1 /******************************************************************************
2 *
3 * This file is provided under a dual BSD/GPLv2 license. When using or
4 * redistributing this file, you may do so under either license.
5 *
6 * GPL LICENSE SUMMARY
7 *
8 * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of version 2 of the GNU General Public License as
12 * published by the Free Software Foundation.
13 *
14 * This program is distributed in the hope that it will be useful, but
15 * WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
17 * General Public License for more details.
18 *
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110,
22 * USA
23 *
24 * The full GNU General Public License is included in this distribution
25 * in the file called LICENSE.GPL.
26 *
27 * Contact Information:
28 * Intel Linux Wireless <ilw@linux.intel.com>
29 * Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
30 *
31 * BSD LICENSE
32 *
33 * Copyright(c) 2005 - 2011 Intel Corporation. All rights reserved.
34 * All rights reserved.
35 *
36 * Redistribution and use in source and binary forms, with or without
37 * modification, are permitted provided that the following conditions
38 * are met:
39 *
40 * * Redistributions of source code must retain the above copyright
41 * notice, this list of conditions and the following disclaimer.
42 * * Redistributions in binary form must reproduce the above copyright
43 * notice, this list of conditions and the following disclaimer in
44 * the documentation and/or other materials provided with the
45 * distribution.
46 * * Neither the name Intel Corporation nor the names of its
47 * contributors may be used to endorse or promote products derived
48 * from this software without specific prior written permission.
49 *
50 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
51 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
52 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
53 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
54 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
55 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
56 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
57 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
58 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
59 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
60 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
61 *
62 *****************************************************************************/
63 /*
64 * Please use this file (iwl-4965-hw.h) only for hardware-related definitions.
65 * Use iwl-commands.h for uCode API definitions.
66 * Use iwl-dev.h for driver implementation definitions.
67 */
68
69 #ifndef __iwl_4965_hw_h__
70 #define __iwl_4965_hw_h__
71
72 #include "iwl-fh.h"
73
74 /* EEPROM */
75 #define IWL4965_EEPROM_IMG_SIZE 1024
76
77 /*
78 * uCode queue management definitions ...
79 * The first queue used for block-ack aggregation is #7 (4965 only).
80 * All block-ack aggregation queues should map to Tx DMA/FIFO channel 7.
81 */
82 #define IWL49_FIRST_AMPDU_QUEUE 7
83
84 /* Sizes and addresses for instruction and data memory (SRAM) in
85 * 4965's embedded processor. Driver access is via HBUS_TARG_MEM_* regs. */
86 #define IWL49_RTC_INST_LOWER_BOUND (0x000000)
87 #define IWL49_RTC_INST_UPPER_BOUND (0x018000)
88
89 #define IWL49_RTC_DATA_LOWER_BOUND (0x800000)
90 #define IWL49_RTC_DATA_UPPER_BOUND (0x80A000)
91
92 #define IWL49_RTC_INST_SIZE (IWL49_RTC_INST_UPPER_BOUND - \
93 IWL49_RTC_INST_LOWER_BOUND)
94 #define IWL49_RTC_DATA_SIZE (IWL49_RTC_DATA_UPPER_BOUND - \
95 IWL49_RTC_DATA_LOWER_BOUND)
96
97 #define IWL49_MAX_INST_SIZE IWL49_RTC_INST_SIZE
98 #define IWL49_MAX_DATA_SIZE IWL49_RTC_DATA_SIZE
99
100 /* Size of uCode instruction memory in bootstrap state machine */
101 #define IWL49_MAX_BSM_SIZE BSM_SRAM_SIZE
102
iwl4965_hw_valid_rtc_data_addr(u32 addr)103 static inline int iwl4965_hw_valid_rtc_data_addr(u32 addr)
104 {
105 return (addr >= IWL49_RTC_DATA_LOWER_BOUND) &&
106 (addr < IWL49_RTC_DATA_UPPER_BOUND);
107 }
108
109 /********************* START TEMPERATURE *************************************/
110
111 /**
112 * 4965 temperature calculation.
