1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * RDA8810PL serial device driver
4  *
5  * Copyright RDA Microelectronics Company Limited
6  * Copyright (c) 2017 Andreas Färber
7  * Copyright (c) 2018 Manivannan Sadhasivam
8  */
9 
10 #include <linux/clk.h>
11 #include <linux/console.h>
12 #include <linux/delay.h>
13 #include <linux/io.h>
14 #include <linux/module.h>
15 #include <linux/of.h>
16 #include <linux/platform_device.h>
17 #include <linux/serial.h>
18 #include <linux/serial_core.h>
19 #include <linux/tty.h>
20 #include <linux/tty_flip.h>
21 
22 #define RDA_UART_PORT_NUM 3
23 #define RDA_UART_DEV_NAME "ttyRDA"
24 
25 #define RDA_UART_CTRL		0x00
26 #define RDA_UART_STATUS		0x04
27 #define RDA_UART_RXTX_BUFFER	0x08
28 #define RDA_UART_IRQ_MASK	0x0c
29 #define RDA_UART_IRQ_CAUSE	0x10
30 #define RDA_UART_IRQ_TRIGGERS	0x14
31 #define RDA_UART_CMD_SET	0x18
32 #define RDA_UART_CMD_CLR	0x1c
33 
34 /* UART_CTRL Bits */
35 #define RDA_UART_ENABLE			BIT(0)
36 #define RDA_UART_DBITS_8		BIT(1)
37 #define RDA_UART_TX_SBITS_2		BIT(2)
38 #define RDA_UART_PARITY_EN		BIT(3)
39 #define RDA_UART_PARITY(x)		(((x) & 0x3) << 4)
40 #define RDA_UART_PARITY_ODD		RDA_UART_PARITY(0)
41 #define RDA_UART_PARITY_EVEN		RDA_UART_PARITY(1)
42 #define RDA_UART_PARITY_SPACE		RDA_UART_PARITY(2)
43 #define RDA_UART_PARITY_MARK		RDA_UART_PARITY(3)
44 #define RDA_UART_DIV_MODE		BIT(20)
45 #define RDA_UART_IRDA_EN		BIT(21)
46 #define RDA_UART_DMA_EN			BIT(22)
47 #define RDA_UART_FLOW_CNT_EN		BIT(23)
48 #define RDA_UART_LOOP_BACK_EN		BIT(24)
49 #define RDA_UART_RX_LOCK_ERR		BIT(25)
50 #define RDA_UART_RX_BREAK_LEN(x)	(((x) & 0xf) << 28)
51 
52 /* UART_STATUS Bits */
53 #define RDA_UART_RX_FIFO(x)		(((x) & 0x7f) << 0)
54 #define RDA_UART_RX_FIFO_MASK		(0x7f << 0)
55 #define RDA_UART_TX_FIFO(x)		(((x) & 0x1f) << 8)
56 #define RDA_UART_TX_FIFO_MASK		(0x1f << 8)
57 #define RDA_UART_TX_ACTIVE		BIT(14)
58 #define RDA_UART_RX_ACTIVE		BIT(15)
59 #define RDA_UART_RX_OVERFLOW_ERR	BIT(16)
60 #define RDA_UART_TX_OVERFLOW_ERR	BIT(17)
61 #define RDA_UART_RX_PARITY_ERR		BIT(18)
62 #define RDA_UART_RX_FRAMING_ERR		BIT(19)
63 #define RDA_UART_RX_BREAK_INT		BIT(20)
64 #define RDA_UART_DCTS			BIT(24)
65 #define RDA_UART_CTS			BIT(25)
66 #define RDA_UART_DTR			BIT(28)
67 #define RDA_UART_CLK_ENABLED		BIT(31)
68 
69 /* UART_RXTX_BUFFER Bits */
70 #define RDA_UART_RX_DATA(x)		(((x) & 0xff) << 0)
71 #define RDA_UART_TX_DATA(x)		(((x) & 0xff) << 0)
72 
73 /* UART_IRQ_MASK Bits */
74 #define RDA_UART_TX_MODEM_STATUS	BIT(0)
75 #define RDA_UART_RX_DATA_AVAILABLE	BIT(1)
76 #define RDA_UART_TX_DATA_NEEDED		BIT(2)
77 #define RDA_UART_RX_TIMEOUT		BIT(3)
78 #define RDA_UART_RX_LINE_ERR		BIT(4)
79 #define RDA_UART_TX_DMA_DONE		BIT(5)
80 #define RDA_UART_RX_DMA_DONE		BIT(6)
81 #define RDA_UART_RX_DMA_TIMEOUT		BIT(7)
82 #define RDA_UART_DTR_RISE		BIT(8)
83 #define RDA_UART_DTR_FALL		BIT(9)
84 
85 /* UART_IRQ_CAUSE Bits */
86 #define RDA_UART_TX_MODEM_STATUS_U	BIT(16)
87 #define RDA_UART_RX_DATA_AVAILABLE_U	BIT(17)
88 #define RDA_UART_TX_DATA_NEEDED_U	BIT(18)
89 #define RDA_UART_RX_TIMEOUT_U		BIT(19)
90 #define RDA_UART_RX_LINE_ERR_U		BIT(20)
91 #define RDA_UART_TX_DMA_DONE_U		BIT(21)
