1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Atmel MultiMedia Card Interface driver
4 *
5 * Copyright (C) 2004-2008 Atmel Corporation
6 */
7 #include <linux/blkdev.h>
8 #include <linux/clk.h>
9 #include <linux/debugfs.h>
10 #include <linux/device.h>
11 #include <linux/dmaengine.h>
12 #include <linux/dma-mapping.h>
13 #include <linux/err.h>
14 #include <linux/gpio.h>
15 #include <linux/init.h>
16 #include <linux/interrupt.h>
17 #include <linux/io.h>
18 #include <linux/ioport.h>
19 #include <linux/module.h>
20 #include <linux/of.h>
21 #include <linux/of_device.h>
22 #include <linux/of_gpio.h>
23 #include <linux/platform_device.h>
24 #include <linux/scatterlist.h>
25 #include <linux/seq_file.h>
26 #include <linux/slab.h>
27 #include <linux/stat.h>
28 #include <linux/types.h>
29
30 #include <linux/mmc/host.h>
31 #include <linux/mmc/sdio.h>
32
33 #include <linux/atmel-mci.h>
34 #include <linux/atmel_pdc.h>
35 #include <linux/pm.h>
36 #include <linux/pm_runtime.h>
37 #include <linux/pinctrl/consumer.h>
38
39 #include <asm/cacheflush.h>
40 #include <asm/io.h>
41 #include <asm/unaligned.h>
42
43 /*
44 * Superset of MCI IP registers integrated in Atmel AT91 Processor
45 * Registers and bitfields marked with [2] are only available in MCI2
46 */
47
48 /* MCI Register Definitions */
49 #define ATMCI_CR 0x0000 /* Control */
50 #define ATMCI_CR_MCIEN BIT(0) /* MCI Enable */
51 #define ATMCI_CR_MCIDIS BIT(1) /* MCI Disable */
52 #define ATMCI_CR_PWSEN BIT(2) /* Power Save Enable */
53 #define ATMCI_CR_PWSDIS BIT(3) /* Power Save Disable */
54 #define ATMCI_CR_SWRST BIT(7) /* Software Reset */
55 #define ATMCI_MR 0x0004 /* Mode */
56 #define ATMCI_MR_CLKDIV(x) ((x) << 0) /* Clock Divider */
57 #define ATMCI_MR_PWSDIV(x) ((x) << 8) /* Power Saving Divider */
58 #define ATMCI_MR_RDPROOF BIT(11) /* Read Proof */
59 #define ATMCI_MR_WRPROOF BIT(12) /* Write Proof */
60 #define ATMCI_MR_PDCFBYTE BIT(13) /* Force Byte Transfer */
61 #define ATMCI_MR_PDCPADV BIT(14) /* Padding Value */
62 #define ATMCI_MR_PDCMODE BIT(15) /* PDC-oriented Mode */
63 #define ATMCI_MR_CLKODD(x) ((x) << 16) /* LSB of Clock Divider */
64 #define ATMCI_DTOR 0x0008 /* Data Timeout */
65 #define ATMCI_DTOCYC(x) ((x) << 0) /* Data Timeout Cycles */
66 #define ATMCI_DTOMUL(x) ((x) << 4) /* Data Timeout Multiplier */
67 #define ATMCI_SDCR 0x000c /* SD Card / SDIO */
68 #define ATMCI_SDCSEL_SLOT_A (0 << 0) /* Select SD slot A */
69 #define ATMCI_SDCSEL_SLOT_B (1 << 0) /* Select SD slot A */
70 #define ATMCI_SDCSEL_MASK (3 << 0)
71 #define ATMCI_SDCBUS_1BIT (0 << 6) /* 1-bit data bus */
72 #define ATMCI_SDCBUS_4BIT (2 << 6) /* 4-bit data bus */
73 #define ATMCI_SDCBUS_8BIT (3 << 6) /* 8-bit data bus[2] */
74 #define ATMCI_SDCBUS_MASK (3 << 6)
75 #define ATMCI_ARGR 0x0010 /* Command Argument */
76 #define ATMCI_CMDR 0x0014 /* Command */
