1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 Conexant cx24120/cx24118 - DVBS/S2 Satellite demod/tuner driver
4
5 Copyright (C) 2008 Patrick Boettcher <pb@linuxtv.org>
6 Copyright (C) 2009 Sergey Tyurin <forum.free-x.de>
7 Updated 2012 by Jannis Achstetter <jannis_achstetter@web.de>
8 Copyright (C) 2015 Jemma Denson <jdenson@gmail.com>
9 April 2015
10 Refactored & simplified driver
11 Updated to work with delivery system supplied by DVBv5
12 Add frequency, fec & pilot to get_frontend
13
14 Cards supported: Technisat Skystar S2
15
16 */
17
18 #include <linux/slab.h>
19 #include <linux/kernel.h>
20 #include <linux/module.h>
21 #include <linux/moduleparam.h>
22 #include <linux/init.h>
23 #include <linux/firmware.h>
24 #include <media/dvb_frontend.h>
25 #include "cx24120.h"
26
27 #define CX24120_SEARCH_RANGE_KHZ 5000
28 #define CX24120_FIRMWARE "dvb-fe-cx24120-1.20.58.2.fw"
29
30 /* cx24120 i2c registers */
31 #define CX24120_REG_CMD_START 0x00 /* write cmd_id */
32 #define CX24120_REG_CMD_ARGS 0x01 /* write command arguments */
33 #define CX24120_REG_CMD_END 0x1f /* write 0x01 for end */
34
35 #define CX24120_REG_MAILBOX 0x33
36 #define CX24120_REG_FREQ3 0x34 /* frequency */
37 #define CX24120_REG_FREQ2 0x35
38 #define CX24120_REG_FREQ1 0x36
39
40 #define CX24120_REG_FECMODE 0x39 /* FEC status */
41 #define CX24120_REG_STATUS 0x3a /* Tuner status */
42 #define CX24120_REG_SIGSTR_H 0x3a /* Signal strength high */
43 #define CX24120_REG_SIGSTR_L 0x3b /* Signal strength low byte */
44 #define CX24120_REG_QUALITY_H 0x40 /* SNR high byte */
45 #define CX24120_REG_QUALITY_L 0x41 /* SNR low byte */
46
47 #define CX24120_REG_BER_HH 0x47 /* BER high byte of high word */
48 #define CX24120_REG_BER_HL 0x48 /* BER low byte of high word */
49 #define CX24120_REG_BER_LH 0x49 /* BER high byte of low word */
50 #define CX24120_REG_BER_LL 0x4a /* BER low byte of low word */
51
52 #define CX24120_REG_UCB_H 0x50 /* UCB high byte */
53 #define CX24120_REG_UCB_L 0x51 /* UCB low byte */
54
55 #define CX24120_REG_CLKDIV 0xe6
56 #define CX24120_REG_RATEDIV 0xf0
57
58 #define CX24120_REG_REVISION 0xff /* Chip revision (ro) */
59
60 /* Command messages */
61 enum command_message_id {
62 CMD_VCO_SET = 0x10, /* cmd.len = 12; */
63 CMD_TUNEREQUEST = 0x11, /* cmd.len = 15; */
64
65 CMD_MPEG_ONOFF = 0x13, /* cmd.len = 4; */
66 CMD_MPEG_INIT = 0x14, /* cmd.len = 7; */
67 CMD_BANDWIDTH = 0x15, /* cmd.len = 12; */
68 CMD_CLOCK_READ = 0x16, /* read clock */
69 CMD_CLOCK_SET = 0x17, /* cmd.len = 10; */
70
71 CMD_DISEQC_MSG1 = 0x20, /* cmd.len = 11; */
72 CMD_DISEQC_MSG2 = 0x21, /* cmd.len = d->msg_len + 6; */
73 CMD_SETVOLTAGE = 0x22, /* cmd.len = 2; */
74 CMD_SETTONE = 0x23, /* cmd.len = 4; */
75 CMD_DISEQC_BURST = 0x24, /* cmd.len not used !!! */
76
77 CMD_READ_SNR = 0x1a, /* Read signal strength */
78 CMD_START_TUNER = 0x1b, /* ??? */
79
80 CMD_FWVERSION = 0x35,
81
82 CMD_BER_CTRL = 0x3c, /* cmd.len = 0x03; */
83 };
84
85 #define CX24120_MAX_CMD_LEN 30
86
87 /* pilot mask */
88 #define CX24120_PILOT_OFF 0x00
89 #define CX24120_PILOT_ON 0x40
90 #define CX24120_PILOT_AUTO 0x80
91
92 /* signal status */
93 #define CX24120_HAS_SIGNAL 0x01
94 #define CX24120_HAS_CARRIER 0x02
95 #define CX24120_HAS_VITERBI 0x04
96 #define CX24120_HAS_LOCK 0x08
97 #define CX24120_HAS_UNK1 0x10
98 #define CX24120_HAS_UNK2 0x20
99 #define CX24120_STATUS_MASK 0x0f
100 #define CX24120_SIGNAL_MASK 0xc0
101
102 /* ber window */
103 #define CX24120_BER_WINDOW 16
104 #define CX24120_BER_WSIZE ((1 << CX24120_BER_WINDOW) * 208 * 8)
105
106 #define info(args...) pr_info("cx24120: " args)
107 #define err(args...) pr_err("cx24120: ### ERROR: " args)
108
109 /* The Demod/Tuner can't easily provide these, we cache them */
110 struct cx24120_tuning {
111 u32 frequency;
112 u32 symbol_rate;
113 enum fe_spectral_inversion inversion;
114 enum fe_code_rate fec;
115
116 enum fe_delivery_system delsys;
117 enum fe_modulation modulation;
118 enum fe_pilot pilot;
119
120 /* Demod values */
121 u8 fec_val;
122 u8 fec_mask;
123 u8 clkdiv;
124 u8 ratediv;
125 u8 inversion_val;
126 u8 pilot_val;
127 };
128
129 /* Private state */
130 struct cx24120_state {
131 struct i2c_adapter *i2c;
132 const struct cx24120_config *config;
133 struct dvb_frontend frontend;
134
135 u8 cold_init;
136 u8 mpeg_enabled;
137 u8 need_clock_set;
138
139 /* current and next tuning parameters */
140 struct cx24120_tuning dcur;
141 struct cx24120_tuning dnxt;
142
143 enum fe_status fe_status;
144
145 /* dvbv5 stats calculations */
146 u32 bitrate;
147 u32 berw_usecs;
148 u32 ber_prev;
149 u32 ucb_offset;
150 unsigned long ber_jiffies_stats;
151 unsigned long per_jiffies_stats;
152 };
153
154 /* Command message to firmware */
155 struct cx24120_cmd {
156 u8 id;
157 u8 len;
158 u8 arg[CX24120_MAX_CMD_LEN];
159 };
160
161 /* Read single register */
cx24120_readreg(struct cx24120_state * state,u8 reg)162 static int cx24120_readreg(struct cx24120_state *state, u8 reg)
163 {
164 int ret;
165 u8 buf = 0;
166 struct i2c_msg msg[] = {
167 {
168 .addr = state->config->i2c_addr,
169 .flags = 0,
170 .len = 1,
171 .buf = ®
172 }, {
173 .addr = state->config->i2c_addr,
174 .flags = I2C_M_RD,
175 .len = 1,
176 .buf = &buf
177 }
178 };
179
180 ret = i2c_transfer(state->i2c, msg, 2);
181 if (ret != 2) {
182 err("Read error: reg=0x%02x, ret=%i)\n", reg, ret);
183 return ret;
184 }
185
186 dev_dbg(&state->i2c->dev, "reg=0x%02x; data=0x%02x\n", reg, buf);
187
188 return buf;
189 }
190
191 /* Write single register */
cx24120_writereg(struct cx24120_state * state,u8 reg,u8 data)192 static int cx24120_writereg(struct cx24120_state *state, u8 reg, u8 data)
193 {
194 u8 buf[] = { reg, data };
195 struct i2c_msg msg = {
196 .addr = state->config->i2c_addr,
197 .flags = 0,
198 .buf = buf,
199 .len = 2
200 };
201 int ret;
202
203 ret = i2c_transfer(state->i2c, &msg, 1);
204 if (ret != 1) {
205 err("Write error: i2c_write error(err == %i, 0x%02x: 0x%02x)\n",
206 ret, reg, data);
207 return ret;
208 }
209
210 dev_dbg(&state->i2c->dev, "reg=0x%02x; data=0x%02x\n", reg, data);
211
212 return 0;
213 }
214
215 /* Write multiple registers in chunks of i2c_wr_max-sized buffers */
cx24120_writeregs(struct cx24120_state * state,u8 reg,const u8 * values,u16 len,u8 incr)216 static int cx24120_writeregs(struct cx24120_state *state,
217 u8 reg, const u8 *values, u16 len, u8 incr)
218 {
219 int ret;
220 u16 max = state->config->i2c_wr_max > 0 ?