113 *
114 * The driver must calculate the device temperature before calculating
115 * a txpower setting (amplifier gain is temperature dependent). The
116 * calculation uses 4 measurements, 3 of which (R1, R2, R3) are calibration
117 * values used for the life of the driver, and one of which (R4) is the
118 * real-time temperature indicator.
119 *
120 * uCode provides all 4 values to the driver via the "initialize alive"
121 * notification (see struct iwl4965_init_alive_resp). After the runtime uCode
122 * image loads, uCode updates the R4 value via statistics notifications
123 * (see STATISTICS_NOTIFICATION), which occur after each received beacon
124 * when associated, or can be requested via REPLY_STATISTICS_CMD.
125 *
126 * NOTE: uCode provides the R4 value as a 23-bit signed value. Driver
127 * must sign-extend to 32 bits before applying formula below.
128 *
129 * Formula:
130 *
131 * degrees Kelvin = ((97 * 259 * (R4 - R2) / (R3 - R1)) / 100) + 8
132 *
133 * NOTE: The basic formula is 259 * (R4-R2) / (R3-R1). The 97/100 is
134 * an additional correction, which should be centered around 0 degrees
135 * Celsius (273 degrees Kelvin). The 8 (3 percent of 273) compensates for
136 * centering the 97/100 correction around 0 degrees K.
137 *
138 * Add 273 to Kelvin value to find degrees Celsius, for comparing current
139 * temperature with factory-measured temperatures when calculating txpower
140 * settings.
141 */
142 #define TEMPERATURE_CALIB_KELVIN_OFFSET 8
143 #define TEMPERATURE_CALIB_A_VAL 259
144
145 /* Limit range of calculated temperature to be between these Kelvin values */
146 #define IWL_TX_POWER_TEMPERATURE_MIN (263)
147 #define IWL_TX_POWER_TEMPERATURE_MAX (410)
148
149 #define IWL_TX_POWER_TEMPERATURE_OUT_OF_RANGE(t) \
150 (((t) < IWL_TX_POWER_TEMPERATURE_MIN) || \
151 ((t) > IWL_TX_POWER_TEMPERATURE_MAX))
152
153 /********************* END TEMPERATURE ***************************************/
154
155 /********************* START TXPOWER *****************************************/
156
157 /**
158 * 4965 txpower calculations rely on information from three sources:
159 *
160 * 1) EEPROM
161 * 2) "initialize" alive notification
162 * 3) statistics notifications
163 *
164 * EEPROM data consists of:
165 *
166 * 1) Regulatory information (max txpower and channel usage flags) is provided
167 * separately for each channel that can possibly supported by 4965.
168 * 40 MHz wide (.11n HT40) channels are listed separately from 20 MHz
169 * (legacy) channels.
170 *
171 * See struct iwl4965_eeprom_channel for format, and struct iwl4965_eeprom
172 * for locations in EEPROM.
173 *
174 * 2) Factory txpower calibration information is provided separately for
175 * sub-bands of contiguous channels. 2.4GHz has just one sub-band,
176 * but 5 GHz has several sub-bands.
177 *
178 * In addition, per-band (2.4 and 5 Ghz) saturation txpowers are provided.
179 *
180 * See struct iwl4965_eeprom_calib_info (and the tree of structures
181 * contained within it) for format, and struct iwl4965_eeprom for
182 * locations in EEPROM.
183 *
184 * "Initialization alive" notification (see struct iwl4965_init_alive_resp)
185 * consists of:
186 *
187 * 1) Temperature calculation parameters.
188 *
189 * 2) Power supply voltage measurement.
190 *
191 * 3) Tx gain compensation to balance 2 transmitters for MIMO use.
192 *
193 * Statistics notifications deliver:
194 *
195 * 1) Current values for temperature param R4.
196 */
197
198 /**
199 * To calculate a txpower setting for a given desired target txpower, channel,
200 * modulation bit rate, and transmitter chain (4965 has 2 transmitters to
201 * support MIMO and transmit diversity), driver must do the following:
202 *
203 * 1) Compare desired txpower vs. (EEPROM) regulatory limit for this channel.
204 * Do not exceed regulatory limit; reduce target txpower if necessary.
