1 /*
2 *
3 * arch/arm/mach-u300/timer.c
4 *
5 *
6 * Copyright (C) 2007-2009 ST-Ericsson AB
7 * License terms: GNU General Public License (GPL) version 2
8 * Timer COH 901 328, runs the OS timer interrupt.
9 * Author: Linus Walleij <linus.walleij@stericsson.com>
10 */
11 #include <linux/interrupt.h>
12 #include <linux/time.h>
13 #include <linux/timex.h>
14 #include <linux/clockchips.h>
15 #include <linux/clocksource.h>
16 #include <linux/types.h>
17 #include <linux/io.h>
18 #include <linux/clk.h>
19 #include <linux/err.h>
20
21 #include <mach/hardware.h>
22
23 /* Generic stuff */
24 #include <asm/sched_clock.h>
25 #include <asm/mach/map.h>
26 #include <asm/mach/time.h>
27 #include <asm/mach/irq.h>
28
29 /*
30 * APP side special timer registers
31 * This timer contains four timers which can fire an interrupt each.
32 * OS (operating system) timer @ 32768 Hz
33 * DD (device driver) timer @ 1 kHz
34 * GP1 (general purpose 1) timer @ 1MHz
35 * GP2 (general purpose 2) timer @ 1MHz
36 */
37
38 /* Reset OS Timer 32bit (-/W) */
39 #define U300_TIMER_APP_ROST (0x0000)
40 #define U300_TIMER_APP_ROST_TIMER_RESET (0x00000000)
41 /* Enable OS Timer 32bit (-/W) */
42 #define U300_TIMER_APP_EOST (0x0004)
43 #define U300_TIMER_APP_EOST_TIMER_ENABLE (0x00000000)
44 /* Disable OS Timer 32bit (-/W) */
45 #define U300_TIMER_APP_DOST (0x0008)
46 #define U300_TIMER_APP_DOST_TIMER_DISABLE (0x00000000)
47 /* OS Timer Mode Register 32bit (-/W) */
48 #define U300_TIMER_APP_SOSTM (0x000c)
49 #define U300_TIMER_APP_SOSTM_MODE_CONTINUOUS (0x00000000)
50 #define U300_TIMER_APP_SOSTM_MODE_ONE_SHOT (0x00000001)
51 /* OS Timer Status Register 32bit (R/-) */
52 #define U300_TIMER_APP_OSTS (0x0010)
53 #define U300_TIMER_APP_OSTS_TIMER_STATE_MASK (0x0000000F)
54 #define U300_TIMER_APP_OSTS_TIMER_STATE_IDLE (0x00000001)
55 #define U300_TIMER_APP_OSTS_TIMER_STATE_ACTIVE (0x00000002)
56 #define U300_TIMER_APP_OSTS_ENABLE_IND (0x00000010)
57 #define U300_TIMER_APP_OSTS_MODE_MASK (0x00000020)
58 #define U300_TIMER_APP_OSTS_MODE_CONTINUOUS (0x00000000)
59 #define U300_TIMER_APP_OSTS_MODE_ONE_SHOT (0x00000020)
60 #define U300_TIMER_APP_OSTS_IRQ_ENABLED_IND (0x00000040)
61 #define U300_TIMER_APP_OSTS_IRQ_PENDING_IND (0x00000080)
62 /* OS Timer Current Count Register 32bit (R/-) */
63 #define U300_TIMER_APP_OSTCC (0x0014)
64 /* OS Timer Terminal Count Register 32bit (R/W) */
65 #define U300_TIMER_APP_OSTTC (0x0018)
66 /* OS Timer Interrupt Enable Register 32bit (-/W) */
67 #define U300_TIMER_APP_OSTIE (0x001c)
68 #define U300_TIMER_APP_OSTIE_IRQ_DISABLE (0x00000000)
69 #define U300_TIMER_APP_OSTIE_IRQ_ENABLE (0x00000001)
70 /* OS Timer Interrupt Acknowledge Register 32bit (-/W) */
71 #define U300_TIMER_APP_OSTIA (0x0020)
72 #define U300_TIMER_APP_OSTIA_IRQ_ACK (0x00000080)
73
74 /* Reset DD Timer 32bit (-/W) */
75 #define U300_TIMER_APP_RDDT (0x0040)
76 #define U300_TIMER_APP_RDDT_TIMER_RESET (0x00000000)
77 /* Enable DD Timer 32bit (-/W) */
