1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2012 Texas Instruments
4 * Author: Rob Clark <robdclark@gmail.com>
5 */
6
7 #include <linux/component.h>
8 #include <linux/gpio/consumer.h>
9 #include <linux/hdmi.h>
10 #include <linux/module.h>
11 #include <linux/platform_data/tda9950.h>
12 #include <linux/irq.h>
13 #include <sound/asoundef.h>
14 #include <sound/hdmi-codec.h>
15
16 #include <drm/drm_atomic_helper.h>
17 #include <drm/drm_bridge.h>
18 #include <drm/drm_edid.h>
19 #include <drm/drm_of.h>
20 #include <drm/drm_print.h>
21 #include <drm/drm_probe_helper.h>
22 #include <drm/drm_simple_kms_helper.h>
23 #include <drm/i2c/tda998x.h>
24
25 #include <media/cec-notifier.h>
26
27 #define DBG(fmt, ...) DRM_DEBUG(fmt"\n", ##__VA_ARGS__)
28
29 enum {
30 AUDIO_ROUTE_I2S,
31 AUDIO_ROUTE_SPDIF,
32 AUDIO_ROUTE_NUM
33 };
34
35 struct tda998x_audio_route {
36 u8 ena_aclk;
37 u8 mux_ap;
38 u8 aip_clksel;
39 };
40
41 struct tda998x_audio_settings {
42 const struct tda998x_audio_route *route;
43 struct hdmi_audio_infoframe cea;
44 unsigned int sample_rate;
45 u8 status[5];
46 u8 ena_ap;
47 u8 i2s_format;
48 u8 cts_n;
49 };
50
51 struct tda998x_priv {
52 struct i2c_client *cec;
53 struct i2c_client *hdmi;
54 struct mutex mutex;
55 u16 rev;
56 u8 cec_addr;
57 u8 current_page;
58 bool is_on;
59 bool supports_infoframes;
60 bool sink_has_audio;
61 enum hdmi_quantization_range rgb_quant_range;
62 u8 vip_cntrl_0;
63 u8 vip_cntrl_1;
64 u8 vip_cntrl_2;
65 unsigned long tmds_clock;
66 struct tda998x_audio_settings audio;
67
68 struct platform_device *audio_pdev;
69 struct mutex audio_mutex;
70
71 struct mutex edid_mutex;
72 wait_queue_head_t wq_edid;
73 volatile int wq_edid_wait;
74
75 struct work_struct detect_work;
76 struct timer_list edid_delay_timer;
77 wait_queue_head_t edid_delay_waitq;
78 bool edid_delay_active;
79
80 struct drm_encoder encoder;
81 struct drm_bridge bridge;
82 struct drm_connector connector;
83
84 u8 audio_port_enable[AUDIO_ROUTE_NUM];
85 struct tda9950_glue cec_glue;
86 struct gpio_desc *calib;
87 struct cec_notifier *cec_notify;
88 };
89
90 #define conn_to_tda998x_priv(x) \
91 container_of(x, struct tda998x_priv, connector)
92 #define enc_to_tda998x_priv(x) \
93 container_of(x, struct tda998x_priv, encoder)
94 #define bridge_to_tda998x_priv(x) \
95 container_of(x, struct tda998x_priv, bridge)
96
97 /* The TDA9988 series of devices use a paged register scheme.. to simplify
98 * things we encode the page # in upper bits of the register #. To read/
99 * write a given register, we need to make sure CURPAGE register is set
100 * appropriately. Which implies reads/writes are not atomic. Fun!
101 */
102
103 #define REG(page, addr) (((page) << 8) | (addr))
104 #define REG2ADDR(reg) ((reg) & 0xff)
105 #define REG2PAGE(reg) (((reg) >> 8) & 0xff)
106
107 #define REG_CURPAGE 0xff /* write */
108
109
110 /* Page 00h: General Control */
111 #define REG_VERSION_LSB REG(0x00, 0x00) /* read */
112 #define REG_MAIN_CNTRL0 REG(0x00, 0x01) /* read/write */
113 # define MAIN_CNTRL0_SR (1 << 0)
114 # define MAIN_CNTRL0_DECS (1 << 1)
115 # define MAIN_CNTRL0_DEHS (1 << 2)
116 # define MAIN_CNTRL0_CECS (1 << 3)
117 # define MAIN_CNTRL0_CEHS (1 << 4)
118 # define MAIN_CNTRL0_SCALER (1 << 7)
119 #define REG_VERSION_MSB REG(0x00, 0x02) /* read */
120 #define REG_SOFTRESET REG(0x00, 0x0a) /* write */
121 # define SOFTRESET_AUDIO (1 << 0)
122 # define SOFTRESET_I2C_MASTER (1 << 1)
123 #define REG_DDC_DISABLE REG(0x00, 0x0b) /* read/write */
124 #define REG_CCLK_ON REG(0x00, 0x0c) /* read/write */
125 #define REG_I2C_MASTER REG(0x00, 0x0d) /* read/write */
126 # define I2C_MASTER_DIS_MM (1 << 0)
127 # define I2C_MASTER_DIS_FILT (1 << 1)
128 # define I2C_MASTER_APP_STRT_LAT (1 << 2)
129 #define REG_FEAT_POWERDOWN REG(0x00, 0x0e) /* read/write */
130 # define FEAT_POWERDOWN_PREFILT BIT(0)
131 # define FEAT_POWERDOWN_CSC BIT(1)
132 # define FEAT_POWERDOWN_SPDIF (1 << 3)
133 #define REG_INT_FLAGS_0 REG(0x00, 0x0f) /* read/write */
134 #define REG_INT_FLAGS_1 REG(0x00, 0x10) /* read/write */
135 #define REG_INT_FLAGS_2 REG(0x00, 0x11) /* read/write */
136 # define INT_FLAGS_2_EDID_BLK_RD (1 << 1)
137 #define REG_ENA_ACLK REG(0x00, 0x16) /* read/write */
138 #define REG_ENA_VP_0 REG(0x00, 0x18) /* read/write */
139 #define REG_ENA_VP_1 REG(0x00, 0x19) /* read/write */
140 #define REG_ENA_VP_2 REG(0x00, 0x1a) /* read/write */
141 #define REG_ENA_AP REG(0x00, 0x1e) /* read/write */
142 #define REG_VIP_CNTRL_0 REG(0x00, 0x20) /* write */
143 # define VIP_CNTRL_0_MIRR_A (1 << 7)
144 # define VIP_CNTRL_0_SWAP_A(x) (((x) & 7) << 4)
145 # define VIP_CNTRL_0_MIRR_B (1 << 3)
146 # define VIP_CNTRL_0_SWAP_B(x) (((x) & 7) << 0)
147 #define REG_VIP_CNTRL_1 REG(0x00, 0x21) /* write */
148 # define VIP_CNTRL_1_MIRR_C (1 << 7)
149 # define VIP_CNTRL_1_SWAP_C(x) (((x) & 7) << 4)
150 # define VIP_CNTRL_1_MIRR_D (1 << 3)
151 # define VIP_CNTRL_1_SWAP_D(x) (((x) & 7) << 0)
152 #define REG_VIP_CNTRL_2 REG(0x00, 0x22) /* write */
153 # define VIP_CNTRL_2_MIRR_E (1 << 7)
154 # define VIP_CNTRL_2_SWAP_E(x) (((x) & 7) << 4)
155 # define VIP_CNTRL_2_MIRR_F (1 << 3)
156 # define VIP_CNTRL_2_SWAP_F(x) (((x) & 7) << 0)
157 #define REG_VIP_CNTRL_3 REG(0x00, 0x23) /* write */
158 # define VIP_CNTRL_3_X_TGL (1 << 0)
159 # define VIP_CNTRL_3_H_TGL (1 << 1)
160 # define VIP_CNTRL_3_V_TGL (1 << 2)
161 # define VIP_CNTRL_3_EMB (1 << 3)
162 # define VIP_CNTRL_3_SYNC_DE (1 << 4)
163 # define VIP_CNTRL_3_SYNC_HS (1 << 5)
164 # define VIP_CNTRL_3_DE_INT (1 << 6)
165 # define VIP_CNTRL_3_EDGE (1 << 7)
166 #define REG_VIP_CNTRL_4 REG(0x00, 0x24) /* write */
167 # define VIP_CNTRL_4_BLC(x) (((x) & 3) << 0)
168 # define VIP_CNTRL_4_BLANKIT(x) (((x) & 3) << 2)
169 # define VIP_CNTRL_4_CCIR656 (1 << 4)
170 # define VIP_CNTRL_4_656_ALT (1 << 5)
171 # define VIP_CNTRL_4_TST_656 (1 << 6)
172 # define VIP_CNTRL_4_TST_PAT (1 << 7)
173 #define REG_VIP_CNTRL_5 REG(0x00, 0x25) /* write */
174 # define VIP_CNTRL_5_CKCASE (1 << 0)
175 # define VIP_CNTRL_5_SP_CNT(x) (((x) & 3) << 1)
176 #define REG_MUX_AP REG(0x00, 0x26) /* read/write */
177 # define MUX_AP_SELECT_I2S 0x64
178 # define MUX_AP_SELECT_SPDIF 0x40
179 #define REG_MUX_VP_VIP_OUT REG(0x00, 0x27) /* read/write */
180 #define REG_MAT_CONTRL REG(0x00, 0x80) /* write */
181 # define MAT_CONTRL_MAT_SC(x) (((x) & 3) << 0)
182 # define MAT_CONTRL_MAT_BP (1 << 2)
183 #define REG_VIDFORMAT REG(0x00, 0xa0) /* write */
184 #define REG_REFPIX_MSB REG(0x00, 0xa1) /* write */
185 #define REG_REFPIX_LSB REG(0x00, 0xa2) /* write */
186 #define REG_REFLINE_MSB REG(0x00, 0xa3) /* write */
187 #define REG_REFLINE_LSB REG(0x00, 0xa4) /* write */
188 #define REG_NPIX_MSB REG(0x00, 0xa5) /* write */
189 #define REG_NPIX_LSB REG(0x00, 0xa6) /* write */
190 #define REG_NLINE_MSB REG(0x00, 0xa7) /* write */
191 #define REG_NLINE_LSB REG(0x00, 0xa8) /* write */
192 #define REG_VS_LINE_STRT_1_MSB REG(0x00, 0xa9) /* write */
193 #define REG_VS_LINE_STRT_1_LSB REG(0x00, 0xaa) /* write */
194 #define REG_VS_PIX_STRT_1_MSB REG(0x00, 0xab) /* write */
195 #define REG_VS_PIX_STRT_1_LSB REG(0x00, 0xac) /* write */
196 #define REG_VS_LINE_END_1_MSB REG(0x00, 0xad) /* write */
197 #define REG_VS_LINE_END_1_LSB REG(0x00, 0xae) /* write */
198 #define REG_VS_PIX_END_1_MSB REG(0x00, 0xaf) /* write */
199 #define REG_VS_PIX_END_1_LSB REG(0x00, 0xb0) /* write */
200 #define REG_VS_LINE_STRT_2_MSB REG(0x00, 0xb1) /* write */
201 #define REG_VS_LINE_STRT_2_LSB REG(0x00, 0xb2) /* write */
202 #define REG_VS_PIX_STRT_2_MSB REG(0x00, 0xb3) /* write */
203 #define REG_VS_PIX_STRT_2_LSB REG(0x00, 0xb4) /* write */
204 #define REG_VS_LINE_END_2_MSB REG(0x00, 0xb5) /* write */
205 #define REG_VS_LINE_END_2_LSB REG(0x00, 0xb6) /* write */
206 #define REG_VS_PIX_END_2_MSB REG(0x00, 0xb7) /* write */
207 #define REG_VS_PIX_END_2_LSB REG(0x00, 0xb8) /* write */
208 #define REG_HS_PIX_START_MSB REG(0x00, 0xb9) /* write */
209 #define REG_HS_PIX_START_LSB REG(0x00, 0xba) /* write */
210 #define REG_HS_PIX_STOP_MSB REG(0x00, 0xbb) /* write */
211 #define REG_HS_PIX_STOP_LSB REG(0x00, 0xbc) /* write */
212 #define REG_VWIN_START_1_MSB REG(0x00, 0xbd) /* write */
213 #define REG_VWIN_START_1_LSB REG(0x00, 0xbe) /* write */
214 #define REG_VWIN_END_1_MSB REG(0x00, 0xbf) /* write */
215 #define REG_VWIN_END_1_LSB REG(0x00, 0xc0) /* write */
216 #define REG_VWIN_START_2_MSB REG(0x00, 0xc1) /* write */
217 #define REG_VWIN_START_2_LSB REG(0x00, 0xc2) /* write */
218 #define REG_VWIN_END_2_MSB REG(0x00, 0xc3) /* write */
219 #define REG_VWIN_END_2_LSB REG(0x00, 0xc4) /* write */
