1 /*
2 * DSM-G600 board-setup
3 *
4 * Copyright (C) 2008 Rod Whitby <rod@whitby.id.au>
5 * Copyright (C) 2006 Tower Technologies
6 *
7 * based on ixdp425-setup.c:
8 * Copyright (C) 2003-2004 MontaVista Software, Inc.
9 * based on nslu2-power.c:
10 * Copyright (C) 2005 Tower Technologies
11 * based on nslu2-io.c:
12 * Copyright (C) 2004 Karen Spearel
13 *
14 * Author: Alessandro Zummo <a.zummo@towertech.it>
15 * Author: Michael Westerhof <mwester@dls.net>
16 * Author: Rod Whitby <rod@whitby.id.au>
17 * Maintainers: http://www.nslu2-linux.org/
18 */
19 #include <linux/gpio.h>
20 #include <linux/irq.h>
21 #include <linux/jiffies.h>
22 #include <linux/timer.h>
23 #include <linux/serial.h>
24 #include <linux/serial_8250.h>
25 #include <linux/leds.h>
26 #include <linux/reboot.h>
27 #include <linux/i2c.h>
28 #include <linux/i2c-gpio.h>
29
30 #include <asm/mach-types.h>
31 #include <asm/mach/arch.h>
32 #include <asm/mach/flash.h>
33 #include <asm/mach/time.h>
34
35 #define DSMG600_SDA_PIN 5
36 #define DSMG600_SCL_PIN 4
37
38 /* DSM-G600 Timer Setting */
39 #define DSMG600_FREQ 66000000
40
41 /* Buttons */
42 #define DSMG600_PB_GPIO 15 /* power button */
43 #define DSMG600_RB_GPIO 3 /* reset button */
44
45 /* Power control */
46 #define DSMG600_PO_GPIO 2 /* power off */
47
48 /* LEDs */
49 #define DSMG600_LED_PWR_GPIO 0
50 #define DSMG600_LED_WLAN_GPIO 14
51
52 static struct flash_platform_data dsmg600_flash_data = {
53 .map_name = "cfi_probe",
54 .width = 2,
55 };
56
57 static struct resource dsmg600_flash_resource = {
58 .flags = IORESOURCE_MEM,
59 };
60
61 static struct platform_device dsmg600_flash = {
62 .name = "IXP4XX-Flash",
63 .id = 0,
64 .dev.platform_data = &dsmg600_flash_data,
65 .num_resources = 1,
66 .resource = &dsmg600_flash_resource,
67 };
68
69 static struct i2c_gpio_platform_data dsmg600_i2c_gpio_data = {
70 .sda_pin = DSMG600_SDA_PIN,
71 .scl_pin = DSMG600_SCL_PIN,
72 };
73
74 static struct platform_device dsmg600_i2c_gpio = {
75 .name = "i2c-gpio",
76 .id = 0,
77 .dev = {
78 .platform_data = &dsmg600_i2c_gpio_data,
79 },
80 };
81
82 static struct i2c_board_info __initdata dsmg600_i2c_board_info [] = {
83 {
84 I2C_BOARD_INFO("pcf8563", 0x51),
85 },
86 };
87
88 static struct gpio_led dsmg600_led_pins[] = {
89 {
90 .name = "dsmg600:green:power",
91 .gpio = DSMG600_LED_PWR_GPIO,
92 },
93 {
94 .name = "dsmg600:green:wlan",
95 .gpio = DSMG600_LED_WLAN_GPIO,
96 .active_low = true,
97 },
98 };
99
100 static struct gpio_led_platform_data dsmg600_led_data = {
101 .num_leds = ARRAY_SIZE(dsmg600_led_pins),
102 .leds = dsmg600_led_pins,
103 };
104
105 static struct platform_device dsmg600_leds = {
106 .name = "leds-gpio",
107 .id = -1,
108 .dev.platform_data = &dsmg600_led_data,
109 };
110
111 static struct resource dsmg600_uart_resources[] = {
112 {
113 .start = IXP4XX_UART1_BASE_PHYS,
114 .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
115 .flags = IORESOURCE_MEM,
116 },
117 {
118 .start = IXP4XX_UART2_BASE_PHYS,
119 .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
120 .flags = IORESOURCE_MEM,
121 }
122 };
123
124 static struct plat_serial8250_port dsmg600_uart_data[] = {
125 {
126 .mapbase = IXP4XX_UART1_BASE_PHYS,
127 .membase = (char *)IXP4XX_UART1_BASE_VIRT + REG_OFFSET,
128 .irq = IRQ_IXP4XX_UART1,
129 .flags = UPF_BOOT_AUTOCONF,
130 .iotype = UPIO_MEM,
131 .regshift = 2,
132 .uartclk = IXP4XX_UART_XTAL,
133 },
134 {
135 .mapbase = IXP4XX_UART2_BASE_PHYS,
136 .membase = (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
137 .irq = IRQ_IXP4XX_UART2,
138 .flags = UPF_BOOT_AUTOCONF,
139 .iotype = UPIO_MEM,
140 .regshift = 2,
141 .uartclk = IXP4XX_UART_XTAL,
142 },
143 { }
144 };
145
146 static struct platform_device dsmg600_uart = {
147 .name = "serial8250",
148 .id = PLAT8250_DEV_PLATFORM,
149 .dev.platform_data = dsmg600_uart_data,
150 .num_resources = ARRAY_SIZE(dsmg600_uart_resources),
151 .resource = dsmg600_uart_resources,
152 };
153
154 static struct platform_device *dsmg600_devices[] __initdata = {
155 &dsmg600_i2c_gpio,
156 &dsmg600_flash,
157 &dsmg600_leds,
158 };
159
dsmg600_power_off(void)160 static void dsmg600_power_off(void)
161 {
162 /* enable the pwr cntl gpio */
163 gpio_line_config(DSMG600_PO_GPIO, IXP4XX_GPIO_OUT);
164
165 /* poweroff */
166 gpio_line_set(DSMG600_PO_GPIO, IXP4XX_GPIO_HIGH);
167 }
168
169 /* This is used to make sure the power-button pusher is serious. The button
170 * must be held until the value of this counter reaches zero.