221 state->config->i2c_wr_max :
222 len;
223
224 struct i2c_msg msg = {
225 .addr = state->config->i2c_addr,
226 .flags = 0,
227 };
228
229 msg.buf = kmalloc(max + 1, GFP_KERNEL);
230 if (!msg.buf)
231 return -ENOMEM;
232
233 while (len) {
234 msg.buf[0] = reg;
235 msg.len = len > max ? max : len;
236 memcpy(&msg.buf[1], values, msg.len);
237
238 len -= msg.len; /* data length revers counter */
239 values += msg.len; /* incr data pointer */
240
241 if (incr)
242 reg += msg.len;
243 msg.len++; /* don't forget the addr byte */
244
245 ret = i2c_transfer(state->i2c, &msg, 1);
246 if (ret != 1) {
247 err("i2c_write error(err == %i, 0x%02x)\n", ret, reg);
248 goto out;
249 }
250
251 dev_dbg(&state->i2c->dev, "reg=0x%02x; data=%*ph\n",
252 reg, msg.len - 1, msg.buf + 1);
253 }
254
255 ret = 0;
256
257 out:
258 kfree(msg.buf);
259 return ret;
260 }
261
262 static const struct dvb_frontend_ops cx24120_ops;
263
cx24120_attach(const struct cx24120_config * config,struct i2c_adapter * i2c)264 struct dvb_frontend *cx24120_attach(const struct cx24120_config *config,
265 struct i2c_adapter *i2c)
266 {
267 struct cx24120_state *state;
268 int demod_rev;
269
270 info("Conexant cx24120/cx24118 - DVBS/S2 Satellite demod/tuner\n");
271 state = kzalloc(sizeof(*state), GFP_KERNEL);
272 if (!state) {
273 err("Unable to allocate memory for cx24120_state\n");
274 goto error;
275 }
276
277 /* setup the state */
278 state->config = config;
279 state->i2c = i2c;
280
281 /* check if the demod is present and has proper type */
282 demod_rev = cx24120_readreg(state, CX24120_REG_REVISION);
283 switch (demod_rev) {
284 case 0x07:
285 info("Demod cx24120 rev. 0x07 detected.\n");
286 break;
287 case 0x05:
288 info("Demod cx24120 rev. 0x05 detected.\n");
289 break;
290 default:
291 err("Unsupported demod revision: 0x%x detected.\n", demod_rev);
292 goto error;
293 }
294
295 /* create dvb_frontend */
296 state->cold_init = 0;
297 memcpy(&state->frontend.ops, &cx24120_ops,
298 sizeof(struct dvb_frontend_ops));
299 state->frontend.demodulator_priv = state;
300
301 info("Conexant cx24120/cx24118 attached.\n");
302 return &state->frontend;
303
304 error:
305 kfree(state);
306 return NULL;
307 }
308 EXPORT_SYMBOL(cx24120_attach);
309
cx24120_test_rom(struct cx24120_state * state)310 static int cx24120_test_rom(struct cx24120_state *state)
311 {
312 int err, ret;
313
314 err = cx24120_readreg(state, 0xfd);
315 if (err & 4) {
316 ret = cx24120_readreg(state, 0xdf) & 0xfe;
317 err = cx24120_writereg(state, 0xdf, ret);
318 }
319 return err;
320 }
321
cx24120_read_snr(struct dvb_frontend * fe,u16 * snr)322 static int cx24120_read_snr(struct dvb_frontend *fe, u16 *snr)
323 {
324 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
325
326 if (c->cnr.stat[0].scale != FE_SCALE_DECIBEL)
327 *snr = 0;
328 else
329 *snr = div_s64(c->cnr.stat[0].svalue, 100);
330
331 return 0;
332 }
333
cx24120_read_ber(struct dvb_frontend * fe,u32 * ber)334 static int cx24120_read_ber(struct dvb_frontend *fe, u32 *ber)
335 {
336 struct cx24120_state *state = fe->demodulator_priv;
337 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
338
339 if (c->post_bit_error.stat[0].scale != FE_SCALE_COUNTER) {
340 *ber = 0;
341 return 0;
342 }
343
344 *ber = c->post_bit_error.stat[0].uvalue - state->ber_prev;
345 state->ber_prev = c->post_bit_error.stat[0].uvalue;
346
347 return 0;
348 }
349
350 static int cx24120_msg_mpeg_output_global_config(struct cx24120_state *state,
351 u8 flag);
352
353 /* Check if we're running a command that needs to disable mpeg out */
cx24120_check_cmd(struct cx24120_state * state,u8 id)354 static void cx24120_check_cmd(struct cx24120_state *state, u8 id)
355 {
356 switch (id) {
357 case CMD_TUNEREQUEST:
358 case CMD_CLOCK_READ:
359 case CMD_DISEQC_MSG1:
360 case CMD_DISEQC_MSG2:
361 case CMD_SETVOLTAGE:
362 case CMD_SETTONE:
363 case CMD_DISEQC_BURST:
364 cx24120_msg_mpeg_output_global_config(state, 0);
365 /* Old driver would do a msleep(100) here */
366 return;
367 default:
368 return;
369 }
370 }
371
372 /* Send a message to the firmware */
cx24120_message_send(struct cx24120_state * state,struct cx24120_cmd * cmd)373 static int cx24120_message_send(struct cx24120_state *state,
374 struct cx24120_cmd *cmd)
375 {
376 int ficus;
377
378 if (state->mpeg_enabled) {
379 /* Disable mpeg out on certain commands */
380 cx24120_check_cmd(state, cmd->id);
381 }
382
383 cx24120_writereg(state, CX24120_REG_CMD_START, cmd->id);
384 cx24120_writeregs(state, CX24120_REG_CMD_ARGS, &cmd->arg[0],
385 cmd->len, 1);
386 cx24120_writereg(state, CX24120_REG_CMD_END, 0x01);
387
388 ficus = 1000;
389 while (cx24120_readreg(state, CX24120_REG_CMD_END)) {
390 msleep(20);
391 ficus -= 20;
392 if (ficus == 0) {
393 err("Error sending message to firmware\n");
394 return -EREMOTEIO;
395 }
396 }
397 dev_dbg(&state->i2c->dev, "sent message 0x%02x\n", cmd->id);
398
399 return 0;
400 }
401
402 /* Send a message and fill arg[] with the results */
cx24120_message_sendrcv(struct cx24120_state * state,struct cx24120_cmd * cmd,u8 numreg)403 static int cx24120_message_sendrcv(struct cx24120_state *state,
404 struct cx24120_cmd *cmd, u8 numreg)
405 {
406 int ret, i;
407
408 if (numreg > CX24120_MAX_CMD_LEN) {
409 err("Too many registers to read. cmd->reg = %d", numreg);
410 return -EREMOTEIO;
411 }
412
413 ret = cx24120_message_send(state, cmd);
414 if (ret != 0)
415 return ret;
416
417 if (!numreg)
418 return 0;
419
420 /* Read numreg registers starting from register cmd->len */
421 for (i = 0; i < numreg; i++)
422 cmd->arg[i] = cx24120_readreg(state, (cmd->len + i + 1));
423
424 return 0;
425 }
426
cx24120_read_signal_strength(struct dvb_frontend * fe,u16 * signal_strength)427 static int cx24120_read_signal_strength(struct dvb_frontend *fe,
428 u16 *signal_strength)
429 {
430 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
431
432 if (c->strength.stat[0].scale != FE_SCALE_RELATIVE)
433 *signal_strength = 0;
434 else
435 *signal_strength = c->strength.stat[0].uvalue;
436
437 return 0;
438 }
439
cx24120_msg_mpeg_output_global_config(struct cx24120_state * state,u8 enable)440 static int cx24120_msg_mpeg_output_global_config(struct cx24120_state *state,
441 u8 enable)
442 {
443 struct cx24120_cmd cmd;
444 int ret;
445
446 cmd.id = CMD_MPEG_ONOFF;
447 cmd.len = 4;
448 cmd.arg[0] = 0x01;
449 cmd.arg[1] = 0x00;
450 cmd.arg[2] = enable ? 0 : (u8)(-1);
451 cmd.arg[3] = 0x01;
452
453 ret = cx24120_message_send(state, &cmd);
454 if (ret != 0) {
455 dev_dbg(&state->i2c->dev, "failed to %s MPEG output\n",
456 enable ? "enable" : "disable");
457 return ret;
458 }
459
460 state->mpeg_enabled = enable;
461 dev_dbg(&state->i2c->dev, "MPEG output %s\n",
462 enable ? "enabled" : "disabled");
463
464 return 0;
465 }
466
cx24120_msg_mpeg_output_config(struct cx24120_state * state,u8 seq)467 static int cx24120_msg_mpeg_output_config(struct cx24120_state *state, u8 seq)
468 {
469 struct cx24120_cmd cmd;
470 struct cx24120_initial_mpeg_config i =
471 state->config->initial_mpeg_config;
472
473 cmd.id = CMD_MPEG_INIT;
474 cmd.len = 7;
475 cmd.arg[0] = seq; /* sequental number - can be 0,1,2 */
476 cmd.arg[1] = ((i.x1 & 0x01) << 1) | ((i.x1 >> 1) & 0x01);
477 cmd.arg[2] = 0x05;
478 cmd.arg[3] = 0x02;
479 cmd.arg[4] = ((i.x2 >> 1) & 0x01);
480 cmd.arg[5] = (i.x2 & 0xf0) | (i.x3 & 0x0f);
481 cmd.arg[6] = 0x10;
482
483 return cx24120_message_send(state, &cmd);
484 }
485
cx24120_diseqc_send_burst(struct dvb_frontend * fe,enum fe_sec_mini_cmd burst)486 static int cx24120_diseqc_send_burst(struct dvb_frontend *fe,
487 enum fe_sec_mini_cmd burst)
488 {
489 struct cx24120_state *state = fe->demodulator_priv;
490 struct cx24120_cmd cmd;
491
492 dev_dbg(&state->i2c->dev, "\n");
493
494 /*
495 * Yes, cmd.len is set to zero. The old driver
496 * didn't specify any len, but also had a
497 * memset 0 before every use of the cmd struct
498 * which would have set it to zero.