78 #define U300_TIMER_APP_EDDT (0x0044)
79 #define U300_TIMER_APP_EDDT_TIMER_ENABLE (0x00000000)
80 /* Disable DD Timer 32bit (-/W) */
81 #define U300_TIMER_APP_DDDT (0x0048)
82 #define U300_TIMER_APP_DDDT_TIMER_DISABLE (0x00000000)
83 /* DD Timer Mode Register 32bit (-/W) */
84 #define U300_TIMER_APP_SDDTM (0x004c)
85 #define U300_TIMER_APP_SDDTM_MODE_CONTINUOUS (0x00000000)
86 #define U300_TIMER_APP_SDDTM_MODE_ONE_SHOT (0x00000001)
87 /* DD Timer Status Register 32bit (R/-) */
88 #define U300_TIMER_APP_DDTS (0x0050)
89 #define U300_TIMER_APP_DDTS_TIMER_STATE_MASK (0x0000000F)
90 #define U300_TIMER_APP_DDTS_TIMER_STATE_IDLE (0x00000001)
91 #define U300_TIMER_APP_DDTS_TIMER_STATE_ACTIVE (0x00000002)
92 #define U300_TIMER_APP_DDTS_ENABLE_IND (0x00000010)
93 #define U300_TIMER_APP_DDTS_MODE_MASK (0x00000020)
94 #define U300_TIMER_APP_DDTS_MODE_CONTINUOUS (0x00000000)
95 #define U300_TIMER_APP_DDTS_MODE_ONE_SHOT (0x00000020)
96 #define U300_TIMER_APP_DDTS_IRQ_ENABLED_IND (0x00000040)
97 #define U300_TIMER_APP_DDTS_IRQ_PENDING_IND (0x00000080)
98 /* DD Timer Current Count Register 32bit (R/-) */
99 #define U300_TIMER_APP_DDTCC (0x0054)
100 /* DD Timer Terminal Count Register 32bit (R/W) */
101 #define U300_TIMER_APP_DDTTC (0x0058)
102 /* DD Timer Interrupt Enable Register 32bit (-/W) */
103 #define U300_TIMER_APP_DDTIE (0x005c)
104 #define U300_TIMER_APP_DDTIE_IRQ_DISABLE (0x00000000)
105 #define U300_TIMER_APP_DDTIE_IRQ_ENABLE (0x00000001)
106 /* DD Timer Interrupt Acknowledge Register 32bit (-/W) */
107 #define U300_TIMER_APP_DDTIA (0x0060)
108 #define U300_TIMER_APP_DDTIA_IRQ_ACK (0x00000080)
109
110 /* Reset GP1 Timer 32bit (-/W) */
111 #define U300_TIMER_APP_RGPT1 (0x0080)
112 #define U300_TIMER_APP_RGPT1_TIMER_RESET (0x00000000)
113 /* Enable GP1 Timer 32bit (-/W) */
114 #define U300_TIMER_APP_EGPT1 (0x0084)
115 #define U300_TIMER_APP_EGPT1_TIMER_ENABLE (0x00000000)
116 /* Disable GP1 Timer 32bit (-/W) */
117 #define U300_TIMER_APP_DGPT1 (0x0088)
118 #define U300_TIMER_APP_DGPT1_TIMER_DISABLE (0x00000000)
119 /* GP1 Timer Mode Register 32bit (-/W) */
120 #define U300_TIMER_APP_SGPT1M (0x008c)
121 #define U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS (0x00000000)
122 #define U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT (0x00000001)
123 /* GP1 Timer Status Register 32bit (R/-) */
124 #define U300_TIMER_APP_GPT1S (0x0090)
125 #define U300_TIMER_APP_GPT1S_TIMER_STATE_MASK (0x0000000F)
126 #define U300_TIMER_APP_GPT1S_TIMER_STATE_IDLE (0x00000001)
127 #define U300_TIMER_APP_GPT1S_TIMER_STATE_ACTIVE (0x00000002)
128 #define U300_TIMER_APP_GPT1S_ENABLE_IND (0x00000010)
129 #define U300_TIMER_APP_GPT1S_MODE_MASK (0x00000020)
130 #define U300_TIMER_APP_GPT1S_MODE_CONTINUOUS (0x00000000)
131 #define U300_TIMER_APP_GPT1S_MODE_ONE_SHOT (0x00000020)
132 #define U300_TIMER_APP_GPT1S_IRQ_ENABLED_IND (0x00000040)
133 #define U300_TIMER_APP_GPT1S_IRQ_PENDING_IND (0x00000080)
