Searched refs:VSYNC (Results 1 – 25 of 40) sorted by relevance
12
| /linux-5.19.10/drivers/gpu/drm/nouveau/dispnv50/ |
| D | dac507d.c | 38 sync |= NVVAL(NV507D, DAC_SET_POLARITY, VSYNC, asyh->or.nvsync); in dac507d_ctrl()
|
| /linux-5.19.10/Documentation/devicetree/bindings/media/ |
| D | renesas,vin.yaml | 87 If both HSYNC and VSYNC polarities are not specified, embedded
93 If both HSYNC and VSYNC polarities are not specified, embedded
136 If both HSYNC and VSYNC polarities are not specified, embedded
142 If both HSYNC and VSYNC polarities are not specified, embedded
|
| D | video-interfaces.yaml | 124 Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. Note,
125 that if HSYNC and VSYNC polarities are not specified, embedded
132 Similar to HSYNC and VSYNC, specifies data line polarity.
138 Similar to HSYNC and VSYNC, specifies the data enable signal polarity.
|
| /linux-5.19.10/Documentation/devicetree/bindings/media/i2c/ |
| D | tvp514x.txt | 19 - vsync-active: VSYNC Polarity configuration for endpoint.
|
| D | tvp7002.txt | 13 - vsync-active: VSYNC Polarity configuration for the bus. Default value when
|
| D | ov7670.txt | 14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | st,st-mipid02.txt | 47 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | tvp5150.txt | 45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
|
| /linux-5.19.10/drivers/video/fbdev/i810/ |
| D | i810_regs.h | 153 #define VSYNC 0x60014 macro
|
| /linux-5.19.10/Documentation/fb/ |
| D | pxafb.rst | 45 vsynclen:VSYNC == LCCR2_VSW + 1
65 hsync:HSYNC, vsync:VSYNC
|
| D | matroxfb.rst | 265 upper:X top boundary: lines between end of VSYNC pulse and start of first
267 lower:X bottom boundary: lines between end of picture and start of VSYNC
269 vslen:X length of VSYNC pulse, in lines. Default is derived from `vesa`
279 sync:X sync. pulse - bit 0 inverts HSYNC polarity, bit 1 VSYNC polarity.
|
| /linux-5.19.10/Documentation/devicetree/bindings/display/samsung/ |
| D | samsung,exynos7-decon.yaml | 73 - description: VSYNC
|
| D | samsung,fimd.yaml | 100 - description: VSYNC
|
| /linux-5.19.10/Documentation/devicetree/bindings/display/rockchip/ |
| D | rockchip-vop.yaml | 49 frame start (VSYNC), line flag and other status interrupts.
|
| D | rockchip-vop2.yaml | 42 frame start (VSYNC), line flag and other status interrupts.
|
| /linux-5.19.10/include/video/ |
| D | sstfb.h | 162 #define VSYNC 0x0224 macro
|
| /linux-5.19.10/Documentation/devicetree/bindings/display/exynos/ |
| D | exynos_dp.txt | 38 VSYNC polarity configuration.
|
| /linux-5.19.10/arch/arm/boot/dts/ |
| D | am437x-sbc-t43.dts | 59 AM4372_IOPAD(0x8e0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* DSS VSYNC */
|
| D | imx53-qsb-common.dtsi | 297 /* VGA_HSYNC, VSYNC with max drive strength */
|
| D | imx6ul-tx6ul-mainboard.dts | 206 MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
|
| D | imx6ul-tx6ul.dtsi | 600 MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
633 MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x10 /* VSYNC */
|
| /linux-5.19.10/drivers/gpu/drm/bridge/ |
| D | chipone-icn6211.c | 44 #define VSYNC 0x28 macro
391 chipone_writeb(icn, VSYNC, mode->vsync_end - mode->vsync_start); in chipone_atomic_enable()
|
| /linux-5.19.10/Documentation/userspace-api/media/drivers/ |
| D | imx-uapi.rst | 94 Input capture requires hardware support. A VSYNC signal must be routed
|
| /linux-5.19.10/drivers/gpu/drm/i915/ |
| D | intel_gvt_mmio_table.c | 221 MMIO_D(VSYNC(TRANSCODER_A)); in iterate_generic_mmio()
230 MMIO_D(VSYNC(TRANSCODER_B)); in iterate_generic_mmio()
239 MMIO_D(VSYNC(TRANSCODER_C)); in iterate_generic_mmio()
248 MMIO_D(VSYNC(TRANSCODER_EDP)); in iterate_generic_mmio()
|
| /linux-5.19.10/drivers/video/fbdev/omap2/omapfb/dss/ |
| D | dispc-compat.c | 81 PIS(VSYNC); in dispc_dump_irqs()
|
12