499 * This quite probably needs looking into.
500 */
501 cmd.id = CMD_DISEQC_BURST;
502 cmd.len = 0;
503 cmd.arg[0] = 0x00;
504 cmd.arg[1] = (burst == SEC_MINI_B) ? 0x01 : 0x00;
505
506 return cx24120_message_send(state, &cmd);
507 }
508
cx24120_set_tone(struct dvb_frontend * fe,enum fe_sec_tone_mode tone)509 static int cx24120_set_tone(struct dvb_frontend *fe, enum fe_sec_tone_mode tone)
510 {
511 struct cx24120_state *state = fe->demodulator_priv;
512 struct cx24120_cmd cmd;
513
514 dev_dbg(&state->i2c->dev, "(%d)\n", tone);
515
516 if ((tone != SEC_TONE_ON) && (tone != SEC_TONE_OFF)) {
517 err("Invalid tone=%d\n", tone);
518 return -EINVAL;
519 }
520
521 cmd.id = CMD_SETTONE;
522 cmd.len = 4;
523 cmd.arg[0] = 0x00;
524 cmd.arg[1] = 0x00;
525 cmd.arg[2] = 0x00;
526 cmd.arg[3] = (tone == SEC_TONE_ON) ? 0x01 : 0x00;
527
528 return cx24120_message_send(state, &cmd);
529 }
530
cx24120_set_voltage(struct dvb_frontend * fe,enum fe_sec_voltage voltage)531 static int cx24120_set_voltage(struct dvb_frontend *fe,
532 enum fe_sec_voltage voltage)
533 {
534 struct cx24120_state *state = fe->demodulator_priv;
535 struct cx24120_cmd cmd;
536
537 dev_dbg(&state->i2c->dev, "(%d)\n", voltage);
538
539 cmd.id = CMD_SETVOLTAGE;
540 cmd.len = 2;
541 cmd.arg[0] = 0x00;
542 cmd.arg[1] = (voltage == SEC_VOLTAGE_18) ? 0x01 : 0x00;
543
544 return cx24120_message_send(state, &cmd);
545 }
546
cx24120_send_diseqc_msg(struct dvb_frontend * fe,struct dvb_diseqc_master_cmd * d)547 static int cx24120_send_diseqc_msg(struct dvb_frontend *fe,
548 struct dvb_diseqc_master_cmd *d)
549 {
550 struct cx24120_state *state = fe->demodulator_priv;
551 struct cx24120_cmd cmd;
552 int back_count;
553
554 dev_dbg(&state->i2c->dev, "\n");
555
556 cmd.id = CMD_DISEQC_MSG1;
557 cmd.len = 11;
558 cmd.arg[0] = 0x00;
559 cmd.arg[1] = 0x00;
560 cmd.arg[2] = 0x03;
561 cmd.arg[3] = 0x16;
562 cmd.arg[4] = 0x28;
563 cmd.arg[5] = 0x01;
564 cmd.arg[6] = 0x01;
565 cmd.arg[7] = 0x14;
566 cmd.arg[8] = 0x19;
567 cmd.arg[9] = 0x14;
568 cmd.arg[10] = 0x1e;
569
570 if (cx24120_message_send(state, &cmd)) {
571 err("send 1st message(0x%x) failed\n", cmd.id);
572 return -EREMOTEIO;
573 }
574
575 cmd.id = CMD_DISEQC_MSG2;
576 cmd.len = d->msg_len + 6;
577 cmd.arg[0] = 0x00;
578 cmd.arg[1] = 0x01;
579 cmd.arg[2] = 0x02;
580 cmd.arg[3] = 0x00;
581 cmd.arg[4] = 0x00;
582 cmd.arg[5] = d->msg_len;
583
584 memcpy(&cmd.arg[6], &d->msg, d->msg_len);
585
586 if (cx24120_message_send(state, &cmd)) {
587 err("send 2nd message(0x%x) failed\n", cmd.id);
588 return -EREMOTEIO;
589 }
590
591 back_count = 500;
592 do {
593 if (!(cx24120_readreg(state, 0x93) & 0x01)) {
594 dev_dbg(&state->i2c->dev, "diseqc sequence sent\n");
595 return 0;
596 }
597 msleep(20);
598 back_count -= 20;
599 } while (back_count);
600
601 err("Too long waiting for diseqc.\n");
602 return -ETIMEDOUT;
603 }
604
cx24120_get_stats(struct cx24120_state * state)605 static void cx24120_get_stats(struct cx24120_state *state)
606 {
607 struct dvb_frontend *fe = &state->frontend;
608 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
609 struct cx24120_cmd cmd;
610 int ret, cnr, msecs;
611 u16 sig, ucb;
612 u32 ber;
613
614 dev_dbg(&state->i2c->dev, "\n");
615
616 /* signal strength */
617 if (state->fe_status & FE_HAS_SIGNAL) {
618 cmd.id = CMD_READ_SNR;
619 cmd.len = 1;
620 cmd.arg[0] = 0x00;
621
622 ret = cx24120_message_send(state, &cmd);
623 if (ret != 0) {
624 err("error reading signal strength\n");
625 return;
626 }
627
628 /* raw */
629 sig = cx24120_readreg(state, CX24120_REG_SIGSTR_H) >> 6;
630 sig = sig << 8;
631 sig |= cx24120_readreg(state, CX24120_REG_SIGSTR_L);
632 dev_dbg(&state->i2c->dev,
633 "signal strength from firmware = 0x%x\n", sig);
634
635 /* cooked */
636 sig = -100 * sig + 94324;
637
638 c->strength.stat[0].scale = FE_SCALE_RELATIVE;
639 c->strength.stat[0].uvalue = sig;
640 } else {
641 c->strength.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
642 }
643
644 /* CNR */
645 if (state->fe_status & FE_HAS_VITERBI) {
646 cnr = cx24120_readreg(state, CX24120_REG_QUALITY_H) << 8;
647 cnr |= cx24120_readreg(state, CX24120_REG_QUALITY_L);
648 dev_dbg(&state->i2c->dev, "read SNR index = %d\n", cnr);
649
650 /* guessed - seems about right */
651 cnr = cnr * 100;
652
653 c->cnr.stat[0].scale = FE_SCALE_DECIBEL;
654 c->cnr.stat[0].svalue = cnr;
655 } else {
656 c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
657 }
658
659 /* BER & UCB require lock */
660 if (!(state->fe_status & FE_HAS_LOCK)) {
661 c->post_bit_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
662 c->post_bit_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
663 c->block_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
664 c->block_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
665 return;
666 }
667
668 /* BER */
669 if (time_after(jiffies, state->ber_jiffies_stats)) {
670 msecs = (state->berw_usecs + 500) / 1000;
671 state->ber_jiffies_stats = jiffies + msecs_to_jiffies(msecs);
672
673 ber = cx24120_readreg(state, CX24120_REG_BER_HH) << 24;
674 ber |= cx24120_readreg(state, CX24120_REG_BER_HL) << 16;
675 ber |= cx24120_readreg(state, CX24120_REG_BER_LH) << 8;
676 ber |= cx24120_readreg(state, CX24120_REG_BER_LL);
677 dev_dbg(&state->i2c->dev, "read BER index = %d\n", ber);
678
679 c->post_bit_error.stat[0].scale = FE_SCALE_COUNTER;
680 c->post_bit_error.stat[0].uvalue += ber;
681
682 c->post_bit_count.stat[0].scale = FE_SCALE_COUNTER;