134 /* GP1 Timer Current Count Register 32bit (R/-) */
135 #define U300_TIMER_APP_GPT1CC (0x0094)
136 /* GP1 Timer Terminal Count Register 32bit (R/W) */
137 #define U300_TIMER_APP_GPT1TC (0x0098)
138 /* GP1 Timer Interrupt Enable Register 32bit (-/W) */
139 #define U300_TIMER_APP_GPT1IE (0x009c)
140 #define U300_TIMER_APP_GPT1IE_IRQ_DISABLE (0x00000000)
141 #define U300_TIMER_APP_GPT1IE_IRQ_ENABLE (0x00000001)
142 /* GP1 Timer Interrupt Acknowledge Register 32bit (-/W) */
143 #define U300_TIMER_APP_GPT1IA (0x00a0)
144 #define U300_TIMER_APP_GPT1IA_IRQ_ACK (0x00000080)
145
146 /* Reset GP2 Timer 32bit (-/W) */
147 #define U300_TIMER_APP_RGPT2 (0x00c0)
148 #define U300_TIMER_APP_RGPT2_TIMER_RESET (0x00000000)
149 /* Enable GP2 Timer 32bit (-/W) */
150 #define U300_TIMER_APP_EGPT2 (0x00c4)
151 #define U300_TIMER_APP_EGPT2_TIMER_ENABLE (0x00000000)
152 /* Disable GP2 Timer 32bit (-/W) */
153 #define U300_TIMER_APP_DGPT2 (0x00c8)
154 #define U300_TIMER_APP_DGPT2_TIMER_DISABLE (0x00000000)
155 /* GP2 Timer Mode Register 32bit (-/W) */
156 #define U300_TIMER_APP_SGPT2M (0x00cc)
157 #define U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS (0x00000000)
158 #define U300_TIMER_APP_SGPT2M_MODE_ONE_SHOT (0x00000001)
159 /* GP2 Timer Status Register 32bit (R/-) */
160 #define U300_TIMER_APP_GPT2S (0x00d0)
161 #define U300_TIMER_APP_GPT2S_TIMER_STATE_MASK (0x0000000F)
162 #define U300_TIMER_APP_GPT2S_TIMER_STATE_IDLE (0x00000001)
163 #define U300_TIMER_APP_GPT2S_TIMER_STATE_ACTIVE (0x00000002)
164 #define U300_TIMER_APP_GPT2S_ENABLE_IND (0x00000010)
165 #define U300_TIMER_APP_GPT2S_MODE_MASK (0x00000020)
166 #define U300_TIMER_APP_GPT2S_MODE_CONTINUOUS (0x00000000)
167 #define U300_TIMER_APP_GPT2S_MODE_ONE_SHOT (0x00000020)
168 #define U300_TIMER_APP_GPT2S_IRQ_ENABLED_IND (0x00000040)
169 #define U300_TIMER_APP_GPT2S_IRQ_PENDING_IND (0x00000080)
170 /* GP2 Timer Current Count Register 32bit (R/-) */
171 #define U300_TIMER_APP_GPT2CC (0x00d4)
172 /* GP2 Timer Terminal Count Register 32bit (R/W) */
173 #define U300_TIMER_APP_GPT2TC (0x00d8)
174 /* GP2 Timer Interrupt Enable Register 32bit (-/W) */
175 #define U300_TIMER_APP_GPT2IE (0x00dc)
176 #define U300_TIMER_APP_GPT2IE_IRQ_DISABLE (0x00000000)
177 #define U300_TIMER_APP_GPT2IE_IRQ_ENABLE (0x00000001)
178 /* GP2 Timer Interrupt Acknowledge Register 32bit (-/W) */
179 #define U300_TIMER_APP_GPT2IA (0x00e0)
180 #define U300_TIMER_APP_GPT2IA_IRQ_ACK (0x00000080)
181
182 /* Clock request control register - all four timers */
183 #define U300_TIMER_APP_CRC (0x100)
184 #define U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE (0x00000001)
185
186 #define TICKS_PER_JIFFY ((CLOCK_TICK_RATE + (HZ/2)) / HZ)
187 #define US_PER_TICK ((1000000 + (HZ/2)) / HZ)
188
189 /*
190 * The u300_set_mode() function is always called first, if we
191 * have oneshot timer active, the oneshot scheduling function
192 * u300_set_next_event() is called immediately after.