220 #define REG_DE_START_MSB REG(0x00, 0xc5) /* write */
221 #define REG_DE_START_LSB REG(0x00, 0xc6) /* write */
222 #define REG_DE_STOP_MSB REG(0x00, 0xc7) /* write */
223 #define REG_DE_STOP_LSB REG(0x00, 0xc8) /* write */
224 #define REG_TBG_CNTRL_0 REG(0x00, 0xca) /* write */
225 # define TBG_CNTRL_0_TOP_TGL (1 << 0)
226 # define TBG_CNTRL_0_TOP_SEL (1 << 1)
227 # define TBG_CNTRL_0_DE_EXT (1 << 2)
228 # define TBG_CNTRL_0_TOP_EXT (1 << 3)
229 # define TBG_CNTRL_0_FRAME_DIS (1 << 5)
230 # define TBG_CNTRL_0_SYNC_MTHD (1 << 6)
231 # define TBG_CNTRL_0_SYNC_ONCE (1 << 7)
232 #define REG_TBG_CNTRL_1 REG(0x00, 0xcb) /* write */
233 # define TBG_CNTRL_1_H_TGL (1 << 0)
234 # define TBG_CNTRL_1_V_TGL (1 << 1)
235 # define TBG_CNTRL_1_TGL_EN (1 << 2)
236 # define TBG_CNTRL_1_X_EXT (1 << 3)
237 # define TBG_CNTRL_1_H_EXT (1 << 4)
238 # define TBG_CNTRL_1_V_EXT (1 << 5)
239 # define TBG_CNTRL_1_DWIN_DIS (1 << 6)
240 #define REG_ENABLE_SPACE REG(0x00, 0xd6) /* write */
241 #define REG_HVF_CNTRL_0 REG(0x00, 0xe4) /* write */
242 # define HVF_CNTRL_0_SM (1 << 7)
243 # define HVF_CNTRL_0_RWB (1 << 6)
244 # define HVF_CNTRL_0_PREFIL(x) (((x) & 3) << 2)
245 # define HVF_CNTRL_0_INTPOL(x) (((x) & 3) << 0)
246 #define REG_HVF_CNTRL_1 REG(0x00, 0xe5) /* write */
247 # define HVF_CNTRL_1_FOR (1 << 0)
248 # define HVF_CNTRL_1_YUVBLK (1 << 1)
249 # define HVF_CNTRL_1_VQR(x) (((x) & 3) << 2)
250 # define HVF_CNTRL_1_PAD(x) (((x) & 3) << 4)
251 # define HVF_CNTRL_1_SEMI_PLANAR (1 << 6)
252 #define REG_RPT_CNTRL REG(0x00, 0xf0) /* write */
253 # define RPT_CNTRL_REPEAT(x) ((x) & 15)
254 #define REG_I2S_FORMAT REG(0x00, 0xfc) /* read/write */
255 # define I2S_FORMAT_PHILIPS (0 << 0)
256 # define I2S_FORMAT_LEFT_J (2 << 0)
257 # define I2S_FORMAT_RIGHT_J (3 << 0)
258 #define REG_AIP_CLKSEL REG(0x00, 0xfd) /* write */
259 # define AIP_CLKSEL_AIP_SPDIF (0 << 3)
260 # define AIP_CLKSEL_AIP_I2S (1 << 3)
261 # define AIP_CLKSEL_FS_ACLK (0 << 0)
262 # define AIP_CLKSEL_FS_MCLK (1 << 0)
263 # define AIP_CLKSEL_FS_FS64SPDIF (2 << 0)
264
265 /* Page 02h: PLL settings */
266 #define REG_PLL_SERIAL_1 REG(0x02, 0x00) /* read/write */
267 # define PLL_SERIAL_1_SRL_FDN (1 << 0)
268 # define PLL_SERIAL_1_SRL_IZ(x) (((x) & 3) << 1)
269 # define PLL_SERIAL_1_SRL_MAN_IZ (1 << 6)
270 #define REG_PLL_SERIAL_2 REG(0x02, 0x01) /* read/write */
271 # define PLL_SERIAL_2_SRL_NOSC(x) ((x) << 0)
272 # define PLL_SERIAL_2_SRL_PR(x) (((x) & 0xf) << 4)
273 #define REG_PLL_SERIAL_3 REG(0x02, 0x02) /* read/write */
274 # define PLL_SERIAL_3_SRL_CCIR (1 << 0)
275 # define PLL_SERIAL_3_SRL_DE (1 << 2)
276 # define PLL_SERIAL_3_SRL_PXIN_SEL (1 << 4)
277 #define REG_SERIALIZER REG(0x02, 0x03) /* read/write */
278 #define REG_BUFFER_OUT REG(0x02, 0x04) /* read/write */
279 #define REG_PLL_SCG1 REG(0x02, 0x05) /* read/write */
280 #define REG_PLL_SCG2 REG(0x02, 0x06) /* read/write */
281 #define REG_PLL_SCGN1 REG(0x02, 0x07) /* read/write */
282 #define REG_PLL_SCGN2 REG(0x02, 0x08) /* read/write */
283 #define REG_PLL_SCGR1 REG(0x02, 0x09) /* read/write */
284 #define REG_PLL_SCGR2 REG(0x02, 0x0a) /* read/write */
285 #define REG_AUDIO_DIV REG(0x02, 0x0e) /* read/write */
286 # define AUDIO_DIV_SERCLK_1 0
287 # define AUDIO_DIV_SERCLK_2 1
288 # define AUDIO_DIV_SERCLK_4 2
289 # define AUDIO_DIV_SERCLK_8 3
290 # define AUDIO_DIV_SERCLK_16 4
291 # define AUDIO_DIV_SERCLK_32 5
292 #define REG_SEL_CLK REG(0x02, 0x11) /* read/write */
293 # define SEL_CLK_SEL_CLK1 (1 << 0)
294 # define SEL_CLK_SEL_VRF_CLK(x) (((x) & 3) << 1)
295 # define SEL_CLK_ENA_SC_CLK (1 << 3)
296 #define REG_ANA_GENERAL REG(0x02, 0x12) /* read/write */
297
298
299 /* Page 09h: EDID Control */
300 #define REG_EDID_DATA_0 REG(0x09, 0x00) /* read */
301 /* next 127 successive registers are the EDID block */
302 #define REG_EDID_CTRL REG(0x09, 0xfa) /* read/write */
303 #define REG_DDC_ADDR REG(0x09, 0xfb) /* read/write */
304 #define REG_DDC_OFFS REG(0x09, 0xfc) /* read/write */
305 #define REG_DDC_SEGM_ADDR REG(0x09, 0xfd) /* read/write */
306 #define REG_DDC_SEGM REG(0x09, 0xfe) /* read/write */
307
308
309 /* Page 10h: information frames and packets */
310 #define REG_IF1_HB0 REG(0x10, 0x20) /* read/write */
311 #define REG_IF2_HB0 REG(0x10, 0x40) /* read/write */
312 #define REG_IF3_HB0 REG(0x10, 0x60) /* read/write */
313 #define REG_IF4_HB0 REG(0x10, 0x80) /* read/write */
314 #define REG_IF5_HB0 REG(0x10, 0xa0) /* read/write */
315
316
317 /* Page 11h: audio settings and content info packets */
318 #define REG_AIP_CNTRL_0 REG(0x11, 0x00) /* read/write */
319 # define AIP_CNTRL_0_RST_FIFO (1 << 0)
320 # define AIP_CNTRL_0_SWAP (1 << 1)
321 # define AIP_CNTRL_0_LAYOUT (1 << 2)
322 # define AIP_CNTRL_0_ACR_MAN (1 << 5)
323 # define AIP_CNTRL_0_RST_CTS (1 << 6)
324 #define REG_CA_I2S REG(0x11, 0x01) /* read/write */
325 # define CA_I2S_CA_I2S(x) (((x) & 31) << 0)
326 # define CA_I2S_HBR_CHSTAT (1 << 6)
327 #define REG_LATENCY_RD REG(0x11, 0x04) /* read/write */
328 #define REG_ACR_CTS_0 REG(0x11, 0x05) /* read/write */
329 #define REG_ACR_CTS_1 REG(0x11, 0x06) /* read/write */
330 #define REG_ACR_CTS_2 REG(0x11, 0x07) /* read/write */
331 #define REG_ACR_N_0 REG(0x11, 0x08) /* read/write */
332 #define REG_ACR_N_1 REG(0x11, 0x09) /* read/write */
333 #define REG_ACR_N_2 REG(0x11, 0x0a) /* read/write */
334 #define REG_CTS_N REG(0x11, 0x0c) /* read/write */
335 # define CTS_N_K(x) (((x) & 7) << 0)
336 # define CTS_N_M(x) (((x) & 3) << 4)
337 #define REG_ENC_CNTRL REG(0x11, 0x0d) /* read/write */
338 # define ENC_CNTRL_RST_ENC (1 << 0)
339 # define ENC_CNTRL_RST_SEL (1 << 1)
340 # define ENC_CNTRL_CTL_CODE(x) (((x) & 3) << 2)
341 #define REG_DIP_FLAGS REG(0x11, 0x0e) /* read/write */
342 # define DIP_FLAGS_ACR (1 << 0)
343 # define DIP_FLAGS_GC (1 << 1)
344 #define REG_DIP_IF_FLAGS REG(0x11, 0x0f) /* read/write */
345 # define DIP_IF_FLAGS_IF1 (1 << 1)
346 # define DIP_IF_FLAGS_IF2 (1 << 2)
347 # define DIP_IF_FLAGS_IF3 (1 << 3)
348 # define DIP_IF_FLAGS_IF4 (1 << 4)
349 # define DIP_IF_FLAGS_IF5 (1 << 5)
350 #define REG_CH_STAT_B(x) REG(0x11, 0x14 + (x)) /* read/write */
351
352
353 /* Page 12h: HDCP and OTP */
354 #define REG_TX3 REG(0x12, 0x9a) /* read/write */
355 #define REG_TX4 REG(0x12, 0x9b) /* read/write */
356 # define TX4_PD_RAM (1 << 1)
357 #define REG_TX33 REG(0x12, 0xb8) /* read/write */
358 # define TX33_HDMI (1 << 1)
359
360
361 /* Page 13h: Gamut related metadata packets */
362
363
364
365 /* CEC registers: (not paged)
366 */
367 #define REG_CEC_INTSTATUS 0xee /* read */
368 # define CEC_INTSTATUS_CEC (1 << 0)
369 # define CEC_INTSTATUS_HDMI (1 << 1)
370 #define REG_CEC_CAL_XOSC_CTRL1 0xf2
371 # define CEC_CAL_XOSC_CTRL1_ENA_CAL BIT(0)
372 #define REG_CEC_DES_FREQ2 0xf5
373 # define CEC_DES_FREQ2_DIS_AUTOCAL BIT(7)
374 #define REG_CEC_CLK 0xf6
375 # define CEC_CLK_FRO 0x11
376 #define REG_CEC_FRO_IM_CLK_CTRL 0xfb /* read/write */
377 # define CEC_FRO_IM_CLK_CTRL_GHOST_DIS (1 << 7)
378 # define CEC_FRO_IM_CLK_CTRL_ENA_OTP (1 << 6)
379 # define CEC_FRO_IM_CLK_CTRL_IMCLK_SEL (1 << 1)
380 # define CEC_FRO_IM_CLK_CTRL_FRO_DIV (1 << 0)
381 #define REG_CEC_RXSHPDINTENA 0xfc /* read/write */
382 #define REG_CEC_RXSHPDINT 0xfd /* read */
383 # define CEC_RXSHPDINT_RXSENS BIT(0)
384 # define CEC_RXSHPDINT_HPD BIT(1)
385 #define REG_CEC_RXSHPDLEV 0xfe /* read */
386 # define CEC_RXSHPDLEV_RXSENS (1 << 0)
387 # define CEC_RXSHPDLEV_HPD (1 << 1)
388
389 #define REG_CEC_ENAMODS 0xff /* read/write */
390 # define CEC_ENAMODS_EN_CEC_CLK (1 << 7)
391 # define CEC_ENAMODS_DIS_FRO (1 << 6)
392 # define CEC_ENAMODS_DIS_CCLK (1 << 5)
393 # define CEC_ENAMODS_EN_RXSENS (1 << 2)
394 # define CEC_ENAMODS_EN_HDMI (1 << 1)
395 # define CEC_ENAMODS_EN_CEC (1 << 0)
396
397
398 /* Device versions: */
399 #define TDA9989N2 0x0101
400 #define TDA19989 0x0201
401 #define TDA19989N2 0x0202
402 #define TDA19988 0x0301
403
404 static void
cec_write(struct tda998x_priv * priv,u16 addr,u8 val)405 cec_write(struct tda998x_priv *priv, u16 addr, u8 val)
406 {
407 u8 buf[] = {addr, val};
408 struct i2c_msg msg = {
409 .addr = priv->cec_addr,
410 .len = 2,
411 .buf = buf,
412 };
413 int ret;
414
415 ret = i2c_transfer(priv->hdmi->adapter, &msg, 1);
416 if (ret < 0)
417 dev_err(&priv->hdmi->dev, "Error %d writing to cec:0x%x\n",
418 ret, addr);
419 }
420
421 static u8
cec_read(struct tda998x_priv * priv,u8 addr)422 cec_read(struct tda998x_priv *priv, u8 addr)
423 {
424 u8 val;
425 struct i2c_msg msg[2] = {
426 {
427 .addr = priv->cec_addr,
428 .len = 1,
429 .buf = &addr,
430 }, {
431 .addr = priv->cec_addr,
432 .flags = I2C_M_RD,