92 #define RDA_UART_RX_DMA_DONE_U		BIT(22)
93 #define RDA_UART_RX_DMA_TIMEOUT_U	BIT(23)
94 #define RDA_UART_DTR_RISE_U		BIT(24)
95 #define RDA_UART_DTR_FALL_U		BIT(25)
96 
97 /* UART_TRIGGERS Bits */
98 #define RDA_UART_RX_TRIGGER(x)		(((x) & 0x1f) << 0)
99 #define RDA_UART_TX_TRIGGER(x)		(((x) & 0xf) << 8)
100 #define RDA_UART_AFC_LEVEL(x)		(((x) & 0x1f) << 16)
101 
102 /* UART_CMD_SET Bits */
103 #define RDA_UART_RI			BIT(0)
104 #define RDA_UART_DCD			BIT(1)
105 #define RDA_UART_DSR			BIT(2)
106 #define RDA_UART_TX_BREAK_CONTROL	BIT(3)
107 #define RDA_UART_TX_FINISH_N_WAIT	BIT(4)
108 #define RDA_UART_RTS			BIT(5)
109 #define RDA_UART_RX_FIFO_RESET		BIT(6)
110 #define RDA_UART_TX_FIFO_RESET		BIT(7)
111 
112 #define RDA_UART_TX_FIFO_SIZE	16
113 
114 static struct uart_driver rda_uart_driver;
115 
116 struct rda_uart_port {
117 	struct uart_port port;
118 	struct clk *clk;
119 };
120 
121 #define to_rda_uart_port(port) container_of(port, struct rda_uart_port, port)
122 
123 static struct rda_uart_port *rda_uart_ports[RDA_UART_PORT_NUM];
124 
rda_uart_write(struct uart_port * port,u32 val,unsigned int off)125 static inline void rda_uart_write(struct uart_port *port, u32 val,
126 				  unsigned int off)
127 {
128 	writel(val, port->membase + off);
129 }
130 
rda_uart_read(struct uart_port * port,unsigned int off)131 static inline u32 rda_uart_read(struct uart_port *port, unsigned int off)
132 {
133 	return readl(port->membase + off);
134 }
135 
rda_uart_tx_empty(struct uart_port * port)136 static unsigned int rda_uart_tx_empty(struct uart_port *port)
137 {
138 	unsigned long flags;
139 	unsigned int ret;
140 	u32 val;
141 
142 	spin_lock_irqsave(&port->lock, flags);
143 
144 	val = rda_uart_read(port, RDA_UART_STATUS);
145 	ret = (val & RDA_UART_TX_FIFO_MASK) ? TIOCSER_TEMT : 0;
146 
147 	spin_unlock_irqrestore(&port->lock, flags);
148 
149 	return ret;
150 }
151 
rda_uart_get_mctrl(struct uart_port * port)152 static unsigned int rda_uart_get_mctrl(struct uart_port *port)
153 {
154 	unsigned int mctrl = 0;
155 	u32 cmd_set, status;
156 
157 	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
158 	status = rda_uart_read(port, RDA_UART_STATUS);
159 	if (cmd_set & RDA_UART_RTS)
160 		mctrl |= TIOCM_RTS;
161 	if (!(status & RDA_UART_CTS))
162 		mctrl |= TIOCM_CTS;
163 
164 	return mctrl;
165 }
166 
rda_uart_set_mctrl(struct uart_port * port,unsigned int mctrl)167 static void rda_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
168 {
169 	u32 val;
170 
171 	if (mctrl & TIOCM_RTS) {
172 		val = rda_uart_read(port, RDA_UART_CMD_SET);
173 		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_SET);
174 	} else {
175 		/* Clear RTS to stop to receive. */
176 		val = rda_uart_read(port, RDA_UART_CMD_CLR);
177 		rda_uart_write(port, (val | RDA_UART_RTS), RDA_UART_CMD_CLR);
178 	}
179 
180 	val = rda_uart_read(port, RDA_UART_CTRL);
181 
182 	if (mctrl & TIOCM_LOOP)
183 		val |= RDA_UART_LOOP_BACK_EN;
184 	else
185 		val &= ~RDA_UART_LOOP_BACK_EN;
186 
187 	rda_uart_write(port, val, RDA_UART_CTRL);
188 }
189 
rda_uart_stop_tx(struct uart_port * port)190 static void rda_uart_stop_tx(struct uart_port *port)
191 {
