.name,
740 ldev->hba.io_space.start, ldev->hba.io_space.end,
741 ldev->hba.io_space.flags);
742 DBG("lba_fixup_bus() %s [%lx/%lx]/%lx\n",
743 ldev->hba.lmmio_space.name,
744 ldev->hba.lmmio_space.start, ldev->hba.lmmio_space.end,
745 ldev->hba.lmmio_space.flags);
746
747 err = request_resource(&ioport_resource, &(ldev->hba.io_space));
748 if (err < 0) {
749 lba_dump_res(&ioport_resource, 2);
750 BUG();
751 }
752
753 if (ldev->hba.elmmio_space.flags) {
754 err = request_resource(&iomem_resource,
755 &(ldev->hba.elmmio_space));
756 if (err < 0) {
757
758 printk("FAILED: lba_fixup_bus() request for "
759 "elmmio_space [%lx/%lx]\n",
760 (long)ldev->hba.elmmio_space.start,
761 (long)ldev->hba.elmmio_space.end);
762
763 /* lba_dump_res(&iomem_resource, 2); */
764 /* BUG(); */
765 }
766 }
767
768 if (ldev->hba.lmmio_space.flags) {
769 err = request_resource(&iomem_resource, &(ldev->hba.lmmio_space));
770 if (err < 0) {
771 printk(KERN_ERR "FAILED: lba_fixup_bus() request for "
772 "lmmio_space [%lx/%lx]\n",
773 (long)ldev->hba.lmmio_space.start,
774 (long)ldev->hba.lmmio_space.end);
775 }
776 }
777
778 #ifdef CONFIG_64BIT
779 /* GMMIO is distributed range. Every LBA/Rope gets part it. */
780 if (ldev->hba.gmmio_space.flags) {
781 err = request_resource(&iomem_resource, &(ldev->hba.gmmio_space));
782 if (err < 0) {
783 printk("FAILED: lba_fixup_bus() request for "
784 "gmmio_space [%lx/%lx]\n",
785 (long)ldev->hba.gmmio_space.start,
786 (long)ldev->hba.gmmio_space.end);
787 lba_dump_res(&iomem_resource, 2);
788 BUG();
789 }
790 }
791 #endif
792
793 }
794
795 list_for_each_entry(dev, &bus->devices, bus_list) {
796 int i;
797
798 DBG("lba_fixup_bus() %s\n", pci_name(dev));
799
800 /* Virtualize Device/Bridge Resources. */
801 for (i = 0; i < PCI_BRIDGE_RESOURCES; i++) {
802 struct resource *res = &dev->resource[i];
803
804 /* If resource not allocated - skip it */
805 if (!res->start)
806 continue;
807
808 /*
809 ** FIXME: this will result in whinging for devices
810 ** that share expansion ROMs (think quad tulip), but
811 ** isn't harmful.
812 */
813 pci_claim_resource(dev, i);
814 }
815
816 #ifdef FBB_SUPPORT
817 /*
818 ** If one device does not support FBB transfers,
819 ** No one on the bus can be allowed to use them.
820 */
821 (void) pci_read_config_word(dev, PCI_STATUS, &status);
822 bus->bridge_ctl &= ~(status & PCI_STATUS_FAST_BACK);
823 #endif
824
825 /*
826 ** P2PB's have no IRQs. ignore them.
827 */
828 if ((dev->class >> 8) == PCI_CLASS_BRIDGE_PCI) {
829 pcibios_init_bridge(dev);
830 continue;
831 }
832
833 /* Adjust INTERRUPT_LINE for this dev */
834 iosapic_fixup_irq(ldev->iosapic_obj, dev);
835 }
836
837 #ifdef FBB_SUPPORT
838 /* FIXME/REVISIT - finish figuring out to set FBB on both
839 ** pci_setup_bridge() clobbers PCI_BRIDGE_CONTROL.
840 ** Can't fixup here anyway....garr...
841 */
842 if (fbb_enable) {
843 if (bus->parent) {
844 u8 control;
845 /* enable on PPB */
846 (void) pci_read_config_byte(bus->self, PCI_BRIDGE_CONTROL, &control);
847 (void) pci_write_config_byte(bus->self, PCI_BRIDGE_CONTROL, control | PCI_STATUS_FAST_BACK);
848
849 } else {
850 /* enable on LBA */
851 }
852 fbb_enable = PCI_COMMAND_FAST_BACK;
853 }
854
855 /* Lastly enable FBB/PERR/SERR on all devices too */
856 list_for_each_entry(dev, &bus->devices, bus_list) {
857 (void) pci_read_config_word(dev, PCI_COMMAND, &status);
858 status |= PCI_COMMAND_PARITY | PCI_COMMAND_SERR | fbb_enable;
859 (void) pci_write_config_word(dev, PCI_COMMAND, status);
860 }
861 #endif
862 }
863
864
865 static struct pci_bios_ops lba_bios_ops = {
866 .init = lba_bios_init,
867 .fixup_bus = lba_fixup_bus,
868 };
869
870
871
872
873 /*******************************************************
874 **
875 ** LBA Sprockets "I/O Port" Space Accessor Functions
876 **
877 ** This set of accessor functions is intended for use with
878 ** "legacy firmware" (ie Sprockets on Allegro/Forte boxes).
879 **
880 ** Many PCI devices don't require use of I/O port space (eg Tulip,
881 ** NCR720) since they export the same registers to both MMIO and
882 ** I/O port space. In general I/O port space is slower than
883 ** MMIO since drivers are designed so PIO writes can be posted.