193 */
u300_set_mode(enum clock_event_mode mode,struct clock_event_device * evt)194 static void u300_set_mode(enum clock_event_mode mode,
195 struct clock_event_device *evt)
196 {
197 switch (mode) {
198 case CLOCK_EVT_MODE_PERIODIC:
199 /* Disable interrupts on GPT1 */
200 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
201 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
202 /* Disable GP1 while we're reprogramming it. */
203 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
204 U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
205 /*
206 * Set the periodic mode to a certain number of ticks per
207 * jiffy.
208 */
209 writel(TICKS_PER_JIFFY,
210 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC);
211 /*
212 * Set continuous mode, so the timer keeps triggering
213 * interrupts.
214 */
215 writel(U300_TIMER_APP_SGPT1M_MODE_CONTINUOUS,
216 U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M);
217 /* Enable timer interrupts */
218 writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
219 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
220 /* Then enable the OS timer again */
221 writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
222 U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1);
223 break;
224 case CLOCK_EVT_MODE_ONESHOT:
225 /* Just break; here? */
226 /*
227 * The actual event will be programmed by the next event hook,
228 * so we just set a dummy value somewhere at the end of the
229 * universe here.
230 */
231 /* Disable interrupts on GPT1 */
232 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
233 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
234 /* Disable GP1 while we're reprogramming it. */
235 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
236 U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
237 /*
238 * Expire far in the future, u300_set_next_event() will be
239 * called soon...
240 */
241 writel(0xFFFFFFFF, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC);
242 /* We run one shot per tick here! */
243 writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
244 U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M);
245 /* Enable interrupts for this timer */
246 writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
247 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
248 /* Enable timer */
249 writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
250 U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1);
251 break;
252 case CLOCK_EVT_MODE_UNUSED:
253 case CLOCK_EVT_MODE_SHUTDOWN:
254 /* Disable interrupts on GP1 */
255 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
256 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
257 /* Disable GP1 */
258 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
259 U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
260 break;
261 case CLOCK_EVT_MODE_RESUME:
262 /* Ignore this call */
263 break;
264 }
265 }
266
267 /*
268 * The app timer in one shot mode obviously has to be reprogrammed
269 * in EXACTLY this sequence to work properly. Do NOT try to e.g. replace
270 * the interrupt disable + timer disable commands with a reset command,
271 * it will fail miserably. Apparently (and I found this the hard way)
272 * the timer is very sensitive to the instruction order, though you don't
273 * get that impression from the data sheet.
274 */
u300_set_next_event(unsigned long cycles,struct clock_event_device * evt)275 static int u300_set_next_event(unsigned long cycles,
276 struct clock_event_device *evt)
277
278 {
279 /* Disable interrupts on GPT1 */
280 writel(U300_TIMER_APP_GPT1IE_IRQ_DISABLE,
281 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
282 /* Disable GP1 while we're reprogramming it. */
283 writel(U300_TIMER_APP_DGPT1_TIMER_DISABLE,
284 U300_TIMER_APP_VBASE + U300_TIMER_APP_DGPT1);
285 /* Reset the General Purpose timer 1. */
286 writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
287 U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT1);
288 /* IRQ in n * cycles */
289 writel(cycles, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1TC);
290 /*
291 * We run one shot per tick here! (This is necessary to reconfigure,
292 * the timer will tilt if you don't!)
293 */
294 writel(U300_TIMER_APP_SGPT1M_MODE_ONE_SHOT,
295 U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT1M);
296 /* Enable timer interrupts */
297 writel(U300_TIMER_APP_GPT1IE_IRQ_ENABLE,
298 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IE);
299 /* Then enable the OS timer again */
300 writel(U300_TIMER_APP_EGPT1_TIMER_ENABLE,
301 U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT1);
302 return 0;
303 }
304
305
306 /* Use general purpose timer 1 as clock event */
307 static struct clock_event_device clockevent_u300_1mhz = {
308 .name = "GPT1",
309 .rating = 300, /* Reasonably fast and accurate clock event */
310 .features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
311 .set_next_event = u300_set_next_event,
312 .set_mode = u300_set_mode,
313 };
314
315 /* Clock event timer interrupt handler */
u300_timer_interrupt(int irq,void * dev_id)316 static irqreturn_t u300_timer_interrupt(int irq, void *dev_id)
317 {
318 struct clock_event_device *evt = &clockevent_u300_1mhz;
319 /* ACK/Clear timer IRQ for the APP GPT1 Timer */
320 writel(U300_TIMER_APP_GPT1IA_IRQ_ACK,
321 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT1IA);
322 evt->event_handler(evt);
323 return IRQ_HANDLED;
324 }
325
326 static struct irqaction u300_timer_irq = {
327 .name = "U300 Timer Tick",
328 .flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
329 .handler = u300_timer_interrupt,
330 };
331
332 /*
333 * Override the global weak sched_clock symbol with this
334 * local implementation which uses the clocksource to get some
335 * better resolution when scheduling the kernel. We accept that
336 * this wraps around for now, since it is just a relative time
337 * stamp. (Inspired by OMAP implementation.)