205 *
206 * If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
207 * 2 transmitters will be used simultaneously; driver must reduce the
208 * regulatory limit by 3 dB (half-power) for each transmitter, so the
209 * combined total output of the 2 transmitters is within regulatory limits.
210 *
211 *
212 * 2) Compare target txpower vs. (EEPROM) saturation txpower *reduced by
213 * backoff for this bit rate*. Do not exceed (saturation - backoff[rate]);
214 * reduce target txpower if necessary.
215 *
216 * Backoff values below are in 1/2 dB units (equivalent to steps in
217 * txpower gain tables):
218 *
219 * OFDM 6 - 36 MBit: 10 steps (5 dB)
220 * OFDM 48 MBit: 15 steps (7.5 dB)
221 * OFDM 54 MBit: 17 steps (8.5 dB)
222 * OFDM 60 MBit: 20 steps (10 dB)
223 * CCK all rates: 10 steps (5 dB)
224 *
225 * Backoff values apply to saturation txpower on a per-transmitter basis;
226 * when using MIMO (2 transmitters), each transmitter uses the same
227 * saturation level provided in EEPROM, and the same backoff values;
228 * no reduction (such as with regulatory txpower limits) is required.
229 *
230 * Saturation and Backoff values apply equally to 20 Mhz (legacy) channel
231 * widths and 40 Mhz (.11n HT40) channel widths; there is no separate
232 * factory measurement for ht40 channels.
233 *
234 * The result of this step is the final target txpower. The rest of
235 * the steps figure out the proper settings for the device to achieve
236 * that target txpower.
237 *
238 *
239 * 3) Determine (EEPROM) calibration sub band for the target channel, by
240 * comparing against first and last channels in each sub band
241 * (see struct iwl4965_eeprom_calib_subband_info).
242 *
243 *
244 * 4) Linearly interpolate (EEPROM) factory calibration measurement sets,
245 * referencing the 2 factory-measured (sample) channels within the sub band.
246 *
247 * Interpolation is based on difference between target channel's frequency
248 * and the sample channels' frequencies. Since channel numbers are based
249 * on frequency (5 MHz between each channel number), this is equivalent
250 * to interpolating based on channel number differences.
251 *
252 * Note that the sample channels may or may not be the channels at the
253 * edges of the sub band. The target channel may be "outside" of the
254 * span of the sampled channels.
255 *
256 * Driver may choose the pair (for 2 Tx chains) of measurements (see
257 * struct iwl4965_eeprom_calib_ch_info) for which the actual measured
258 * txpower comes closest to the desired txpower. Usually, though,
259 * the middle set of measurements is closest to the regulatory limits,
260 * and is therefore a good choice for all txpower calculations (this
261 * assumes that high accuracy is needed for maximizing legal txpower,
262 * while lower txpower configurations do not need as much accuracy).
263 *
264 * Driver should interpolate both members of the chosen measurement pair,
265 * i.e. for both Tx chains (radio transmitters), unless the driver knows
266 * that only one of the chains will be used (e.g. only one tx antenna
267 * connected, but this should be unusual). The rate scaling algorithm
268 * switches antennas to find best performance, so both Tx chains will
269 * be used (although only one at a time) even for non-MIMO transmissions.
270 *
271 * Driver should interpolate factory values for temperature, gain table
272 * index, and actual power. The power amplifier detector values are
273 * not used by the driver.
274 *
275 * Sanity check: If the target channel happens to be one of the sample
276 * channels, the results should agree with the sample channel's
277 * measurements!
278 *
279 *
280 * 5) Find difference between desired txpower and (interpolated)
281 * factory-measured txpower. Using (interpolated) factory gain table index
282 * (shown elsewhere) as a starting point, adjust this index lower to
283 * increase txpower, or higher to decrease txpower, until the target
284 * txpower is reached. Each step in the gain table is 1/2 dB.
285 *
286 * For example, if factory measured txpower is 16 dBm, and target txpower
287 * is 13 dBm, add 6 steps to the factory gain index to reduce txpower
288 * by 3 dB.