884 **
885 ********************************************************/
886
887 #define LBA_PORT_IN(size, mask) \
888 static u##size lba_astro_in##size (struct pci_hba_data *d, u16 addr) \
889 { \
890 u##size t; \
891 t = READ_REG##size(astro_iop_base + addr); \
892 DBG_PORT(" 0x%x\n", t); \
893 return (t); \
894 }
895
896 LBA_PORT_IN( 8, 3)
897 LBA_PORT_IN(16, 2)
898 LBA_PORT_IN(32, 0)
899
900
901
902 /*
903 ** BUG X4107: Ordering broken - DMA RD return can bypass PIO WR
904 **
905 ** Fixed in Elroy 2.2. The READ_U32(..., LBA_FUNC_ID) below is
906 ** guarantee non-postable completion semantics - not avoid X4107.
907 ** The READ_U32 only guarantees the write data gets to elroy but
908 ** out to the PCI bus. We can't read stuff from I/O port space
909 ** since we don't know what has side-effects. Attempting to read
910 ** from configuration space would be suicidal given the number of
911 ** bugs in that elroy functionality.
912 **
913 ** Description:
914 ** DMA read results can improperly pass PIO writes (X4107). The
915 ** result of this bug is that if a processor modifies a location in
916 ** memory after having issued PIO writes, the PIO writes are not
917 ** guaranteed to be completed before a PCI device is allowed to see
918 ** the modified data in a DMA read.
919 **
920 ** Note that IKE bug X3719 in TR1 IKEs will result in the same
921 ** symptom.
922 **
923 ** Workaround:
924 ** The workaround for this bug is to always follow a PIO write with
925 ** a PIO read to the same bus before starting DMA on that PCI bus.
926 **
927 */
928 #define LBA_PORT_OUT(size, mask) \
929 static void lba_astro_out##size (struct pci_hba_data *d, u16 addr, u##size val) \
930 { \
931 DBG_PORT("%s(0x%p, 0x%x, 0x%x)\n", __func__, d, addr, val); \
932 WRITE_REG##size(val, astro_iop_base + addr); \
933 if (LBA_DEV(d)->hw_rev < 3) \
934 lba_t32 = READ_U32(d->base_addr + LBA_FUNC_ID); \
935 }
936
937 LBA_PORT_OUT( 8, 3)
938 LBA_PORT_OUT(16, 2)
939 LBA_PORT_OUT(32, 0)
940
941
942 static struct pci_port_ops lba_astro_port_ops = {
943 .inb = lba_astro_in8,
944 .inw = lba_astro_in16,
945 .inl = lba_astro_in32,
946 .outb = lba_astro_out8,
947 .outw = lba_astro_out16,
948 .outl = lba_astro_out32
949 };
950
951
952 #ifdef CONFIG_64BIT
953 #define PIOP_TO_GMMIO(lba, addr) \
954 ((lba)->iop_base + (((addr)&0xFFFC)<<10) + ((addr)&3))
955
956 /*******************************************************
957 **
958 ** LBA PAT "I/O Port" Space Accessor Functions
959 **
960 ** This set of accessor functions is intended for use with
961 ** "PAT PDC" firmware (ie Prelude/Rhapsody/Piranha boxes).
962 **
963 ** This uses the PIOP space located in the first 64MB of GMMIO.
964 ** Each rope gets a full 64*KB* (ie 4 bytes per page) this way.
965 ** bits 1:0 stay the same. bits 15:2 become 25:12.
966 ** Then add the base and we can generate an I/O Port cycle.
967 ********************************************************/
968 #undef LBA_PORT_IN
969 #define LBA_PORT_IN(size, mask) \
970 static u##size lba_pat_in##size (struct pci_hba_data *l, u16 addr) \
971 { \
972 u##size t; \
973 DBG_PORT("%s(0x%p, 0x%x) ->", __func__, l, addr); \
974 t = READ_REG##size(PIOP_TO_GMMIO(LBA_DEV(l), addr)); \
975 DBG_PORT(" 0x%x\n", t); \
976 return (t); \
977 }
978
979 LBA_PORT_IN( 8, 3)
980 LBA_PORT_IN(16, 2)
981 LBA_PORT_IN(32, 0)
982
983
984 #undef LBA_PORT_OUT
985 #define LBA_PORT_OUT(size, mask) \
986 static void lba_pat_out##size (struct pci_hba_data *l, u16 addr, u##size val) \
987 { \
988 void __iomem *where = PIOP_TO_GMMIO(LBA_DEV(l), addr); \
989 DBG_PORT("%s(0x%p, 0x%x, 0x%x)\n", __func__, l, addr, val); \
990 WRITE_REG##size(val, where); \
991 /* flush the I/O down to the elroy at least */ \
992 lba_t32 = READ_U32(l->base_addr + LBA_FUNC_ID); \
993 }
994
995 LBA_PORT_OUT( 8, 3)
996 LBA_PORT_OUT(16, 2)
997 LBA_PORT_OUT(32, 0)
998
999
1000 static struct pci_port_ops lba_pat_port_ops = {
1001 .inb = lba_pat_in8,
1002 .inw = lba_pat_in16,
1003 .inl = lba_pat_in32,
1004 .outb = lba_pat_out8,
1005 .outw = lba_pat_out16,
1006 .outl = lba_pat_out32
1007 };
1008
1009
1010
1011 /*
1012 ** make range information from PDC available to PCI subsystem.
1013 ** We make the PDC call here in order to get the PCI bus range
1014 ** numbers. The rest will get forwarded in pcibios_fixup_bus().
1015 ** We don't have a struct pci_bus assigned to us yet.