192 	u32 val;
193 
194 	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
195 	val &= ~RDA_UART_TX_DATA_NEEDED;
196 	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
197 
198 	val = rda_uart_read(port, RDA_UART_CMD_SET);
199 	val |= RDA_UART_TX_FIFO_RESET;
200 	rda_uart_write(port, val, RDA_UART_CMD_SET);
201 }
202 
rda_uart_stop_rx(struct uart_port * port)203 static void rda_uart_stop_rx(struct uart_port *port)
204 {
205 	u32 val;
206 
207 	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
208 	val &= ~(RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
209 	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
210 
211 	/* Read Rx buffer before reset to avoid Rx timeout interrupt */
212 	val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
213 
214 	val = rda_uart_read(port, RDA_UART_CMD_SET);
215 	val |= RDA_UART_RX_FIFO_RESET;
216 	rda_uart_write(port, val, RDA_UART_CMD_SET);
217 }
218 
rda_uart_start_tx(struct uart_port * port)219 static void rda_uart_start_tx(struct uart_port *port)
220 {
221 	u32 val;
222 
223 	if (uart_tx_stopped(port)) {
224 		rda_uart_stop_tx(port);
225 		return;
226 	}
227 
228 	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
229 	val |= RDA_UART_TX_DATA_NEEDED;
230 	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
231 }
232 
rda_uart_change_baudrate(struct rda_uart_port * rda_port,unsigned long baud)233 static void rda_uart_change_baudrate(struct rda_uart_port *rda_port,
234 				     unsigned long baud)
235 {
236 	clk_set_rate(rda_port->clk, baud * 8);
237 }
238 
rda_uart_set_termios(struct uart_port * port,struct ktermios * termios,struct ktermios * old)239 static void rda_uart_set_termios(struct uart_port *port,
240 				 struct ktermios *termios,
241 				 struct ktermios *old)
242 {
243 	struct rda_uart_port *rda_port = to_rda_uart_port(port);
244 	unsigned long flags;
245 	unsigned int ctrl, cmd_set, cmd_clr, triggers;
246 	unsigned int baud;
247 	u32 irq_mask;
248 
249 	spin_lock_irqsave(&port->lock, flags);
250 
251 	baud = uart_get_baud_rate(port, termios, old, 9600, port->uartclk / 4);
252 	rda_uart_change_baudrate(rda_port, baud);
253 
254 	ctrl = rda_uart_read(port, RDA_UART_CTRL);
255 	cmd_set = rda_uart_read(port, RDA_UART_CMD_SET);
256 	cmd_clr = rda_uart_read(port, RDA_UART_CMD_CLR);
257 
258 	switch (termios->c_cflag & CSIZE) {
259 	case CS5:
260 	case CS6:
261 		dev_warn(port->dev, "bit size not supported, using 7 bits\n");
262 		fallthrough;
263 	case CS7:
264 		ctrl &= ~RDA_UART_DBITS_8;
265 		termios->c_cflag &= ~CSIZE;
266 		termios->c_cflag |= CS7;
267 		break;
268 	default:
269 		ctrl |= RDA_UART_DBITS_8;
270 		break;
271 	}
272 
273 	/* stop bits */
274 	if (termios->c_cflag & CSTOPB)
275 		ctrl |= RDA_UART_TX_SBITS_2;
276 	else
277 		ctrl &= ~RDA_UART_TX_SBITS_2;
278 
279 	/* parity check */
280 	if (termios->c_cflag & PARENB) {
281 		ctrl |= RDA_UART_PARITY_EN;
282 
283 		/* Mark or Space parity */
284 		if (termios->c_cflag & CMSPAR) {
285 			if (termios->c_cflag & PARODD)
286 				ctrl |= RDA_UART_PARITY_MARK;
287 			else
288 				ctrl |= RDA_UART_PARITY_SPACE;
289 		} else if (termios->c_cflag & PARODD) {
290 			ctrl |= RDA_UART_PARITY_ODD;
