| /linux-6.1.9/arch/arm/mach-pxa/ |
| D | colibri-pcmcia.c | 35 READY = 1, enumerator
61 skt->socket.pci_irq = gpio_to_irq(colibri_pcmcia_gpios[READY].gpio); in colibri_pcmcia_hw_init()
80 state->ready = !!gpio_get_value(colibri_pcmcia_gpios[READY].gpio); in colibri_pcmcia_socket_state()
131 colibri_pcmcia_gpios[READY].gpio = COLIBRI270_READY_GPIO; in colibri_pcmcia_init()
139 colibri_pcmcia_gpios[READY].gpio = COLIBRI320_READY_GPIO; in colibri_pcmcia_init()
|
| /linux-6.1.9/Documentation/devicetree/bindings/iio/light/ |
| D | ams,as73211.yaml | 28 Interrupt specifier for the READY interrupt generated by the device.
51 interrupts = <19 IRQ_TYPE_EDGE_RISING>; /* READY */
|
| /linux-6.1.9/Documentation/devicetree/bindings/net/ |
| D | intel,ixp4xx-ethernet.yaml | 42 - description: phandle to the TX READY queue node
43 - description: TX READY queue instance to use
44 description: phandle to the TX READY queue on the NPE
|
| /linux-6.1.9/drivers/usb/image/ |
| D | mdc800.c | 119 NOT_CONNECTED, READY, WORKING, DOWNLOAD enumerator
372 mdc800->state=READY; in mdc800_usb_write_notify()
394 mdc800->state=READY; in mdc800_usb_download_notify()
527 mdc800->state=READY; in mdc800_usb_probe()
786 if (mdc800->state != READY) in mdc800_device_write()
878 mdc800->state=READY; in mdc800_device_write()
931 mdc800->state=READY; in mdc800_device_write()
|
| /linux-6.1.9/Documentation/devicetree/bindings/crypto/ |
| D | intel,ixp4xx-crypto.yaml | 45 - description: phandle to the TX READY queue on the NPE
47 description: phandle to the TX READY queue on the NPE, the cell describing
|
| /linux-6.1.9/Documentation/devicetree/bindings/mfd/ |
| D | rohm,bd71837-pmic.yaml | 45 # are called as SNVS and READY. At READY state all the PMIC power outputs go
51 # switched power state to SNVS. If reset is done via READY state the power
53 # target state is set to READY by default. If SNVS state is used the boot
|
| D | rohm,bd71847-pmic.yaml | 45 # states. States are called as SNVS and READY. At READY state all the PMIC
51 # reset has switched power state to SNVS. If reset is done via READY state the
53 # target state is set to READY by default. If SNVS state is used the boot
|
| /linux-6.1.9/drivers/net/ethernet/qualcomm/emac/ |
| D | emac-sgmii-fsm9900.c | 88 #define READY BIT(5) macro
224 if (readl(phy->base + EMAC_QSERDES_COM_RESET_SM) & READY) in emac_sgmii_init_fsm9900()
|
| /linux-6.1.9/drivers/infiniband/hw/qib/ |
| D | qib_diag.c | 64 enum diag_state { UNUSED = 0, OPENED, INIT, READY }; enumerator
776 else if (dc->state < READY && (*off || count != 8)) in qib_diag_read()
850 else if (dc->state < READY && in qib_diag_write()
902 dc->state = READY; /* all read/write OK now */ in qib_diag_write()
|
| /linux-6.1.9/arch/m68k/fpsp040/ |
| D | slogn.S | 364 movel FFRAC(%a6),%d0 | ...READY TO GET ADDRESS OF 1/F
375 fmovemx %fp2-%fp2/%fp3,-(%sp) | ...SAVE FP2 WHILE FP0 IS NOT READY
382 fmulx LOGOF2,%fp1 | ...GET K*LOG2 WHILE FP0 IS NOT READY
|
| D | ssin.S | 208 |--FP1 IS NOW READY
300 |--FP0 IS NOW READY
461 |--FP2 IS READY
470 |--FP2 IS READY
563 |--FP1 IS NOW READY
|
| D | satan.S | 316 |--U IN FP0, WE ARE NOW READY TO COMPUTE ATAN(U) AS
|
| D | stan.S | 195 |--FP1 IS NOW READY
|
| /linux-6.1.9/drivers/misc/mei/ |
| D | debugfs.c | 96 MEI_PXP_MODE(READY); in mei_dev_pxp_mode_str()
|
| /linux-6.1.9/Documentation/driver-api/ |
| D | hsi.rst | 16 signals and an additional READY signal for flow control. An additional WAKE
|
| /linux-6.1.9/Documentation/devicetree/bindings/bus/ |
| D | nvidia,tegra20-gmi.txt | 69 - nvidia,snor-wait-width: Number of cycles before READY is asserted.
|
| /linux-6.1.9/Documentation/mhi/ |
| D | mhi.rst | 197 * Waits until the device enters READY state.
|
| /linux-6.1.9/drivers/net/phy/ |
| D | phy.c | 49 PHY_STATE_STR(READY) in phy_state_to_str()
|
| /linux-6.1.9/Documentation/hid/ |
| D | intel-ish-hid.rst | 285 | | |-----HOST READY--------------->|
|
| /linux-6.1.9/sound/core/ |
| D | pcm.c | 234 #define READY(v) [SNDRV_PCM_READY_##v] = #v macro
|
| /linux-6.1.9/Documentation/scsi/ |
| D | libsas.rst | 398 you e.g., change the meaning of the READY LED MEANING
|
| D | ChangeLog.megaraid_sas | 557 …al state before firing INIT, now we send RESET Flag to FW instead of just READY. This is used to d…
|
| D | sym53c8xx_2.rst | 885 first TEST UNIT READY command received for this device.
|
| D | ncr53c8xx.rst | 1181 first TEST UNIT READY command received for this device.
|
| /linux-6.1.9/drivers/net/ethernet/marvell/octeontx2/af/ |
| D | mbox.h | 127 M(READY, 0x001, ready, msg_req, ready_msg_rsp) \
|