433 .len = 1,
434 .buf = &val,
435 },
436 };
437 int ret;
438
439 ret = i2c_transfer(priv->hdmi->adapter, msg, ARRAY_SIZE(msg));
440 if (ret < 0) {
441 dev_err(&priv->hdmi->dev, "Error %d reading from cec:0x%x\n",
442 ret, addr);
443 val = 0;
444 }
445
446 return val;
447 }
448
cec_enamods(struct tda998x_priv * priv,u8 mods,bool enable)449 static void cec_enamods(struct tda998x_priv *priv, u8 mods, bool enable)
450 {
451 int val = cec_read(priv, REG_CEC_ENAMODS);
452
453 if (val < 0)
454 return;
455
456 if (enable)
457 val |= mods;
458 else
459 val &= ~mods;
460
461 cec_write(priv, REG_CEC_ENAMODS, val);
462 }
463
tda998x_cec_set_calibration(struct tda998x_priv * priv,bool enable)464 static void tda998x_cec_set_calibration(struct tda998x_priv *priv, bool enable)
465 {
466 if (enable) {
467 u8 val;
468
469 cec_write(priv, 0xf3, 0xc0);
470 cec_write(priv, 0xf4, 0xd4);
471
472 /* Enable automatic calibration mode */
473 val = cec_read(priv, REG_CEC_DES_FREQ2);
474 val &= ~CEC_DES_FREQ2_DIS_AUTOCAL;
475 cec_write(priv, REG_CEC_DES_FREQ2, val);
476
477 /* Enable free running oscillator */
478 cec_write(priv, REG_CEC_CLK, CEC_CLK_FRO);
479 cec_enamods(priv, CEC_ENAMODS_DIS_FRO, false);
480
481 cec_write(priv, REG_CEC_CAL_XOSC_CTRL1,
482 CEC_CAL_XOSC_CTRL1_ENA_CAL);
483 } else {
484 cec_write(priv, REG_CEC_CAL_XOSC_CTRL1, 0);
485 }
486 }
487
488 /*
489 * Calibration for the internal oscillator: we need to set calibration mode,
490 * and then pulse the IRQ line low for a 10ms ± 1% period.
491 */
tda998x_cec_calibration(struct tda998x_priv * priv)492 static void tda998x_cec_calibration(struct tda998x_priv *priv)
493 {
494 struct gpio_desc *calib = priv->calib;
495
496 mutex_lock(&priv->edid_mutex);
497 if (priv->hdmi->irq > 0)
498 disable_irq(priv->hdmi->irq);
499 gpiod_direction_output(calib, 1);
500 tda998x_cec_set_calibration(priv, true);
501
502 local_irq_disable();
503 gpiod_set_value(calib, 0);
504 mdelay(10);
505 gpiod_set_value(calib, 1);
506 local_irq_enable();
507
508 tda998x_cec_set_calibration(priv, false);
509 gpiod_direction_input(calib);
510 if (priv->hdmi->irq > 0)
511 enable_irq(priv->hdmi->irq);
512 mutex_unlock(&priv->edid_mutex);
513 }
514
tda998x_cec_hook_init(void * data)515 static int tda998x_cec_hook_init(void *data)
516 {
517 struct tda998x_priv *priv = data;
518 struct gpio_desc *calib;
519
520 calib = gpiod_get(&priv->hdmi->dev, "nxp,calib", GPIOD_ASIS);
521 if (IS_ERR(calib)) {
522 dev_warn(&priv->hdmi->dev, "failed to get calibration gpio: %ld\n",
523 PTR_ERR(calib));
524 return PTR_ERR(calib);
525 }
526
527 priv->calib = calib;
528
529 return 0;
530 }
531
tda998x_cec_hook_exit(void * data)532 static void tda998x_cec_hook_exit(void *data)
533 {
534 struct tda998x_priv *priv = data;
535
536 gpiod_put(priv->calib);
537 priv->calib = NULL;
538 }
539
tda998x_cec_hook_open(void * data)540 static int tda998x_cec_hook_open(void *data)
541 {
542 struct tda998x_priv *priv = data;
543
544 cec_enamods(priv, CEC_ENAMODS_EN_CEC_CLK | CEC_ENAMODS_EN_CEC, true);
545 tda998x_cec_calibration(priv);
546
547 return 0;
548 }
549
tda998x_cec_hook_release(void * data)550 static void tda998x_cec_hook_release(void *data)
551 {
552 struct tda998x_priv *priv = data;
553
554 cec_enamods(priv, CEC_ENAMODS_EN_CEC_CLK | CEC_ENAMODS_EN_CEC, false);
555 }
556
557 static int
set_page(struct tda998x_priv * priv,u16 reg)558 set_page(struct tda998x_priv *priv, u16 reg)
559 {
560 if (REG2PAGE(reg) != priv->current_page) {
561 struct i2c_client *client = priv->hdmi;
562 u8 buf[] = {
563 REG_CURPAGE, REG2PAGE(reg)
564 };
565 int ret = i2c_master_send(client, buf, sizeof(buf));
566 if (ret < 0) {
567 dev_err(&client->dev, "%s %04x err %d\n", __func__,
568 reg, ret);
569 return ret;
570 }
571
572 priv->current_page = REG2PAGE(reg);
573 }
574 return 0;
575 }
576
577 static int
reg_read_range(struct tda998x_priv * priv,u16 reg,char * buf,int cnt)578 reg_read_range(struct tda998x_priv *priv, u16 reg, char *buf, int cnt)
579 {
580 struct i2c_client *client = priv->hdmi;
581 u8 addr = REG2ADDR(reg);
582 int ret;
583
584 mutex_lock(&priv->mutex);
585 ret = set_page(priv, reg);
586 if (ret < 0)
587 goto out;
588
589 ret = i2c_master_send(client, &addr, sizeof(addr));
590 if (ret < 0)
591 goto fail;
592
593 ret = i2c_master_recv(client, buf, cnt);
594 if (ret < 0)
595 goto fail;
596
597 goto out;
598
599 fail:
600 dev_err(&client->dev, "Error %d reading from 0x%x\n", ret, reg);
601 out:
602 mutex_unlock(&priv->mutex);
603 return ret;
604 }
605
606 #define MAX_WRITE_RANGE_BUF 32
607
608 static void
reg_write_range(struct tda998x_priv * priv,u16 reg,u8 * p,int cnt)609 reg_write_range(struct tda998x_priv *priv, u16 reg, u8 *p, int cnt)
610 {
611 struct i2c_client *client = priv->hdmi;
612 /* This is the maximum size of the buffer passed in */
613 u8 buf[MAX_WRITE_RANGE_BUF + 1];
614 int ret;
615
616 if (cnt > MAX_WRITE_RANGE_BUF) {
617 dev_err(&client->dev, "Fixed write buffer too small (%d)\n",
618 MAX_WRITE_RANGE_BUF);
619 return;
620 }
621
622 buf[0] = REG2ADDR(reg);
623 memcpy(&buf[1], p, cnt);
624
625 mutex_lock(&priv->mutex);
626 ret = set_page(priv, reg);
627 if (ret < 0)
628 goto out;
629
630 ret = i2c_master_send(client, buf, cnt + 1);
631 if (ret < 0)
632 dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg);
633 out:
634 mutex_unlock(&priv->mutex);
635 }
636
637 static int
reg_read(struct tda998x_priv * priv,u16 reg)638 reg_read(struct tda998x_priv *priv, u16 reg)
639 {
640 u8 val = 0;
641 int ret;
642
643 ret = reg_read_range(priv, reg, &val, sizeof(val));
644 if (ret < 0)
645 return ret;
646 return val;
647 }
648
649 static void
reg_write(struct tda998x_priv * priv,u16 reg,u8 val)650 reg_write(struct tda998x_priv *priv, u16 reg, u8 val)
651 {
652 struct i2c_client *client = priv->hdmi;
653 u8 buf[] = {REG2ADDR(reg), val};
654 int ret;
655
656 mutex_lock(&priv->mutex);
657 ret = set_page(priv, reg);
658 if (ret < 0)
659 goto out;
660
661 ret = i2c_master_send(client, buf, sizeof(buf));
662 if (ret < 0)
663 dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg);
664 out:
665 mutex_unlock(&priv->mutex);
666 }
667
668 static void
reg_write16(struct tda998x_priv * priv,u16 reg,u16 val)669 reg_write16(struct tda998x_priv *priv, u16 reg, u16 val)
670 {
671 struct i2c_client *client = priv->hdmi;
672 u8 buf[] = {REG2ADDR(reg), val >> 8, val};
673 int ret;
674
675 mutex_lock(&priv->mutex);
676 ret = set_page(priv, reg);
677 if (ret < 0)
678 goto out;
679
680 ret = i2c_master_send(client, buf, sizeof(buf));
681 if (ret < 0)
682 dev_err(&client->dev, "Error %d writing to 0x%x\n", ret, reg);
683 out:
684 mutex_unlock(&priv->mutex);
685 }
686
687 static void
reg_set(struct tda998x_priv * priv,u16 reg,u8 val)688 reg_set(struct tda998x_priv *priv, u16 reg, u8 val)
689 {
690 int old_val;
691
692 old_val = reg_read(priv, reg);
693 if (old_val >= 0)
694 reg_write(priv, reg, old_val | val);
695 }
696
697 static void
reg_clear(struct tda998x_priv * priv,u16 reg,u8 val)698 reg_clear(struct tda998x_priv *priv, u16 reg, u8 val)
699 {
700 int old_val;
701
702 old_val = reg_read(priv, reg);
703 if (old_val >= 0)
704 reg_write(priv, reg, old_val & ~val);
705 }
706
707 static void
tda998x_reset(struct tda998x_priv * priv)708 tda998x_reset(struct tda998x_priv *priv)
709 {
710 /* reset audio and i2c master: */
711 reg_write(priv, REG_SOFTRESET, SOFTRESET_AUDIO | SOFTRESET_I2C_MASTER);
712 msleep(50);
713 reg_write(priv, REG_SOFTRESET, 0);
714 msleep(50);
715
716 /* reset transmitter: */
717 reg_set(priv, REG_MAIN_CNTRL0, MAIN_CNTRL0_SR);
718 reg_clear(priv, REG_MAIN_CNTRL0, MAIN_CNTRL0_SR);
719
720 /* PLL registers common configuration */
721 reg_write(priv, REG_PLL_SERIAL_1, 0x00);
722 reg_write(priv, REG_PLL_SERIAL_2, PLL_SERIAL_2_SRL_NOSC(1));
723 reg_write(priv, REG_PLL_SERIAL_3, 0x00);
724 reg_write(priv, REG_SERIALIZER, 0x00);
725 reg_write(priv, REG_BUFFER_OUT, 0x00);
726 reg_write(priv, REG_PLL_SCG1, 0x00);
727 reg_write(priv, REG_AUDIO_DIV, AUDIO_DIV_SERCLK_8);
728 reg_write(priv, REG_SEL_CLK, SEL_CLK_SEL_CLK1 | SEL_CLK_ENA_SC_CLK);
729 reg_write(priv, REG_PLL_SCGN1, 0xfa);
730 reg_write(priv, REG_PLL_SCGN2, 0x00);
731 reg_write(priv, REG_PLL_SCGR1, 0x5b);
732 reg_write(priv, REG_PLL_SCGR2, 0x00);
733 reg_write(priv, REG_PLL_SCG2, 0x10);
734
735 /* Write the default value MUX register */
736 reg_write(priv, REG_MUX_VP_VIP_OUT, 0x24);
737 }
738
739 /*
740 * The TDA998x has a problem when trying to read the EDID close to a
741 * HPD assertion: it needs a delay of 100ms to avoid timing out while
742 * trying to read EDID data.