77 #define ATMCI_CMDR_CMDNB(x) ((x) << 0) /* Command Opcode */
78 #define ATMCI_CMDR_RSPTYP_NONE (0 << 6) /* No response */
79 #define ATMCI_CMDR_RSPTYP_48BIT (1 << 6) /* 48-bit response */
80 #define ATMCI_CMDR_RSPTYP_136BIT (2 << 6) /* 136-bit response */
81 #define ATMCI_CMDR_SPCMD_INIT (1 << 8) /* Initialization command */
82 #define ATMCI_CMDR_SPCMD_SYNC (2 << 8) /* Synchronized command */
83 #define ATMCI_CMDR_SPCMD_INT (4 << 8) /* Interrupt command */
84 #define ATMCI_CMDR_SPCMD_INTRESP (5 << 8) /* Interrupt response */
85 #define ATMCI_CMDR_OPDCMD (1 << 11) /* Open Drain */
86 #define ATMCI_CMDR_MAXLAT_5CYC (0 << 12) /* Max latency 5 cycles */
87 #define ATMCI_CMDR_MAXLAT_64CYC (1 << 12) /* Max latency 64 cycles */
88 #define ATMCI_CMDR_START_XFER (1 << 16) /* Start data transfer */
89 #define ATMCI_CMDR_STOP_XFER (2 << 16) /* Stop data transfer */
90 #define ATMCI_CMDR_TRDIR_WRITE (0 << 18) /* Write data */
91 #define ATMCI_CMDR_TRDIR_READ (1 << 18) /* Read data */
92 #define ATMCI_CMDR_BLOCK (0 << 19) /* Single-block transfer */
93 #define ATMCI_CMDR_MULTI_BLOCK (1 << 19) /* Multi-block transfer */
94 #define ATMCI_CMDR_STREAM (2 << 19) /* MMC Stream transfer */
95 #define ATMCI_CMDR_SDIO_BYTE (4 << 19) /* SDIO Byte transfer */
96 #define ATMCI_CMDR_SDIO_BLOCK (5 << 19) /* SDIO Block transfer */
97 #define ATMCI_CMDR_SDIO_SUSPEND (1 << 24) /* SDIO Suspend Command */
98 #define ATMCI_CMDR_SDIO_RESUME (2 << 24) /* SDIO Resume Command */
99 #define ATMCI_BLKR 0x0018 /* Block */
100 #define ATMCI_BCNT(x) ((x) << 0) /* Data Block Count */
101 #define ATMCI_BLKLEN(x) ((x) << 16) /* Data Block Length */
102 #define ATMCI_CSTOR 0x001c /* Completion Signal Timeout[2] */
103 #define ATMCI_CSTOCYC(x) ((x) << 0) /* CST cycles */
104 #define ATMCI_CSTOMUL(x) ((x) << 4) /* CST multiplier */
105 #define ATMCI_RSPR 0x0020 /* Response 0 */
106 #define ATMCI_RSPR1 0x0024 /* Response 1 */
107 #define ATMCI_RSPR2 0x0028 /* Response 2 */
108 #define ATMCI_RSPR3 0x002c /* Response 3 */
109 #define ATMCI_RDR 0x0030 /* Receive Data */
110 #define ATMCI_TDR 0x0034 /* Transmit Data */
111 #define ATMCI_SR 0x0040 /* Status */
112 #define ATMCI_IER 0x0044 /* Interrupt Enable */
113 #define ATMCI_IDR 0x0048 /* Interrupt Disable */
114 #define ATMCI_IMR 0x004c /* Interrupt Mask */
115 #define ATMCI_CMDRDY BIT(0) /* Command Ready */
116 #define ATMCI_RXRDY BIT(1) /* Receiver Ready */
117 #define ATMCI_TXRDY BIT(2) /* Transmitter Ready */
118 #define ATMCI_BLKE BIT(3) /* Data Block Ended */
119 #define ATMCI_DTIP BIT(4) /* Data Transfer In Progress */
120 #define ATMCI_NOTBUSY BIT(5) /* Data Not Busy */
121 #define ATMCI_ENDRX BIT(6) /* End of RX Buffer */
122 #define ATMCI_ENDTX BIT(7) /* End of TX Buffer */
123 #define ATMCI_SDIOIRQA BIT(8) /* SDIO IRQ in slot A */
124 #define ATMCI_SDIOIRQB BIT(9) /* SDIO IRQ in slot B */