291 		} else {
292 			ctrl |= RDA_UART_PARITY_EVEN;
293 		}
294 	} else {
295 		ctrl &= ~RDA_UART_PARITY_EN;
296 	}
297 
298 	/* Hardware handshake (RTS/CTS) */
299 	if (termios->c_cflag & CRTSCTS) {
300 		ctrl   |= RDA_UART_FLOW_CNT_EN;
301 		cmd_set |= RDA_UART_RTS;
302 	} else {
303 		ctrl   &= ~RDA_UART_FLOW_CNT_EN;
304 		cmd_clr |= RDA_UART_RTS;
305 	}
306 
307 	ctrl |= RDA_UART_ENABLE;
308 	ctrl &= ~RDA_UART_DMA_EN;
309 
310 	triggers  = (RDA_UART_AFC_LEVEL(20) | RDA_UART_RX_TRIGGER(16));
311 	irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
312 	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
313 
314 	rda_uart_write(port, triggers, RDA_UART_IRQ_TRIGGERS);
315 	rda_uart_write(port, ctrl, RDA_UART_CTRL);
316 	rda_uart_write(port, cmd_set, RDA_UART_CMD_SET);
317 	rda_uart_write(port, cmd_clr, RDA_UART_CMD_CLR);
318 
319 	rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
320 
321 	/* Don't rewrite B0 */
322 	if (tty_termios_baud_rate(termios))
323 		tty_termios_encode_baud_rate(termios, baud, baud);
324 
325 	/* update the per-port timeout */
326 	uart_update_timeout(port, termios->c_cflag, baud);
327 
328 	spin_unlock_irqrestore(&port->lock, flags);
329 }
330 
rda_uart_send_chars(struct uart_port * port)331 static void rda_uart_send_chars(struct uart_port *port)
332 {
333 	struct circ_buf *xmit = &port->state->xmit;
334 	unsigned int ch;
335 	u32 val;
336 
337 	if (uart_tx_stopped(port))
338 		return;
339 
340 	if (port->x_char) {
341 		while (!(rda_uart_read(port, RDA_UART_STATUS) &
342 			 RDA_UART_TX_FIFO_MASK))
343 			cpu_relax();
344 
345 		rda_uart_write(port, port->x_char, RDA_UART_RXTX_BUFFER);
346 		port->icount.tx++;
347 		port->x_char = 0;
348 	}
349 
350 	while (rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK) {
351 		if (uart_circ_empty(xmit))
352 			break;
353 
354 		ch = xmit->buf[xmit->tail];
355 		rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
356 		xmit->tail = (xmit->tail + 1) & (SERIAL_XMIT_SIZE - 1);
357 		port->icount.tx++;
358 	}
359 
360 	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
361 		uart_write_wakeup(port);
362 
363 	if (!uart_circ_empty(xmit)) {
364 		/* Re-enable Tx FIFO interrupt */
365 		val = rda_uart_read(port, RDA_UART_IRQ_MASK);
366 		val |= RDA_UART_TX_DATA_NEEDED;
367 		rda_uart_write(port, val, RDA_UART_IRQ_MASK);
368 	}
369 }
370 
rda_uart_receive_chars(struct uart_port * port)371 static void rda_uart_receive_chars(struct uart_port *port)
372 {
373 	u32 status, val;
374 
375 	status = rda_uart_read(port, RDA_UART_STATUS);
376 	while ((status & RDA_UART_RX_FIFO_MASK)) {
377 		char flag = TTY_NORMAL;
378 
379 		if (status & RDA_UART_RX_PARITY_ERR) {
380 			port->icount.parity++;
381 			flag = TTY_PARITY;
382 		}
383 
384 		if (status & RDA_UART_RX_FRAMING_ERR) {
385 			port->icount.frame++;
386 			flag = TTY_FRAME;
387 		}
388 
389 		if (status & RDA_UART_RX_OVERFLOW_ERR) {
390 			port->icount.overrun++;
391 			flag = TTY_OVERRUN;
392 		}
393 
394 		val = rda_uart_read(port, RDA_UART_RXTX_BUFFER);
395 		val &= 0xff;
396 
397 		port->icount.rx++;
398 		tty_insert_flip_char(&port->state->port, val, flag);
399 