683 c->post_bit_count.stat[0].uvalue += CX24120_BER_WSIZE;
684 }
685
686 /* UCB */
687 if (time_after(jiffies, state->per_jiffies_stats)) {
688 state->per_jiffies_stats = jiffies + msecs_to_jiffies(1000);
689
690 ucb = cx24120_readreg(state, CX24120_REG_UCB_H) << 8;
691 ucb |= cx24120_readreg(state, CX24120_REG_UCB_L);
692 dev_dbg(&state->i2c->dev, "ucblocks = %d\n", ucb);
693
694 /* handle reset */
695 if (ucb < state->ucb_offset)
696 state->ucb_offset = c->block_error.stat[0].uvalue;
697
698 c->block_error.stat[0].scale = FE_SCALE_COUNTER;
699 c->block_error.stat[0].uvalue = ucb + state->ucb_offset;
700
701 c->block_count.stat[0].scale = FE_SCALE_COUNTER;
702 c->block_count.stat[0].uvalue += state->bitrate / 8 / 208;
703 }
704 }
705
706 static void cx24120_set_clock_ratios(struct dvb_frontend *fe);
707
708 /* Read current tuning status */
cx24120_read_status(struct dvb_frontend * fe,enum fe_status * status)709 static int cx24120_read_status(struct dvb_frontend *fe, enum fe_status *status)
710 {
711 struct cx24120_state *state = fe->demodulator_priv;
712 int lock;
713
714 lock = cx24120_readreg(state, CX24120_REG_STATUS);
715
716 dev_dbg(&state->i2c->dev, "status = 0x%02x\n", lock);
717
718 *status = 0;
719
720 if (lock & CX24120_HAS_SIGNAL)
721 *status = FE_HAS_SIGNAL;
722 if (lock & CX24120_HAS_CARRIER)
723 *status |= FE_HAS_CARRIER;
724 if (lock & CX24120_HAS_VITERBI)
725 *status |= FE_HAS_VITERBI | FE_HAS_SYNC;
726 if (lock & CX24120_HAS_LOCK)
727 *status |= FE_HAS_LOCK;
728
729 /*
730 * TODO: is FE_HAS_SYNC in the right place?
731 * Other cx241xx drivers have this slightly
732 * different
733 */
734
735 state->fe_status = *status;
736 cx24120_get_stats(state);
737
738 /* Set the clock once tuned in */
739 if (state->need_clock_set && *status & FE_HAS_LOCK) {
740 /* Set clock ratios */
741 cx24120_set_clock_ratios(fe);
742
743 /* Old driver would do a msleep(200) here */
744
745 /* Renable mpeg output */
746 if (!state->mpeg_enabled)
747 cx24120_msg_mpeg_output_global_config(state, 1);
748
749 state->need_clock_set = 0;
750 }
751
752 return 0;
753 }
754
755 /*
756 * FEC & modulation lookup table
757 * Used for decoding the REG_FECMODE register
758 * once tuned in.
759 */
760 struct cx24120_modfec {
761 enum fe_delivery_system delsys;
762 enum fe_modulation mod;
763 enum fe_code_rate fec;
764 u8 val;
765 };
766
767 static const struct cx24120_modfec modfec_lookup_table[] = {
768 /*delsys mod fec val */
769 { SYS_DVBS, QPSK, FEC_1_2, 0x01 },
770 { SYS_DVBS, QPSK, FEC_2_3, 0x02 },
771 { SYS_DVBS, QPSK, FEC_3_4, 0x03 },
772 { SYS_DVBS, QPSK, FEC_4_5, 0x04 },
773 { SYS_DVBS, QPSK, FEC_5_6, 0x05 },
774 { SYS_DVBS, QPSK, FEC_6_7, 0x06 },
775 { SYS_DVBS, QPSK, FEC_7_8, 0x07 },
776
777 { SYS_DVBS2, QPSK, FEC_1_2, 0x04 },
778 { SYS_DVBS2, QPSK, FEC_3_5, 0x05 },
779 { SYS_DVBS2, QPSK, FEC_2_3, 0x06 },
780 { SYS_DVBS2, QPSK, FEC_3_4, 0x07 },
781 { SYS_DVBS2, QPSK, FEC_4_5, 0x08 },
782 { SYS_DVBS2, QPSK, FEC_5_6, 0x09 },
783 { SYS_DVBS2, QPSK, FEC_8_9, 0x0a },
784 { SYS_DVBS2, QPSK, FEC_9_10, 0x0b },
785
786 { SYS_DVBS2, PSK_8, FEC_3_5, 0x0c },
787 { SYS_DVBS2, PSK_8, FEC_2_3, 0x0d },
788 { SYS_DVBS2, PSK_8, FEC_3_4, 0x0e },
789 { SYS_DVBS2, PSK_8, FEC_5_6, 0x0f },
790 { SYS_DVBS2, PSK_8, FEC_8_9, 0x10 },
791 { SYS_DVBS2, PSK_8, FEC_9_10, 0x11 },
792 };
793
794 /* Retrieve current fec, modulation & pilot values */
cx24120_get_fec(struct dvb_frontend * fe)795 static int cx24120_get_fec(struct dvb_frontend *fe)
796 {
797 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
798 struct cx24120_state *state = fe->demodulator_priv;
799 int idx;
800 int ret;
801 int fec;
802
803 ret = cx24120_readreg(state, CX24120_REG_FECMODE);
804 fec = ret & 0x3f; /* Lower 6 bits */
805
806 dev_dbg(&state->i2c->dev, "raw fec = %d\n", fec);
807
808 for (idx = 0; idx < ARRAY_SIZE(modfec_lookup_table); idx++) {
809 if (modfec_lookup_table[idx].delsys != state->dcur.delsys)
810 continue;
811 if (modfec_lookup_table[idx].val != fec)
812 continue;
813
814 break; /* found */
815 }
816
817 if (idx >= ARRAY_SIZE(modfec_lookup_table)) {
818 dev_dbg(&state->i2c->dev, "couldn't find fec!\n");
819 return -EINVAL;
820 }
821
822 /* save values back to cache */
823 c->modulation = modfec_lookup_table[idx].mod;
824 c->fec_inner = modfec_lookup_table[idx].fec;
825 c->pilot = (ret & 0x80) ? PILOT_ON : PILOT_OFF;
826
827 dev_dbg(&state->i2c->dev, "mod(%d), fec(%d), pilot(%d)\n",
828 c->modulation, c->fec_inner, c->pilot);
829
830 return 0;
831 }
832
833 /* Calculate ber window time */
cx24120_calculate_ber_window(struct cx24120_state * state,u32 rate)834 static void cx24120_calculate_ber_window(struct cx24120_state *state, u32 rate)
835 {
836 struct dvb_frontend *fe = &state->frontend;
837 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
838 u64 tmp;
839
840 /*
841 * Calculate bitrate from rate in the clock ratios table.
842 * This isn't *exactly* right but close enough.
843 */
844 tmp = (u64)c->symbol_rate * rate;
845 do_div(tmp, 256);
846 state->bitrate = tmp;
847
848 /* usecs per ber window */
849 tmp = 1000000ULL * CX24120_BER_WSIZE;
850 do_div(tmp, state->bitrate);
851 state->berw_usecs = tmp;
852
853 dev_dbg(&state->i2c->dev, "bitrate: %u, berw_usecs: %u\n",
854 state->bitrate, state->berw_usecs);
855 }
856
857 /*
858 * Clock ratios lookup table
859 *
860 * Values obtained from much larger table in old driver
861 * which had numerous entries which would never match.