1016 */
1017 static void
lba_pat_resources(struct parisc_device * pa_dev,struct lba_device * lba_dev)1018 lba_pat_resources(struct parisc_device *pa_dev, struct lba_device *lba_dev)
1019 {
1020 unsigned long bytecnt;
1021 long io_count;
1022 long status; /* PDC return status */
1023 long pa_count;
1024 pdc_pat_cell_mod_maddr_block_t *pa_pdc_cell; /* PA_VIEW */
1025 pdc_pat_cell_mod_maddr_block_t *io_pdc_cell; /* IO_VIEW */
1026 int i;
1027
1028 pa_pdc_cell = kzalloc(sizeof(pdc_pat_cell_mod_maddr_block_t), GFP_KERNEL);
1029 if (!pa_pdc_cell)
1030 return;
1031
1032 io_pdc_cell = kzalloc(sizeof(pdc_pat_cell_mod_maddr_block_t), GFP_KERNEL);
1033 if (!io_pdc_cell) {
1034 kfree(pa_pdc_cell);
1035 return;
1036 }
1037
1038 /* return cell module (IO view) */
1039 status = pdc_pat_cell_module(&bytecnt, pa_dev->pcell_loc, pa_dev->mod_index,
1040 PA_VIEW, pa_pdc_cell);
1041 pa_count = pa_pdc_cell->mod[1];
1042
1043 status |= pdc_pat_cell_module(&bytecnt, pa_dev->pcell_loc, pa_dev->mod_index,
1044 IO_VIEW, io_pdc_cell);
1045 io_count = io_pdc_cell->mod[1];
1046
1047 /* We've already done this once for device discovery...*/
1048 if (status != PDC_OK) {
1049 panic("pdc_pat_cell_module() call failed for LBA!\n");
1050 }
1051
1052 if (PAT_GET_ENTITY(pa_pdc_cell->mod_info) != PAT_ENTITY_LBA) {
1053 panic("pdc_pat_cell_module() entity returned != PAT_ENTITY_LBA!\n");
1054 }
1055
1056 /*
1057 ** Inspect the resources PAT tells us about
1058 */
1059 for (i = 0; i < pa_count; i++) {
1060 struct {
1061 unsigned long type;
1062 unsigned long start;
1063 unsigned long end; /* aka finish */
1064 } *p, *io;
1065 struct resource *r;
1066
1067 p = (void *) &(pa_pdc_cell->mod[2+i*3]);
1068 io = (void *) &(io_pdc_cell->mod[2+i*3]);
1069
1070 /* Convert the PAT range data to PCI "struct resource" */
1071 switch(p->type & 0xff) {
1072 case PAT_PBNUM:
1073 lba_dev->hba.bus_num.start = p->start;
1074 lba_dev->hba.bus_num.end = p->end;
1075 lba_dev->hba.bus_num.flags = IORESOURCE_BUS;
1076 break;
1077
1078 case PAT_LMMIO:
1079 /* used to fix up pre-initialized MEM BARs */
1080 if (!lba_dev->hba.lmmio_space.flags) {
1081 unsigned long lba_len;
1082
1083 lba_len = ~READ_REG32(lba_dev->hba.base_addr
1084 + LBA_LMMIO_MASK);
1085 if ((p->end - p->start) != lba_len)
1086 p->end = extend_lmmio_len(p->start,
1087 p->end, lba_len);
1088
1089 sprintf(lba_dev->hba.lmmio_name,
1090 "PCI%02x LMMIO",
1091 (int)lba_dev->hba.bus_num.start);
1092 lba_dev->hba.lmmio_space_offset = p->start -
1093 io->start;
1094 r = &lba_dev->hba.lmmio_space;
1095 r->name = lba_dev->hba.lmmio_name;
1096 } else if (!lba_dev->hba.elmmio_space.flags) {
1097 sprintf(lba_dev->hba.elmmio_name,
1098 "PCI%02x ELMMIO",
1099 (int)lba_dev->hba.bus_num.start);
1100 r = &lba_dev->hba.elmmio_space;
1101 r->name = lba_dev->hba.elmmio_name;
1102 } else {
1103 printk(KERN_WARNING MODULE_NAME
1104 " only supports 2 LMMIO resources!\n");
1105 break;
1106 }
1107
1108 r->start = p->start;
1109 r->end = p->end;
1110 r->flags = IORESOURCE_MEM;
1111 r->parent = r->sibling = r->child = NULL;
1112 break;
1113
1114 case PAT_GMMIO:
1115 /* MMIO space > 4GB phys addr; for 64-bit BAR */
1116 sprintf(lba_dev->hba.gmmio_name, "PCI%02x GMMIO",
1117 (int)lba_dev->hba.bus_num.start);
1118 r = &lba_dev->hba.gmmio_space;
1119 r->name = lba_dev->hba.gmmio_name;
1120 r->start = p->start;
1121 r->end = p->end;
1122 r->flags = IORESOURCE_MEM;
1123 r->parent = r->sibling = r->child = NULL;
1124 break;
1125
1126 case PAT_NPIOP:
1127 printk(KERN_WARNING MODULE_NAME
1128 " range[%d] : ignoring NPIOP (0x%lx)\n",
1129 i, p->start);
1130 break;
1131
1132 case PAT_PIOP:
1133 /*
1134 ** Postable I/O port space is per PCI host adapter.