743 *
744 * However, tda998x_connector_get_modes() may be called at any moment
745 * after tda998x_connector_detect() indicates that we are connected, so
746 * we need to delay probing modes in tda998x_connector_get_modes() after
747 * we have seen a HPD inactive->active transition. This code implements
748 * that delay.
749 */
tda998x_edid_delay_done(struct timer_list * t)750 static void tda998x_edid_delay_done(struct timer_list *t)
751 {
752 struct tda998x_priv *priv = from_timer(priv, t, edid_delay_timer);
753
754 priv->edid_delay_active = false;
755 wake_up(&priv->edid_delay_waitq);
756 schedule_work(&priv->detect_work);
757 }
758
tda998x_edid_delay_start(struct tda998x_priv * priv)759 static void tda998x_edid_delay_start(struct tda998x_priv *priv)
760 {
761 priv->edid_delay_active = true;
762 mod_timer(&priv->edid_delay_timer, jiffies + HZ/10);
763 }
764
tda998x_edid_delay_wait(struct tda998x_priv * priv)765 static int tda998x_edid_delay_wait(struct tda998x_priv *priv)
766 {
767 return wait_event_killable(priv->edid_delay_waitq, !priv->edid_delay_active);
768 }
769
770 /*
771 * We need to run the KMS hotplug event helper outside of our threaded
772 * interrupt routine as this can call back into our get_modes method,
773 * which will want to make use of interrupts.
774 */
tda998x_detect_work(struct work_struct * work)775 static void tda998x_detect_work(struct work_struct *work)
776 {
777 struct tda998x_priv *priv =
778 container_of(work, struct tda998x_priv, detect_work);
779 struct drm_device *dev = priv->connector.dev;
780
781 if (dev)
782 drm_kms_helper_hotplug_event(dev);
783 }
784
785 /*
786 * only 2 interrupts may occur: screen plug/unplug and EDID read
787 */
tda998x_irq_thread(int irq,void * data)788 static irqreturn_t tda998x_irq_thread(int irq, void *data)
789 {
790 struct tda998x_priv *priv = data;
791 u8 sta, cec, lvl, flag0, flag1, flag2;
792 bool handled = false;
793
794 sta = cec_read(priv, REG_CEC_INTSTATUS);
795 if (sta & CEC_INTSTATUS_HDMI) {
796 cec = cec_read(priv, REG_CEC_RXSHPDINT);
797 lvl = cec_read(priv, REG_CEC_RXSHPDLEV);
798 flag0 = reg_read(priv, REG_INT_FLAGS_0);
799 flag1 = reg_read(priv, REG_INT_FLAGS_1);
800 flag2 = reg_read(priv, REG_INT_FLAGS_2);
801 DRM_DEBUG_DRIVER(
802 "tda irq sta %02x cec %02x lvl %02x f0 %02x f1 %02x f2 %02x\n",
803 sta, cec, lvl, flag0, flag1, flag2);
804
805 if (cec & CEC_RXSHPDINT_HPD) {
806 if (lvl & CEC_RXSHPDLEV_HPD) {
807 tda998x_edid_delay_start(priv);
808 } else {
809 schedule_work(&priv->detect_work);
810 cec_notifier_phys_addr_invalidate(
811 priv->cec_notify);
812 }
813
814 handled = true;
815 }
816
817 if ((flag2 & INT_FLAGS_2_EDID_BLK_RD) && priv->wq_edid_wait) {
818 priv->wq_edid_wait = 0;
819 wake_up(&priv->wq_edid);
820 handled = true;
821 }
822 }
823
824 return IRQ_RETVAL(handled);
825 }
826
827 static void
tda998x_write_if(struct tda998x_priv * priv,u8 bit,u16 addr,union hdmi_infoframe * frame)828 tda998x_write_if(struct tda998x_priv *priv, u8 bit, u16 addr,
829 union hdmi_infoframe *frame)
830 {
831 u8 buf[MAX_WRITE_RANGE_BUF];
832 ssize_t len;
833
834 len = hdmi_infoframe_pack(frame, buf, sizeof(buf));
835 if (len < 0) {
836 dev_err(&priv->hdmi->dev,
837 "hdmi_infoframe_pack() type=0x%02x failed: %zd\n",
838 frame->any.type, len);
839 return;
840 }
841
842 reg_clear(priv, REG_DIP_IF_FLAGS, bit);
843 reg_write_range(priv, addr, buf, len);
844 reg_set(priv, REG_DIP_IF_FLAGS, bit);
845 }
846
tda998x_write_aif(struct tda998x_priv * priv,const struct hdmi_audio_infoframe * cea)847 static void tda998x_write_aif(struct tda998x_priv *priv,
848 const struct hdmi_audio_infoframe *cea)
849 {
850 union hdmi_infoframe frame;
851
852 frame.audio = *cea;
853
854 tda998x_write_if(priv, DIP_IF_FLAGS_IF4, REG_IF4_HB0, &frame);
855 }
856
857 static void
tda998x_write_avi(struct tda998x_priv * priv,const struct drm_display_mode * mode)858 tda998x_write_avi(struct tda998x_priv *priv, const struct drm_display_mode *mode)
859 {
860 union hdmi_infoframe frame;
861
862 drm_hdmi_avi_infoframe_from_display_mode(&frame.avi,
863 &priv->connector, mode);
864 frame.avi.quantization_range = HDMI_QUANTIZATION_RANGE_FULL;
865 drm_hdmi_avi_infoframe_quant_range(&frame.avi, &priv->connector, mode,
866 priv->rgb_quant_range);
867
868 tda998x_write_if(priv, DIP_IF_FLAGS_IF2, REG_IF2_HB0, &frame);
869 }
870
tda998x_write_vsi(struct tda998x_priv * priv,const struct drm_display_mode * mode)871 static void tda998x_write_vsi(struct tda998x_priv *priv,
872 const struct drm_display_mode *mode)
873 {
874 union hdmi_infoframe frame;
875
876 if (drm_hdmi_vendor_infoframe_from_display_mode(&frame.vendor.hdmi,
877 &priv->connector,
878 mode))
879 reg_clear(priv, REG_DIP_IF_FLAGS, DIP_IF_FLAGS_IF1);
880 else
881 tda998x_write_if(priv, DIP_IF_FLAGS_IF1, REG_IF1_HB0, &frame);
882 }
883
884 /* Audio support */
885
886 static const struct tda998x_audio_route tda998x_audio_route[AUDIO_ROUTE_NUM] = {
887 [AUDIO_ROUTE_I2S] = {
888 .ena_aclk = 1,
889 .mux_ap = MUX_AP_SELECT_I2S,
890 .aip_clksel = AIP_CLKSEL_AIP_I2S | AIP_CLKSEL_FS_ACLK,
891 },
892 [AUDIO_ROUTE_SPDIF] = {
893 .ena_aclk = 0,
894 .mux_ap = MUX_AP_SELECT_SPDIF,
895 .aip_clksel = AIP_CLKSEL_AIP_SPDIF | AIP_CLKSEL_FS_FS64SPDIF,
896 },
897 };
898
899 /* Configure the TDA998x audio data and clock routing. */
tda998x_derive_routing(struct tda998x_priv * priv,struct tda998x_audio_settings * s,unsigned int route)900 static int tda998x_derive_routing(struct tda998x_priv *priv,
901 struct tda998x_audio_settings *s,
902 unsigned int route)
903 {
904 s->route = &tda998x_audio_route[route];
905 s->ena_ap = priv->audio_port_enable[route];
906 if (s->ena_ap == 0) {
907 dev_err(&priv->hdmi->dev, "no audio configuration found\n");
908 return -EINVAL;
909 }
910
911 return 0;
912 }
913
914 /*
915 * The audio clock divisor register controls a divider producing Audio_Clk_Out
916 * from SERclk by dividing it by 2^n where 0 <= n <= 5. We don't know what
917 * Audio_Clk_Out or SERclk are. We guess SERclk is the same as TMDS clock.
918 *
919 * It seems that Audio_Clk_Out must be the smallest value that is greater
920 * than 128*fs, otherwise audio does not function. There is some suggestion
921 * that 126*fs is a better value.
922 */
tda998x_get_adiv(struct tda998x_priv * priv,unsigned int fs)923 static u8 tda998x_get_adiv(struct tda998x_priv *priv, unsigned int fs)
924 {
925 unsigned long min_audio_clk = fs * 128;
926 unsigned long ser_clk = priv->tmds_clock * 1000;
927 u8 adiv;
928
929 for (adiv = AUDIO_DIV_SERCLK_32; adiv != AUDIO_DIV_SERCLK_1; adiv--)
930 if (ser_clk > min_audio_clk << adiv)
931 break;
932
933 dev_dbg(&priv->hdmi->dev,
934 "ser_clk=%luHz fs=%uHz min_aclk=%luHz adiv=%d\n",
935 ser_clk, fs, min_audio_clk, adiv);
936
937 return adiv;
938 }
939
940 /*
941 * In auto-CTS mode, the TDA998x uses a "measured time stamp" counter to
942 * generate the CTS value. It appears that the "measured time stamp" is
943 * the number of TDMS clock cycles within a number of audio input clock
944 * cycles defined by the k and N parameters defined below, in a similar
945 * way to that which is set out in the CTS generation in the HDMI spec.
946 *
947 * tmdsclk ----> mts -> /m ---> CTS
948 * ^
949 * sclk -> /k -> /N
950 *
951 * CTS = mts / m, where m is 2^M.
952 * /k is a divider based on the K value below, K+1 for K < 4, or 8 for K >= 4
953 * /N is a divider based on the HDMI specified N value.
954 *
955 * This produces the following equation:
956 * CTS = tmds_clock * k * N / (sclk * m)
957 *
958 * When combined with the sink-side equation, and realising that sclk is
959 * bclk_ratio * fs, we end up with:
960 * k = m * bclk_ratio / 128.
961 *
962 * Note: S/PDIF always uses a bclk_ratio of 64.
963 */
tda998x_derive_cts_n(struct tda998x_priv * priv,struct tda998x_audio_settings * settings,unsigned int ratio)964 static int tda998x_derive_cts_n(struct tda998x_priv *priv,
965 struct tda998x_audio_settings *settings,
966 unsigned int ratio)
967 {
968 switch (ratio) {
969 case 16:
970 settings->cts_n = CTS_N_M(3) | CTS_N_K(0);
971 break;
972 case 32:
973 settings->cts_n = CTS_N_M(3) | CTS_N_K(1);
974 break;
975 case 48:
976 settings->cts_n = CTS_N_M(3) | CTS_N_K(2);
977 break;
978 case 64:
979 settings->cts_n = CTS_N_M(3) | CTS_N_K(3);
980 break;
981 case 128:
982 settings->cts_n = CTS_N_M(0) | CTS_N_K(0);
983 break;
984 default:
985 dev_err(&priv->hdmi->dev, "unsupported bclk ratio %ufs\n",
986 ratio);
987 return -EINVAL;
988 }
989 return 0;
990 }
991
tda998x_audio_mute(struct tda998x_priv * priv,bool on)992 static void tda998x_audio_mute(struct tda998x_priv *priv, bool on)
993 {
994 if (on) {
995 reg_set(priv, REG_SOFTRESET, SOFTRESET_AUDIO);
996 reg_clear(priv, REG_SOFTRESET, SOFTRESET_AUDIO);
997 reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO);
998 } else {
999 reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO);
1000 }
1001 }
1002
tda998x_configure_audio(struct tda998x_priv * priv)1003 static void tda998x_configure_audio(struct tda998x_priv *priv)
1004 {
1005 const struct tda998x_audio_settings *settings = &priv->audio;
1006 u8 buf[6], adiv;
1007 u32 n;
1008
1009 /* If audio is not configured, there is nothing to do. */
1010 if (settings->ena_ap == 0)
1011 return;
1012
1013 adiv = tda998x_get_adiv(priv, settings->sample_rate);
1014
1015 /* Enable audio ports */
1016 reg_write(priv, REG_ENA_AP, settings->ena_ap);
1017 reg_write(priv, REG_ENA_ACLK, settings->route->ena_aclk);
1018 reg_write(priv, REG_MUX_AP, settings->route->mux_ap);
1019 reg_write(priv, REG_I2S_FORMAT, settings->i2s_format);
1020 reg_write(priv, REG_AIP_CLKSEL, settings->route->aip_clksel);
1021 reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_LAYOUT |
1022 AIP_CNTRL_0_ACR_MAN); /* auto CTS */
1023 reg_write(priv, REG_CTS_N, settings->cts_n);
1024 reg_write(priv, REG_AUDIO_DIV, adiv);
1025
1026 /*
1027 * This is the approximate value of N, which happens to be
1028 * the recommended values for non-coherent clocks.