862 *
863 * There's probably some way of calculating these but I
864 * can't determine the pattern
865 */
866 struct cx24120_clock_ratios_table {
867 enum fe_delivery_system delsys;
868 enum fe_pilot pilot;
869 enum fe_modulation mod;
870 enum fe_code_rate fec;
871 u32 m_rat;
872 u32 n_rat;
873 u32 rate;
874 };
875
876 static const struct cx24120_clock_ratios_table clock_ratios_table[] = {
877 /*delsys pilot mod fec m_rat n_rat rate */
878 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_1_2, 273088, 254505, 274 },
879 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_3_5, 17272, 13395, 330 },
880 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_2_3, 24344, 16967, 367 },
881 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_3_4, 410788, 254505, 413 },
882 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_4_5, 438328, 254505, 440 },
883 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_5_6, 30464, 16967, 459 },
884 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_8_9, 487832, 254505, 490 },
885 { SYS_DVBS2, PILOT_OFF, QPSK, FEC_9_10, 493952, 254505, 496 },
886 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_3_5, 328168, 169905, 494 },
887 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_2_3, 24344, 11327, 550 },
888 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_3_4, 410788, 169905, 618 },
889 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_5_6, 30464, 11327, 688 },
890 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_8_9, 487832, 169905, 735 },
891 { SYS_DVBS2, PILOT_OFF, PSK_8, FEC_9_10, 493952, 169905, 744 },
892 { SYS_DVBS2, PILOT_ON, QPSK, FEC_1_2, 273088, 260709, 268 },
893 { SYS_DVBS2, PILOT_ON, QPSK, FEC_3_5, 328168, 260709, 322 },
894 { SYS_DVBS2, PILOT_ON, QPSK, FEC_2_3, 121720, 86903, 358 },
895 { SYS_DVBS2, PILOT_ON, QPSK, FEC_3_4, 410788, 260709, 403 },
896 { SYS_DVBS2, PILOT_ON, QPSK, FEC_4_5, 438328, 260709, 430 },
897 { SYS_DVBS2, PILOT_ON, QPSK, FEC_5_6, 152320, 86903, 448 },
898 { SYS_DVBS2, PILOT_ON, QPSK, FEC_8_9, 487832, 260709, 479 },
899 { SYS_DVBS2, PILOT_ON, QPSK, FEC_9_10, 493952, 260709, 485 },
900 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_3_5, 328168, 173853, 483 },
901 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_2_3, 121720, 57951, 537 },
902 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_3_4, 410788, 173853, 604 },
903 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_5_6, 152320, 57951, 672 },
904 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_8_9, 487832, 173853, 718 },
905 { SYS_DVBS2, PILOT_ON, PSK_8, FEC_9_10, 493952, 173853, 727 },
906 { SYS_DVBS, PILOT_OFF, QPSK, FEC_1_2, 152592, 152592, 256 },
907 { SYS_DVBS, PILOT_OFF, QPSK, FEC_2_3, 305184, 228888, 341 },
908 { SYS_DVBS, PILOT_OFF, QPSK, FEC_3_4, 457776, 305184, 384 },
909 { SYS_DVBS, PILOT_OFF, QPSK, FEC_5_6, 762960, 457776, 427 },
910 { SYS_DVBS, PILOT_OFF, QPSK, FEC_7_8, 1068144, 610368, 448 },
911 };
912
913 /* Set clock ratio from lookup table */
cx24120_set_clock_ratios(struct dvb_frontend * fe)914 static void cx24120_set_clock_ratios(struct dvb_frontend *fe)
915 {
916 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
917 struct cx24120_state *state = fe->demodulator_priv;
918 struct cx24120_cmd cmd;
919 int ret, idx;
920
921 /* Find fec, modulation, pilot */
922 ret = cx24120_get_fec(fe);
923 if (ret != 0)
924 return;
925
926 /* Find the clock ratios in the lookup table */
927 for (idx = 0; idx < ARRAY_SIZE(clock_ratios_table); idx++) {
928 if (clock_ratios_table[idx].delsys != state->dcur.delsys)
929 continue;
930 if (clock_ratios_table[idx].mod != c->modulation)
931 continue;
932 if (clock_ratios_table[idx].fec != c->fec_inner)
933 continue;
934 if (clock_ratios_table[idx].pilot != c->pilot)
935 continue;
936
937 break; /* found */
938 }
939
940 if (idx >= ARRAY_SIZE(clock_ratios_table)) {
941 info("Clock ratio not found - data reception in danger\n");
942 return;
943 }
944
945 /* Read current values? */
946 cmd.id = CMD_CLOCK_READ;
947 cmd.len = 1;
948 cmd.arg[0] = 0x00;
949 ret = cx24120_message_sendrcv(state, &cmd, 6);
950 if (ret != 0)
951 return;
952 /* in cmd[0]-[5] - result */
953
954 dev_dbg(&state->i2c->dev, "m=%d, n=%d; idx: %d m=%d, n=%d, rate=%d\n",
955 cmd.arg[2] | (cmd.arg[1] << 8) | (cmd.arg[0] << 16),
956 cmd.arg[5] | (cmd.arg[4] << 8) | (cmd.arg[3] << 16),
957 idx,
958 clock_ratios_table[idx].m_rat,
959 clock_ratios_table[idx].n_rat,
960 clock_ratios_table[idx].rate);
961
962 /* Set the clock */
963 cmd.id = CMD_CLOCK_SET;
964 cmd.len = 10;
965 cmd.arg[0] = 0;
966 cmd.arg[1] = 0x10;
967 cmd.arg[2] = (clock_ratios_table[idx].m_rat >> 16) & 0xff;
968 cmd.arg[3] = (clock_ratios_table[idx].m_rat >> 8) & 0xff;
969 cmd.arg[4] = (clock_ratios_table[idx].m_rat >> 0) & 0xff;
970 cmd.arg[5] = (clock_ratios_table[idx].n_rat >> 16) & 0xff;
971 cmd.arg[6] = (clock_ratios_table[idx].n_rat >> 8) & 0xff;
972 cmd.arg[7] = (clock_ratios_table[idx].n_rat >> 0) & 0xff;
973 cmd.arg[8] = (clock_ratios_table[idx].rate >> 8) & 0xff;
974 cmd.arg[9] = (clock_ratios_table[idx].rate >> 0) & 0xff;
975
976 cx24120_message_send(state, &cmd);
977
978 /* Calculate ber window rates for stat work */
979 cx24120_calculate_ber_window(state, clock_ratios_table[idx].rate);
980 }
981
982 /* Set inversion value */
cx24120_set_inversion(struct cx24120_state * state,enum fe_spectral_inversion inversion)983 static int cx24120_set_inversion(struct cx24120_state *state,
984 enum fe_spectral_inversion inversion)
985 {
986 dev_dbg(&state->i2c->dev, "(%d)\n", inversion);
987
988 switch (inversion) {
989 case INVERSION_OFF:
990 state->dnxt.inversion_val = 0x00;
991 break;
992 case INVERSION_ON:
993 state->dnxt.inversion_val = 0x04;
994 break;
995 case INVERSION_AUTO:
996 state->dnxt.inversion_val = 0x0c;
997 break;
998 default:
999 return -EINVAL;
1000 }
1001
1002 state->dnxt.inversion = inversion;
1003
1004 return 0;
1005 }
1006
1007 /* FEC lookup table for tuning */
1008 struct cx24120_modfec_table {
1009 enum fe_delivery_system delsys;
1010 enum fe_modulation mod;
1011 enum fe_code_rate fec;
1012 u8 val;
1013 };
1014