1135 ** base of 64MB PIOP region
1136 */
1137 lba_dev->iop_base = ioremap(p->start, 64 * 1024 * 1024);
1138
1139 sprintf(lba_dev->hba.io_name, "PCI%02x Ports",
1140 (int)lba_dev->hba.bus_num.start);
1141 r = &lba_dev->hba.io_space;
1142 r->name = lba_dev->hba.io_name;
1143 r->start = HBA_PORT_BASE(lba_dev->hba.hba_num);
1144 r->end = r->start + HBA_PORT_SPACE_SIZE - 1;
1145 r->flags = IORESOURCE_IO;
1146 r->parent = r->sibling = r->child = NULL;
1147 break;
1148
1149 default:
1150 printk(KERN_WARNING MODULE_NAME
1151 " range[%d] : unknown pat range type (0x%lx)\n",
1152 i, p->type & 0xff);
1153 break;
1154 }
1155 }
1156
1157 kfree(pa_pdc_cell);
1158 kfree(io_pdc_cell);
1159 }
1160 #else
1161 /* keep compiler from complaining about missing declarations */
1162 #define lba_pat_port_ops lba_astro_port_ops
1163 #define lba_pat_resources(pa_dev, lba_dev)
1164 #endif /* CONFIG_64BIT */
1165
1166
1167 extern void sba_distributed_lmmio(struct parisc_device *, struct resource *);
1168 extern void sba_directed_lmmio(struct parisc_device *, struct resource *);
1169
1170
1171 static void
lba_legacy_resources(struct parisc_device * pa_dev,struct lba_device * lba_dev)1172 lba_legacy_resources(struct parisc_device *pa_dev, struct lba_device *lba_dev)
1173 {
1174 struct resource *r;
1175 int lba_num;
1176
1177 lba_dev->hba.lmmio_space_offset = PCI_F_EXTEND;
1178
1179 /*
1180 ** With "legacy" firmware, the lowest byte of FW_SCRATCH
1181 ** represents bus->secondary and the second byte represents
1182 ** bus->subsidiary (i.e. highest PPB programmed by firmware).
1183 ** PCI bus walk *should* end up with the same result.
1184 ** FIXME: But we don't have sanity checks in PCI or LBA.
1185 */
1186 lba_num = READ_REG32(lba_dev->hba.base_addr + LBA_FW_SCRATCH);
1187 r = &(lba_dev->hba.bus_num);
1188 r->name = "LBA PCI Busses";
1189 r->start = lba_num & 0xff;
1190 r->end = (lba_num>>8) & 0xff;
1191 r->flags = IORESOURCE_BUS;
1192
1193 /* Set up local PCI Bus resources - we don't need them for
1194 ** Legacy boxes but it's nice to see in /proc/iomem.
1195 */
1196 r = &(lba_dev->hba.lmmio_space);
1197 sprintf(lba_dev->hba.lmmio_name, "PCI%02x LMMIO",
1198 (int)lba_dev->hba.bus_num.start);
1199 r->name = lba_dev->hba.lmmio_name;
1200
1201 #if 1
1202 /* We want the CPU -> IO routing of addresses.
1203 * The SBA BASE/MASK registers control CPU -> IO routing.
1204 * Ask SBA what is routed to this rope/LBA.
1205 */
1206 sba_distributed_lmmio(pa_dev, r);
1207 #else
1208 /*
1209 * The LBA BASE/MASK registers control IO -> System routing.
1210 *
1211 * The following code works but doesn't get us what we want.
1212 * Well, only because firmware (v5.0) on C3000 doesn't program
1213 * the LBA BASE/MASE registers to be the exact inverse of
1214 * the corresponding SBA registers. Other Astro/Pluto
1215 * based platform firmware may do it right.
1216 *
1217 * Should someone want to mess with MSI, they may need to
1218 * reprogram LBA BASE/MASK registers. Thus preserve the code
1219 * below until MSI is known to work on C3000/A500/N4000/RP3440.
1220 *
1221 * Using the code below, /proc/iomem shows:
1222 * ...
1223 * f0000000-f0ffffff : PCI00 LMMIO
1224 * f05d0000-f05d0000 : lcd_data
1225 * f05d0008-f05d0008 : lcd_cmd
1226 * f1000000-f1ffffff : PCI01 LMMIO
1227 * f4000000-f4ffffff : PCI02 LMMIO
1228 * f4000000-f4001fff : sym53c8xx
1229 * f4002000-f4003fff : sym53c8xx
1230 * f4004000-f40043ff : sym53c8xx
1231 * f4005000-f40053ff : sym53c8xx
1232 * f4007000-f4007fff : ohci_hcd
1233 * f4008000-f40083ff : tulip
1234 * f6000000-f6ffffff : PCI03 LMMIO
1235 * f8000000-fbffffff : PCI00 ELMMIO
1236 * fa100000-fa4fffff : stifb mmio
1237 * fb000000-fb1fffff : stifb fb
1238 *
1239 * But everything listed under PCI02 actually lives under PCI00.
1240 * This is clearly wrong.
1241 *
1242 * Asking SBA how things are routed tells the correct story:
1243 * LMMIO_BASE/MASK/ROUTE f4000001 fc000000 00000000
1244 * DIR0_BASE/MASK/ROUTE fa000001 fe000000 00000006
1245 * DIR1_BASE/MASK/ROUTE f9000001 ff000000 00000004
1246 * DIR2_BASE/MASK/ROUTE f0000000 fc000000 00000000
1247 * DIR3_BASE/MASK/ROUTE f0000000 fc000000 00000000
1248 *
1249 * Which looks like this in /proc/iomem:
1250 * f4000000-f47fffff : PCI00 LMMIO
1251 * f4000000-f4001fff : sym53c8xx
1252 * ...[deteled core devices - same as above]...
1253 * f4008000-f40083ff : tulip
1254 * f4800000-f4ffffff : PCI01 LMMIO
1255 * f6000000-f67fffff : PCI02 LMMIO
1256 * f7000000-f77fffff : PCI03 LMMIO
1257 * f9000000-f9ffffff : PCI02 ELMMIO
1258 * fa000000-fbffffff : PCI03 ELMMIO
1259 * fa100000-fa4fffff : stifb mmio
1260 * fb000000-fb1fffff : stifb fb
1261 *
1262 * ie all Built-in core are under now correctly under PCI00.
1263 * The "PCI02 ELMMIO" directed range is for:
1264 * +-[02]---03.0 3Dfx Interactive, Inc. Voodoo 2
1265 *
1266 * All is well now.
