1# 2# Realtek device configuration 3# 4 5config NET_VENDOR_REALTEK 6 bool "Realtek devices" 7 default y 8 depends on PCI || (PARPORT && X86) 9 ---help--- 10 If you have a network (Ethernet) card belonging to this class, say Y 11 and read the Ethernet-HOWTO, available from 12 <http://www.tldp.org/docs.html#howto>. 13 14 Note that the answer to this question doesn't directly affect the 15 kernel: saying N will just cause the configurator to skip all 16 the questions about Realtek devices. If you say Y, you will be asked for 17 your specific card in the following questions. 18 19if NET_VENDOR_REALTEK 20 21config ATP 22 tristate "AT-LAN-TEC/RealTek pocket adapter support" 23 depends on PARPORT && X86 24 select CRC32 25 ---help--- 26 This is a network (Ethernet) device which attaches to your parallel 27 port. Read <file:drivers/net/ethernet/realtek/atp.c> as well as the 28 Ethernet-HOWTO, available from <http://www.tldp.org/docs.html#howto>, 29 if you want to use this. If you intend to use this driver, you 30 should have said N to the "Parallel printer support", because the two 31 drivers don't like each other. 32 33 To compile this driver as a module, choose M here: the module 34 will be called atp. 35 36config 8139CP 37 tristate "RealTek RTL-8139 C+ PCI Fast Ethernet Adapter support (EXPERIMENTAL)" 38 depends on PCI && EXPERIMENTAL 39 select CRC32 40 select NET_CORE 41 select MII 42 ---help--- 43 This is a driver for the Fast Ethernet PCI network cards based on 44 the RTL8139C+ chips. If you have one of those, say Y and read 45 the Ethernet-HOWTO, available from 46 <http://www.tldp.org/docs.html#howto>. 47 48 To compile this driver as a module, choose M here: the module 49 will be called 8139cp. This is recommended. 50 51config 8139TOO 52 tristate "RealTek RTL-8129/8130/8139 PCI Fast Ethernet Adapter support" 53 depends on PCI 54 select CRC32 55 select NET_CORE 56 select MII 57 ---help--- 58 This is a driver for the Fast Ethernet PCI network cards based on 59 the RTL 8129/8130/8139 chips. If you have one of those, say Y and 60 read the Ethernet-HOWTO <http://www.tldp.org/docs.html#howto>. 61 62 To compile this driver as a module, choose M here: the module 63 will be called 8139too. This is recommended. 64 65config 8139TOO_PIO 66 bool "Use PIO instead of MMIO" 67 default y 68 depends on 8139TOO 69 ---help--- 70 This instructs the driver to use programmed I/O ports (PIO) instead 71 of PCI shared memory (MMIO). This can possibly solve some problems 72 in case your mainboard has memory consistency issues. If unsure, 73 say N. 74 75config 8139TOO_TUNE_TWISTER 76 bool "Support for uncommon RTL-8139 rev. K (automatic channel equalization)" 77 depends on 8139TOO 78 ---help--- 79 This implements a function which might come in handy in case you 80 are using low quality on long cabling. It is required for RealTek 81 RTL-8139 revision K boards, and totally unused otherwise. It tries 82 to match the transceiver to the cable characteristics. This is 83 experimental since hardly documented by the manufacturer. 84 If unsure, say Y. 85 86config 8139TOO_8129 87 bool "Support for older RTL-8129/8130 boards" 88 depends on 8139TOO 89 ---help--- 90 This enables support for the older and uncommon RTL-8129 and 91 RTL-8130 chips, which support MII via an external transceiver, 92 instead of an internal one. Disabling this option will save some 93 memory by making the code size smaller. If unsure, say Y. 94 95config 8139_OLD_RX_RESET 96 bool "Use older RX-reset method" 97 depends on 8139TOO 98 ---help--- 99 The 8139too driver was recently updated to contain a more rapid 100 reset sequence, in the face of severe receive errors. This "new" 101 RX-reset method should be adequate for all boards. But if you 102 experience problems, you can enable this option to restore the 103 old RX-reset behavior. If unsure, say N. 104 105config R8169 106 tristate "Realtek 8169 gigabit ethernet support" 107 depends on PCI 108 select FW_LOADER 109 select CRC32 110 select NET_CORE 111 select MII 112 ---help--- 113 Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter. 114 115 To compile this driver as a module, choose M here: the module 116 will be called r8169. This is recommended. 117 118endif # NET_VENDOR_REALTEK 119