400 		status = rda_uart_read(port, RDA_UART_STATUS);
401 	}
402 
403 	tty_flip_buffer_push(&port->state->port);
404 }
405 
rda_interrupt(int irq,void * dev_id)406 static irqreturn_t rda_interrupt(int irq, void *dev_id)
407 {
408 	struct uart_port *port = dev_id;
409 	unsigned long flags;
410 	u32 val, irq_mask;
411 
412 	spin_lock_irqsave(&port->lock, flags);
413 
414 	/* Clear IRQ cause */
415 	val = rda_uart_read(port, RDA_UART_IRQ_CAUSE);
416 	rda_uart_write(port, val, RDA_UART_IRQ_CAUSE);
417 
418 	if (val & (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT))
419 		rda_uart_receive_chars(port);
420 
421 	if (val & (RDA_UART_TX_DATA_NEEDED)) {
422 		irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
423 		irq_mask &= ~RDA_UART_TX_DATA_NEEDED;
424 		rda_uart_write(port, irq_mask, RDA_UART_IRQ_MASK);
425 
426 		rda_uart_send_chars(port);
427 	}
428 
429 	spin_unlock_irqrestore(&port->lock, flags);
430 
431 	return IRQ_HANDLED;
432 }
433 
rda_uart_startup(struct uart_port * port)434 static int rda_uart_startup(struct uart_port *port)
435 {
436 	unsigned long flags;
437 	int ret;
438 	u32 val;
439 
440 	spin_lock_irqsave(&port->lock, flags);
441 	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
442 	spin_unlock_irqrestore(&port->lock, flags);
443 
444 	ret = request_irq(port->irq, rda_interrupt, IRQF_NO_SUSPEND,
445 			  "rda-uart", port);
446 	if (ret)
447 		return ret;
448 
449 	spin_lock_irqsave(&port->lock, flags);
450 
451 	val = rda_uart_read(port, RDA_UART_CTRL);
452 	val |= RDA_UART_ENABLE;
453 	rda_uart_write(port, val, RDA_UART_CTRL);
454 
455 	/* enable rx interrupt */
456 	val = rda_uart_read(port, RDA_UART_IRQ_MASK);
457 	val |= (RDA_UART_RX_DATA_AVAILABLE | RDA_UART_RX_TIMEOUT);
458 	rda_uart_write(port, val, RDA_UART_IRQ_MASK);
459 
460 	spin_unlock_irqrestore(&port->lock, flags);
461 
462 	return 0;
463 }
464 
rda_uart_shutdown(struct uart_port * port)465 static void rda_uart_shutdown(struct uart_port *port)
466 {
467 	unsigned long flags;
468 	u32 val;
469 
470 	spin_lock_irqsave(&port->lock, flags);
471 
472 	rda_uart_stop_tx(port);
473 	rda_uart_stop_rx(port);
474 
475 	val = rda_uart_read(port, RDA_UART_CTRL);
476 	val &= ~RDA_UART_ENABLE;
477 	rda_uart_write(port, val, RDA_UART_CTRL);
478 
479 	spin_unlock_irqrestore(&port->lock, flags);
480 }
481 
rda_uart_type(struct uart_port * port)482 static const char *rda_uart_type(struct uart_port *port)
483 {
484 	return (port->type == PORT_RDA) ? "rda-uart" : NULL;
485 }
486 
rda_uart_request_port(struct uart_port * port)487 static int rda_uart_request_port(struct uart_port *port)
488 {
489 	struct platform_device *pdev = to_platform_device(port->dev);
490 	struct resource *res;
491 
492 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
493 	if (!res)
494 		return -ENXIO;
495 
496 	if (!devm_request_mem_region(port->dev, port->mapbase,
497 				     resource_size(res), dev_name(port->dev)))
498 		return -EBUSY;
499 
500 	if (port->flags & UPF_IOREMAP) {
501 		port->membase = devm_ioremap(port->dev, port->mapbase,
502 						     resource_size(res));
503 		if (!port->membase)
504 			return -EBUSY;
505 	}
506 
507 	return 0;
508 }
509 