1267 */
1268 r->start = READ_REG32(lba_dev->hba.base_addr + LBA_LMMIO_BASE);
1269 if (r->start & 1) {
1270 unsigned long rsize;
1271
1272 r->flags = IORESOURCE_MEM;
1273 /* mmio_mask also clears Enable bit */
1274 r->start &= mmio_mask;
1275 r->start = PCI_HOST_ADDR(&lba_dev->hba, r->start);
1276 rsize = ~ READ_REG32(lba_dev->hba.base_addr + LBA_LMMIO_MASK);
1277
1278 /*
1279 ** Each rope only gets part of the distributed range.
1280 ** Adjust "window" for this rope.
1281 */
1282 rsize /= ROPES_PER_IOC;
1283 r->start += (rsize + 1) * LBA_NUM(pa_dev->hpa.start);
1284 r->end = r->start + rsize;
1285 } else {
1286 r->end = r->start = 0; /* Not enabled. */
1287 }
1288 #endif
1289
1290 /*
1291 ** "Directed" ranges are used when the "distributed range" isn't
1292 ** sufficient for all devices below a given LBA. Typically devices
1293 ** like graphics cards or X25 may need a directed range when the
1294 ** bus has multiple slots (ie multiple devices) or the device
1295 ** needs more than the typical 4 or 8MB a distributed range offers.
1296 **
1297 ** The main reason for ignoring it now frigging complications.
1298 ** Directed ranges may overlap (and have precedence) over
1299 ** distributed ranges. Or a distributed range assigned to a unused
1300 ** rope may be used by a directed range on a different rope.
1301 ** Support for graphics devices may require fixing this
1302 ** since they may be assigned a directed range which overlaps
1303 ** an existing (but unused portion of) distributed range.
1304 */
1305 r = &(lba_dev->hba.elmmio_space);
1306 sprintf(lba_dev->hba.elmmio_name, "PCI%02x ELMMIO",
1307 (int)lba_dev->hba.bus_num.start);
1308 r->name = lba_dev->hba.elmmio_name;
1309
1310 #if 1
1311 /* See comment which precedes call to sba_directed_lmmio() */
1312 sba_directed_lmmio(pa_dev, r);
1313 #else
1314 r->start = READ_REG32(lba_dev->hba.base_addr + LBA_ELMMIO_BASE);
1315
1316 if (r->start & 1) {
1317 unsigned long rsize;
1318 r->flags = IORESOURCE_MEM;
1319 /* mmio_mask also clears Enable bit */
1320 r->start &= mmio_mask;
1321 r->start = PCI_HOST_ADDR(&lba_dev->hba, r->start);
1322 rsize = READ_REG32(lba_dev->hba.base_addr + LBA_ELMMIO_MASK);
1323 r->end = r->start + ~rsize;
1324 }
1325 #endif
1326
1327 r = &(lba_dev->hba.io_space);
1328 sprintf(lba_dev->hba.io_name, "PCI%02x Ports",
1329 (int)lba_dev->hba.bus_num.start);
1330 r->name = lba_dev->hba.io_name;
1331 r->flags = IORESOURCE_IO;
1332 r->start = READ_REG32(lba_dev->hba.base_addr + LBA_IOS_BASE) & ~1L;
1333 r->end = r->start + (READ_REG32(lba_dev->hba.base_addr + LBA_IOS_MASK) ^ (HBA_PORT_SPACE_SIZE - 1));
1334
1335 /* Virtualize the I/O Port space ranges */
1336 lba_num = HBA_PORT_BASE(lba_dev->hba.hba_num);
1337 r->start |= lba_num;
1338 r->end |= lba_num;
1339 }
1340
1341
1342 /**************************************************************************
1343 **
1344 ** LBA initialization code (HW and SW)
1345 **
1346 ** o identify LBA chip itself
1347 ** o initialize LBA chip modes (HardFail)
1348 ** o FIXME: initialize DMA hints for reasonable defaults
1349 ** o enable configuration functions
1350 ** o call pci_register_ops() to discover devs (fixup/fixup_bus get invoked)
1351 **
1352 **************************************************************************/
1353
1354 static int __init
lba_hw_init(struct lba_device * d)1355 lba_hw_init(struct lba_device *d)
1356 {
1357 u32 stat;
1358 u32 bus_reset; /* PDC_PAT_BUG */
1359
1360 #if 0
1361 printk(KERN_DEBUG "LBA %lx STAT_CTL %Lx ERROR_CFG %Lx STATUS %Lx DMA_CTL %Lx\n",
1362 d->hba.base_addr,
1363 READ_REG64(d->hba.base_addr + LBA_STAT_CTL),
1364 READ_REG64(d->hba.base_addr + LBA_ERROR_CONFIG),
1365 READ_REG64(d->hba.base_addr + LBA_ERROR_STATUS),
1366 READ_REG64(d->hba.base_addr + LBA_DMA_CTL) );
1367 printk(KERN_DEBUG " ARB mask %Lx pri %Lx mode %Lx mtlt %Lx\n",
1368 READ_REG64(d->hba.base_addr + LBA_ARB_MASK),
1369 READ_REG64(d->hba.base_addr + LBA_ARB_PRI),
1370 READ_REG64(d->hba.base_addr + LBA_ARB_MODE),
1371 READ_REG64(d->hba.base_addr + LBA_ARB_MTLT) );
1372 printk(KERN_DEBUG " HINT cfg 0x%Lx\n",
1373 READ_REG64(d->hba.base_addr + LBA_HINT_CFG));
1374 printk(KERN_DEBUG " HINT reg ");
1375 { int i;
1376 for (i=LBA_HINT_BASE; i< (14*8 + LBA_HINT_BASE); i+=8)
1377 printk(" %Lx", READ_REG64(d->hba.base_addr + i));
1378 }
1379 printk("\n");
1380 #endif /* DEBUG_LBA_PAT */
1381
1382 #ifdef CONFIG_64BIT
1383 /*
1384 * FIXME add support for PDC_PAT_IO "Get slot status" - OLAR support
1385 * Only N-Class and up can really make use of Get slot status.