1029 */
1030 n = 128 * settings->sample_rate / 1000;
1031
1032 /* Write the CTS and N values */
1033 buf[0] = 0x44;
1034 buf[1] = 0x42;
1035 buf[2] = 0x01;
1036 buf[3] = n;
1037 buf[4] = n >> 8;
1038 buf[5] = n >> 16;
1039 reg_write_range(priv, REG_ACR_CTS_0, buf, 6);
1040
1041 /* Reset CTS generator */
1042 reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_CTS);
1043 reg_clear(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_CTS);
1044
1045 /* Write the channel status
1046 * The REG_CH_STAT_B-registers skip IEC958 AES2 byte, because
1047 * there is a separate register for each I2S wire.
1048 */
1049 buf[0] = settings->status[0];
1050 buf[1] = settings->status[1];
1051 buf[2] = settings->status[3];
1052 buf[3] = settings->status[4];
1053 reg_write_range(priv, REG_CH_STAT_B(0), buf, 4);
1054
1055 tda998x_audio_mute(priv, true);
1056 msleep(20);
1057 tda998x_audio_mute(priv, false);
1058
1059 tda998x_write_aif(priv, &settings->cea);
1060 }
1061
tda998x_audio_hw_params(struct device * dev,void * data,struct hdmi_codec_daifmt * daifmt,struct hdmi_codec_params * params)1062 static int tda998x_audio_hw_params(struct device *dev, void *data,
1063 struct hdmi_codec_daifmt *daifmt,
1064 struct hdmi_codec_params *params)
1065 {
1066 struct tda998x_priv *priv = dev_get_drvdata(dev);
1067 unsigned int bclk_ratio;
1068 bool spdif = daifmt->fmt == HDMI_SPDIF;
1069 int ret;
1070 struct tda998x_audio_settings audio = {
1071 .sample_rate = params->sample_rate,
1072 .cea = params->cea,
1073 };
1074
1075 memcpy(audio.status, params->iec.status,
1076 min(sizeof(audio.status), sizeof(params->iec.status)));
1077
1078 switch (daifmt->fmt) {
1079 case HDMI_I2S:
1080 audio.i2s_format = I2S_FORMAT_PHILIPS;
1081 break;
1082 case HDMI_LEFT_J:
1083 audio.i2s_format = I2S_FORMAT_LEFT_J;
1084 break;
1085 case HDMI_RIGHT_J:
1086 audio.i2s_format = I2S_FORMAT_RIGHT_J;
1087 break;
1088 case HDMI_SPDIF:
1089 audio.i2s_format = 0;
1090 break;
1091 default:
1092 dev_err(dev, "%s: Invalid format %d\n", __func__, daifmt->fmt);
1093 return -EINVAL;
1094 }
1095
1096 if (!spdif &&
1097 (daifmt->bit_clk_inv || daifmt->frame_clk_inv ||
1098 daifmt->bit_clk_master || daifmt->frame_clk_master)) {
1099 dev_err(dev, "%s: Bad flags %d %d %d %d\n", __func__,
1100 daifmt->bit_clk_inv, daifmt->frame_clk_inv,
1101 daifmt->bit_clk_master,
1102 daifmt->frame_clk_master);
1103 return -EINVAL;
1104 }
1105
1106 ret = tda998x_derive_routing(priv, &audio, AUDIO_ROUTE_I2S + spdif);
1107 if (ret < 0)
1108 return ret;
1109
1110 bclk_ratio = spdif ? 64 : params->sample_width * 2;
1111 ret = tda998x_derive_cts_n(priv, &audio, bclk_ratio);
1112 if (ret < 0)
1113 return ret;
1114
1115 mutex_lock(&priv->audio_mutex);
1116 priv->audio = audio;
1117 if (priv->supports_infoframes && priv->sink_has_audio)
1118 tda998x_configure_audio(priv);
1119 mutex_unlock(&priv->audio_mutex);
1120
1121 return 0;
1122 }
1123
tda998x_audio_shutdown(struct device * dev,void * data)1124 static void tda998x_audio_shutdown(struct device *dev, void *data)
1125 {
1126 struct tda998x_priv *priv = dev_get_drvdata(dev);
1127
1128 mutex_lock(&priv->audio_mutex);
1129
1130 reg_write(priv, REG_ENA_AP, 0);
1131 priv->audio.ena_ap = 0;
1132
1133 mutex_unlock(&priv->audio_mutex);
1134 }
1135
tda998x_audio_mute_stream(struct device * dev,void * data,bool enable,int direction)1136 static int tda998x_audio_mute_stream(struct device *dev, void *data,
1137 bool enable, int direction)
1138 {
1139 struct tda998x_priv *priv = dev_get_drvdata(dev);
1140
1141 mutex_lock(&priv->audio_mutex);
1142
1143 tda998x_audio_mute(priv, enable);
1144
1145 mutex_unlock(&priv->audio_mutex);
1146 return 0;
1147 }
1148
tda998x_audio_get_eld(struct device * dev,void * data,uint8_t * buf,size_t len)1149 static int tda998x_audio_get_eld(struct device *dev, void *data,
1150 uint8_t *buf, size_t len)
1151 {
1152 struct tda998x_priv *priv = dev_get_drvdata(dev);
1153
1154 mutex_lock(&priv->audio_mutex);
1155 memcpy(buf, priv->connector.eld,
1156 min(sizeof(priv->connector.eld), len));
1157 mutex_unlock(&priv->audio_mutex);
1158
1159 return 0;
1160 }
1161
1162 static const struct hdmi_codec_ops audio_codec_ops = {
1163 .hw_params = tda998x_audio_hw_params,
1164 .audio_shutdown = tda998x_audio_shutdown,
1165 .mute_stream = tda998x_audio_mute_stream,
1166 .get_eld = tda998x_audio_get_eld,
1167 .no_capture_mute = 1,
1168 };
1169
tda998x_audio_codec_init(struct tda998x_priv * priv,struct device * dev)1170 static int tda998x_audio_codec_init(struct tda998x_priv *priv,
1171 struct device *dev)
1172 {
1173 struct hdmi_codec_pdata codec_data = {
1174 .ops = &audio_codec_ops,
1175 .max_i2s_channels = 2,
1176 };
1177
1178 if (priv->audio_port_enable[AUDIO_ROUTE_I2S])
1179 codec_data.i2s = 1;
1180 if (priv->audio_port_enable[AUDIO_ROUTE_SPDIF])
1181 codec_data.spdif = 1;
1182
1183 priv->audio_pdev = platform_device_register_data(
1184 dev, HDMI_CODEC_DRV_NAME, PLATFORM_DEVID_AUTO,
1185 &codec_data, sizeof(codec_data));
1186
1187 return PTR_ERR_OR_ZERO(priv->audio_pdev);
1188 }
1189
1190 /* DRM connector functions */
1191
1192 static enum drm_connector_status
tda998x_connector_detect(struct drm_connector * connector,bool force)1193 tda998x_connector_detect(struct drm_connector *connector, bool force)
1194 {
1195 struct tda998x_priv *priv = conn_to_tda998x_priv(connector);
1196 u8 val = cec_read(priv, REG_CEC_RXSHPDLEV);
1197
1198 return (val & CEC_RXSHPDLEV_HPD) ? connector_status_connected :
1199 connector_status_disconnected;
1200 }
1201
tda998x_connector_destroy(struct drm_connector * connector)1202 static void tda998x_connector_destroy(struct drm_connector *connector)
1203 {
1204 drm_connector_cleanup(connector);
1205 }
1206
1207 static const struct drm_connector_funcs tda998x_connector_funcs = {
1208 .reset = drm_atomic_helper_connector_reset,
1209 .fill_modes = drm_helper_probe_single_connector_modes,
1210 .detect = tda998x_connector_detect,
1211 .destroy = tda998x_connector_destroy,
1212 .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
1213 .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
1214 };
1215
read_edid_block(void * data,u8 * buf,unsigned int blk,size_t length)1216 static int read_edid_block(void *data, u8 *buf, unsigned int blk, size_t length)
1217 {
1218 struct tda998x_priv *priv = data;
1219 u8 offset, segptr;
1220 int ret, i;
1221
1222 offset = (blk & 1) ? 128 : 0;
1223 segptr = blk / 2;
1224
1225 mutex_lock(&priv->edid_mutex);
1226
1227 reg_write(priv, REG_DDC_ADDR, 0xa0);
1228 reg_write(priv, REG_DDC_OFFS, offset);
1229 reg_write(priv, REG_DDC_SEGM_ADDR, 0x60);
1230 reg_write(priv, REG_DDC_SEGM, segptr);
1231
1232 /* enable reading EDID: */
1233 priv->wq_edid_wait = 1;
1234 reg_write(priv, REG_EDID_CTRL, 0x1);
1235
1236 /* flag must be cleared by sw: */
1237 reg_write(priv, REG_EDID_CTRL, 0x0);
1238
1239 /* wait for block read to complete: */
1240 if (priv->hdmi->irq) {
1241 i = wait_event_timeout(priv->wq_edid,
1242 !priv->wq_edid_wait,
1243 msecs_to_jiffies(100));
1244 if (i < 0) {
1245 dev_err(&priv->hdmi->dev, "read edid wait err %d\n", i);
1246 ret = i;
1247 goto failed;
1248 }
1249 } else {
1250 for (i = 100; i > 0; i--) {
1251 msleep(1);
1252 ret = reg_read(priv, REG_INT_FLAGS_2);
1253 if (ret < 0)
1254 goto failed;
1255 if (ret & INT_FLAGS_2_EDID_BLK_RD)
1256 break;
1257 }
1258 }
1259
1260 if (i == 0) {
1261 dev_err(&priv->hdmi->dev, "read edid timeout\n");
1262 ret = -ETIMEDOUT;
1263 goto failed;
1264 }
1265
1266 ret = reg_read_range(priv, REG_EDID_DATA_0, buf, length);
1267 if (ret != length) {
1268 dev_err(&priv->hdmi->dev, "failed to read edid block %d: %d\n",
1269 blk, ret);
1270 goto failed;
1271 }
1272
1273 ret = 0;
1274
1275 failed:
1276 mutex_unlock(&priv->edid_mutex);
1277 return ret;
1278 }
1279
tda998x_connector_get_modes(struct drm_connector * connector)1280 static int tda998x_connector_get_modes(struct drm_connector *connector)
1281 {
1282 struct tda998x_priv *priv = conn_to_tda998x_priv(connector);
1283 struct edid *edid;
1284 int n;
1285
1286 /*
1287 * If we get killed while waiting for the HPD timeout, return
1288 * no modes found: we are not in a restartable path, so we
1289 * can't handle signals gracefully.