rda_uart_config_port(struct uart_port * port,int flags)510 static void rda_uart_config_port(struct uart_port *port, int flags)
511 {
512 	unsigned long irq_flags;
513 
514 	if (flags & UART_CONFIG_TYPE) {
515 		port->type = PORT_RDA;
516 		rda_uart_request_port(port);
517 	}
518 
519 	spin_lock_irqsave(&port->lock, irq_flags);
520 
521 	/* Clear mask, so no surprise interrupts. */
522 	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
523 
524 	/* Clear status register */
525 	rda_uart_write(port, 0, RDA_UART_STATUS);
526 
527 	spin_unlock_irqrestore(&port->lock, irq_flags);
528 }
529 
rda_uart_release_port(struct uart_port * port)530 static void rda_uart_release_port(struct uart_port *port)
531 {
532 	struct platform_device *pdev = to_platform_device(port->dev);
533 	struct resource *res;
534 
535 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
536 	if (!res)
537 		return;
538 
539 	if (port->flags & UPF_IOREMAP) {
540 		devm_release_mem_region(port->dev, port->mapbase,
541 					resource_size(res));
542 		devm_iounmap(port->dev, port->membase);
543 		port->membase = NULL;
544 	}
545 }
546 
rda_uart_verify_port(struct uart_port * port,struct serial_struct * ser)547 static int rda_uart_verify_port(struct uart_port *port,
548 				struct serial_struct *ser)
549 {
550 	if (port->type != PORT_RDA)
551 		return -EINVAL;
552 
553 	if (port->irq != ser->irq)
554 		return -EINVAL;
555 
556 	return 0;
557 }
558 
559 static const struct uart_ops rda_uart_ops = {
560 	.tx_empty       = rda_uart_tx_empty,
561 	.get_mctrl      = rda_uart_get_mctrl,
562 	.set_mctrl      = rda_uart_set_mctrl,
563 	.start_tx       = rda_uart_start_tx,
564 	.stop_tx        = rda_uart_stop_tx,
565 	.stop_rx        = rda_uart_stop_rx,
566 	.startup        = rda_uart_startup,
567 	.shutdown       = rda_uart_shutdown,
568 	.set_termios    = rda_uart_set_termios,
569 	.type           = rda_uart_type,
570 	.request_port	= rda_uart_request_port,
571 	.release_port	= rda_uart_release_port,
572 	.config_port	= rda_uart_config_port,
573 	.verify_port	= rda_uart_verify_port,
574 };
575 
576 #ifdef CONFIG_SERIAL_RDA_CONSOLE
577 
rda_console_putchar(struct uart_port * port,unsigned char ch)578 static void rda_console_putchar(struct uart_port *port, unsigned char ch)
579 {
580 	if (!port->membase)
581 		return;
582 
583 	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
584 		cpu_relax();
585 
586 	rda_uart_write(port, ch, RDA_UART_RXTX_BUFFER);
587 }
588 
rda_uart_port_write(struct uart_port * port,const char * s,u_int count)589 static void rda_uart_port_write(struct uart_port *port, const char *s,
590 				u_int count)
591 {
592 	u32 old_irq_mask;
593 	unsigned long flags;
594 	int locked;
595 
596 	local_irq_save(flags);
597 
598 	if (port->sysrq) {
599 		locked = 0;
600 	} else if (oops_in_progress) {
601 		locked = spin_trylock(&port->lock);
602 	} else {
603 		spin_lock(&port->lock);
604 		locked = 1;
605 	}
606 
607 	old_irq_mask = rda_uart_read(port, RDA_UART_IRQ_MASK);
608 	rda_uart_write(port, 0, RDA_UART_IRQ_MASK);
609 
610 	uart_console_write(port, s, count, rda_console_putchar);
611 
612 	/* wait until all contents have been sent out */