289 *
290 *
291 * 6) Find difference between current device temperature and (interpolated)
292 * factory-measured temperature for sub-band. Factory values are in
293 * degrees Celsius. To calculate current temperature, see comments for
294 * "4965 temperature calculation".
295 *
296 * If current temperature is higher than factory temperature, driver must
297 * increase gain (lower gain table index), and vice verse.
298 *
299 * Temperature affects gain differently for different channels:
300 *
301 * 2.4 GHz all channels: 3.5 degrees per half-dB step
302 * 5 GHz channels 34-43: 4.5 degrees per half-dB step
303 * 5 GHz channels >= 44: 4.0 degrees per half-dB step
304 *
305 * NOTE: Temperature can increase rapidly when transmitting, especially
306 * with heavy traffic at high txpowers. Driver should update
307 * temperature calculations often under these conditions to
308 * maintain strong txpower in the face of rising temperature.
309 *
310 *
311 * 7) Find difference between current power supply voltage indicator
312 * (from "initialize alive") and factory-measured power supply voltage
313 * indicator (EEPROM).
314 *
315 * If the current voltage is higher (indicator is lower) than factory
316 * voltage, gain should be reduced (gain table index increased) by:
317 *
318 * (eeprom - current) / 7
319 *
320 * If the current voltage is lower (indicator is higher) than factory
321 * voltage, gain should be increased (gain table index decreased) by:
322 *
323 * 2 * (current - eeprom) / 7
324 *
325 * If number of index steps in either direction turns out to be > 2,
326 * something is wrong ... just use 0.
327 *
328 * NOTE: Voltage compensation is independent of band/channel.
329 *
330 * NOTE: "Initialize" uCode measures current voltage, which is assumed
331 * to be constant after this initial measurement. Voltage
332 * compensation for txpower (number of steps in gain table)
333 * may be calculated once and used until the next uCode bootload.
334 *
335 *
336 * 8) If setting up txpowers for MIMO rates (rate indexes 8-15, 24-31),
337 * adjust txpower for each transmitter chain, so txpower is balanced
338 * between the two chains. There are 5 pairs of tx_atten[group][chain]
339 * values in "initialize alive", one pair for each of 5 channel ranges:
340 *
341 * Group 0: 5 GHz channel 34-43
342 * Group 1: 5 GHz channel 44-70
343 * Group 2: 5 GHz channel 71-124
344 * Group 3: 5 GHz channel 125-200
345 * Group 4: 2.4 GHz all channels
346 *
347 * Add the tx_atten[group][chain] value to the index for the target chain.
348 * The values are signed, but are in pairs of 0 and a non-negative number,
349 * so as to reduce gain (if necessary) of the "hotter" channel. This
350 * avoids any need to double-check for regulatory compliance after
351 * this step.
352 *
353 *
354 * 9) If setting up for a CCK rate, lower the gain by adding a CCK compensation
355 * value to the index:
356 *
357 * Hardware rev B: 9 steps (4.5 dB)
358 * Hardware rev C: 5 steps (2.5 dB)
359 *
360 * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
361 * bits [3:2], 1 = B, 2 = C.
362 *
363 * NOTE: This compensation is in addition to any saturation backoff that
364 * might have been applied in an earlier step.
365 *
366 *
367 * 10) Select the gain table, based on band (2.4 vs 5 GHz).
368 *
369 * Limit the adjusted index to stay within the table!
370 *
371 *
372 * 11) Read gain table entries for DSP and radio gain, place into appropriate
373 * location(s) in command (struct iwl4965_txpowertable_cmd).
374 */
375
376 /**
377 * When MIMO is used (2 transmitters operating simultaneously), driver should
378 * limit each transmitter to deliver a max of 3 dB below the regulatory limit
379 * for the device. That is, use half power for each transmitter, so total
380 * txpower is within regulatory limits.
381 *
382 * The value "6" represents number of steps in gain table to reduce power 3 dB.
383 * Each step is 1/2 dB.
384 */
385 #define IWL_TX_POWER_MIMO_REGULATORY_COMPENSATION (6)
386
387 /**
388 * CCK gain compensation.