1386 * maybe L-class too but I've never played with it there.
1387 */
1388 #endif
1389
1390 /* PDC_PAT_BUG: exhibited in rev 40.48 on L2000 */
1391 bus_reset = READ_REG32(d->hba.base_addr + LBA_STAT_CTL + 4) & 1;
1392 if (bus_reset) {
1393 printk(KERN_DEBUG "NOTICE: PCI bus reset still asserted! (clearing)\n");
1394 }
1395
1396 stat = READ_REG32(d->hba.base_addr + LBA_ERROR_CONFIG);
1397 if (stat & LBA_SMART_MODE) {
1398 printk(KERN_DEBUG "NOTICE: LBA in SMART mode! (cleared)\n");
1399 stat &= ~LBA_SMART_MODE;
1400 WRITE_REG32(stat, d->hba.base_addr + LBA_ERROR_CONFIG);
1401 }
1402
1403
1404 /*
1405 * Hard Fail vs. Soft Fail on PCI "Master Abort".
1406 *
1407 * "Master Abort" means the MMIO transaction timed out - usually due to
1408 * the device not responding to an MMIO read. We would like HF to be
1409 * enabled to find driver problems, though it means the system will
1410 * crash with a HPMC.
1411 *
1412 * In SoftFail mode "~0L" is returned as a result of a timeout on the
1413 * pci bus. This is like how PCI busses on x86 and most other
1414 * architectures behave. In order to increase compatibility with
1415 * existing (x86) PCI hardware and existing Linux drivers we enable
1416 * Soft Faul mode on PA-RISC now too.
1417 */
1418 stat = READ_REG32(d->hba.base_addr + LBA_STAT_CTL);
1419 #if defined(ENABLE_HARDFAIL)
1420 WRITE_REG32(stat | HF_ENABLE, d->hba.base_addr + LBA_STAT_CTL);
1421 #else
1422 WRITE_REG32(stat & ~HF_ENABLE, d->hba.base_addr + LBA_STAT_CTL);
1423 #endif
1424
1425 /*
1426 ** Writing a zero to STAT_CTL.rf (bit 0) will clear reset signal
1427 ** if it's not already set. If we just cleared the PCI Bus Reset
1428 ** signal, wait a bit for the PCI devices to recover and setup.
1429 */
1430 if (bus_reset)
1431 mdelay(pci_post_reset_delay);
1432
1433 if (0 == READ_REG32(d->hba.base_addr + LBA_ARB_MASK)) {
1434 /*
1435 ** PDC_PAT_BUG: PDC rev 40.48 on L2000.
1436 ** B2000/C3600/J6000 also have this problem?
1437 **
1438 ** Elroys with hot pluggable slots don't get configured
1439 ** correctly if the slot is empty. ARB_MASK is set to 0
1440 ** and we can't master transactions on the bus if it's
1441 ** not at least one. 0x3 enables elroy and first slot.
1442 */
1443 printk(KERN_DEBUG "NOTICE: Enabling PCI Arbitration\n");
1444 WRITE_REG32(0x3, d->hba.base_addr + LBA_ARB_MASK);
1445 }
1446
1447 /*
1448 ** FIXME: Hint registers are programmed with default hint
1449 ** values by firmware. Hints should be sane even if we
1450 ** can't reprogram them the way drivers want.
1451 */
1452 return 0;
1453 }
1454
1455 /*
1456 * Unfortunately, when firmware numbers busses, it doesn't take into account
1457 * Cardbus bridges. So we have to renumber the busses to suit ourselves.
1458 * Elroy/Mercury don't actually know what bus number they're attached to;
1459 * we use bus 0 to indicate the directly attached bus and any other bus
1460 * number will be taken care of by the PCI-PCI bridge.
1461 */
1462 static unsigned int lba_next_bus = 0;
1463
1464 /*
1465 * Determine if lba should claim this chip (return 0) or not (return 1).
1466 * If so, initialize the chip and tell other partners in crime they
1467 * have work to do.
1468 */
1469 static int __init
lba_driver_probe(struct parisc_device * dev)1470 lba_driver_probe(struct parisc_device *dev)
1471 {
1472 struct lba_device *lba_dev;
1473 LIST_HEAD(resources);
1474 struct pci_bus *lba_bus;
1475 struct pci_ops *cfg_ops;
1476 u32 func_class;
1477 void *tmp_obj;
1478 char *version;
1479 void __iomem *addr;
1480 int max;
1481
1482 addr = ioremap(dev->hpa.start, 4096);
1483 if (addr == NULL)
1484 return -ENOMEM;
1485
1486 /* Read HW Rev First */
1487 func_class = READ_REG32(addr + LBA_FCLASS);
1488
1489 if (IS_ELROY(dev)) {
1490 func_class &= 0xf;
1491 switch (func_class) {
1492 case 0: version = "TR1.0"; break;
1493 case 1: version = "TR2.0"; break;
1494 case 2: version = "TR2.1"; break;
1495 case 3: version = "TR2.2"; break;
1496 case 4: version = "TR3.0"; break;
1497 case 5: version = "TR4.0"; break;
1498 default: version = "TR4+";
1499 }
1500
1501 printk(KERN_INFO "Elroy version %s (0x%x) found at 0x%lx\n",
1502 version, func_class & 0xf, (long)dev->hpa.start);
1503
1504 if (func_class < 2) {
1505 printk(KERN_WARNING "Can't support LBA older than "
1506 "TR2.1 - continuing under adversity.\n");
1507 }
1508
1509 #if 0
1510 /* Elroy TR4.0 should work with simple algorithm.