613 	while (!(rda_uart_read(port, RDA_UART_STATUS) & RDA_UART_TX_FIFO_MASK))
614 		cpu_relax();
615 
616 	rda_uart_write(port, old_irq_mask, RDA_UART_IRQ_MASK);
617 
618 	if (locked)
619 		spin_unlock(&port->lock);
620 
621 	local_irq_restore(flags);
622 }
623 
rda_uart_console_write(struct console * co,const char * s,u_int count)624 static void rda_uart_console_write(struct console *co, const char *s,
625 				   u_int count)
626 {
627 	struct rda_uart_port *rda_port;
628 
629 	rda_port = rda_uart_ports[co->index];
630 	if (!rda_port)
631 		return;
632 
633 	rda_uart_port_write(&rda_port->port, s, count);
634 }
635 
rda_uart_console_setup(struct console * co,char * options)636 static int rda_uart_console_setup(struct console *co, char *options)
637 {
638 	struct rda_uart_port *rda_port;
639 	int baud = 921600;
640 	int bits = 8;
641 	int parity = 'n';
642 	int flow = 'n';
643 
644 	if (co->index < 0 || co->index >= RDA_UART_PORT_NUM)
645 		return -EINVAL;
646 
647 	rda_port = rda_uart_ports[co->index];
648 	if (!rda_port || !rda_port->port.membase)
649 		return -ENODEV;
650 
651 	if (options)
652 		uart_parse_options(options, &baud, &parity, &bits, &flow);
653 
654 	return uart_set_options(&rda_port->port, co, baud, parity, bits, flow);
655 }
656 
657 static struct console rda_uart_console = {
658 	.name = RDA_UART_DEV_NAME,
659 	.write = rda_uart_console_write,
660 	.device = uart_console_device,
661 	.setup = rda_uart_console_setup,
662 	.flags = CON_PRINTBUFFER,
663 	.index = -1,
664 	.data = &rda_uart_driver,
665 };
666 
rda_uart_console_init(void)667 static int __init rda_uart_console_init(void)
668 {
669 	register_console(&rda_uart_console);
670 
671 	return 0;
672 }
673 console_initcall(rda_uart_console_init);
674 
rda_uart_early_console_write(struct console * co,const char * s,u_int count)675 static void rda_uart_early_console_write(struct console *co,
676 					 const char *s,
677 					 u_int count)
678 {
679 	struct earlycon_device *dev = co->data;
680 
681 	rda_uart_port_write(&dev->port, s, count);
682 }
683 
684 static int __init
rda_uart_early_console_setup(struct earlycon_device * device,const char * opt)685 rda_uart_early_console_setup(struct earlycon_device *device, const char *opt)
686 {
687 	if (!device->port.membase)
688 		return -ENODEV;
689 
690 	device->con->write = rda_uart_early_console_write;
691 
692 	return 0;
693 }
694 
695 OF_EARLYCON_DECLARE(rda, "rda,8810pl-uart",
696 		    rda_uart_early_console_setup);
697 
698 #define RDA_UART_CONSOLE (&rda_uart_console)
699 #else
700 #define RDA_UART_CONSOLE NULL
701 #endif /* CONFIG_SERIAL_RDA_CONSOLE */
702 
703 static struct uart_driver rda_uart_driver = {
704 	.owner = THIS_MODULE,
705 	.driver_name = "rda-uart",
706 	.dev_name = RDA_UART_DEV_NAME,
707 	.nr = RDA_UART_PORT_NUM,
708 	.cons = RDA_UART_CONSOLE,
709 };
710 
711 static const struct of_device_id rda_uart_dt_matches[] = {
712 	{ .compatible = "rda,8810pl-uart" },
713 	{ }
714 };
715 MODULE_DEVICE_TABLE(of, rda_uart_dt_matches);
716 
rda_uart_probe(struct platform_device * pdev)717 static int rda_uart_probe(struct platform_device *pdev)
718 {
719 	struct resource *res_mem;
720 	struct rda_uart_port *rda_port;