1015 static const struct cx24120_modfec_table modfec_table[] = {
1016 /*delsys mod fec val */
1017 { SYS_DVBS, QPSK, FEC_1_2, 0x2e },
1018 { SYS_DVBS, QPSK, FEC_2_3, 0x2f },
1019 { SYS_DVBS, QPSK, FEC_3_4, 0x30 },
1020 { SYS_DVBS, QPSK, FEC_5_6, 0x31 },
1021 { SYS_DVBS, QPSK, FEC_6_7, 0x32 },
1022 { SYS_DVBS, QPSK, FEC_7_8, 0x33 },
1023
1024 { SYS_DVBS2, QPSK, FEC_1_2, 0x04 },
1025 { SYS_DVBS2, QPSK, FEC_3_5, 0x05 },
1026 { SYS_DVBS2, QPSK, FEC_2_3, 0x06 },
1027 { SYS_DVBS2, QPSK, FEC_3_4, 0x07 },
1028 { SYS_DVBS2, QPSK, FEC_4_5, 0x08 },
1029 { SYS_DVBS2, QPSK, FEC_5_6, 0x09 },
1030 { SYS_DVBS2, QPSK, FEC_8_9, 0x0a },
1031 { SYS_DVBS2, QPSK, FEC_9_10, 0x0b },
1032
1033 { SYS_DVBS2, PSK_8, FEC_3_5, 0x0c },
1034 { SYS_DVBS2, PSK_8, FEC_2_3, 0x0d },
1035 { SYS_DVBS2, PSK_8, FEC_3_4, 0x0e },
1036 { SYS_DVBS2, PSK_8, FEC_5_6, 0x0f },
1037 { SYS_DVBS2, PSK_8, FEC_8_9, 0x10 },
1038 { SYS_DVBS2, PSK_8, FEC_9_10, 0x11 },
1039 };
1040
1041 /* Set fec_val & fec_mask values from delsys, modulation & fec */
cx24120_set_fec(struct cx24120_state * state,enum fe_modulation mod,enum fe_code_rate fec)1042 static int cx24120_set_fec(struct cx24120_state *state, enum fe_modulation mod,
1043 enum fe_code_rate fec)
1044 {
1045 int idx;
1046
1047 dev_dbg(&state->i2c->dev, "(0x%02x,0x%02x)\n", mod, fec);
1048
1049 state->dnxt.fec = fec;
1050
1051 /* Lookup fec_val from modfec table */
1052 for (idx = 0; idx < ARRAY_SIZE(modfec_table); idx++) {
1053 if (modfec_table[idx].delsys != state->dnxt.delsys)
1054 continue;
1055 if (modfec_table[idx].mod != mod)
1056 continue;
1057 if (modfec_table[idx].fec != fec)
1058 continue;
1059
1060 /* found */
1061 state->dnxt.fec_mask = 0x00;
1062 state->dnxt.fec_val = modfec_table[idx].val;
1063 return 0;
1064 }
1065
1066 if (state->dnxt.delsys == SYS_DVBS2) {
1067 /* DVBS2 auto is 0x00/0x00 */
1068 state->dnxt.fec_mask = 0x00;
1069 state->dnxt.fec_val = 0x00;
1070 } else {
1071 /* Set DVB-S to auto */
1072 state->dnxt.fec_val = 0x2e;
1073 state->dnxt.fec_mask = 0xac;
1074 }
1075
1076 return 0;
1077 }
1078
1079 /* Set pilot */
cx24120_set_pilot(struct cx24120_state * state,enum fe_pilot pilot)1080 static int cx24120_set_pilot(struct cx24120_state *state, enum fe_pilot pilot)
1081 {
1082 dev_dbg(&state->i2c->dev, "(%d)\n", pilot);
1083
1084 /* Pilot only valid in DVBS2 */
1085 if (state->dnxt.delsys != SYS_DVBS2) {
1086 state->dnxt.pilot_val = CX24120_PILOT_OFF;
1087 return 0;
1088 }
1089
1090 switch (pilot) {
1091 case PILOT_OFF:
1092 state->dnxt.pilot_val = CX24120_PILOT_OFF;
1093 break;
1094 case PILOT_ON:
1095 state->dnxt.pilot_val = CX24120_PILOT_ON;
1096 break;
1097 case PILOT_AUTO:
1098 default:
1099 state->dnxt.pilot_val = CX24120_PILOT_AUTO;
1100 }
1101
1102 return 0;
1103 }
1104
1105 /* Set symbol rate */
cx24120_set_symbolrate(struct cx24120_state * state,u32 rate)1106 static int cx24120_set_symbolrate(struct cx24120_state *state, u32 rate)
1107 {
1108 dev_dbg(&state->i2c->dev, "(%d)\n", rate);
1109
1110 state->dnxt.symbol_rate = rate;
1111
1112 /* Check symbol rate */
1113 if (rate > 31000000) {
1114 state->dnxt.clkdiv = (-(rate < 31000001) & 3) + 2;
1115 state->dnxt.ratediv = (-(rate < 31000001) & 6) + 4;
1116 } else {
1117 state->dnxt.clkdiv = 3;
1118 state->dnxt.ratediv = 6;
1119 }
1120
1121 return 0;
1122 }
1123
1124 /* Overwrite the current tuning params, we are about to tune */
cx24120_clone_params(struct dvb_frontend * fe)1125 static void cx24120_clone_params(struct dvb_frontend *fe)
1126 {
1127 struct cx24120_state *state = fe->demodulator_priv;
1128
1129 state->dcur = state->dnxt;
1130 }
1131
cx24120_set_frontend(struct dvb_frontend * fe)1132 static int cx24120_set_frontend(struct dvb_frontend *fe)
1133 {
1134 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
1135 struct cx24120_state *state = fe->demodulator_priv;
1136 struct cx24120_cmd cmd;
1137 int ret;
1138
1139 switch (c->delivery_system) {
1140 case SYS_DVBS2:
1141 dev_dbg(&state->i2c->dev, "DVB-S2\n");
1142 break;
1143 case SYS_DVBS:
1144 dev_dbg(&state->i2c->dev, "DVB-S\n");
1145 break;
1146 default:
1147 dev_dbg(&state->i2c->dev,
1148 "delivery system(%d) not supported\n",
1149 c->delivery_system);
1150 return -EINVAL;
1151 }
1152
1153 state->dnxt.delsys = c->delivery_system;
1154 state->dnxt.modulation = c->modulation;
1155 state->dnxt.frequency = c->frequency;
1156 state->dnxt.pilot = c->pilot;
1157
1158 ret = cx24120_set_inversion(state, c->inversion);
1159 if (ret != 0)
1160 return ret;
1161
1162 ret = cx24120_set_fec(state, c->modulation, c->fec_inner);
1163 if (ret != 0)
1164 return ret;
1165
1166 ret = cx24120_set_pilot(state, c->pilot);
1167 if (ret != 0)
1168 return ret;
1169
1170 ret = cx24120_set_symbolrate(state, c->symbol_rate);
1171 if (ret != 0)
1172 return ret;
1173
1174 /* discard the 'current' tuning parameters and prepare to tune */
1175 cx24120_clone_params(fe);
1176
1177 dev_dbg(&state->i2c->dev,
1178 "delsys = %d\n", state->dcur.delsys);
1179 dev_dbg(&state->i2c->dev,
1180 "modulation = %d\n", state->dcur.modulation);
1181 dev_dbg(&state->i2c->dev,
1182 "frequency = %d\n", state->dcur.frequency);
1183 dev_dbg(&state->i2c->dev,
1184 "pilot = %d (val = 0x%02x)\n",
1185 state->dcur.pilot, state->dcur.pilot_val);
1186 dev_dbg(&state->i2c->dev,
1187 "symbol_rate = %d (clkdiv/ratediv = 0x%02x/0x%02x)\n",
1188 state->dcur.symbol_rate,
1189 state->dcur.clkdiv, state->dcur.ratediv);
1190 dev_dbg(&state->i2c->dev,
1191 "FEC = %d (mask/val = 0x%02x/0x%02x)\n",
1192 state->dcur.fec, state->dcur.fec_mask, state->dcur.fec_val);
1193 dev_dbg(&state->i2c->dev,
1194 "Inversion = %d (val = 0x%02x)\n",
1195 state->dcur.inversion, state->dcur.inversion_val);
1196
1197 /* Flag that clock needs to be set after tune */
1198 state->need_clock_set = 1;
1199
1200 /* Tune in */
1201 cmd.id = CMD_TUNEREQUEST;
1202 cmd.len = 15;
1203 cmd.arg[0] = 0;
1204 cmd.arg[1] = (state->dcur.frequency & 0xff0000) >> 16;
1205 cmd.arg[2] = (state->dcur.frequency & 0x00ff00) >> 8;
1206 cmd.arg[3] = (state->dcur.frequency & 0x0000ff);
1207 cmd.arg[4] = ((state->dcur.symbol_rate / 1000) & 0xff00) >> 8;
1208 cmd.arg[5] = ((state->dcur.symbol_rate / 1000) & 0x00ff);
