1// SPDX-License-Identifier: GPL-2.0 2/* 3 * Support for CompuLab CM-T54 4 */ 5/dts-v1/; 6 7#include "omap5.dtsi" 8#include <dt-bindings/interrupt-controller/irq.h> 9#include <dt-bindings/interrupt-controller/arm-gic.h> 10 11/ { 12 model = "CompuLab CM-T54"; 13 compatible = "compulab,omap5-cm-t54", "ti,omap5"; 14 15 memory@80000000 { 16 device_type = "memory"; 17 reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */ 18 }; 19 20 aliases { 21 display0 = &hdmi0; 22 display1 = &dvi0; 23 display2 = &lcd0; 24 }; 25 26 vmmcsd_fixed: fixed-regulator-mmcsd { 27 compatible = "regulator-fixed"; 28 regulator-name = "vmmcsd_fixed"; 29 regulator-min-microvolt = <3300000>; 30 regulator-max-microvolt = <3300000>; 31 }; 32 33 vwlan_pdn_fixed: fixed-regulator-vwlan-pdn { 34 compatible = "regulator-fixed"; 35 regulator-name = "vwlan_pdn_fixed"; 36 regulator-min-microvolt = <3300000>; 37 regulator-max-microvolt = <3300000>; 38 vin-supply = <&ldo2_reg>; 39 gpio = <&gpio4 13 GPIO_ACTIVE_HIGH>; /* gpio4_109 */ 40 startup-delay-us = <1000>; 41 enable-active-high; 42 }; 43 44 vwlan_fixed: fixed-regulator-vwlan { 45 compatible = "regulator-fixed"; 46 regulator-name = "vwlan_fixed"; 47 regulator-min-microvolt = <3300000>; 48 regulator-max-microvolt = <3300000>; 49 vin-supply = <&vwlan_pdn_fixed>; 50 gpio = <&gpio4 14 GPIO_ACTIVE_HIGH>; /* gpio4_110 */ 51 startup-delay-us = <1000>; 52 enable-active-high; 53 }; 54 55 ads7846reg: ads7846-reg { 56 compatible = "regulator-fixed"; 57 regulator-name = "ads7846-reg"; 58 regulator-min-microvolt = <3300000>; 59 regulator-max-microvolt = <3300000>; 60 }; 61 62 /* HS USB Host PHY on PORT 2 */ 63 hsusb2_phy: hsusb2_phy { 64 compatible = "usb-nop-xceiv"; 65 reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */ 66 #phy-cells = <0>; 67 }; 68 69 /* HS USB Host PHY on PORT 3 */ 70 hsusb3_phy: hsusb3_phy { 71 compatible = "usb-nop-xceiv"; 72 reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */ 73 #phy-cells = <0>; 74 }; 75 76 leds { 77 compatible = "gpio-leds"; 78 led1 { 79 label = "Heartbeat"; 80 gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */ 81 linux,default-trigger = "heartbeat"; 82 default-state = "off"; 83 }; 84 }; 85 86 lcd0: display { 87 compatible = "startek,startek-kd050c", "panel-dpi"; 88 label = "lcd"; 89 90 pinctrl-names = "default"; 91 pinctrl-0 = <&lcd_pins>; 92 93 enable-gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>; 94 95 panel-timing { 96 clock-frequency = <33000000>; 97 hactive = <800>; 98 vactive = <480>; 99 hfront-porch = <40>; 100 hback-porch = <40>; 101 hsync-len = <43>; 102 vback-porch = <29>; 103 vfront-porch = <13>; 104 vsync-len = <3>; 105 hsync-active = <0>; 106 vsync-active = <0>; 107 de-active = <1>; 108 pixelclk-active = <1>; 109 }; 110 111 port { 112 lcd_in: endpoint { 113 remote-endpoint = <&dpi_lcd_out>; 114 }; 115 }; 116 }; 117 118 hdmi0: connector0 { 119 compatible = "hdmi-connector"; 120 label = "hdmi"; 121 122 type = "a"; 123 124 pinctrl-names = "default"; 125 pinctrl-0 = <&hdmi_conn_pins>; 126 127 hpd-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>; /* GPIO 193, HPD */ 128 129 port { 130 hdmi_connector_in: endpoint { 131 remote-endpoint = <&hdmi_out>; 132 }; 133 }; 134 }; 135 136 tfp410: encoder0 { 137 compatible = "ti,tfp410"; 138 139 ports { 140 #address-cells = <1>; 141 #size-cells = <0>; 142 143 port@0 { 144 reg = <0>; 145 146 tfp410_in: endpoint { 147 remote-endpoint = <&dpi_dvi_out>; 148 }; 149 }; 150 151 port@1 { 152 reg = <1>; 153 154 tfp410_out: endpoint { 155 remote-endpoint = <&dvi_connector_in>; 156 }; 157 }; 158 }; 159 }; 160 161 dvi0: connector1 { 162 compatible = "dvi-connector"; 163 label = "dvi"; 164 165 digital; 166 167 ddc-i2c-bus = <&i2c2>; 168 169 port { 170 dvi_connector_in: endpoint { 171 remote-endpoint = <&tfp410_out>; 172 }; 173 }; 174 }; 175}; 176 177&omap5_pmx_wkup { 178 179 ads7846_pins: pinmux_ads7846_pins { 180 pinctrl-single,pins = < 181 OMAP5_IOPAD(0x0042, PIN_INPUT_PULLDOWN | MUX_MODE6) /* llib_wakereqin.gpio1_wk15 */ 182 >; 183 }; 184 185 palmas_sys_nirq_pins: pinmux_palmas_sys_nirq_pins { 186 pinctrl-single,pins = < 187 /* sys_nirq1 is pulled down as the SoC is inverting it for GIC */ 188 OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0) 189 >; 190 }; 191}; 192 193&omap5_pmx_core { 194 pinctrl-names = "default"; 195 pinctrl-0 = < 196 &led_gpio_pins 197 &usbhost_pins 198 >; 199 200 led_gpio_pins: pinmux_led_gpio_pins { 201 pinctrl-single,pins = < 202 OMAP5_IOPAD(0x00b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */ 203 >; 204 }; 205 206 i2c1_pins: pinmux_i2c1_pins { 207 pinctrl-single,pins = < 208 OMAP5_IOPAD(0x01f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */ 209 OMAP5_IOPAD(0x01f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */ 210 >; 211 }; 212 213 i2c2_pins: pinmux_i2c2_pins { 214 pinctrl-single,pins = < 215 OMAP5_IOPAD(0x01b8, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ 216 OMAP5_IOPAD(0x01ba, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ 217 >; 218 }; 219 220 mmc1_pins: pinmux_mmc1_pins { 221 pinctrl-single,pins = < 222 OMAP5_IOPAD(0x01e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */ 223 OMAP5_IOPAD(0x01e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */ 224 OMAP5_IOPAD(0x01e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */ 225 OMAP5_IOPAD(0x01e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */ 226 OMAP5_IOPAD(0x01ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */ 227 OMAP5_IOPAD(0x01ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */ 228 >; 229 }; 230 231 mmc2_pins: pinmux_mmc2_pins { 232 pinctrl-single,pins = < 233 OMAP5_IOPAD(0x0040, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */ 234 OMAP5_IOPAD(0x0042, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */ 235 OMAP5_IOPAD(0x0044, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */ 236 OMAP5_IOPAD(0x0046, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */ 237 OMAP5_IOPAD(0x0048, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */ 238 OMAP5_IOPAD(0x004a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */ 239 OMAP5_IOPAD(0x004c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */ 240 OMAP5_IOPAD(0x004e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */ 241 OMAP5_IOPAD(0x0050, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */ 242 