389 *
390 * When calculating txpowers for CCK, after making sure that the target power
391 * is within regulatory and saturation limits, driver must additionally
392 * back off gain by adding these values to the gain table index.
393 *
394 * Hardware rev for 4965 can be determined by reading CSR_HW_REV_WA_REG,
395 * bits [3:2], 1 = B, 2 = C.
396 */
397 #define IWL_TX_POWER_CCK_COMPENSATION_B_STEP (9)
398 #define IWL_TX_POWER_CCK_COMPENSATION_C_STEP (5)
399
400 /*
401 * 4965 power supply voltage compensation for txpower
402 */
403 #define TX_POWER_IWL_VOLTAGE_CODES_PER_03V (7)
404
405 /**
406 * Gain tables.
407 *
408 * The following tables contain pair of values for setting txpower, i.e.
409 * gain settings for the output of the device's digital signal processor (DSP),
410 * and for the analog gain structure of the transmitter.
411 *
412 * Each entry in the gain tables represents a step of 1/2 dB. Note that these
413 * are *relative* steps, not indications of absolute output power. Output
414 * power varies with temperature, voltage, and channel frequency, and also
415 * requires consideration of average power (to satisfy regulatory constraints),
416 * and peak power (to avoid distortion of the output signal).
417 *
418 * Each entry contains two values:
419 * 1) DSP gain (or sometimes called DSP attenuation). This is a fine-grained
420 * linear value that multiplies the output of the digital signal processor,
421 * before being sent to the analog radio.
422 * 2) Radio gain. This sets the analog gain of the radio Tx path.
423 * It is a coarser setting, and behaves in a logarithmic (dB) fashion.
424 *
425 * EEPROM contains factory calibration data for txpower. This maps actual
426 * measured txpower levels to gain settings in the "well known" tables
427 * below ("well-known" means here that both factory calibration *and* the
428 * driver work with the same table).
429 *
430 * There are separate tables for 2.4 GHz and 5 GHz bands. The 5 GHz table
431 * has an extension (into negative indexes), in case the driver needs to
432 * boost power setting for high device temperatures (higher than would be
433 * present during factory calibration). A 5 Ghz EEPROM index of "40"
434 * corresponds to the 49th entry in the table used by the driver.
435 */
436 #define MIN_TX_GAIN_INDEX (0) /* highest gain, lowest idx, 2.4 */
437 #define MIN_TX_GAIN_INDEX_52GHZ_EXT (-9) /* highest gain, lowest idx, 5 */
438
439 /**
440 * 2.4 GHz gain table
441 *
442 * Index Dsp gain Radio gain
443 * 0 110 0x3f (highest gain)
444 * 1 104 0x3f
445 * 2 98 0x3f
446 * 3 110 0x3e
447 * 4 104 0x3e
448 * 5 98 0x3e
449 * 6 110 0x3d
450 * 7 104 0x3d
451 * 8 98 0x3d
452 * 9 110 0x3c
453 * 10 104 0x3c
454 * 11 98 0x3c
455 * 12 110 0x3b
456 * 13 104 0x3b
457 * 14 98 0x3b
458 * 15 110 0x3a
459 * 16 104 0x3a
460 * 17 98 0x3a
461 * 18 110 0x39
462 * 19 104 0x39
463 * 20 98 0x39
464 * 21 110 0x38
465 * 22 104 0x38
466 * 23 98 0x38
467 * 24 110 0x37
468 * 25 104 0x37
469 * 26 98 0x37
470 * 27 110 0x36
471 * 28 104 0x36
472 * 29 98 0x36
473 * 30 110 0x35
474 * 31 104 0x35
475 * 32 98 0x35
476 * 33 110 0x34