721 	int ret, irq;
722 
723 	if (pdev->dev.of_node)
724 		pdev->id = of_alias_get_id(pdev->dev.of_node, "serial");
725 
726 	if (pdev->id < 0 || pdev->id >= RDA_UART_PORT_NUM) {
727 		dev_err(&pdev->dev, "id %d out of range\n", pdev->id);
728 		return -EINVAL;
729 	}
730 
731 	res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
732 	if (!res_mem) {
733 		dev_err(&pdev->dev, "could not get mem\n");
734 		return -ENODEV;
735 	}
736 
737 	irq = platform_get_irq(pdev, 0);
738 	if (irq < 0)
739 		return irq;
740 
741 	if (rda_uart_ports[pdev->id]) {
742 		dev_err(&pdev->dev, "port %d already allocated\n", pdev->id);
743 		return -EBUSY;
744 	}
745 
746 	rda_port = devm_kzalloc(&pdev->dev, sizeof(*rda_port), GFP_KERNEL);
747 	if (!rda_port)
748 		return -ENOMEM;
749 
750 	rda_port->clk = devm_clk_get(&pdev->dev, NULL);
751 	if (IS_ERR(rda_port->clk)) {
752 		dev_err(&pdev->dev, "could not get clk\n");
753 		return PTR_ERR(rda_port->clk);
754 	}
755 
756 	rda_port->port.dev = &pdev->dev;
757 	rda_port->port.regshift = 0;
758 	rda_port->port.line = pdev->id;
759 	rda_port->port.type = PORT_RDA;
760 	rda_port->port.iotype = UPIO_MEM;
761 	rda_port->port.mapbase = res_mem->start;
762 	rda_port->port.irq = irq;
763 	rda_port->port.uartclk = clk_get_rate(rda_port->clk);
764 	if (rda_port->port.uartclk == 0) {
765 		dev_err(&pdev->dev, "clock rate is zero\n");
766 		return -EINVAL;
767 	}
768 	rda_port->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP |
769 			       UPF_LOW_LATENCY;
770 	rda_port->port.x_char = 0;
771 	rda_port->port.fifosize = RDA_UART_TX_FIFO_SIZE;
772 	rda_port->port.ops = &rda_uart_ops;
773 
774 	rda_uart_ports[pdev->id] = rda_port;
775 	platform_set_drvdata(pdev, rda_port);
776 
777 	ret = uart_add_one_port(&rda_uart_driver, &rda_port->port);
778 	if (ret)
779 		rda_uart_ports[pdev->id] = NULL;
780 
781 	return ret;
782 }
783 
rda_uart_remove(struct platform_device * pdev)784 static int rda_uart_remove(struct platform_device *pdev)
785 {
786 	struct rda_uart_port *rda_port = platform_get_drvdata(pdev);
787 
788 	uart_remove_one_port(&rda_uart_driver, &rda_port->port);
789 	rda_uart_ports[pdev->id] = NULL;
790 
791 	return 0;
792 }
793 
794 static struct platform_driver rda_uart_platform_driver = {
795 	.probe = rda_uart_probe,
796 	.remove = rda_uart_remove,
797 	.driver = {
798 		.name = "rda-uart",
799 		.of_match_table = rda_uart_dt_matches,
800 	},
801 };
802 
rda_uart_init(void)803 static int __init rda_uart_init(void)
804 {
805 	int ret;
806 
807 	ret = uart_register_driver(&rda_uart_driver);
808 	if (ret)
809 		return ret;
810 
811 	ret = platform_driver_register(&rda_uart_platform_driver);
812 	if (ret)
813 		uart_unregister_driver(&rda_uart_driver);
814 
815 	return ret;
816 }
817 
rda_uart_exit(void)818 static void __exit rda_uart_exit(void)
819 {
820 	platform_driver_unregister(&rda_uart_platform_driver);
821 	uart_unregister_driver(&rda_uart_driver);
822 }
823 
824 module_init(rda_uart_init);
825 module_exit(rda_uart_exit);
826 
827 MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>");
828 MODULE_DESCRIPTION("RDA8810PL serial device driver");
829 MODULE_LICENSE("GPL");
830