OMAP5_IOPAD(0x0052, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */ 243 >; 244 }; 245 246 mmc3_pins: pinmux_mmc3_pins { 247 pinctrl-single,pins = < 248 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */ 249 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */ 250 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */ 251 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */ 252 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */ 253 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */ 254 >; 255 }; 256 257 wlan_gpios_pins: pinmux_wlan_gpios_pins { 258 pinctrl-single,pins = < 259 OMAP5_IOPAD(0x019c, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_ul_data.gpio4_109 */ 260 OMAP5_IOPAD(0x019e, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* abemcpdm_dl_data.gpio4_110 */ 261 >; 262 }; 263 264 usbhost_pins: pinmux_usbhost_pins { 265 pinctrl-single,pins = < 266 OMAP5_IOPAD(0x00c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ 267 OMAP5_IOPAD(0x00c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ 268 269 OMAP5_IOPAD(0x01dc, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ 270 OMAP5_IOPAD(0x01de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ 271 272 OMAP5_IOPAD(0x00a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */ 273 OMAP5_IOPAD(0x00b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */ 274 >; 275 }; 276 277 dss_hdmi_pins: pinmux_dss_hdmi_pins { 278 pinctrl-single,pins = < 279 OMAP5_IOPAD(0x013c, PIN_INPUT | MUX_MODE0) /* hdmi_cec */ 280 OMAP5_IOPAD(0x0140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl */ 281 OMAP5_IOPAD(0x0142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda */ 282 >; 283 }; 284 285 lcd_pins: pinmux_lcd_pins { 286 pinctrl-single,pins = < 287 OMAP5_IOPAD(0x0172, PIN_OUTPUT_PULLDOWN | MUX_MODE6) /* timer11_pwm_evt.gpio8_227 */ 288 >; 289 }; 290 291 hdmi_conn_pins: pinmux_hdmi_conn_pins { 292 pinctrl-single,pins = < 293 OMAP5_IOPAD(0x013e, PIN_INPUT | MUX_MODE6) /* hdmi_hpd.gpio7_193 */ 294 >; 295 }; 296 297 dss_dpi_pins: pinmux_dss_dpi_pins { 298 pinctrl-single,pins = < 299 OMAP5_IOPAD(0x0104, PIN_OUTPUT | MUX_MODE3) /* rfbi_data15.dispc_data15 */ 300 OMAP5_IOPAD(0x0106, PIN_OUTPUT | MUX_MODE3) /* rfbi_data14.dispc_data14 */ 301 OMAP5_IOPAD(0x0108, PIN_OUTPUT | MUX_MODE3) /* rfbi_data13.dispc_data13 */ 302 OMAP5_IOPAD(0x010a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data12.dispc_data12 */ 303 OMAP5_IOPAD(0x010c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data11.dispc_data11 */ 304 OMAP5_IOPAD(0x010e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data10.dispc_data10 */ 305 OMAP5_IOPAD(0x0110, PIN_OUTPUT | MUX_MODE3) /* rfbi_data9.dispc_data9 */ 306 OMAP5_IOPAD(0x0112, PIN_OUTPUT | MUX_MODE3) /* rfbi_data8.dispc_data8 */ 307 OMAP5_IOPAD(0x0114, PIN_OUTPUT | MUX_MODE3) /* rfbi_data7.dispc_data7 */ 308 OMAP5_IOPAD(0x0116, PIN_OUTPUT | MUX_MODE3) /* rfbi_data6.dispc_data6 */ 309 OMAP5_IOPAD(0x0118, PIN_OUTPUT | MUX_MODE3) /* rfbi_data5.dispc_data5 */ 310 OMAP5_IOPAD(0x011a, PIN_OUTPUT | MUX_MODE3) /* rfbi_data4.dispc_data4 */ 311 OMAP5_IOPAD(0x011c, PIN_OUTPUT | MUX_MODE3) /* rfbi_data3.dispc_data3 */ 312 OMAP5_IOPAD(0x011e, PIN_OUTPUT | MUX_MODE3) /* rfbi_data2.dispc_data2 */ 313 OMAP5_IOPAD(0x0120, PIN_OUTPUT | MUX_MODE3) /* rfbi_data1.dispc_data1 */ 314 OMAP5_IOPAD(0x0122, PIN_OUTPUT | MUX_MODE3) /* rfbi_data0.dispc_data0 */ 315 OMAP5_IOPAD(0x0124, PIN_OUTPUT | MUX_MODE3) /* rfbi_we.dispc_vsync */ 316 OMAP5_IOPAD(0x0126, PIN_OUTPUT | MUX_MODE3) /* rfbi_cs0.dispc_hsync */ 317 OMAP5_IOPAD(0x0128, PIN_OUTPUT | MUX_MODE3) /* rfbi_a0.dispc_de */ 318 OMAP5_IOPAD(0x012a, PIN_OUTPUT | MUX_MODE3) /* rfbi_re.dispc_pclk */ 319 OMAP5_IOPAD(0x012c, PIN_OUTPUT | MUX_MODE3) /* rfbi_hsync0.dispc_data17 */ 320 OMAP5_IOPAD(0x012e, PIN_OUTPUT | MUX_MODE3) /* rfbi_te_vsync0.dispc_data16 */ 321 OMAP5_IOPAD(0x0130, PIN_OUTPUT | MUX_MODE3) /* gpio6_182.dispc_data18 */ 322 OMAP5_IOPAD(0x0132, PIN_OUTPUT | MUX_MODE3) /* gpio6_183.dispc_data19 */ 323 OMAP5_IOPAD(0x0134, PIN_OUTPUT | MUX_MODE3) /* gpio6_184.dispc_data20 */ 324 OMAP5_IOPAD(0x0136, PIN_OUTPUT | MUX_MODE3) /* gpio6_185.dispc_data21 */ 325 OMAP5_IOPAD(0x0138, PIN_OUTPUT | MUX_MODE3) /* gpio6_186.dispc_data22 */ 326 OMAP5_IOPAD(0x013a, PIN_OUTPUT | MUX_MODE3) /* gpio6_187.dispc_data23 */ 327 >; 328 }; 329 330 mcspi2_pins: pinmux_mcspi1_pins { 331 pinctrl-single,pins = < 332 OMAP5_IOPAD(0x00fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ 333 OMAP5_IOPAD(0x00fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ 334 OMAP5_IOPAD(0x0100, PIN_INPUT | MUX_MODE0) /* mcspi2_somi */ 335 OMAP5_IOPAD(0x0102, PIN_INPUT | MUX_MODE0) /* mcspi2_cs0 */ 336 >; 337 }; 338}; 339 340&mcspi2 { 341 pinctrl-names = "default"; 342 pinctrl-0 = <&mcspi2_pins>; 343 344 /* touch controller */ 345 ads7846@0 { 346 pinctrl-names = "default"; 347 pinctrl-0 = <&ads7846_pins>; 348 349 compatible = "ti,ads7846"; 350 vcc-supply = <&ads7846reg>; 351 352 reg = <0>; /* CS0 */ 353 spi-max-frequency = <1500000>; 354 355 interrupt-parent = <&gpio1>; 356 interrupts = <15 0>; /* gpio1_wk15 */ 357 pendown-gpio = <&gpio1 15 GPIO_ACTIVE_HIGH>; 358 359 360 ti,x-min = /bits/ 16 <0x0>; 361 ti,x-max = /bits/ 16 <0x0fff>; 362 ti,y-min = /bits/ 16 <0x0>; 363 ti,y-max = /bits/ 16 <0x0fff>; 364 365 ti,x-plate-ohms = /bits/ 16 <180>; 366 ti,pressure-max = /bits/ 16 <255>; 367 368 ti,debounce-max = /bits/ 16 <30>; 369 ti,debounce-tol = /bits/ 16 <10>; 370 ti,debounce-rep = /bits/ 16 <1>; 371 372 wakeup-source; 373 }; 374}; 375 376&mmc1 { 377 pinctrl-names = "default"; 378 pinctrl-0 = <&mmc1_pins>; 379 vmmc-supply = <&ldo9_reg>; 380 bus-width = <4>; 381}; 382 383&mmc2 { 384 pinctrl-names = "default"; 385 pinctrl-0 = <&mmc2_pins>; 386 vmmc-supply = <&vmmcsd_fixed>; 387 bus-width = <8>; 388 ti,non-removable; 389}; 390 391&mmc3 { 392 pinctrl-names = "default"; 393 pinctrl-0 = < 394 &mmc3_pins 395 &wlan_gpios_pins 396 >; 397 vmmc-supply = <&vwlan_fixed>; 398 bus-width = <4>; 399 ti,non-removable; 400}; 401 402&mmc4 { 403 status = "disabled"; 404}; 405 406&mmc5 { 407 status = "disabled"; 408}; 409 410&i2c1 { 411 pinctrl-names = "default"; 412 pinctrl-0 = <&i2c1_pins>; 413 414 clock-frequency = <400000>; 415 416 at24@50 { 417 compatible = "atmel,24c02"; 418 pagesize = <16>; 419 reg = <0x50>; 420 }; 421 422 palmas: palmas@48 { 423 compatible = "ti,palmas"; 424 reg = <0x48>; 425 pinctrl-0 = <&palmas_sys_nirq_pins>; 426 pinctrl-names = "default"; 427 /* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */ 428 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_LOW>; 429 interrupt-controller; 430 #interrupt-cells = <2>; 431 ti,system-power-controller; 432 433 extcon_usb3: palmas_usb { 434 compatible = "ti,palmas-usb-vid"; 435 ti,enable-vbus-detection; 436 ti,enable-id-detection; 437 ti,wakeup; 438 }; 439 440 rtc { 441 compatible = "ti,palmas-rtc"; 442 interrupt-parent = <&palmas>; 443 interrupts = <8 IRQ_TYPE_NONE>; 444 }; 445 446 palmas_pmic { 447 compatible = "ti,palmas-pmic"; 448 interrupt-parent = <&palmas>; 449 interrupts = <14 IRQ_TYPE_NONE>; 450 interrupt-names = "short-irq"; 451 452 ti,ldo6-vibrator; 453 454 regulators { 455 smps123_reg: smps123 { 456 /* VDD_OPP_MPU */ 457 regulator-name = "smps123"; 458 regulator-min-microvolt = < 600000>; 459 regulator-max-microvolt = <1500000>; 460 regulator-always-on; 461 regulator-boot-on; 462 }; 463 464 smps45_reg: smps45 { 465 /* VDD_OPP_MM */ 466 regulator-name = "smps45"; 467 regulator-min-microvolt = < 600000>; 468 regulator-max-microvolt = <1310000>; 469 regulator-always-on; 470 regulator-boot-on; 471 }; 472 473 smps6_reg: smps6 { 474 /* VDD_DDR3 - over VDD_SMPS6 */ 475 regulator-name = "smps6"; 476 regulator-min-microvolt = <1500000>; 477 regulator-max-microvolt = <1500000>; 478 regulator-always-on; 479 regulator-boot-on; 480 }; 481 482 smps7_reg: smps7 { 483 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ 484 regulator-name = "smps7"; 485 regulator-min-microvolt = <1800000>; 486 regulator-max-microvolt = <1800000>; 487 regulator-always-on; 488 regulator-boot-on; 489 }; 490 491 smps8_reg: smps8 { 492 /* VDD_OPP_CORE */ 493 regulator-name = "smps8"; 494 regulator-min-microvolt = < 600000>; 495 regulator-max-microvolt = <1310000>; 496 regulator-always-on; 497 regulator-boot-on; 498 }; 499 500 smps9_reg: smps9 { 501 /* VDDA_2v1_AUD over VDD_2v1 */ 502 regulator-name = "smps9"; 503 regulator-min-microvolt = <3300000>; 504 regulator-max-microvolt = <3300000>; 505 ti,smps-range = <0x80>; 506 regulator-always-on; 507 regulator-boot-on; 508 }; 509 510 smps10_out2_reg: smps10_out2 { 511 /* VBUS_5V_OTG */ 512 regulator-name = "smps10_out2"; 513 regulator-min-microvolt = <5000000>; 514 regulator-max-microvolt = <5000000>; 515 regulator-always-on; 516 regulator-boot-on; 517 }; 518 519 smps10_out1_reg: smps10_out1 { 520 /* VBUS_5V_OTG */ 521 regulator-name = "smps10_out1"; 522 regulator-min-microvolt = <5000000>; 523 regulator-max-microvolt = <5000000>; 524 }; 525 526 ldo1_reg: ldo1 { 527 /* VDDAPHY_CAM: vdda_csiport */ 528 regulator-name = "ldo1"; 529 regulator-min-microvolt = <1800000>; 530 regulator-max-microvolt = <1800000>; 531 }; 532 533 ldo2_reg: ldo2 { 534 /* VDD_3V3_WLAN */ 535 regulator-name = "ldo2"; 536 regulator-min-microvolt = <3300000>; 537 regulator-max-microvolt = <3300000>; 538 startup-delay-us = <1000>; 539 }; 540 541 ldo3_reg: ldo3 { 542 /* VCC_1V5_AUD */ 543 regulator-name = "ldo3"; 544 regulator-min-microvolt = <1500000>; 545 regulator-max-microvolt = <1500000>; 546 regulator-always-on; 547 regulator-boot-on; 548 }; 549 550 ldo4_reg: ldo4 { 551 /* VDDAPHY_DISP: vdda_dsiport/hdmi */ 552 regulator-name = "ldo4"; 553 regulator-min-microvolt = <1800000>; 554 regulator-max-microvolt = <1800000>; 555 }; 556 557 ldo5_reg: ldo5 { 558 /* VDDA_1V8_PHY: usb/sata/hdmi.. */ 559 regulator-name = "ldo5"; 560 regulator-min-microvolt = <1800000>; 561 regulator-max-microvolt = <1800000>; 562 regulator-always-on; 563 regulator-boot-on; 564 }; 565 566 ldo6_reg: ldo6 { 567 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ 568 regulator-name = "ldo6"; 569 regulator-min-microvolt = <1200000>; 570 regulator-max-microvolt = <1200000>; 571 regulator-always-on; 572 regulator-boot-on; 573 }; 574 575 ldo7_reg: ldo7 { 576 /* VDD_VPP: vpp1 */ 577 regulator-name = "ldo7"; 578 regulator-min-microvolt = <2000000>; 579 regulator-max-microvolt = <2000000>; 580 /* Only for efuse reprograming! */ 581 status = "disabled"; 582 }; 583 584 ldo8_reg: ldo8 { 585 /* VDD_3V_GP: act led/serial console */ 586 regulator-name = "ldo8"; 587 regulator-min-microvolt = <3000000>; 588 regulator-max-microvolt = <3000000>; 589 regulator-always-on; 590 regulator-boot-on; 591 }; 592 593 ldo9_reg: ldo9 { 594 /* VCC_DV_SDIO: vdds_sdcard */ 595 regulator-name = "ldo9"; 596 regulator-min-microvolt = <1800000>; 597 regulator-max-microvolt = <3000000>; 598 regulator-boot-on; 599 }; 600 601 ldoln_reg: ldoln { 602 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ 603 regulator-name = "ldoln"; 604 regulator-min-microvolt = <1800000>; 605 regulator-max-microvolt = <1800000>; 606 regulator-always-on; 607 regulator-boot-on; 608 }; 609 610 ldousb_reg: ldousb { 611 /* VDDA_3V_USB: VDDA_USBHS33 */ 612 regulator-name = "ldousb"; 613 regulator-min-microvolt = <3250000>; 614 regulator-max-microvolt = <3250000>; 615 regulator-always-on; 616 regulator-boot-on; 617 }; 618 619 regen3_reg: regen3 { 620 /* REGEN3 controls LDO9 supply to card */ 621 regulator-name = "regen3"; 622 regulator-always-on; 623 regulator-boot-on; 624 }; 625 }; 626 }; 627 }; 628}; 629 630&i2c2 { 631 pinctrl-names = "default"; 632 pinctrl-0 = <&i2c2_pins>; 633 634 clock-frequency = <100000>; 635}; 636 637&usbhshost { 638 port2-mode = "ehci-hsic"; 639 port3-mode = "ehci-hsic"; 640}; 641 642&usbhsehci { 643 phys = <0 &hsusb2_phy &hsusb3_phy>; 644}; 645 646&usb3 { 647 extcon = <&extcon_usb3>; 648 vbus-supply = <&smps10_out1_reg>; 649}; 650 651&cpu0 { 652 cpu0-supply = <&smps123_reg>; 653}; 654 655&dss { 656 status = "okay"; 657 658 pinctrl-names = "default"; 659 pinctrl-0 = <&dss_dpi_pins>; 660 661 port { 662 #address-cells = <1>; 663 #size-cells = <0>; 664 665 dpi_dvi_out: endpoint@0 { 666 reg = <0>; 667 remote-endpoint = <&tfp410_in>; 668 data-lines = <24>; 669 }; 670 671 dpi_lcd_out: endpoint@1 { 672 reg = <1>; 673 remote-endpoint = <&lcd_in>; 674 data-lines = <24>; 675 }; 676 }; 677}; 678 679&dsi2 { 680 status = "okay"; 681 vdd-supply = <&ldo4_reg>; 682}; 683 684&hdmi { 685 status = "okay"; 686 vdda-supply = <&ldo4_reg>; 687 688 pinctrl-names = "default"; 689 pinctrl-0 = <&dss_hdmi_pins>; 690 691 port { 692 hdmi_out: endpoint { 693 remote-endpoint = <&hdmi_connector_in>; 694 lanes = <1 0 3 2 5 4 7 6>; 695 }; 696 }; 697}; 698