1209 cmd.arg[6] = state->dcur.inversion;
1210 cmd.arg[7] = state->dcur.fec_val | state->dcur.pilot_val;
1211 cmd.arg[8] = CX24120_SEARCH_RANGE_KHZ >> 8;
1212 cmd.arg[9] = CX24120_SEARCH_RANGE_KHZ & 0xff;
1213 cmd.arg[10] = 0; /* maybe rolloff? */
1214 cmd.arg[11] = state->dcur.fec_mask;
1215 cmd.arg[12] = state->dcur.ratediv;
1216 cmd.arg[13] = state->dcur.clkdiv;
1217 cmd.arg[14] = 0;
1218
1219 /* Send tune command */
1220 ret = cx24120_message_send(state, &cmd);
1221 if (ret != 0)
1222 return ret;
1223
1224 /* Write symbol rate values */
1225 ret = cx24120_writereg(state, CX24120_REG_CLKDIV, state->dcur.clkdiv);
1226 ret = cx24120_readreg(state, CX24120_REG_RATEDIV);
1227 ret &= 0xfffffff0;
1228 ret |= state->dcur.ratediv;
1229 ret = cx24120_writereg(state, CX24120_REG_RATEDIV, ret);
1230
1231 return 0;
1232 }
1233
1234 /* Set vco from config */
cx24120_set_vco(struct cx24120_state * state)1235 static int cx24120_set_vco(struct cx24120_state *state)
1236 {
1237 struct cx24120_cmd cmd;
1238 u32 nxtal_khz, vco;
1239 u64 inv_vco;
1240 u32 xtal_khz = state->config->xtal_khz;
1241
1242 nxtal_khz = xtal_khz * 4;
1243 vco = nxtal_khz * 10;
1244 inv_vco = DIV_ROUND_CLOSEST_ULL(0x400000000ULL, vco);
1245
1246 dev_dbg(&state->i2c->dev, "xtal=%d, vco=%d, inv_vco=%lld\n",
1247 xtal_khz, vco, inv_vco);
1248
1249 cmd.id = CMD_VCO_SET;
1250 cmd.len = 12;
1251 cmd.arg[0] = (vco >> 16) & 0xff;
1252 cmd.arg[1] = (vco >> 8) & 0xff;
1253 cmd.arg[2] = vco & 0xff;
1254 cmd.arg[3] = (inv_vco >> 8) & 0xff;
1255 cmd.arg[4] = (inv_vco) & 0xff;
1256 cmd.arg[5] = 0x03;
1257 cmd.arg[6] = (nxtal_khz >> 8) & 0xff;
1258 cmd.arg[7] = nxtal_khz & 0xff;
1259 cmd.arg[8] = 0x06;
1260 cmd.arg[9] = 0x03;
1261 cmd.arg[10] = (xtal_khz >> 16) & 0xff;
1262 cmd.arg[11] = xtal_khz & 0xff;
1263
1264 return cx24120_message_send(state, &cmd);
1265 }
1266
cx24120_init(struct dvb_frontend * fe)1267 static int cx24120_init(struct dvb_frontend *fe)
1268 {
1269 const struct firmware *fw;
1270 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
1271 struct cx24120_state *state = fe->demodulator_priv;
1272 struct cx24120_cmd cmd;
1273 u8 reg;
1274 int ret, i;
1275 unsigned char vers[4];
1276
1277 if (state->cold_init)
1278 return 0;
1279
1280 /* ???? */
1281 cx24120_writereg(state, 0xea, 0x00);
1282 cx24120_test_rom(state);
1283 reg = cx24120_readreg(state, 0xfb) & 0xfe;
1284 cx24120_writereg(state, 0xfb, reg);
1285 reg = cx24120_readreg(state, 0xfc) & 0xfe;
1286 cx24120_writereg(state, 0xfc, reg);
1287 cx24120_writereg(state, 0xc3, 0x04);
1288 cx24120_writereg(state, 0xc4, 0x04);
1289 cx24120_writereg(state, 0xce, 0x00);
1290 cx24120_writereg(state, 0xcf, 0x00);
1291 reg = cx24120_readreg(state, 0xea) & 0xfe;
1292 cx24120_writereg(state, 0xea, reg);
1293 cx24120_writereg(state, 0xeb, 0x0c);
1294 cx24120_writereg(state, 0xec, 0x06);
1295 cx24120_writereg(state, 0xed, 0x05);
1296 cx24120_writereg(state, 0xee, 0x03);
1297 cx24120_writereg(state, 0xef, 0x05);
1298 cx24120_writereg(state, 0xf3, 0x03);
1299 cx24120_writereg(state, 0xf4, 0x44);
1300
1301 for (i = 0; i < 3; i++) {
1302 cx24120_writereg(state, 0xf0 + i, 0x04);
1303 cx24120_writereg(state, 0xe6 + i, 0x02);
1304 }
1305
1306 cx24120_writereg(state, 0xea, (reg | 0x01));
1307 for (i = 0; i < 6; i += 2) {
1308 cx24120_writereg(state, 0xc5 + i, 0x00);
1309 cx24120_writereg(state, 0xc6 + i, 0x00);
1310 }
1311
1312 cx24120_writereg(state, 0xe4, 0x03);
1313 cx24120_writereg(state, 0xeb, 0x0a);
1314
1315 dev_dbg(&state->i2c->dev, "requesting firmware (%s) to download...\n",
1316 CX24120_FIRMWARE);
1317
1318 ret = state->config->request_firmware(fe, &fw, CX24120_FIRMWARE);
1319 if (ret) {
1320 err("Could not load firmware (%s): %d\n", CX24120_FIRMWARE,
1321 ret);
1322 return ret;
1323 }
1324
1325 dev_dbg(&state->i2c->dev,
1326 "Firmware found, size %d bytes (%02x %02x .. %02x %02x)\n",
1327 (int)fw->size, /* firmware_size in bytes */
1328 fw->data[0], /* fw 1st byte */
1329 fw->data[1], /* fw 2d byte */
1330 fw->data[fw->size - 2], /* fw before last byte */
1331 fw->data[fw->size - 1]); /* fw last byte */
1332
1333 cx24120_test_rom(state);
1334 reg = cx24120_readreg(state, 0xfb) & 0xfe;
1335 cx24120_writereg(state, 0xfb, reg);
1336 cx24120_writereg(state, 0xe0, 0x76);
1337 cx24120_writereg(state, 0xf7, 0x81);
1338 cx24120_writereg(state, 0xf8, 0x00);
1339 cx24120_writereg(state, 0xf9, 0x00);
1340 cx24120_writeregs(state, 0xfa, fw->data, (fw->size - 1), 0x00);
1341 cx24120_writereg(state, 0xf7, 0xc0);
1342 cx24120_writereg(state, 0xe0, 0x00);
1343 reg = (fw->size - 2) & 0x00ff;
1344 cx24120_writereg(state, 0xf8, reg);
1345 reg = ((fw->size - 2) >> 8) & 0x00ff;
1346 cx24120_writereg(state, 0xf9, reg);
1347 cx24120_writereg(state, 0xf7, 0x00);
1348 cx24120_writereg(state, 0xdc, 0x00);
1349 cx24120_writereg(state, 0xdc, 0x07);
1350 msleep(500);
1351
1352 /* Check final byte matches final byte of firmware */
1353 reg = cx24120_readreg(state, 0xe1);
1354 if (reg == fw->data[fw->size - 1]) {
1355 dev_dbg(&state->i2c->dev, "Firmware uploaded successfully\n");
1356 ret = 0;
1357 } else {
1358 err("Firmware upload failed. Last byte returned=0x%x\n", ret);
1359 ret = -EREMOTEIO;
1360 }
1361 cx24120_writereg(state, 0xdc, 0x00);
1362 release_firmware(fw);
1363 if (ret != 0)
1364 return ret;
1365
1366 /* Start tuner */
1367 cmd.id = CMD_START_TUNER;
1368 cmd.len = 3;
1369 cmd.arg[0] = 0x00;
1370 cmd.arg[1] = 0x00;
1371 cmd.arg[2] = 0x00;
1372
1373 if (cx24120_message_send(state, &cmd) != 0) {
1374 err("Error tuner start! :(\n");
1375 return -EREMOTEIO;
1376 }
1377
1378 /* Set VCO */
1379 ret = cx24120_set_vco(state);
1380 if (ret != 0) {
1381 err("Error set VCO! :(\n");
1382 return ret;
1383 }
1384
1385 /* set bandwidth */
1386 cmd.id = CMD_BANDWIDTH;
1387 cmd.len = 12;
1388 cmd.arg[0] = 0x00;
1389 cmd.arg[1] = 0x00;
1390 cmd.arg[2] = 0x00;
1391 cmd.arg[3] = 0x00;
1392 cmd.arg[4] = 0x05;
1393 cmd.arg[5] = 0x02;
1394 cmd.arg[6] = 0x02;
1395 cmd.arg[7] = 0x00;
1396 cmd.arg[8] = 0x05;
1397 cmd.arg[9] = 0x02;
1398 cmd.arg[10] = 0x02;
1399 cmd.arg[11] = 0x00;
1400
1401 if (cx24120_message_send(state, &cmd)) {
1402 err("Error set bandwidth!\n");
