| /linux-2.4.37.9/Documentation/video4linux/bttv/ |
| D | Insmod-options | 22 50 useless IRQs/sec. default is 0 (off).
24 default is 1 (on).
26 looking at the hardware). default is 1.
28 default is 0 (off).
30 default is 0 (off).
32 default is 4.
33 gbufsize= size of capture buffers. default and
39 by default on this hardware to avoid crashes.
42 no TV signal, on by default. You might try
46 chroma_agc=0/1 AGC of chroma signal, off by default.
[all …]
|
| /linux-2.4.37.9/Documentation/filesystems/ |
| D | udf.txt | 16 gid= Set the default group.
17 umask= Set the default umask.
18 uid= Set the default user.
22 adinicb Embed data in the inode (default)
25 longad Use long ad's (default)
35 session= Set the CDROM session (default= last session)
36 anchor= Override standard anchor location. (default= 256)
|
| D | xfs.txt | 23 Sets the preferred buffered I/O size (default size is 64K).
35 and is still the default for now. Using the noikeep option,
41 The default value is 8 buffers for filesystems with a
55 The default value for machines with more than 32MB of memory
56 is 32768, machines with less memory use 16384 by default.
161 Controls whether symlinks are created with mode 0777 (default)
|
| /linux-2.4.37.9/Documentation/networking/ |
| D | policy-routing.txt | 28 by default.
31 normal default routes are put there, if ip_fib_model==2
59 0 default default 00 * 255
60 254 default default 00 * 254
61 255 default default 00 * 253
121 iproute add default reject class 250
122 iproute add default reject class 249
146 I set it to FALSE by default.
|
| D | ip-sysctl.txt | 4 0 - disabled (default)
10 parameters to their default state (RFC1122 for hosts, RFC1812
14 default 64
18 default FALSE
93 Minimal RFC value is 3, it is default, which corresponds
126 if network conditions require more than default value.
146 if network conditions require more than default value,
221 tcp_wmem - vector of 3 INTEGERs: min, default, max
226 default: Amount of memory allowed for send buffers for TCP socket
227 by default. This value overrides net.core.wmem_default used
[all …]
|
| D | ray_cs.txt | 77 default = 256
79 country integer 1 = USA (default)
90 default value = "ADHOC_ESSID"
93 legal values = 16,32,64,128(default),256
101 net_type integer 0 (default) = adhoc network,
118 sniffer integer 0 = not sniffer (default)
|
| D | ip_dynaddr.txt | 19 [*] At boot, by default no address rewriting is attempted.
24 To disable (default)
|
| D | 3c359.txt | 25 ringspeed: Has one of three settings 0 (default), 4 or 16. 0 will
27 this will be the default option for most people. 4 or 16 allow you to
37 default to 4096 if no value is entered. You may increase performance of the
|
| /linux-2.4.37.9/Documentation/s390/ |
| D | c7000.txt | 11 (first string). The default value is "UTS".
15 (second string). The default value is "C7011".
19 (third string). The default value is "TCPIP".
23 (fourth string). The default value is "TCPIP".
27 The default value is 0.
32 is not done. The default value is 0.
55 The route command is used to specify the router as the default route:
57 route add default gw 129.212.61.200
|
| /linux-2.4.37.9/Documentation/sysctl/ |
| D | vm.txt | 71 of more frequent I/O operations. The default
81 default value is 500 dirty buffers, the
93 default value is 5 seconds, the minimum is 0
99 The default value is 30 seconds, the minimum
106 bdflush forces buffers to disk. The default
112 is dirty which will stop bdflush. The default
118 So the default is: 30 500 0 0 500 3000 60 20 0 for 100 HZ.
130 It is advisable to shut down syslog first! The default is 0.
169 The default value is: 512 32 8.
182 The default value is 0.
[all …]
|
| /linux-2.4.37.9/Documentation/sound/ |
| D | README.awe | 107 As default, AWE driver probes these values automatically.
114 - AWE_DEFAULT_BASE_ADDR (default: not defined)
118 - AWE_DEFAULT_MEM_SIZE (default: not defined)
134 - AWE_ALWAYS_INIT_FM (default: not defined)
140 - AWE_DEBUG_ON (default: defined)
143 - AWE_HAS_GUS_COMPATIBILITY (default: defined)
148 - CONFIG_AWE32_MIDIEMU (default: defined)
154 - CONFIG_AWE32_MIXER (default: not defined)
158 - AWE_USE_NEW_VOLUME_CALC (default: defined)
163 - AWE_CHECK_VTARGET (default: defined)
[all …]
|
| D | PSS-updates | 12 disabled, while a non-zero value would enable the joystick port. The default
32 modprobe pss pss_cdrom_port=0x340 && modprobe aztcd aztcd=0x340) The default
51 by the sound drivers. This default setting of this parameter is 0 to retain
60 emulations by default on the driver's unloading (as it probably should), so
62 continue to work as expected. The default value of this parameter is 1 to
70 default setting of this parameter is "/etc/sound/pss_synth" as this was the
|
| D | ChangeLog.awe | 35 - Change default chorus & reverb modes
38 - Use indirect voice allocation mode; used as default mode
41 - Set default preset/bank/drumset as variable
46 - Add channel priority mode macro, and disable it as default
128 - Fix bugs on searching the default drumset/preset.