477 * 34 104 0x34
478 * 35 98 0x34
479 * 36 110 0x33
480 * 37 104 0x33
481 * 38 98 0x33
482 * 39 110 0x32
483 * 40 104 0x32
484 * 41 98 0x32
485 * 42 110 0x31
486 * 43 104 0x31
487 * 44 98 0x31
488 * 45 110 0x30
489 * 46 104 0x30
490 * 47 98 0x30
491 * 48 110 0x6
492 * 49 104 0x6
493 * 50 98 0x6
494 * 51 110 0x5
495 * 52 104 0x5
496 * 53 98 0x5
497 * 54 110 0x4
498 * 55 104 0x4
499 * 56 98 0x4
500 * 57 110 0x3
501 * 58 104 0x3
502 * 59 98 0x3
503 * 60 110 0x2
504 * 61 104 0x2
505 * 62 98 0x2
506 * 63 110 0x1
507 * 64 104 0x1
508 * 65 98 0x1
509 * 66 110 0x0
510 * 67 104 0x0
511 * 68 98 0x0
512 * 69 97 0
513 * 70 96 0
514 * 71 95 0
515 * 72 94 0
516 * 73 93 0
517 * 74 92 0
518 * 75 91 0
519 * 76 90 0
520 * 77 89 0
521 * 78 88 0
522 * 79 87 0
523 * 80 86 0
524 * 81 85 0
525 * 82 84 0
526 * 83 83 0
527 * 84 82 0
528 * 85 81 0
529 * 86 80 0
530 * 87 79 0
531 * 88 78 0
532 * 89 77 0
533 * 90 76 0
534 * 91 75 0
535 * 92 74 0
536 * 93 73 0
537 * 94 72 0
538 * 95 71 0
539 * 96 70 0
540 * 97 69 0
541 * 98 68 0
542 */
543
544 /**
545 * 5 GHz gain table
546 *
547 * Index Dsp gain Radio gain
548 * -9 123 0x3F (highest gain)
549 * -8 117 0x3F
550 * -7 110 0x3F
551 * -6 104 0x3F
552 * -5 98 0x3F
553 * -4 110 0x3E
554 * -3 104 0x3E
555 * -2 98 0x3E
556 * -1 110 0x3D
557 * 0 104 0x3D
558 * 1 98 0x3D
559 * 2 110 0x3C
560 * 3 104 0x3C
561 * 4 98 0x3C
562 * 5 110 0x3B
563 * 6 104 0x3B
564 * 7 98 0x3B
565 * 8 110 0x3A
566 * 9 104 0x3A
567 * 10 98 0x3A
568 * 11 110 0x39
569 * 12 104 0x39
570 * 13 98 0x39
571 * 14 110 0x38
572 * 15 104 0x38
573 * 16 98 0x38
574 * 17 110 0x37
575 * 18 104 0x37
576 * 19 98 0x37
577 * 20 110 0x36
578 * 21 104 0x36
579 * 22 98 0x36
580 * 23 110 0x35
581 * 24 104 0x35
582 * 25 98 0x35
583 * 26 110 0x34
584 * 27 104 0x34
585 * 28 98 0x34
586 * 29 110 0x33
587 * 30 104 0x33
588 * 31 98 0x33
589 * 32 110 0x32
590 * 33 104 0x32
591 * 34 98 0x32
592 * 35 110 0x31
593 * 36 104 0x31
594 * 37 98 0x31
595 * 38 110 0x30
596 * 39 104 0x30
597 * 40 98 0x30
598 * 41 110 0x25
599 * 42 104 0x25
600 * 43 98 0x25
601 * 44 110 0x24
602 * 45 104 0x24
603 * 46 98 0x24
604 * 47 110 0x23
605 * 48 104 0x23
606 * 49 98 0x23
607 * 50 110 0x22
608 * 51 104 0x18
609 * 52 98 0x18
610 * 53 110 0x17
611 * 54 104 0x17
612 * 55 98 0x17
613 * 56 110 0x16
614 * 57 104 0x16
615 * 58 98 0x16
616 * 59 110 0x15
617 * 60 104 0x15
618 * 61 98 0x15
619 * 62 110 0x14
620 * 63 104 0x14
621 * 64 98 0x14
622 * 65 110 0x13
623 * 66 104 0x13
624 * 67 98 0x13
625 * 68 110 0x12
626 * 69 104 0x08
627 * 70 98 0x08
628 * 71 110 0x07
629 * 72 104 0x07
630 * 73 98 0x07
631 * 74 110 0x06
632 * 75 104 0x06
633 * 76 98 0x06
634 * 77 110 0x05
635 * 78 104 0x05
636 * 79 98 0x05
637 * 80 110 0x04
638 * 81 104 0x04
639 * 82 98 0x04
640 * 83 110 0x03
641 * 84 104 0x03
642 * 85 98 0x03
643 * 86 110 0x02
644 * 87 104 0x02
645 * 88 98 0x02
646 * 89 110 0x01
647 * 90 104 0x01
648 * 91 98 0x01
649 * 92 110 0x00
650 * 93 104 0x00
651 * 94 98 0x00
652 * 95 93 0x00
653 * 96 88 0x00
654 * 97 83 0x00
655 * 98 78 0x00
656 */
657
658
659 /**
660 * Sanity checks and default values for EEPROM regulatory levels.