338 */
339
u300_read_sched_clock(void)340 static u32 notrace u300_read_sched_clock(void)
341 {
342 return readl(U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2CC);
343 }
344
345
346 /*
347 * This sets up the system timers, clock source and clock event.
348 */
u300_timer_init(void)349 static void __init u300_timer_init(void)
350 {
351 struct clk *clk;
352 unsigned long rate;
353
354 /* Clock the interrupt controller */
355 clk = clk_get_sys("apptimer", NULL);
356 BUG_ON(IS_ERR(clk));
357 clk_enable(clk);
358 rate = clk_get_rate(clk);
359
360 setup_sched_clock(u300_read_sched_clock, 32, rate);
361
362 /*
363 * Disable the "OS" and "DD" timers - these are designed for Symbian!
364 * Example usage in cnh1601578 cpu subsystem pd_timer_app.c
365 */
366 writel(U300_TIMER_APP_CRC_CLOCK_REQUEST_ENABLE,
367 U300_TIMER_APP_VBASE + U300_TIMER_APP_CRC);
368 writel(U300_TIMER_APP_ROST_TIMER_RESET,
369 U300_TIMER_APP_VBASE + U300_TIMER_APP_ROST);
370 writel(U300_TIMER_APP_DOST_TIMER_DISABLE,
371 U300_TIMER_APP_VBASE + U300_TIMER_APP_DOST);
372 writel(U300_TIMER_APP_RDDT_TIMER_RESET,
373 U300_TIMER_APP_VBASE + U300_TIMER_APP_RDDT);
374 writel(U300_TIMER_APP_DDDT_TIMER_DISABLE,
375 U300_TIMER_APP_VBASE + U300_TIMER_APP_DDDT);
376
377 /* Reset the General Purpose timer 1. */
378 writel(U300_TIMER_APP_RGPT1_TIMER_RESET,
379 U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT1);
380
381 /* Set up the IRQ handler */
382 setup_irq(IRQ_U300_TIMER_APP_GP1, &u300_timer_irq);
383
384 /* Reset the General Purpose timer 2 */
385 writel(U300_TIMER_APP_RGPT2_TIMER_RESET,
386 U300_TIMER_APP_VBASE + U300_TIMER_APP_RGPT2);
387 /* Set this timer to run around forever */
388 writel(0xFFFFFFFFU, U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2TC);
389 /* Set continuous mode so it wraps around */
390 writel(U300_TIMER_APP_SGPT2M_MODE_CONTINUOUS,
391 U300_TIMER_APP_VBASE + U300_TIMER_APP_SGPT2M);
392 /* Disable timer interrupts */
393 writel(U300_TIMER_APP_GPT2IE_IRQ_DISABLE,
394 U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2IE);
395 /* Then enable the GP2 timer to use as a free running us counter */
396 writel(U300_TIMER_APP_EGPT2_TIMER_ENABLE,
397 U300_TIMER_APP_VBASE + U300_TIMER_APP_EGPT2);
398
399 /* Use general purpose timer 2 as clock source */
400 if (clocksource_mmio_init(U300_TIMER_APP_VBASE + U300_TIMER_APP_GPT2CC,
401 "GPT2", rate, 300, 32, clocksource_mmio_readl_up))
402 pr_err("timer: failed to initialize U300 clock source\n");
403
404 /* Configure and register the clockevent */
405 clockevents_config_and_register(&clockevent_u300_1mhz, rate,
406 1, 0xffffffff);
407
408 /*
409 * TODO: init and register the rest of the timers too, they can be
410 * used by hrtimers!
411 */
412 }
413
414 /*
415 * Very simple system timer that only register the clock event and
416 * clock source.
417 */
418 struct sys_timer u300_timer = {
419 .init = u300_timer_init,
420 };
421