1290 */
1291 if (tda998x_edid_delay_wait(priv))
1292 return 0;
1293
1294 if (priv->rev == TDA19988)
1295 reg_clear(priv, REG_TX4, TX4_PD_RAM);
1296
1297 edid = drm_do_get_edid(connector, read_edid_block, priv);
1298
1299 if (priv->rev == TDA19988)
1300 reg_set(priv, REG_TX4, TX4_PD_RAM);
1301
1302 if (!edid) {
1303 dev_warn(&priv->hdmi->dev, "failed to read EDID\n");
1304 return 0;
1305 }
1306
1307 drm_connector_update_edid_property(connector, edid);
1308 cec_notifier_set_phys_addr_from_edid(priv->cec_notify, edid);
1309
1310 mutex_lock(&priv->audio_mutex);
1311 n = drm_add_edid_modes(connector, edid);
1312 priv->sink_has_audio = drm_detect_monitor_audio(edid);
1313 mutex_unlock(&priv->audio_mutex);
1314
1315 kfree(edid);
1316
1317 return n;
1318 }
1319
1320 static struct drm_encoder *
tda998x_connector_best_encoder(struct drm_connector * connector)1321 tda998x_connector_best_encoder(struct drm_connector *connector)
1322 {
1323 struct tda998x_priv *priv = conn_to_tda998x_priv(connector);
1324
1325 return priv->bridge.encoder;
1326 }
1327
1328 static
1329 const struct drm_connector_helper_funcs tda998x_connector_helper_funcs = {
1330 .get_modes = tda998x_connector_get_modes,
1331 .best_encoder = tda998x_connector_best_encoder,
1332 };
1333
tda998x_connector_init(struct tda998x_priv * priv,struct drm_device * drm)1334 static int tda998x_connector_init(struct tda998x_priv *priv,
1335 struct drm_device *drm)
1336 {
1337 struct drm_connector *connector = &priv->connector;
1338 int ret;
1339
1340 connector->interlace_allowed = 1;
1341
1342 if (priv->hdmi->irq)
1343 connector->polled = DRM_CONNECTOR_POLL_HPD;
1344 else
1345 connector->polled = DRM_CONNECTOR_POLL_CONNECT |
1346 DRM_CONNECTOR_POLL_DISCONNECT;
1347
1348 drm_connector_helper_add(connector, &tda998x_connector_helper_funcs);
1349 ret = drm_connector_init(drm, connector, &tda998x_connector_funcs,
1350 DRM_MODE_CONNECTOR_HDMIA);
1351 if (ret)
1352 return ret;
1353
1354 drm_connector_attach_encoder(&priv->connector,
1355 priv->bridge.encoder);
1356
1357 return 0;
1358 }
1359
1360 /* DRM bridge functions */
1361
tda998x_bridge_attach(struct drm_bridge * bridge,enum drm_bridge_attach_flags flags)1362 static int tda998x_bridge_attach(struct drm_bridge *bridge,
1363 enum drm_bridge_attach_flags flags)
1364 {
1365 struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge);
1366
1367 if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
1368 DRM_ERROR("Fix bridge driver to make connector optional!");
1369 return -EINVAL;
1370 }
1371
1372 return tda998x_connector_init(priv, bridge->dev);
1373 }
1374
tda998x_bridge_detach(struct drm_bridge * bridge)1375 static void tda998x_bridge_detach(struct drm_bridge *bridge)
1376 {
1377 struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge);
1378
1379 drm_connector_cleanup(&priv->connector);
1380 }
1381
tda998x_bridge_mode_valid(struct drm_bridge * bridge,const struct drm_display_info * info,const struct drm_display_mode * mode)1382 static enum drm_mode_status tda998x_bridge_mode_valid(struct drm_bridge *bridge,
1383 const struct drm_display_info *info,
1384 const struct drm_display_mode *mode)
1385 {
1386 /* TDA19988 dotclock can go up to 165MHz */
1387 struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge);
1388
1389 if (mode->clock > ((priv->rev == TDA19988) ? 165000 : 150000))
1390 return MODE_CLOCK_HIGH;
1391 if (mode->htotal >= BIT(13))
1392 return MODE_BAD_HVALUE;
1393 if (mode->vtotal >= BIT(11))
1394 return MODE_BAD_VVALUE;
1395 return MODE_OK;
1396 }
1397
tda998x_bridge_enable(struct drm_bridge * bridge)1398 static void tda998x_bridge_enable(struct drm_bridge *bridge)
1399 {
1400 struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge);
1401
1402 if (!priv->is_on) {
1403 /* enable video ports, audio will be enabled later */
1404 reg_write(priv, REG_ENA_VP_0, 0xff);
1405 reg_write(priv, REG_ENA_VP_1, 0xff);
1406 reg_write(priv, REG_ENA_VP_2, 0xff);
1407 /* set muxing after enabling ports: */
1408 reg_write(priv, REG_VIP_CNTRL_0, priv->vip_cntrl_0);
1409 reg_write(priv, REG_VIP_CNTRL_1, priv->vip_cntrl_1);
1410 reg_write(priv, REG_VIP_CNTRL_2, priv->vip_cntrl_2);
1411
1412 priv->is_on = true;
1413 }
1414 }
1415
tda998x_bridge_disable(struct drm_bridge * bridge)1416 static void tda998x_bridge_disable(struct drm_bridge *bridge)
1417 {
1418 struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge);
1419
1420 if (priv->is_on) {
1421 /* disable video ports */
1422 reg_write(priv, REG_ENA_VP_0, 0x00);
1423 reg_write(priv, REG_ENA_VP_1, 0x00);
1424 reg_write(priv, REG_ENA_VP_2, 0x00);
1425
1426 priv->is_on = false;
1427 }
1428 }
1429
tda998x_bridge_mode_set(struct drm_bridge * bridge,const struct drm_display_mode * mode,const struct drm_display_mode * adjusted_mode)1430 static void tda998x_bridge_mode_set(struct drm_bridge *bridge,
1431 const struct drm_display_mode *mode,
1432 const struct drm_display_mode *adjusted_mode)
1433 {
1434 struct tda998x_priv *priv = bridge_to_tda998x_priv(bridge);
1435 unsigned long tmds_clock;
1436 u16 ref_pix, ref_line, n_pix, n_line;
1437 u16 hs_pix_s, hs_pix_e;
1438 u16 vs1_pix_s, vs1_pix_e, vs1_line_s, vs1_line_e;
1439 u16 vs2_pix_s, vs2_pix_e, vs2_line_s, vs2_line_e;
1440 u16 vwin1_line_s, vwin1_line_e;
1441 u16 vwin2_line_s, vwin2_line_e;
1442 u16 de_pix_s, de_pix_e;
1443 u8 reg, div, rep, sel_clk;
1444
1445 /*
1446 * Since we are "computer" like, our source invariably produces
1447 * full-range RGB. If the monitor supports full-range, then use
1448 * it, otherwise reduce to limited-range.
1449 */
1450 priv->rgb_quant_range =
1451 priv->connector.display_info.rgb_quant_range_selectable ?
1452 HDMI_QUANTIZATION_RANGE_FULL :
1453 drm_default_rgb_quant_range(adjusted_mode);
1454
1455 /*
1456 * Internally TDA998x is using ITU-R BT.656 style sync but
1457 * we get VESA style sync. TDA998x is using a reference pixel
1458 * relative to ITU to sync to the input frame and for output
1459 * sync generation. Currently, we are using reference detection
1460 * from HS/VS, i.e. REFPIX/REFLINE denote frame start sync point
1461 * which is position of rising VS with coincident rising HS.
1462 *
1463 * Now there is some issues to take care of:
1464 * - HDMI data islands require sync-before-active
1465 * - TDA998x register values must be > 0 to be enabled
1466 * - REFLINE needs an additional offset of +1
1467 * - REFPIX needs an addtional offset of +1 for UYUV and +3 for RGB
1468 *
1469 * So we add +1 to all horizontal and vertical register values,
1470 * plus an additional +3 for REFPIX as we are using RGB input only.
1471 */
1472 n_pix = mode->htotal;
1473 n_line = mode->vtotal;
1474
1475 hs_pix_e = mode->hsync_end - mode->hdisplay;
1476 hs_pix_s = mode->hsync_start - mode->hdisplay;
1477 de_pix_e = mode->htotal;
1478 de_pix_s = mode->htotal - mode->hdisplay;
1479 ref_pix = 3 + hs_pix_s;
1480
1481 /*
1482 * Attached LCD controllers may generate broken sync. Allow
1483 * those to adjust the position of the rising VS edge by adding
1484 * HSKEW to ref_pix.
1485 */
1486 if (adjusted_mode->flags & DRM_MODE_FLAG_HSKEW)
1487 ref_pix += adjusted_mode->hskew;
1488
1489 if ((mode->flags & DRM_MODE_FLAG_INTERLACE) == 0) {
1490 ref_line = 1 + mode->vsync_start - mode->vdisplay;
1491 vwin1_line_s = mode->vtotal - mode->vdisplay - 1;
1492 vwin1_line_e = vwin1_line_s + mode->vdisplay;
1493 vs1_pix_s = vs1_pix_e = hs_pix_s;
1494 vs1_line_s = mode->vsync_start - mode->vdisplay;
1495 vs1_line_e = vs1_line_s +
1496 mode->vsync_end - mode->vsync_start;
1497 vwin2_line_s = vwin2_line_e = 0;
1498 vs2_pix_s = vs2_pix_e = 0;
1499 vs2_line_s = vs2_line_e = 0;
1500 } else {
1501 ref_line = 1 + (mode->vsync_start - mode->vdisplay)/2;
1502 vwin1_line_s = (mode->vtotal - mode->vdisplay)/2;
1503 vwin1_line_e = vwin1_line_s + mode->vdisplay/2;
1504 vs1_pix_s = vs1_pix_e = hs_pix_s;
1505 vs1_line_s = (mode->vsync_start - mode->vdisplay)/2;
1506 vs1_line_e = vs1_line_s +
1507 (mode->vsync_end - mode->vsync_start)/2;
1508 vwin2_line_s = vwin1_line_s + mode->vtotal/2;
1509 vwin2_line_e = vwin2_line_s + mode->vdisplay/2;
1510 vs2_pix_s = vs2_pix_e = hs_pix_s + mode->htotal/2;
1511 vs2_line_s = vs1_line_s + mode->vtotal/2 ;
1512 vs2_line_e = vs2_line_s +
1513 (mode->vsync_end - mode->vsync_start)/2;
1514 }
1515
1516 /*
1517 * Select pixel repeat depending on the double-clock flag
1518 * (which means we have to repeat each pixel once.)
