1// SPDX-License-Identifier: GPL-2.0-only 2/* 3 * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/ 4 * Copyright (C) 2014 Stefan Roese <sr@denx.de> 5 */ 6/dts-v1/; 7 8#include "omap34xx.dtsi" 9 10/* Secure omaps have some devices inaccessible depending on the firmware */ 11&aes1_target { 12 status = "disabled"; 13}; 14 15&aes2_target { 16 status = "disabled"; 17}; 18 19&sham { 20 status = "disabled"; 21}; 22 23/ { 24 cpus { 25 cpu@0 { 26 cpu0-supply = <&vcc>; 27 }; 28 }; 29 30 memory@80000000 { 31 device_type = "memory"; 32 reg = <0x80000000 0x10000000>; /* 256 MB */ 33 }; 34 35 /* HS USB Port 2 Power */ 36 hsusb2_power: hsusb2_power_reg { 37 compatible = "regulator-fixed"; 38 regulator-name = "hsusb2_vbus"; 39 regulator-min-microvolt = <3300000>; 40 regulator-max-microvolt = <3300000>; 41 gpio = <&twl_gpio 18 GPIO_ACTIVE_HIGH>; /* GPIO LEDA */ 42 startup-delay-us = <70000>; 43 }; 44 45 /* HS USB Host PHY on PORT 2 */ 46 hsusb2_phy: hsusb2_phy { 47 compatible = "usb-nop-xceiv"; 48 reset-gpios = <&gpio6 2 GPIO_ACTIVE_LOW>; /* gpio_162 */ 49 vcc-supply = <&hsusb2_power>; 50 #phy-cells = <0>; 51 }; 52 53 sound { 54 compatible = "ti,omap-twl4030"; 55 ti,model = "omap3beagle"; 56 57 /* McBSP2 is used for onboard sound, same as on beagle */ 58 ti,mcbsp = <&mcbsp2>; 59 }; 60 61 /* Regulator to enable/switch the vcc of the Wifi module */ 62 mmc2_sdio_poweron: regulator-mmc2-sdio-poweron { 63 compatible = "regulator-fixed"; 64 regulator-name = "regulator-mmc2-sdio-poweron"; 65 regulator-min-microvolt = <3150000>; 66 regulator-max-microvolt = <3150000>; 67 gpio = <&gpio5 29 GPIO_ACTIVE_LOW>; /* gpio_157 */ 68 startup-delay-us = <10000>; 69 }; 70}; 71 72&omap3_pmx_core { 73 hsusbb2_pins: pinmux_hsusbb2_pins { 74 pinctrl-single,pins = < 75 OMAP3_CORE1_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ 76 OMAP3_CORE1_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ 77 OMAP3_CORE1_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ 78 OMAP3_CORE1_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ 79 OMAP3_CORE1_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ 80 OMAP3_CORE1_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ 81 OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ 82 OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ 83 OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ 84 OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ 85 OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ 86 OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ 87 >; 88 }; 89 90 mmc1_pins: pinmux_mmc1_pins { 91 pinctrl-single,pins = < 92 OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ 93 OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ 94 OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ 95 OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ 96 OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ 97 OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ 98 OMAP3_CORE1_IOPAD(0x2150, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ 99 OMAP3_CORE1_IOPAD(0x2152, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ 100 OMAP3_CORE1_IOPAD(0x2154, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ 101 OMAP3_CORE1_IOPAD(0x2156, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ 102 >; 103 }; 104 105 mmc2_pins: pinmux_mmc2_pins { 106 pinctrl-single,pins = < 107 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ 108 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ 109 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ 110 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ 111 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ 112 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ 113 >; 114 }; 115 116 /* wlan GPIO output for WLAN_EN */ 117 wlan_gpio: pinmux_wlan_gpio { 118 pinctrl-single,pins = < 119 OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr gpio_157 */ 120 >; 121 }; 122 123 uart3_pins: pinmux_uart3_pins { 124 pinctrl-single,pins = < 125 OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ 126 OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ 127 >; 128 }; 129 130 i2c3_pins: pinmux_i2c3_pins { 131 pinctrl-single,pins = < 132 OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl.i2c3_scl */ 133 OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda.i2c3_sda */ 134 >; 135 }; 136 137 mcspi1_pins: pinmux_mcspi1_pins { 138 pinctrl-single,pins = < 139 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ 140 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ 