1 This file contains notes for users of PSS sound cards who wish to use the 2newly added features of the newest version of this driver. 3 4 The major enhancements present in this new revision of this driver is the 5addition of two new module parameters that allow you to take full advantage of 6all the features present on your PSS sound card. These features include the 7ability to enable both the builtin CDROM and joystick ports. 8 9pss_enable_joystick 10 11 This parameter is basically a flag. A 0 will leave the joystick port 12disabled, while a non-zero value would enable the joystick port. The default 13setting is pss_enable_joystick=0 as this keeps this driver fully compatable 14with systems that were using previous versions of this driver. If you wish to 15enable the joystick port you will have to add pss_enable_joystick=1 as an 16argument to the driver. To actually use the joystick port you will then have 17to load the joystick driver itself. Just remember to load the joystick driver 18AFTER the pss sound driver. 19 20pss_cdrom_port 21 22 This parameter takes a port address as its parameter. Any available port 23address can be specified to enable the CDROM port, except for 0x0 and -1 as 24these values would leave the port disabled. Like the joystick port, the cdrom 25port will require that an appropiate CDROM driver be loaded before you can make 26use of the newly enabled CDROM port. Like the joystick port option above, 27remember to load the CDROM driver AFTER the pss sound driver. While it may 28differ on some PSS sound cards, all the PSS sound cards that I have seen have a 29builtin Wearnes CDROM port. If this is the case with your PSS sound card you 30should load aztcd with the appropiate port option that matches the port you 31assigned to the CDROM port when you loaded your pss sound driver. (ex. 32modprobe pss pss_cdrom_port=0x340 && modprobe aztcd aztcd=0x340) The default 33setting of this parameter leaves the CDROM port disabled to maintain full 34compatability with systems using previous versions of this driver. 35 36 Other options have also been added for the added convenience and utility 37of the user. These options are only available if this driver is loaded as a 38module. 39 40pss_no_sound 41 42 This module parameter is a flag that can be used to tell the driver to 43just configure non-sound components. 0 configures all components, a non-0 44value will only attept to configure the CDROM and joystick ports. This 45parameter can be used by a user who only wished to use the builtin joystick 46and/or CDROM port(s) of his PSS sound card. If this driver is loaded with this 47parameter and with the paramter below set to true then a user can safely unload 48this driver with the following command "rmmod pss && rmmod ad1848 && rmmod 49mpu401 && rmmod sound && rmmod soundcore" and retain the full functionality of 50his CDROM and/or joystick port(s) while gaining back the memory previously used 51by the sound drivers. This default setting of this parameter is 0 to retain 52full behavioral compatability with previous versions of this driver. 53 54pss_keep_settings 55 56 This parameter can be used to specify whether you want the driver to reset 57all emulations whenever its unloaded. This can be useful for those who are 58sharing resources (io ports, IRQ's, DMA's) between different ISA cards. This 59flag can also be useful in that future versions of this driver may reset all 60emulations by default on the driver's unloading (as it probably should), so 61specifying it now will ensure that all future versions of this driver will 62continue to work as expected. The default value of this parameter is 1 to 63retain full behavioral compatability with previous versions of this driver. 64 65pss_firmware 66 67 This parameter can be used to specify the file containing the firmware 68code so that a user could tell the driver where that file is located instead 69of having to put it in a predefined location with a predefined name. The 70default setting of this parameter is "/etc/sound/pss_synth" as this was the 71path and filename the hardcoded value in the previous versions of this driver. 72 73Examples: 74 75# Normal PSS sound card system, loading of drivers. 76# Should be specified in an rc file (ex. Slackware uses /etc/rc.d/rc.modules). 77 78/sbin/modprobe pss pss_io=0x220 mpu_io=0x338 mpu_irq=9 mss_io=0x530 mss_irq=10 mss_dma=1 pss_cdrom_port=0x340 pss_enable_joystick=1 79/sbin/modprobe aztcd aztcd=0x340 80/sbin/modprobe joystick 81 82# System using the PSS sound card just for its CDROM and joystick ports. 83# Should be specified in an rc file (ex. Slackware uses /etc/rc.d/rc.modules). 84 85/sbin/modprobe pss pss_io=0x220 pss_cdrom_port=0x340 pss_enable_joystick=1 pss_no_sound=1 86/sbin/rmmod pss && /sbin/rmmod ad1848 && /sbin/rmmod mpu401 && /sbin/rmmod sound && /sbin/rmmod soundcore # This line not needed, but saves memory. 87/sbin/modprobe aztcd aztcd=0x340 88/sbin/modprobe joystick 89