Searched refs:steps (Results 1 – 25 of 53) sorted by relevance
123
| /linux-2.4.37.9/Documentation/sound/ |
| D | vwsnd | 154 which range from -82.5 dB to +12.0 dB in 1.5 dB steps. Those 64
162 -34.5 dB to +12.0 dB in 1.5 dB steps. Those 32 levels are mapped onto
170 1.5 dB steps. Those 32 levels are mapped onto 100 levels at the
178 -34.5 dB to +12.0 dB in 1.5 dB steps. Those 32 levels are mapped onto
186 steps. Those 16 levels are mapped onto 100 levels at the ioctl, see
209 steps. Each control has 1.5 dB of gain per step. Each control is
226 So each OSS gain control has 101 steps. But the hardware has 16, 32,
227 or 64 steps. The hardware steps are spread across the 101 OSS steps
|
| D | AudioExcelDSP16 | 75 Follow these steps:
|
| D | mwave | 15 The steps, then:
|
| /linux-2.4.37.9/drivers/video/ |
| D | cgthreefb.c | 96 int steps; in cg3_loadcmap() local
101 steps = D4M3(index+count-1) - D4M3(index)+3; in cg3_loadcmap()
105 while (steps--) { in cg3_loadcmap()
|
| /linux-2.4.37.9/drivers/i2c/ |
| D | i2c-keywest.c | 439 unsigned long steps, *psteps, *prate; in create_iface() local
445 steps = psteps ? (*psteps) : 0x10; in create_iface()
448 for (bsteps = 0; (steps & 0x01) == 0; bsteps++) in create_iface()
449 steps >>= 1; in create_iface()
|
| /linux-2.4.37.9/arch/cris/boot/compressed/ |
| D | README | 4 This can be slightly confusing because it's a process with many steps.
|
| /linux-2.4.37.9/Documentation/ |
| D | LVM-HOWTO | 63 Installation steps see INSTALL and insmod(1)/modprobe(1), kmod/kerneld(8)
68 Configuration steps for getting the above scenario:
|
| D | wolfson-touchscreen.txt | 101 0 to Vmid in 15 steps, 0 = use zero power comparator with Vmid threshold
|
| D | moxa-smartio | 253 kernel. If 'lilo' is not installed, please follow the following steps.
307 2 free major numbers for this driver. There are 3 steps to change
|
| D | parport.txt | 229 If you are having problems printing, please go through these steps to
|
| /linux-2.4.37.9/Documentation/networking/ |
| D | dmfe.txt | 28 B. The following steps teach you how to activate a DM9102 board:
|
| D | iphase.txt | 39 To install the ATM adapters in the system, follow the steps below.
|
| D | sk98lin.txt | 55 The following steps describe the actions that are required to install
56 the driver and to start it manually. These steps should be carried
114 For each adapter, repeat steps 3 and 4 below.
|
| D | dl2k.txt | 173 utility with a graphical user interface is provided to perform steps 2
|
| D | decnet.txt | 108 - If the previous two steps are satisfied, and the Ethernet card is up,
|
| /linux-2.4.37.9/Documentation/s390/ |
| D | 3270.txt | 61 In brief, these are the steps:
73 Here are the installation steps in detail:
128 should follow these steps:
134 Here are the testing steps in detail:
|
| /linux-2.4.37.9/Documentation/isdn/ |
| D | README.sc | 183 A) 10 steps to the establishment of a basic HDLC connection
218 use the same procedure as in the HDLC connection from steps i) to
220 "encap" to syncppp. With this done, the rest of the steps, iv) to x)
|
| D | README.icn | 18 2. A memory window with 16KB-256KB size, which can be setup in 16k steps
|
| /linux-2.4.37.9/Documentation/usb/ |
| D | rio.txt | 105 hardware (determined from the steps above), 'USB Diamond Rio500 support', and
|
| /linux-2.4.37.9/arch/sparc/lib/ |
| D | udiv.S | 114 ! do single-bit divide steps
|
| D | urem.S | 112 ! do single-bit divide steps
|
| D | rem.S | 129 ! do single-bit divide steps
|
| D | sdiv.S | 128 ! do single-bit divide steps
|
| /linux-2.4.37.9/Documentation/mips/ |
| D | time.README | 103 c) The following sub steps assume your CPU has counter register.
|
| /linux-2.4.37.9/Documentation/m68k/ |
| D | README.buddha | 26 Setting the base address should be done in two steps, just
|
123