1511 But it doesn't. Still missing something. *sigh*
1512 */
1513 if (func_class > 4) {
1514 cfg_ops = &mercury_cfg_ops;
1515 } else
1516 #endif
1517 {
1518 cfg_ops = &elroy_cfg_ops;
1519 }
1520
1521 } else if (IS_MERCURY(dev) || IS_QUICKSILVER(dev)) {
1522 int major, minor;
1523
1524 func_class &= 0xff;
1525 major = func_class >> 4, minor = func_class & 0xf;
1526
1527 /* We could use one printk for both Elroy and Mercury,
1528 * but for the mask for func_class.
1529 */
1530 printk(KERN_INFO "%s version TR%d.%d (0x%x) found at 0x%lx\n",
1531 IS_MERCURY(dev) ? "Mercury" : "Quicksilver", major,
1532 minor, func_class, (long)dev->hpa.start);
1533
1534 cfg_ops = &mercury_cfg_ops;
1535 } else {
1536 printk(KERN_ERR "Unknown LBA found at 0x%lx\n",
1537 (long)dev->hpa.start);
1538 return -ENODEV;
1539 }
1540
1541 /* Tell I/O SAPIC driver we have a IRQ handler/region. */
1542 tmp_obj = iosapic_register(dev->hpa.start + LBA_IOSAPIC_BASE);
1543
1544 /* NOTE: PCI devices (e.g. 103c:1005 graphics card) which don't
1545 ** have an IRT entry will get NULL back from iosapic code.
1546 */
1547
1548 lba_dev = kzalloc(sizeof(struct lba_device), GFP_KERNEL);
1549 if (!lba_dev) {
1550 printk(KERN_ERR "lba_init_chip - couldn't alloc lba_device\n");
1551 return(1);
1552 }
1553
1554
1555 /* ---------- First : initialize data we already have --------- */
1556
1557 lba_dev->hw_rev = func_class;
1558 lba_dev->hba.base_addr = addr;
1559 lba_dev->hba.dev = dev;
1560 lba_dev->iosapic_obj = tmp_obj; /* save interrupt handle */
1561 lba_dev->hba.iommu = sba_get_iommu(dev); /* get iommu data */
1562 parisc_set_drvdata(dev, lba_dev);
1563
1564 /* ------------ Second : initialize common stuff ---------- */
1565 pci_bios = &lba_bios_ops;
1566 pcibios_register_hba(&lba_dev->hba);
1567 spin_lock_init(&lba_dev->lba_lock);
1568
1569 if (lba_hw_init(lba_dev))
1570 return(1);
1571
1572 /* ---------- Third : setup I/O Port and MMIO resources --------- */
1573
1574 if (is_pdc_pat()) {
1575 /* PDC PAT firmware uses PIOP region of GMMIO space. */
1576 pci_port = &lba_pat_port_ops;
1577 /* Go ask PDC PAT what resources this LBA has */
1578 lba_pat_resources(dev, lba_dev);
1579 } else {
1580 if (!astro_iop_base) {
1581 /* Sprockets PDC uses NPIOP region */
1582 astro_iop_base = ioremap(LBA_PORT_BASE, 64 * 1024);
1583 pci_port = &lba_astro_port_ops;
1584 }
1585
1586 /* Poke the chip a bit for /proc output */
1587 lba_legacy_resources(dev, lba_dev);
1588 }
1589
1590 if (lba_dev->hba.bus_num.start < lba_next_bus)
1591 lba_dev->hba.bus_num.start = lba_next_bus;
1592
1593 /* Overlaps with elmmio can (and should) fail here.
1594 * We will prune (or ignore) the distributed range.
1595 *
1596 * FIXME: SBA code should register all elmmio ranges first.
1597 * that would take care of elmmio ranges routed
1598 * to a different rope (already discovered) from
1599 * getting registered *after* LBA code has already
1600 * registered it's distributed lmmio range.
1601 */
1602 if (truncate_pat_collision(&iomem_resource,
1603 &(lba_dev->hba.lmmio_space))) {
1604 printk(KERN_WARNING "LBA: lmmio_space [%lx/%lx] duplicate!\n",
1605 (long)lba_dev->hba.lmmio_space.start,
1606 (long)lba_dev->hba.lmmio_space.end);
1607 lba_dev->hba.lmmio_space.flags = 0;
1608 }
1609
1610 pci_add_resource_offset(&resources, &lba_dev->hba.io_space,
1611 HBA_PORT_BASE(lba_dev->hba.hba_num));
1612 if (lba_dev->hba.elmmio_space.flags)
1613 pci_add_resource_offset(&resources, &lba_dev->hba.elmmio_space,
1614 lba_dev->hba.lmmio_space_offset);
1615 if (lba_dev->hba.lmmio_space.flags)
1616 pci_add_resource_offset(&resources, &lba_dev->hba.lmmio_space,
1617 lba_dev->hba.lmmio_space_offset);
1618 if (lba_dev->hba.gmmio_space.flags) {
1619 /* Not registering GMMIO space - according to docs it's not
1620 * even used on HP-UX. */
1621 /* pci_add_resource(&resources, &lba_dev->hba.gmmio_space); */
1622 }
1623
1624 pci_add_resource(&resources, &lba_dev->hba.bus_num);
1625
1626 dev->dev.platform_data = lba_dev;
1627 lba_bus = lba_dev->hba.hba_bus =
1628 pci_create_root_bus(&dev->dev, lba_dev->hba.bus_num.start,
1629 cfg_ops, NULL, &resources);
1630 if (!lba_bus) {
1631 pci_free_resource_list(&resources);
1632 return 0;
1633 }
1634
1635 max = pci_scan_child_bus(lba_bus);
1636
1637 /* This is in lieu of calling pci_assign_unassigned_resources() */
1638 if (is_pdc_pat()) {
1639 /* assign resources to un-initialized devices */
1640
1641 DBG_PAT("LBA pci_bus_size_bridges()\n");
1642 pci_bus_size_bridges(lba_bus);
1643
1644 DBG_PAT("LBA pci_bus_assign_resources()\n");
1645 pci_bus_assign_resources(lba_bus);
1646
1647 #ifdef DEBUG_LBA_PAT
1648 DBG_PAT("\nLBA PIOP resource tree\n");
1649 lba_dump_res(&lba_dev->hba.io_space, 2);
1650 DBG_PAT("\nLBA LMMIO resource tree\n");
1651 lba_dump_res(&lba_dev->hba.lmmio_space, 2);
1652 #endif
1653 }
1654
1655 /*
1656 ** Once PCI register ops has walked the bus, access to config
1657 ** space is restricted. Avoids master aborts on config cycles.