1519 */
1520 rep = mode->flags & DRM_MODE_FLAG_DBLCLK ? 1 : 0;
1521 sel_clk = SEL_CLK_ENA_SC_CLK | SEL_CLK_SEL_CLK1 |
1522 SEL_CLK_SEL_VRF_CLK(rep ? 2 : 0);
1523
1524 /* the TMDS clock is scaled up by the pixel repeat */
1525 tmds_clock = mode->clock * (1 + rep);
1526
1527 /*
1528 * The divisor is power-of-2. The TDA9983B datasheet gives
1529 * this as ranges of Msample/s, which is 10x the TMDS clock:
1530 * 0 - 800 to 1500 Msample/s
1531 * 1 - 400 to 800 Msample/s
1532 * 2 - 200 to 400 Msample/s
1533 * 3 - as 2 above
1534 */
1535 for (div = 0; div < 3; div++)
1536 if (80000 >> div <= tmds_clock)
1537 break;
1538
1539 mutex_lock(&priv->audio_mutex);
1540
1541 priv->tmds_clock = tmds_clock;
1542
1543 /* mute the audio FIFO: */
1544 reg_set(priv, REG_AIP_CNTRL_0, AIP_CNTRL_0_RST_FIFO);
1545
1546 /* set HDMI HDCP mode off: */
1547 reg_write(priv, REG_TBG_CNTRL_1, TBG_CNTRL_1_DWIN_DIS);
1548 reg_clear(priv, REG_TX33, TX33_HDMI);
1549 reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(0));
1550
1551 /* no pre-filter or interpolator: */
1552 reg_write(priv, REG_HVF_CNTRL_0, HVF_CNTRL_0_PREFIL(0) |
1553 HVF_CNTRL_0_INTPOL(0));
1554 reg_set(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_PREFILT);
1555 reg_write(priv, REG_VIP_CNTRL_5, VIP_CNTRL_5_SP_CNT(0));
1556 reg_write(priv, REG_VIP_CNTRL_4, VIP_CNTRL_4_BLANKIT(0) |
1557 VIP_CNTRL_4_BLC(0));
1558
1559 reg_clear(priv, REG_PLL_SERIAL_1, PLL_SERIAL_1_SRL_MAN_IZ);
1560 reg_clear(priv, REG_PLL_SERIAL_3, PLL_SERIAL_3_SRL_CCIR |
1561 PLL_SERIAL_3_SRL_DE);
1562 reg_write(priv, REG_SERIALIZER, 0);
1563 reg_write(priv, REG_HVF_CNTRL_1, HVF_CNTRL_1_VQR(0));
1564
1565 reg_write(priv, REG_RPT_CNTRL, RPT_CNTRL_REPEAT(rep));
1566 reg_write(priv, REG_SEL_CLK, sel_clk);
1567 reg_write(priv, REG_PLL_SERIAL_2, PLL_SERIAL_2_SRL_NOSC(div) |
1568 PLL_SERIAL_2_SRL_PR(rep));
1569
1570 /* set color matrix according to output rgb quant range */
1571 if (priv->rgb_quant_range == HDMI_QUANTIZATION_RANGE_LIMITED) {
1572 static u8 tda998x_full_to_limited_range[] = {
1573 MAT_CONTRL_MAT_SC(2),
1574 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
1575 0x03, 0x6f, 0x00, 0x00, 0x00, 0x00,
1576 0x00, 0x00, 0x03, 0x6f, 0x00, 0x00,
1577 0x00, 0x00, 0x00, 0x00, 0x03, 0x6f,
1578 0x00, 0x40, 0x00, 0x40, 0x00, 0x40
1579 };
1580 reg_clear(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_CSC);
1581 reg_write_range(priv, REG_MAT_CONTRL,
1582 tda998x_full_to_limited_range,
1583 sizeof(tda998x_full_to_limited_range));
1584 } else {
1585 reg_write(priv, REG_MAT_CONTRL, MAT_CONTRL_MAT_BP |
1586 MAT_CONTRL_MAT_SC(1));
1587 reg_set(priv, REG_FEAT_POWERDOWN, FEAT_POWERDOWN_CSC);
1588 }
1589
1590 /* set BIAS tmds value: */
1591 reg_write(priv, REG_ANA_GENERAL, 0x09);
1592
1593 /*
1594 * Sync on rising HSYNC/VSYNC
1595 */
1596 reg = VIP_CNTRL_3_SYNC_HS;
1597
1598 /*
1599 * TDA19988 requires high-active sync at input stage,
1600 * so invert low-active sync provided by master encoder here
1601 */
1602 if (mode->flags & DRM_MODE_FLAG_NHSYNC)
1603 reg |= VIP_CNTRL_3_H_TGL;
1604 if (mode->flags & DRM_MODE_FLAG_NVSYNC)
1605 reg |= VIP_CNTRL_3_V_TGL;
1606 reg_write(priv, REG_VIP_CNTRL_3, reg);
1607
1608 reg_write(priv, REG_VIDFORMAT, 0x00);
1609 reg_write16(priv, REG_REFPIX_MSB, ref_pix);
1610 reg_write16(priv, REG_REFLINE_MSB, ref_line);
1611 reg_write16(priv, REG_NPIX_MSB, n_pix);
1612 reg_write16(priv, REG_NLINE_MSB, n_line);
1613 reg_write16(priv, REG_VS_LINE_STRT_1_MSB, vs1_line_s);
1614 reg_write16(priv, REG_VS_PIX_STRT_1_MSB, vs1_pix_s);
1615 reg_write16(priv, REG_VS_LINE_END_1_MSB, vs1_line_e);
1616 reg_write16(priv, REG_VS_PIX_END_1_MSB, vs1_pix_e);
1617 reg_write16(priv, REG_VS_LINE_STRT_2_MSB, vs2_line_s);
1618 reg_write16(priv, REG_VS_PIX_STRT_2_MSB, vs2_pix_s);
1619 reg_write16(priv, REG_VS_LINE_END_2_MSB, vs2_line_e);
1620 reg_write16(priv, REG_VS_PIX_END_2_MSB, vs2_pix_e);
1621 reg_write16(priv, REG_HS_PIX_START_MSB, hs_pix_s);
1622 reg_write16(priv, REG_HS_PIX_STOP_MSB, hs_pix_e);
1623 reg_write16(priv, REG_VWIN_START_1_MSB, vwin1_line_s);
1624 reg_write16(priv, REG_VWIN_END_1_MSB, vwin1_line_e);
1625 reg_write16(priv, REG_VWIN_START_2_MSB, vwin2_line_s);
1626 reg_write16(priv, REG_VWIN_END_2_MSB, vwin2_line_e);
1627 reg_write16(priv, REG_DE_START_MSB, de_pix_s);
1628 reg_write16(priv, REG_DE_STOP_MSB, de_pix_e);
1629
1630 if (priv->rev == TDA19988) {
1631 /* let incoming pixels fill the active space (if any) */
1632 reg_write(priv, REG_ENABLE_SPACE, 0x00);
1633 }
1634
1635 /*
1636 * Always generate sync polarity relative to input sync and
1637 * revert input stage toggled sync at output stage
1638 */
1639 reg = TBG_CNTRL_1_DWIN_DIS | TBG_CNTRL_1_TGL_EN;
1640 if (mode->flags & DRM_MODE_FLAG_NHSYNC)
1641 reg |= TBG_CNTRL_1_H_TGL;
1642 if (mode->flags & DRM_MODE_FLAG_NVSYNC)
1643 reg |= TBG_CNTRL_1_V_TGL;
1644 reg_write(priv, REG_TBG_CNTRL_1, reg);
1645
1646 /* must be last register set: */
1647 reg_write(priv, REG_TBG_CNTRL_0, 0);
1648
1649 /* CEA-861B section 6 says that:
1650 * CEA version 1 (CEA-861) has no support for infoframes.
1651 * CEA version 2 (CEA-861A) supports version 1 AVI infoframes,
1652 * and optional basic audio.
1653 * CEA version 3 (CEA-861B) supports version 1 and 2 AVI infoframes,
1654 * and optional digital audio, with audio infoframes.
1655 *
1656 * Since we only support generation of version 2 AVI infoframes,
1657 * ignore CEA version 2 and below (iow, behave as if we're a
1658 * CEA-861 source.)
1659 */
1660 priv->supports_infoframes = priv->connector.display_info.cea_rev >= 3;
1661
1662 if (priv->supports_infoframes) {
1663 /* We need to turn HDMI HDCP stuff on to get audio through */
1664 reg &= ~TBG_CNTRL_1_DWIN_DIS;
1665 reg_write(priv, REG_TBG_CNTRL_1, reg);
1666 reg_write(priv, REG_ENC_CNTRL, ENC_CNTRL_CTL_CODE(1));
1667 reg_set(priv, REG_TX33, TX33_HDMI);
1668
1669 tda998x_write_avi(priv, adjusted_mode);
1670 tda998x_write_vsi(priv, adjusted_mode);
1671
1672 if (priv->sink_has_audio)
1673 tda998x_configure_audio(priv);
1674 }
1675
1676 mutex_unlock(&priv->audio_mutex);
1677 }
1678
1679 static const struct drm_bridge_funcs tda998x_bridge_funcs = {
1680 .attach = tda998x_bridge_attach,
1681 .detach = tda998x_bridge_detach,
1682 .mode_valid = tda998x_bridge_mode_valid,
1683 .disable = tda998x_bridge_disable,
1684 .mode_set = tda998x_bridge_mode_set,
1685 .enable = tda998x_bridge_enable,
1686 };
1687
1688 /* I2C driver functions */
1689
tda998x_get_audio_ports(struct tda998x_priv * priv,struct device_node * np)1690 static int tda998x_get_audio_ports(struct tda998x_priv *priv,
1691 struct device_node *np)
1692 {
1693 const u32 *port_data;
1694 u32 size;
1695 int i;
1696
1697 port_data = of_get_property(np, "audio-ports", &size);
1698 if (!port_data)
1699 return 0;
1700
1701 size /= sizeof(u32);
1702 if (size > 2 * ARRAY_SIZE(priv->audio_port_enable) || size % 2 != 0) {
1703 dev_err(&priv->hdmi->dev,
1704 "Bad number of elements in audio-ports dt-property\n");
1705 return -EINVAL;
1706 }
1707
1708 size /= 2;
1709
1710 for (i = 0; i < size; i++) {
1711 unsigned int route;
1712 u8 afmt = be32_to_cpup(&port_data[2*i]);
1713 u8 ena_ap = be32_to_cpup(&port_data[2*i+1]);
1714
1715 switch (afmt) {
1716 case AFMT_I2S:
1717 route = AUDIO_ROUTE_I2S;
1718 break;
1719 case AFMT_SPDIF:
1720 route = AUDIO_ROUTE_SPDIF;
1721 break;
1722 default:
1723 dev_err(&priv->hdmi->dev,
1724 "Bad audio format %u\n", afmt);
1725 return -EINVAL;
1726 }
1727
1728 if (!ena_ap) {
1729 dev_err(&priv->hdmi->dev, "invalid zero port config\n");
1730 continue;
1731 }
1732
1733 if (priv->audio_port_enable[route]) {
1734 dev_err(&priv->hdmi->dev,
1735 "%s format already configured\n",
1736 route == AUDIO_ROUTE_SPDIF ? "SPDIF" : "I2S");
1737 return -EINVAL;
1738 }
1739
1740 priv->audio_port_enable[route] = ena_ap;
1741 }
1742 return 0;
1743 }
1744
tda998x_set_config(struct tda998x_priv * priv,const struct tda998x_encoder_params * p)1745 static int tda998x_set_config(struct tda998x_priv *priv,
1746 const struct tda998x_encoder_params *p)
1747 {
1748 priv->vip_cntrl_0 = VIP_CNTRL_0_SWAP_A(p->swap_a) |
1749 (p->mirr_a ? VIP_CNTRL_0_MIRR_A : 0) |
1750 VIP_CNTRL_0_SWAP_B(p->swap_b) |
1751 (p->mirr_b ? VIP_CNTRL_0_MIRR_B : 0);
1752 priv->vip_cntrl_1 = VIP_CNTRL_1_SWAP_C(p->swap_c) |
1753 (p->mirr_c ? VIP_CNTRL_1_MIRR_C : 0) |
1754 VIP_CNTRL_1_SWAP_D(p->swap_d) |
1755 (p->mirr_d ? VIP_CNTRL_1_MIRR_D : 0);
1756 priv->vip_cntrl_2 = VIP_CNTRL_2_SWAP_E(p->swap_e) |
1757 (p->mirr_e ? VIP_CNTRL_2_MIRR_E : 0) |
1758 VIP_CNTRL_2_SWAP_F(p->swap_f) |
1759 (p->mirr_f ? VIP_CNTRL_2_MIRR_F : 0);
1760
1761 if (p->audio_params.format != AFMT_UNUSED) {
1762 unsigned int ratio, route;
1763 bool spdif = p->audio_params.format == AFMT_SPDIF;
1764
1765 route = AUDIO_ROUTE_I2S + spdif;
1766
1767 priv->audio.route = &tda998x_audio_route[route];
1768 priv->audio.cea = p->audio_params.cea;
1769 priv->audio.sample_rate = p->audio_params.sample_rate;
1770 memcpy(priv->audio.status, p->audio_params.status,
1771 min(sizeof(priv->audio.status),
1772 sizeof(p->audio_params.status)));
1773 priv->audio.ena_ap = p->audio_params.config;
1774 priv->audio.i2s_format = I2S_FORMAT_PHILIPS;
1775
1776 ratio = spdif ? 64 : p->audio_params.sample_width * 2;
1777 return tda998x_derive_cts_n(priv, &priv->audio, ratio);
1778 }
1779
1780 return 0;
1781 }
1782
tda998x_destroy(struct device * dev)1783 static void tda998x_destroy(struct device *dev)
1784 {
1785 struct tda998x_priv *priv = dev_get_drvdata(dev);
1786
1787 drm_bridge_remove(&priv->bridge);
1788
1789 /* disable all IRQs and free the IRQ handler */
1790 cec_write(priv, REG_CEC_RXSHPDINTENA, 0);