129 - Fix usslite patch to modify the default Config.in.
|
| /linux-2.4.37.9/drivers/scsi/ |
| D | README.aha152x | 20 IRQ interrupt level (9-12; default 11)
21 SCSI_ID scsi id of controller (0-7; default 7)
22 RECONNECT allow targets to disconnect from the bus (0/1; default 1 [on])
23 PARITY enable parity checking (0/1; default 1 [on])
24 SYNCHRONOUS enable synchronous transfers (0/1; default 1 [on])
25 DELAY: bus reset delay (default 100)
26 EXT_TRANS: enable extended translation (0/1: default 0 [off])
133 This is considered to be the default translation.
150 - for disks<1GB: use default translation (C/32/64)
159 kernel or module parameter, otherwise take default translation and
|
| D | README.ncr53c8xx | 54 10.2.21 Suggest a default SCSI id for hosts
260 is currently set to 8 by default. This value is suitable for most SCSI
296 driver notifies by default this problem to user by indicating the actual
320 feature is disabled by default and requires a compilation configuration
474 must not be greater than SCSI_NCR_MAX_TAGS (default: 8)
483 default: use default tag type,
536 The driver default verbose level is 1. This command allows to change
565 CONFIG_SCSI_NCR53C8XX_PROFILE_SUPPORT (default answer: n)
570 CONFIG_SCSI_NCR53C8XX_IOMAPPED (default answer: n)
577 CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS (default answer: 8)
[all …]
|
| /linux-2.4.37.9/scripts/ |
| D | Menuconfig | 328 default=$3
348 : ${current:=$default}
432 '$default' " >MCmenu
730 "default=$1\n"\
832 $1 "$default" 2> MCerror #Create the lxdialog menu & functions
879 default="${selection%%\ *}"
1204 default="$3"
1222 : ${current:=$default}
|
| /linux-2.4.37.9/Documentation/x86_64/ |
| D | boot-options.txt | 25 kernels already turn it off by default if the
45 default because it has some cosmetic problems.
86 kbd Use the keyboard controller. cold reset (default)
99 noforce (default) Don't enable by default for heap/stack/data,
104 Control the no exec default for 32bit processes.
109 off (default) Heap,stack,data is executable
112 compat (default) Imply PROT_EXEC for PROT_READ
|
| /linux-2.4.37.9/Documentation/fb/ |
| D | matroxfb.txt | 121 `off'). It is default.
123 accel - use acceleration engine. It is default.
127 It is default.
132 pciretry - enable PCI retries. It is default, except for intel's 82437.
133 novga - disables VGA I/O ports. It is default if BIOS did not enable device.
136 vga - preserve state of VGA I/O ports. It is default. Driver does not
139 nobios - disables BIOS ROM. It is default if BIOS did not enable BIOS itself.
142 bios - preserve state of BIOS ROM. It is default. Driver does not enable
147 are still initialized. It is default.
174 much. It is default. You must have MTRR support enabled in kernel
[all …]
|
| D | pvr2fb.txt | 29 font:X - default font to use. All fonts are supported, including the
32 mode:X - default video mode. The following video modes are supported:
43 dropouts). MTRR is enabled by default on systems that have it
|
| D | modedb.txt | 3 modedb default video mode support
42 fails, the default mode is tried. If that fails, it walks over all modes.
47 where <driver> is a name from the table below. Valid default modes can be
|
| /linux-2.4.37.9/Documentation/ia64/ |
| D | IRQ-redir.txt | 25 Set the default route for IRQ number 41 to CPU 6 in lowest priority
38 Initialization and default behavior:
41 IO-SAPIC interrupts are initialized with CPU#0 as their default target
50 search begins at the default CPU. Therefore most of the interrupts
|
| /linux-2.4.37.9/drivers/scsi/aic7xxx/ |
| D | README.aic79xx | 112 - Correct default precompensation value for RevA hardware.
236 This option sets the default tag depth which
246 the default tag depth.
252 leaves target 6 at the default
254 All other targets retain the default depth.
259 All other targets retain the default depth.
270 they should retain the default read streaming setting.
275 All other targets retain the default read
283 All other targets retain the default read
292 they should retain the default read streaming setting.
[all …]
|
| /linux-2.4.37.9/Documentation/usb/ |
| D | philips.txt | 16 When you load the module you can set some default settings for the
33 only introduces lag, so choose carefully. The default is 3, which is
39 The default is 2, which is adequate for most applications (double
60 default this option is disabled.
74 introduce some unwanted artefacts. The default is 2, medium compression.
94 By default the camera's LED is on solid while in use, and turned off
183 The default value for trace is 35 (0x23).
195 default of defaults is QCIF size at 10 fps, BGR order.
|
| /linux-2.4.37.9/Documentation/ |
| D | floppy.txt | 30 restore the default behavior.
45 Sets the bit mask to allow only units 0 and 1. (default)
58 (default)
95 (default)
103 Enables the FIFO. (default)
124 the default (0xa) is reasonable.
146 (default)
187 It's been recommended that take about 1/4 of the default speed
|
| /linux-2.4.37.9/Documentation/isdn/ |
| D | README.audio | 55 (default 0 , deactivated)
57 of 0.1 second. (default 70)
65 (default 0 , I4L soft-decode)
68 Not for I4L soft decode (default 8, 40ms)
|