1403 return -EREMOTEIO;
1404 }
1405
1406 reg = cx24120_readreg(state, 0xba);
1407 if (reg > 3) {
1408 dev_dbg(&state->i2c->dev, "Reset-readreg 0xba: %x\n", ret);
1409 err("Error initialising tuner!\n");
1410 return -EREMOTEIO;
1411 }
1412
1413 dev_dbg(&state->i2c->dev, "Tuner initialised correctly.\n");
1414
1415 /* Initialise mpeg outputs */
1416 cx24120_writereg(state, 0xeb, 0x0a);
1417 if (cx24120_msg_mpeg_output_global_config(state, 0) ||
1418 cx24120_msg_mpeg_output_config(state, 0) ||
1419 cx24120_msg_mpeg_output_config(state, 1) ||
1420 cx24120_msg_mpeg_output_config(state, 2)) {
1421 err("Error initialising mpeg output. :(\n");
1422 return -EREMOTEIO;
1423 }
1424
1425 /* Set size of BER window */
1426 cmd.id = CMD_BER_CTRL;
1427 cmd.len = 3;
1428 cmd.arg[0] = 0x00;
1429 cmd.arg[1] = CX24120_BER_WINDOW;
1430 cmd.arg[2] = CX24120_BER_WINDOW;
1431 if (cx24120_message_send(state, &cmd)) {
1432 err("Error setting ber window\n");
1433 return -EREMOTEIO;
1434 }
1435
1436 /* Firmware CMD 35: Get firmware version */
1437 cmd.id = CMD_FWVERSION;
1438 cmd.len = 1;
1439 for (i = 0; i < 4; i++) {
1440 cmd.arg[0] = i;
1441 ret = cx24120_message_send(state, &cmd);
1442 if (ret != 0)
1443 return ret;
1444 vers[i] = cx24120_readreg(state, CX24120_REG_MAILBOX);
1445 }
1446 info("FW version %i.%i.%i.%i\n", vers[0], vers[1], vers[2], vers[3]);
1447
1448 /* init stats here in order signal app which stats are supported */
1449 c->strength.len = 1;
1450 c->strength.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
1451 c->cnr.len = 1;
1452 c->cnr.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
1453 c->post_bit_error.len = 1;
1454 c->post_bit_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
1455 c->post_bit_count.len = 1;
1456 c->post_bit_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
1457 c->block_error.len = 1;
1458 c->block_error.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
1459 c->block_count.len = 1;
1460 c->block_count.stat[0].scale = FE_SCALE_NOT_AVAILABLE;
1461
1462 state->cold_init = 1;
1463
1464 return 0;
1465 }
1466
cx24120_tune(struct dvb_frontend * fe,bool re_tune,unsigned int mode_flags,unsigned int * delay,enum fe_status * status)1467 static int cx24120_tune(struct dvb_frontend *fe, bool re_tune,
1468 unsigned int mode_flags, unsigned int *delay,
1469 enum fe_status *status)
1470 {
1471 struct cx24120_state *state = fe->demodulator_priv;
1472 int ret;
1473
1474 dev_dbg(&state->i2c->dev, "(%d)\n", re_tune);
1475
1476 /* TODO: Do we need to set delay? */
1477
1478 if (re_tune) {
1479 ret = cx24120_set_frontend(fe);
1480 if (ret)
1481 return ret;
1482 }
1483
1484 return cx24120_read_status(fe, status);
1485 }
1486
cx24120_get_algo(struct dvb_frontend * fe)1487 static enum dvbfe_algo cx24120_get_algo(struct dvb_frontend *fe)
1488 {
1489 return DVBFE_ALGO_HW;
1490 }
1491
cx24120_sleep(struct dvb_frontend * fe)1492 static int cx24120_sleep(struct dvb_frontend *fe)
1493 {
1494 return 0;
1495 }
1496
cx24120_get_frontend(struct dvb_frontend * fe,struct dtv_frontend_properties * c)1497 static int cx24120_get_frontend(struct dvb_frontend *fe,
1498 struct dtv_frontend_properties *c)
1499 {
1500 struct cx24120_state *state = fe->demodulator_priv;
1501 u8 freq1, freq2, freq3;
1502 int status;
1503
1504 dev_dbg(&state->i2c->dev, "\n");
1505
1506 /* don't return empty data if we're not tuned in */
1507 status = cx24120_readreg(state, CX24120_REG_STATUS);
1508 if (!(status & CX24120_HAS_LOCK))
1509 return 0;
1510
1511 /* Get frequency */
1512 freq1 = cx24120_readreg(state, CX24120_REG_FREQ1);
1513 freq2 = cx24120_readreg(state, CX24120_REG_FREQ2);
1514 freq3 = cx24120_readreg(state, CX24120_REG_FREQ3);
1515 c->frequency = (freq3 << 16) | (freq2 << 8) | freq1;
1516 dev_dbg(&state->i2c->dev, "frequency = %d\n", c->frequency);
1517
1518 /* Get modulation, fec, pilot */
1519 cx24120_get_fec(fe);
1520
1521 return 0;
1522 }
1523
cx24120_release(struct dvb_frontend * fe)1524 static void cx24120_release(struct dvb_frontend *fe)
1525 {
1526 struct cx24120_state *state = fe->demodulator_priv;
1527
1528 dev_dbg(&state->i2c->dev, "Clear state structure\n");
1529 kfree(state);
1530 }
1531
cx24120_read_ucblocks(struct dvb_frontend * fe,u32 * ucblocks)1532 static int cx24120_read_ucblocks(struct dvb_frontend *fe, u32 *ucblocks)
1533 {
1534 struct cx24120_state *state = fe->demodulator_priv;
1535 struct dtv_frontend_properties *c = &fe->dtv_property_cache;
1536
1537 if (c->block_error.stat[0].scale != FE_SCALE_COUNTER) {
1538 *ucblocks = 0;
1539 return 0;
1540 }
1541
1542 *ucblocks = c->block_error.stat[0].uvalue - state->ucb_offset;
1543
1544 return 0;
1545 }
1546
1547 static const struct dvb_frontend_ops cx24120_ops = {
1548 .delsys = { SYS_DVBS, SYS_DVBS2 },
1549 .info = {
1550 .name = "Conexant CX24120/CX24118",
1551 .frequency_min_hz = 950 * MHz,
1552 .frequency_max_hz = 2150 * MHz,
1553 .frequency_stepsize_hz = 1011 * kHz,
1554 .frequency_tolerance_hz = 5 * MHz,
1555 .symbol_rate_min = 1000000,
1556 .symbol_rate_max = 45000000,
1557 .caps = FE_CAN_INVERSION_AUTO |
1558 FE_CAN_FEC_1_2 | FE_CAN_FEC_2_3 | FE_CAN_FEC_3_4 |
1559 FE_CAN_FEC_4_5 | FE_CAN_FEC_5_6 | FE_CAN_FEC_6_7 |
1560 FE_CAN_FEC_7_8 | FE_CAN_FEC_AUTO |
1561 FE_CAN_2G_MODULATION |
1562 FE_CAN_QPSK | FE_CAN_RECOVER
1563 },
1564 .release = cx24120_release,
1565
1566 .init = cx24120_init,
1567 .sleep = cx24120_sleep,
1568
1569 .tune = cx24120_tune,
1570 .get_frontend_algo = cx24120_get_algo,
1571 .set_frontend = cx24120_set_frontend,
1572
1573 .get_frontend = cx24120_get_frontend,
1574 .read_status = cx24120_read_status,
1575 .read_ber = cx24120_read_ber,
1576 .read_signal_strength = cx24120_read_signal_strength,
1577 .read_snr = cx24120_read_snr,
1578 .read_ucblocks = cx24120_read_ucblocks,
1579
1580 .diseqc_send_master_cmd = cx24120_send_diseqc_msg,
1581
1582 .diseqc_send_burst = cx24120_diseqc_send_burst,
1583 .set_tone = cx24120_set_tone,
1584 .set_voltage = cx24120_set_voltage,
1585 };
1586
1587 MODULE_DESCRIPTION("DVB Frontend module for Conexant CX24120/CX24118 hardware");
1588 MODULE_AUTHOR("Jemma Denson");
1589 MODULE_LICENSE("GPL");
1590