661 * If EEPROM values fall outside MIN/MAX range, use default values.
662 *
663 * Regulatory limits refer to the maximum average txpower allowed by
664 * regulatory agencies in the geographies in which the device is meant
665 * to be operated. These limits are SKU-specific (i.e. geography-specific),
666 * and channel-specific; each channel has an individual regulatory limit
667 * listed in the EEPROM.
668 *
669 * Units are in half-dBm (i.e. "34" means 17 dBm).
670 */
671 #define IWL_TX_POWER_DEFAULT_REGULATORY_24 (34)
672 #define IWL_TX_POWER_DEFAULT_REGULATORY_52 (34)
673 #define IWL_TX_POWER_REGULATORY_MIN (0)
674 #define IWL_TX_POWER_REGULATORY_MAX (34)
675
676 /**
677 * Sanity checks and default values for EEPROM saturation levels.
678 * If EEPROM values fall outside MIN/MAX range, use default values.
679 *
680 * Saturation is the highest level that the output power amplifier can produce
681 * without significant clipping distortion. This is a "peak" power level.
682 * Different types of modulation (i.e. various "rates", and OFDM vs. CCK)
683 * require differing amounts of backoff, relative to their average power output,
684 * in order to avoid clipping distortion.
685 *
686 * Driver must make sure that it is violating neither the saturation limit,
687 * nor the regulatory limit, when calculating Tx power settings for various
688 * rates.
689 *
690 * Units are in half-dBm (i.e. "38" means 19 dBm).
691 */
692 #define IWL_TX_POWER_DEFAULT_SATURATION_24 (38)
693 #define IWL_TX_POWER_DEFAULT_SATURATION_52 (38)
694 #define IWL_TX_POWER_SATURATION_MIN (20)
695 #define IWL_TX_POWER_SATURATION_MAX (50)
696
697 /**
698 * Channel groups used for Tx Attenuation calibration (MIMO tx channel balance)
699 * and thermal Txpower calibration.
700 *
701 * When calculating txpower, driver must compensate for current device
702 * temperature; higher temperature requires higher gain. Driver must calculate
703 * current temperature (see "4965 temperature calculation"), then compare vs.
704 * factory calibration temperature in EEPROM; if current temperature is higher
705 * than factory temperature, driver must *increase* gain by proportions shown
706 * in table below. If current temperature is lower than factory, driver must
707 * *decrease* gain.
708 *
709 * Different frequency ranges require different compensation, as shown below.
