1# SPDX-License-Identifier: GPL-2.0-only
2#
3# Freescale device configuration
4#
5
6config NET_VENDOR_FREESCALE
7	bool "Freescale devices"
8	default y
9	depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
10		   M523x || M527x || M5272 || M528x || M520x || M532x || \
11		   ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \
12		   ARCH_LAYERSCAPE || ARCH_S32 || COMPILE_TEST
13	help
14	  If you have a network (Ethernet) card belonging to this class, say Y.
15
16	  Note that the answer to this question doesn't directly affect the
17	  kernel: saying N will just cause the configurator to skip all
18	  the questions about Freescale devices. If you say Y, you will be
19	  asked for your specific card in the following questions.
20
21if NET_VENDOR_FREESCALE
22
23config FEC
24	tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
25	depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
26		   ARCH_MXC || ARCH_S32 || SOC_IMX28 || COMPILE_TEST)
27	default ARCH_MXC || SOC_IMX28 if ARM
28	depends on PTP_1588_CLOCK_OPTIONAL
29	select CRC32
30	select PHYLIB
31	select PAGE_POOL
32	imply NET_SELFTESTS
33	help
34	  Say Y here if you want to use the built-in 10/100 Fast ethernet
35	  controller on some Motorola ColdFire and Freescale i.MX/S32 processors.
36
37config FEC_MPC52xx
38	tristate "FEC MPC52xx driver"
39	depends on PPC_MPC52xx && PPC_BESTCOMM
40	select CRC32
41	select PHYLIB
42	select PPC_BESTCOMM_FEC
43	help
44	  This option enables support for the MPC5200's on-chip
45	  Fast Ethernet Controller
46	  If compiled as module, it will be called fec_mpc52xx.
47
48config FEC_MPC52xx_MDIO
49	bool "FEC MPC52xx MDIO bus driver"
50	depends on FEC_MPC52xx
51	default y
52	help
53	  The MPC5200's FEC can connect to the Ethernet either with
54	  an external MII PHY chip or 10 Mbps 7-wire interface
55	  (Motorola? industry standard).
56	  If your board uses an external PHY connected to FEC, enable this.
57	  If not sure, enable.
58	  If compiled as module, it will be called fec_mpc52xx_phy.
59
60source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
61source "drivers/net/ethernet/freescale/fman/Kconfig"
62
63config FSL_PQ_MDIO
64	tristate "Freescale PQ MDIO"
65	select PHYLIB
66	help
67	  This driver supports the MDIO bus used by the gianfar and UCC drivers.
68
69config FSL_XGMAC_MDIO
70	tristate "Freescale XGMAC MDIO"
71	select PHYLIB
72	depends on OF
73	select OF_MDIO
74	help
75	  This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
76	  on the FMan mEMAC (which supports both Clauses 22 and 45)
77
78config UCC_GETH
79	tristate "Freescale QE Gigabit Ethernet"
80	depends on QUICC_ENGINE && PPC32
81	select FSL_PQ_MDIO
82	select PHYLIB
83	select FIXED_PHY
84	help
85	  This driver supports the Gigabit Ethernet mode of the QUICC Engine,
86	  which is available on some Freescale SOCs.
87
88config UGETH_TX_ON_DEMAND
89	bool "Transmit on Demand support"
90	depends on UCC_GETH
91
92config GIANFAR
93	tristate "Gianfar Ethernet"
94	depends on HAS_DMA
95	select FSL_PQ_MDIO
96	select PHYLIB
97	select FIXED_PHY
98	select CRC32
99	help
100	  This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
101	  and MPC86xx family of chips, the eTSEC on LS1021A and the FEC
102	  on the 8540.
103
104source "drivers/net/ethernet/freescale/dpaa/Kconfig"
105source "drivers/net/ethernet/freescale/dpaa2/Kconfig"
106source "drivers/net/ethernet/freescale/enetc/Kconfig"
107
108endif # NET_VENDOR_FREESCALE
109