1658 ** Early LBA revs go fatal on *any* master abort.
1659 */
1660 if (cfg_ops == &elroy_cfg_ops) {
1661 lba_dev->flags |= LBA_FLAG_SKIP_PROBE;
1662 }
1663
1664 lba_next_bus = max + 1;
1665 pci_bus_add_devices(lba_bus);
1666
1667 /* Whew! Finally done! Tell services we got this one covered. */
1668 return 0;
1669 }
1670
1671 static const struct parisc_device_id lba_tbl[] __initconst = {
1672 { HPHW_BRIDGE, HVERSION_REV_ANY_ID, ELROY_HVERS, 0xa },
1673 { HPHW_BRIDGE, HVERSION_REV_ANY_ID, MERCURY_HVERS, 0xa },
1674 { HPHW_BRIDGE, HVERSION_REV_ANY_ID, QUICKSILVER_HVERS, 0xa },
1675 { 0, }
1676 };
1677
1678 static struct parisc_driver lba_driver __refdata = {
1679 .name = MODULE_NAME,
1680 .id_table = lba_tbl,
1681 .probe = lba_driver_probe,
1682 };
1683
1684 /*
1685 ** One time initialization to let the world know the LBA was found.
1686 ** Must be called exactly once before pci_init().
1687 */
lba_init(void)1688 void __init lba_init(void)
1689 {
1690 register_parisc_driver(&lba_driver);
1691 }
1692
1693 /*
1694 ** Initialize the IBASE/IMASK registers for LBA (Elroy).
1695 ** Only called from sba_iommu.c in order to route ranges (MMIO vs DMA).
1696 ** sba_iommu is responsible for locking (none needed at init time).
1697 */
lba_set_iregs(struct parisc_device * lba,u32 ibase,u32 imask)1698 void lba_set_iregs(struct parisc_device *lba, u32 ibase, u32 imask)
1699 {
1700 void __iomem * base_addr = ioremap(lba->hpa.start, 4096);
1701
1702 imask <<= 2; /* adjust for hints - 2 more bits */
1703
1704 /* Make sure we aren't trying to set bits that aren't writeable. */
1705 WARN_ON((ibase & 0x001fffff) != 0);
1706 WARN_ON((imask & 0x001fffff) != 0);
1707
1708 DBG("%s() ibase 0x%x imask 0x%x\n", __func__, ibase, imask);
1709 WRITE_REG32( imask, base_addr + LBA_IMASK);
1710 WRITE_REG32( ibase, base_addr + LBA_IBASE);
1711 iounmap(base_addr);
1712 }
1713
1714
1715 /*
1716 * The design of the Diva management card in rp34x0 machines (rp3410, rp3440)
1717 * seems rushed, so that many built-in components simply don't work.
1718 * The following quirks disable the serial AUX port and the built-in ATI RV100
1719 * Radeon 7000 graphics card which both don't have any external connectors and
1720 * thus are useless, and even worse, e.g. the AUX port occupies ttyS0 and as
1721 * such makes those machines the only PARISC machines on which we can't use
1722 * ttyS0 as boot console.
1723 */
quirk_diva_ati_card(struct pci_dev * dev)1724 static void quirk_diva_ati_card(struct pci_dev *dev)
1725 {
1726 if (dev->subsystem_vendor != PCI_VENDOR_ID_HP ||
1727 dev->subsystem_device != 0x1292)
1728 return;
1729
1730 dev_info(&dev->dev, "Hiding Diva built-in ATI card");
1731 dev->device = 0;
1732 }
1733 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, PCI_DEVICE_ID_ATI_RADEON_QY,
1734 quirk_diva_ati_card);
1735
quirk_diva_aux_disable(struct pci_dev * dev)1736 static void quirk_diva_aux_disable(struct pci_dev *dev)
1737 {
1738 if (dev->subsystem_vendor != PCI_VENDOR_ID_HP ||
1739 dev->subsystem_device != 0x1291)
1740 return;
1741
1742 dev_info(&dev->dev, "Hiding Diva built-in AUX serial device");
1743 dev->device = 0;
1744 }
1745 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA_AUX,
1746 quirk_diva_aux_disable);
1747
quirk_tosca_aux_disable(struct pci_dev * dev)1748 static void quirk_tosca_aux_disable(struct pci_dev *dev)
1749 {
1750 if (dev->subsystem_vendor != PCI_VENDOR_ID_HP ||
1751 dev->subsystem_device != 0x104a)
1752 return;
1753
1754 dev_info(&dev->dev, "Hiding Tosca secondary built-in AUX serial device");
1755 dev->device = 0;
1756 }
1757 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_DIVA,
1758 quirk_tosca_aux_disable);
1759