171 */
172 static int power_button_countdown;
173
174 /* Must hold the button down for at least this many counts to be processed */
175 #define PBUTTON_HOLDDOWN_COUNT 4 /* 2 secs */
176
177 static void dsmg600_power_handler(unsigned long data);
178 static DEFINE_TIMER(dsmg600_power_timer, dsmg600_power_handler, 0, 0);
179
dsmg600_power_handler(unsigned long data)180 static void dsmg600_power_handler(unsigned long data)
181 {
182 /* This routine is called twice per second to check the
183 * state of the power button.
184 */
185
186 if (gpio_get_value(DSMG600_PB_GPIO)) {
187
188 /* IO Pin is 1 (button pushed) */
189 if (power_button_countdown > 0)
190 power_button_countdown--;
191
192 } else {
193
194 /* Done on button release, to allow for auto-power-on mods. */
195 if (power_button_countdown == 0) {
196 /* Signal init to do the ctrlaltdel action,
197 * this will bypass init if it hasn't started
198 * and do a kernel_restart.
199 */
200 ctrl_alt_del();
201
202 /* Change the state of the power LED to "blink" */
203 gpio_line_set(DSMG600_LED_PWR_GPIO, IXP4XX_GPIO_LOW);
204 } else {
205 power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
206 }
207 }
208
209 mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
210 }
211
dsmg600_reset_handler(int irq,void * dev_id)212 static irqreturn_t dsmg600_reset_handler(int irq, void *dev_id)
213 {
214 /* This is the paper-clip reset, it shuts the machine down directly. */
215 machine_power_off();
216
217 return IRQ_HANDLED;
218 }
219
dsmg600_timer_init(void)220 static void __init dsmg600_timer_init(void)
221 {
222 /* The xtal on this machine is non-standard. */
223 ixp4xx_timer_freq = DSMG600_FREQ;
224
225 /* Call standard timer_init function. */
226 ixp4xx_timer_init();
227 }
228
229 static struct sys_timer dsmg600_timer = {
230 .init = dsmg600_timer_init,
231 };
232
dsmg600_init(void)233 static void __init dsmg600_init(void)
234 {
235 ixp4xx_sys_init();
236
237 /* Make sure that GPIO14 and GPIO15 are not used as clocks */
238 *IXP4XX_GPIO_GPCLKR = 0;
239
240 dsmg600_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
241 dsmg600_flash_resource.end =
242 IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
243
244 i2c_register_board_info(0, dsmg600_i2c_board_info,
245 ARRAY_SIZE(dsmg600_i2c_board_info));
246
247 /* The UART is required on the DSM-G600 (Redboot cannot use the
248 * NIC) -- do it here so that it does *not* get removed if
249 * platform_add_devices fails!
250 */
251 (void)platform_device_register(&dsmg600_uart);
252
253 platform_add_devices(dsmg600_devices, ARRAY_SIZE(dsmg600_devices));
254
255 pm_power_off = dsmg600_power_off;
256
257 if (request_irq(gpio_to_irq(DSMG600_RB_GPIO), &dsmg600_reset_handler,
258 IRQF_DISABLED | IRQF_TRIGGER_LOW,
259 "DSM-G600 reset button", NULL) < 0) {
260
261 printk(KERN_DEBUG "Reset Button IRQ %d not available\n",
262 gpio_to_irq(DSMG600_RB_GPIO));
263 }
264
265 /* The power button on the D-Link DSM-G600 is on GPIO 15, but
266 * it cannot handle interrupts on that GPIO line. So we'll
267 * have to poll it with a kernel timer.
268 */
269
270 /* Make sure that the power button GPIO is set up as an input */
271 gpio_line_config(DSMG600_PB_GPIO, IXP4XX_GPIO_IN);
272
273 /* Set the initial value for the power button IRQ handler */
274 power_button_countdown = PBUTTON_HOLDDOWN_COUNT;
275
276 mod_timer(&dsmg600_power_timer, jiffies + msecs_to_jiffies(500));
277 }
278
279 MACHINE_START(DSMG600, "D-Link DSM-G600 RevA")
280 /* Maintainer: www.nslu2-linux.org */
281 .atag_offset = 0x100,
282 .map_io = ixp4xx_map_io,
283 .init_early = ixp4xx_init_early,
284 .init_irq = ixp4xx_init_irq,
285 .timer = &dsmg600_timer,
286 .init_machine = dsmg600_init,
287 #if defined(CONFIG_PCI)
288 .dma_zone_size = SZ_64M,
289 #endif
290 .restart = ixp4xx_restart,
291 MACHINE_END
292