710 */
711 /* Group 0, 5.2 GHz ch 34-43: 4.5 degrees per 1/2 dB. */
712 #define CALIB_IWL_TX_ATTEN_GR1_FCH 34
713 #define CALIB_IWL_TX_ATTEN_GR1_LCH 43
714
715 /* Group 1, 5.3 GHz ch 44-70: 4.0 degrees per 1/2 dB. */
716 #define CALIB_IWL_TX_ATTEN_GR2_FCH 44
717 #define CALIB_IWL_TX_ATTEN_GR2_LCH 70
718
719 /* Group 2, 5.5 GHz ch 71-124: 4.0 degrees per 1/2 dB. */
720 #define CALIB_IWL_TX_ATTEN_GR3_FCH 71
721 #define CALIB_IWL_TX_ATTEN_GR3_LCH 124
722
723 /* Group 3, 5.7 GHz ch 125-200: 4.0 degrees per 1/2 dB. */
724 #define CALIB_IWL_TX_ATTEN_GR4_FCH 125
725 #define CALIB_IWL_TX_ATTEN_GR4_LCH 200
726
727 /* Group 4, 2.4 GHz all channels: 3.5 degrees per 1/2 dB. */
728 #define CALIB_IWL_TX_ATTEN_GR5_FCH 1
729 #define CALIB_IWL_TX_ATTEN_GR5_LCH 20
730
731 enum {
732 CALIB_CH_GROUP_1 = 0,
733 CALIB_CH_GROUP_2 = 1,
734 CALIB_CH_GROUP_3 = 2,
735 CALIB_CH_GROUP_4 = 3,
736 CALIB_CH_GROUP_5 = 4,
737 CALIB_CH_GROUP_MAX
738 };
739
740 /********************* END TXPOWER *****************************************/
741
742
743 /**
744 * Tx/Rx Queues
745 *
746 * Most communication between driver and 4965 is via queues of data buffers.
747 * For example, all commands that the driver issues to device's embedded
748 * controller (uCode) are via the command queue (one of the Tx queues). All
749 * uCode command responses/replies/notifications, including Rx frames, are
750 * conveyed from uCode to driver via the Rx queue.
751 *
752 * Most support for these queues, including handshake support, resides in
753 * structures in host DRAM, shared between the driver and the device. When
754 * allocating this memory, the driver must make sure that data written by
755 * the host CPU updates DRAM immediately (and does not get "stuck" in CPU's
756 * cache memory), so DRAM and cache are consistent, and the device can
757 * immediately see changes made by the driver.
758 *
759 * 4965 supports up to 16 DRAM-based Tx queues, and services these queues via
760 * up to 7 DMA channels (FIFOs). Each Tx queue is supported by a circular array
761 * in DRAM containing 256 Transmit Frame Descriptors (TFDs).
762 */
763 #define IWL49_NUM_FIFOS 7
764 #define IWL49_CMD_FIFO_NUM 4
765 #define IWL49_NUM_QUEUES 16
766 #define IWL49_NUM_AMPDU_QUEUES 8
767
768
769 /**
770 * struct iwl4965_schedq_bc_tbl
771 *
772 * Byte Count table
773 *
774 * Each Tx queue uses a byte-count table containing 320 entries:
775 * one 16-bit entry for each of 256 TFDs, plus an additional 64 entries that
776 * duplicate the first 64 entries (to avoid wrap-around within a Tx window;
777 * max Tx window is 64 TFDs).
778 *
779 * When driver sets up a new TFD, it must also enter the total byte count
780 * of the frame to be transmitted into the corresponding entry in the byte
781 * count table for the chosen Tx queue. If the TFD index is 0-63, the driver
782 * must duplicate the byte count entry in corresponding index 256-319.
783 *
784 * padding puts each byte count table on a 1024-byte boundary;
785 * 4965 assumes tables are separated by 1024 bytes.
786 */
787 struct iwl4965_scd_bc_tbl {
788 __le16 tfd_offset[TFD_QUEUE_BC_SIZE];
789 u8 pad[1024 - (TFD_QUEUE_BC_SIZE) * sizeof(__le16)];
790 } __packed;
791
792
793 #define IWL4965_RTC_INST_LOWER_BOUND (0x000000)
794
795 /* RSSI to dBm */
796 #define IWL4965_RSSI_OFFSET 44
797
798 /* PCI registers */
799 #define PCI_CFG_RETRY_TIMEOUT 0x041
800
801 /* PCI register values */
802 #define PCI_CFG_LINK_CTRL_VAL_L0S_EN 0x01
803 #define PCI_CFG_LINK_CTRL_VAL_L1_EN 0x02
804
805 #define IWL4965_DEFAULT_TX_RETRY 15
806
807 /* EEPROM */
808 #define IWL4965_FIRST_AMPDU_QUEUE 10
809
810
811 #endif /* !__iwl_4965_hw_h__ */
812