1791 reg_clear(priv, REG_INT_FLAGS_2, INT_FLAGS_2_EDID_BLK_RD);
1792
1793 if (priv->audio_pdev)
1794 platform_device_unregister(priv->audio_pdev);
1795
1796 if (priv->hdmi->irq)
1797 free_irq(priv->hdmi->irq, priv);
1798
1799 del_timer_sync(&priv->edid_delay_timer);
1800 cancel_work_sync(&priv->detect_work);
1801
1802 i2c_unregister_device(priv->cec);
1803
1804 cec_notifier_conn_unregister(priv->cec_notify);
1805 }
1806
tda998x_create(struct device * dev)1807 static int tda998x_create(struct device *dev)
1808 {
1809 struct i2c_client *client = to_i2c_client(dev);
1810 struct device_node *np = client->dev.of_node;
1811 struct i2c_board_info cec_info;
1812 struct tda998x_priv *priv;
1813 u32 video;
1814 int rev_lo, rev_hi, ret;
1815
1816 priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
1817 if (!priv)
1818 return -ENOMEM;
1819
1820 dev_set_drvdata(dev, priv);
1821
1822 mutex_init(&priv->mutex); /* protect the page access */
1823 mutex_init(&priv->audio_mutex); /* protect access from audio thread */
1824 mutex_init(&priv->edid_mutex);
1825 INIT_LIST_HEAD(&priv->bridge.list);
1826 init_waitqueue_head(&priv->edid_delay_waitq);
1827 timer_setup(&priv->edid_delay_timer, tda998x_edid_delay_done, 0);
1828 INIT_WORK(&priv->detect_work, tda998x_detect_work);
1829
1830 priv->vip_cntrl_0 = VIP_CNTRL_0_SWAP_A(2) | VIP_CNTRL_0_SWAP_B(3);
1831 priv->vip_cntrl_1 = VIP_CNTRL_1_SWAP_C(0) | VIP_CNTRL_1_SWAP_D(1);
1832 priv->vip_cntrl_2 = VIP_CNTRL_2_SWAP_E(4) | VIP_CNTRL_2_SWAP_F(5);
1833
1834 /* CEC I2C address bound to TDA998x I2C addr by configuration pins */
1835 priv->cec_addr = 0x34 + (client->addr & 0x03);
1836 priv->current_page = 0xff;
1837 priv->hdmi = client;
1838
1839 /* wake up the device: */
1840 cec_write(priv, REG_CEC_ENAMODS,
1841 CEC_ENAMODS_EN_RXSENS | CEC_ENAMODS_EN_HDMI);
1842
1843 tda998x_reset(priv);
1844
1845 /* read version: */
1846 rev_lo = reg_read(priv, REG_VERSION_LSB);
1847 if (rev_lo < 0) {
1848 dev_err(dev, "failed to read version: %d\n", rev_lo);
1849 return rev_lo;
1850 }
1851
1852 rev_hi = reg_read(priv, REG_VERSION_MSB);
1853 if (rev_hi < 0) {
1854 dev_err(dev, "failed to read version: %d\n", rev_hi);
1855 return rev_hi;
1856 }
1857
1858 priv->rev = rev_lo | rev_hi << 8;
1859
1860 /* mask off feature bits: */
1861 priv->rev &= ~0x30; /* not-hdcp and not-scalar bit */
1862
1863 switch (priv->rev) {
1864 case TDA9989N2:
1865 dev_info(dev, "found TDA9989 n2");
1866 break;
1867 case TDA19989:
1868 dev_info(dev, "found TDA19989");
1869 break;
1870 case TDA19989N2:
1871 dev_info(dev, "found TDA19989 n2");
1872 break;
1873 case TDA19988:
1874 dev_info(dev, "found TDA19988");
1875 break;
1876 default:
1877 dev_err(dev, "found unsupported device: %04x\n", priv->rev);
1878 return -ENXIO;
1879 }
1880
1881 /* after reset, enable DDC: */
1882 reg_write(priv, REG_DDC_DISABLE, 0x00);
1883
1884 /* set clock on DDC channel: */
1885 reg_write(priv, REG_TX3, 39);
1886
1887 /* if necessary, disable multi-master: */
1888 if (priv->rev == TDA19989)
1889 reg_set(priv, REG_I2C_MASTER, I2C_MASTER_DIS_MM);
1890
1891 cec_write(priv, REG_CEC_FRO_IM_CLK_CTRL,
1892 CEC_FRO_IM_CLK_CTRL_GHOST_DIS | CEC_FRO_IM_CLK_CTRL_IMCLK_SEL);
1893
1894 /* ensure interrupts are disabled */
1895 cec_write(priv, REG_CEC_RXSHPDINTENA, 0);
1896
1897 /* clear pending interrupts */
1898 cec_read(priv, REG_CEC_RXSHPDINT);
1899 reg_read(priv, REG_INT_FLAGS_0);
1900 reg_read(priv, REG_INT_FLAGS_1);
1901 reg_read(priv, REG_INT_FLAGS_2);
1902
1903 /* initialize the optional IRQ */
1904 if (client->irq) {
1905 unsigned long irq_flags;
1906
1907 /* init read EDID waitqueue and HDP work */
1908 init_waitqueue_head(&priv->wq_edid);
1909
1910 irq_flags =
1911 irqd_get_trigger_type(irq_get_irq_data(client->irq));
1912
1913 priv->cec_glue.irq_flags = irq_flags;
1914
1915 irq_flags |= IRQF_SHARED | IRQF_ONESHOT;
1916 ret = request_threaded_irq(client->irq, NULL,
1917 tda998x_irq_thread, irq_flags,
1918 "tda998x", priv);
1919 if (ret) {
1920 dev_err(dev, "failed to request IRQ#%u: %d\n",
1921 client->irq, ret);
1922 goto err_irq;
1923 }
1924
1925 /* enable HPD irq */
1926 cec_write(priv, REG_CEC_RXSHPDINTENA, CEC_RXSHPDLEV_HPD);
1927 }
1928
1929 priv->cec_notify = cec_notifier_conn_register(dev, NULL, NULL);
1930 if (!priv->cec_notify) {
1931 ret = -ENOMEM;
1932 goto fail;
1933 }
1934
1935 priv->cec_glue.parent = dev;
1936 priv->cec_glue.data = priv;
1937 priv->cec_glue.init = tda998x_cec_hook_init;
1938 priv->cec_glue.exit = tda998x_cec_hook_exit;
1939 priv->cec_glue.open = tda998x_cec_hook_open;
1940 priv->cec_glue.release = tda998x_cec_hook_release;
1941
1942 /*
1943 * Some TDA998x are actually two I2C devices merged onto one piece
1944 * of silicon: TDA9989 and TDA19989 combine the HDMI transmitter
1945 * with a slightly modified TDA9950 CEC device. The CEC device
1946 * is at the TDA9950 address, with the address pins strapped across
1947 * to the TDA998x address pins. Hence, it always has the same
1948 * offset.
1949 */
1950 memset(&cec_info, 0, sizeof(cec_info));
1951 strlcpy(cec_info.type, "tda9950", sizeof(cec_info.type));
1952 cec_info.addr = priv->cec_addr;
1953 cec_info.platform_data = &priv->cec_glue;
1954 cec_info.irq = client->irq;
1955
1956 priv->cec = i2c_new_client_device(client->adapter, &cec_info);
1957 if (IS_ERR(priv->cec)) {
1958 ret = PTR_ERR(priv->cec);
1959 goto fail;
1960 }
1961
1962 /* enable EDID read irq: */
1963 reg_set(priv, REG_INT_FLAGS_2, INT_FLAGS_2_EDID_BLK_RD);
1964
1965 if (np) {
1966 /* get the device tree parameters */
1967 ret = of_property_read_u32(np, "video-ports", &video);
1968 if (ret == 0) {
1969 priv->vip_cntrl_0 = video >> 16;
1970 priv->vip_cntrl_1 = video >> 8;
1971 priv->vip_cntrl_2 = video;
1972 }
1973
1974 ret = tda998x_get_audio_ports(priv, np);
1975 if (ret)
1976 goto fail;
1977
1978 if (priv->audio_port_enable[AUDIO_ROUTE_I2S] ||
1979 priv->audio_port_enable[AUDIO_ROUTE_SPDIF])
1980 tda998x_audio_codec_init(priv, &client->dev);
1981 } else if (dev->platform_data) {
1982 ret = tda998x_set_config(priv, dev->platform_data);
1983 if (ret)
1984 goto fail;
1985 }
1986
1987 priv->bridge.funcs = &tda998x_bridge_funcs;
1988 #ifdef CONFIG_OF
1989 priv->bridge.of_node = dev->of_node;
1990 #endif
1991
1992 drm_bridge_add(&priv->bridge);
1993
1994 return 0;
1995
1996 fail:
1997 tda998x_destroy(dev);
1998 err_irq:
1999 return ret;
2000 }
2001
2002 /* DRM encoder functions */
2003
tda998x_encoder_init(struct device * dev,struct drm_device * drm)2004 static int tda998x_encoder_init(struct device *dev, struct drm_device *drm)
2005 {
2006 struct tda998x_priv *priv = dev_get_drvdata(dev);
2007 u32 crtcs = 0;
2008 int ret;
2009
2010 if (dev->of_node)
2011 crtcs = drm_of_find_possible_crtcs(drm, dev->of_node);
2012
2013 /* If no CRTCs were found, fall back to our old behaviour */
2014 if (crtcs == 0) {
2015 dev_warn(dev, "Falling back to first CRTC\n");
2016 crtcs = 1 << 0;
2017 }
2018
2019 priv->encoder.possible_crtcs = crtcs;
2020
2021 ret = drm_simple_encoder_init(drm, &priv->encoder,
2022 DRM_MODE_ENCODER_TMDS);
2023 if (ret)
2024 goto err_encoder;
2025
2026 ret = drm_bridge_attach(&priv->encoder, &priv->bridge, NULL, 0);
2027 if (ret)
2028 goto err_bridge;
2029
2030 return 0;
2031
2032 err_bridge:
2033 drm_encoder_cleanup(&priv->encoder);
2034 err_encoder:
2035 return ret;
2036 }
2037
tda998x_bind(struct device * dev,struct device * master,void * data)2038 static int tda998x_bind(struct device *dev, struct device *master, void *data)
2039 {
2040 struct drm_device *drm = data;
2041
2042 return tda998x_encoder_init(dev, drm);
2043 }
2044
tda998x_unbind(struct device * dev,struct device * master,void * data)2045 static void tda998x_unbind(struct device *dev, struct device *master,
2046 void *data)
2047 {
2048 struct tda998x_priv *priv = dev_get_drvdata(dev);
2049
2050 drm_encoder_cleanup(&priv->encoder);
2051 }
2052
2053 static const struct component_ops tda998x_ops = {
2054 .bind = tda998x_bind,
2055 .unbind = tda998x_unbind,
2056 };
2057
2058 static int
tda998x_probe(struct i2c_client * client,const struct i2c_device_id * id)2059 tda998x_probe(struct i2c_client *client, const struct i2c_device_id *id)
2060 {
2061 int ret;
2062
2063 if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C)) {
2064 dev_warn(&client->dev, "adapter does not support I2C\n");
2065 return -EIO;
2066 }
2067
2068 ret = tda998x_create(&client->dev);
2069 if (ret)
2070 return ret;
2071
2072 ret = component_add(&client->dev, &tda998x_ops);
2073 if (ret)
2074 tda998x_destroy(&client->dev);
2075 return ret;
2076 }
2077
tda998x_remove(struct i2c_client * client)2078 static int tda998x_remove(struct i2c_client *client)
2079 {
2080 component_del(&client->dev, &tda998x_ops);
2081 tda998x_destroy(&client->dev);
2082 return 0;
2083 }
2084
2085 #ifdef CONFIG_OF
2086 static const struct of_device_id tda998x_dt_ids[] = {
2087 { .compatible = "nxp,tda998x", },
2088 { }
2089 };
2090 MODULE_DEVICE_TABLE(of, tda998x_dt_ids);
2091 #endif
2092
2093 static const struct i2c_device_id tda998x_ids[] = {
2094 { "tda998x", 0 },
2095 { }
2096 };
2097 MODULE_DEVICE_TABLE(i2c, tda998x_ids);
2098
2099 static struct i2c_driver tda998x_driver = {
2100 .probe = tda998x_probe,
2101 .remove = tda998x_remove,
2102 .driver = {
2103 .name = "tda998x",
2104 .of_match_table = of_match_ptr(tda998x_dt_ids),
2105 },
2106 .id_table = tda998x_ids,
2107 };
2108
2109 module_i2c_driver(tda998x_driver);
2110
2111 MODULE_AUTHOR("Rob Clark <robdclark@gmail.com");
2112 MODULE_DESCRIPTION("NXP Semiconductors TDA998X HDMI Encoder");
2113 MODULE_LICENSE("GPL");
2114