141 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ 142 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ 143 >; 144 }; 145 146 mcspi3_pins: pinmux_mcspi3_pins { 147 pinctrl-single,pins = < 148 OMAP3_CORE1_IOPAD(0x25dc, PIN_OUTPUT | MUX_MODE1) /* etk_d0.mcspi3_simo gpio14 INPUT | MODE1 */ 149 OMAP3_CORE1_IOPAD(0x25de, PIN_INPUT_PULLUP | MUX_MODE1) /* etk_d1.mcspi3_somi gpio15 INPUT | MODE1 */ 150 OMAP3_CORE1_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE1) /* etk_d2.mcspi3_cs0 gpio16 INPUT | MODE1 */ 151 OMAP3_CORE1_IOPAD(0x25e2, PIN_INPUT | MUX_MODE1) /* etk_d3.mcspi3_clk gpio17 INPUT | MODE1 */ 152 >; 153 }; 154 155 mcbsp3_pins: pinmux_mcbsp3_pins { 156 pinctrl-single,pins = < 157 OMAP3_CORE1_IOPAD(0x216c, PIN_OUTPUT | MUX_MODE0) /* mcbsp3_dx.uart2_cts */ 158 OMAP3_CORE1_IOPAD(0x216e, PIN_INPUT | MUX_MODE0) /* mcbsp3_dr.uart2_rts */ 159 OMAP3_CORE1_IOPAD(0x2170, PIN_INPUT | MUX_MODE0) /* mcbsp3_clk.uart2_tx */ 160 OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE0) /* mcbsp3_fsx.uart2_rx */ 161 >; 162 }; 163}; 164 165/* McBSP1: mux'ed with GPIO158 as clock for HA-DSP */ 166&mcbsp1 { 167 status = "disabled"; 168}; 169 170&mcbsp2 { 171 status = "okay"; 172}; 173 174&i2c1 { 175 clock-frequency = <2600000>; 176 177 twl: twl@48 { 178 reg = <0x48>; 179 interrupts = <7>; /* SYS_NIRQ cascaded to intc */ 180 interrupt-parent = <&intc>; 181 182 twl_audio: audio { 183 compatible = "ti,twl4030-audio"; 184 codec { 185 }; 186 }; 187 }; 188}; 189 190&i2c3 { 191 clock-frequency = <100000>; 192 193 pinctrl-names = "default"; 194 pinctrl-0 = <&i2c3_pins>; 195}; 196 197&mcspi1 { 198 pinctrl-names = "default"; 199 pinctrl-0 = <&mcspi1_pins>; 200}; 201 202&mcspi3 { 203 pinctrl-names = "default"; 204 pinctrl-0 = <&mcspi3_pins>; 205}; 206 207#include "twl4030.dtsi" 208#include "twl4030_omap3.dtsi" 209 210&mmc1 { 211 pinctrl-names = "default"; 212 pinctrl-0 = <&mmc1_pins>; 213 vmmc-supply = <&vmmc1>; 214 vqmmc-supply = <&vsim>; 215 cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; 216 bus-width = <8>; 217}; 218 219// WiFi (Marvell 88W8686) on MMC2/SDIO 220&mmc2 { 221 pinctrl-names = "default"; 222 pinctrl-0 = <&mmc2_pins>; 223 vmmc-supply = <&mmc2_sdio_poweron>; 224 non-removable; 225 bus-width = <4>; 226 cap-power-off-card; 227}; 228 229&mmc3 { 230 status = "disabled"; 231}; 232 233&usbhshost { 234 port2-mode = "ehci-phy"; 235}; 236 237&usbhsehci { 238 phys = <0 &hsusb2_phy>; 239}; 240 241&twl_gpio { 242 ti,use-leds; 243 /* pullups: BIT(1) */ 244 ti,pullups = <0x000002>; 245 /* 246 * pulldowns: 247 * BIT(2), BIT(6), BIT(7), BIT(8), BIT(13) 248 * BIT(15), BIT(16), BIT(17) 249 */ 250 ti,pulldowns = <0x03a1c4>; 251}; 252 253&uart3 { 254 pinctrl-names = "default"; 255 pinctrl-0 = <&uart3_pins>; 256}; 257 258&mcbsp3 { 259 status = "okay"; 260 pinctrl-names = "default"; 261 pinctrl-0 = <&mcbsp3_pins>; 262}; 263 264&gpmc { 265 ranges = <0 0 0x30000000 0x01000000>; /* CS0: 16MB for NAND */ 266 267 nand@0,0 { 268 compatible = "ti,omap2-nand"; 269 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ 270 interrupt-parent = <&gpmc>; 271 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ 272 <1 IRQ_TYPE_NONE>; /* termcount */ 273 nand-bus-width = <16>; 274 gpmc,device-width = <2>; /* GPMC_DEVWIDTH_16BIT */ 275 ti,nand-ecc-opt = "sw"; 276 277 gpmc,cs-on-ns = <0>; 278 gpmc,cs-rd-off-ns = <36>; 279 gpmc,cs-wr-off-ns = <36>; 280 gpmc,adv-on-ns = <6>; 281 gpmc,adv-rd-off-ns = <24>; 282 gpmc,adv-wr-off-ns = <36>; 283 gpmc,oe-on-ns = <6>; 284 gpmc,oe-off-ns = <48>; 285 gpmc,we-on-ns = <6>; 286 gpmc,we-off-ns = <30>; 287 gpmc,rd-cycle-ns = <72>; 288 gpmc,wr-cycle-ns = <72>; 289 gpmc,access-ns = <54>; 290 gpmc,wr-access-ns = <30>; 291 292 #address-cells = <1>; 293 #size-cells = <1>; 294 295 x-loader@0 { 296 label = "X-Loader"; 297 reg = <0 0x80000>; 298 }; 299 300 bootloaders@80000 { 301 label = "U-Boot"; 302 reg = <0x80000 0x1e0000>; 303 }; 304 305 bootloaders_env@260000 { 306 label = "U-Boot Env"; 307 reg = <0x260000 0x20000>; 308 }; 309 310 kernel@280000 { 311 label = "Kernel"; 312 reg = <0x280000 0x400000>; 313 }; 314 315 filesystem@680000 { 316 label = "File System"; 317 reg = <0x680000 0xf980000>; 318 }; 319 }; 320}; 321 322&usb_otg_hs { 323 interface-type = <0>; 324 usb-phy = <&usb2_phy>; 325 phys = <&usb2_phy>; 326 phy-names = "usb2-phy"; 327 mode = <3>; 328 power = <50>; 329}; 330 331&vaux2 { 332 regulator-name = "vdd_ehci"; 333 regulator-min-microvolt = <1800000>; 334 regulator-max-microvolt = <1800000>; 335 regulator-always-on; 336}; 337