125 #define ATMCI_SDIOWAIT BIT(12) /* SDIO Read Wait Operation Status */
126 #define ATMCI_CSRCV BIT(13) /* CE-ATA Completion Signal Received */
127 #define ATMCI_RXBUFF BIT(14) /* RX Buffer Full */
128 #define ATMCI_TXBUFE BIT(15) /* TX Buffer Empty */
129 #define ATMCI_RINDE BIT(16) /* Response Index Error */
130 #define ATMCI_RDIRE BIT(17) /* Response Direction Error */
131 #define ATMCI_RCRCE BIT(18) /* Response CRC Error */
132 #define ATMCI_RENDE BIT(19) /* Response End Bit Error */
133 #define ATMCI_RTOE BIT(20) /* Response Time-Out Error */
134 #define ATMCI_DCRCE BIT(21) /* Data CRC Error */
135 #define ATMCI_DTOE BIT(22) /* Data Time-Out Error */
136 #define ATMCI_CSTOE BIT(23) /* Completion Signal Time-out Error */
137 #define ATMCI_BLKOVRE BIT(24) /* DMA Block Overrun Error */
138 #define ATMCI_DMADONE BIT(25) /* DMA Transfer Done */
139 #define ATMCI_FIFOEMPTY BIT(26) /* FIFO Empty Flag */
140 #define ATMCI_XFRDONE BIT(27) /* Transfer Done Flag */
141 #define ATMCI_ACKRCV BIT(28) /* Boot Operation Acknowledge Received */
142 #define ATMCI_ACKRCVE BIT(29) /* Boot Operation Acknowledge Error */
143 #define ATMCI_OVRE BIT(30) /* RX Overrun Error */
144 #define ATMCI_UNRE BIT(31) /* TX Underrun Error */
145 #define ATMCI_DMA 0x0050 /* DMA Configuration[2] */
146 #define ATMCI_DMA_OFFSET(x) ((x) << 0) /* DMA Write Buffer Offset */
147 #define ATMCI_DMA_CHKSIZE(x) ((x) << 4) /* DMA Channel Read and Write Chunk Size */
148 #define ATMCI_DMAEN BIT(8) /* DMA Hardware Handshaking Enable */
149 #define ATMCI_CFG 0x0054 /* Configuration[2] */
150 #define ATMCI_CFG_FIFOMODE_1DATA BIT(0) /* MCI Internal FIFO control mode */
151 #define ATMCI_CFG_FERRCTRL_COR BIT(4) /* Flow Error flag reset control mode */
152 #define ATMCI_CFG_HSMODE BIT(8) /* High Speed Mode */
153 #define ATMCI_CFG_LSYNC BIT(12) /* Synchronize on the last block */
154 #define ATMCI_WPMR 0x00e4 /* Write Protection Mode[2] */
155 #define ATMCI_WP_EN BIT(0) /* WP Enable */
156 #define ATMCI_WP_KEY (0x4d4349 << 8) /* WP Key */
157 #define ATMCI_WPSR 0x00e8 /* Write Protection Status[2] */
158 #define ATMCI_GET_WP_VS(x) ((x) & 0x0f)
159 #define ATMCI_GET_WP_VSRC(x) (((x) >> 8) & 0xffff)
160 #define ATMCI_VERSION 0x00FC /* Version */
161 #define ATMCI_FIFO_APERTURE 0x0200 /* FIFO Aperture[2] */
162
163 /* This is not including the FIFO Aperture on MCI2 */
164 #define ATMCI_REGS_SIZE 0x100
165
166 /* Register access macros */
167 #define atmci_readl(port, reg) \
168 __raw_readl((port)->regs + reg)
169 #define atmci_writel(port, reg, value) \
170 __raw_writel((value), (port)->regs + reg)
171
172 #define ATMCI_CMD_TIMEOUT_MS 2000
173 #define AUTOSUSPEND_DELAY 50
174
175 #define ATMCI_DATA_ERROR_FLAGS (ATMCI_DCRCE | ATMCI_DTOE | ATMCI_OVRE | ATMCI_UNRE)
176 #define ATMCI_DMA_THRESHOLD 16
177
178 enum {
179 EVENT_CMD_RDY = 0,
180 EVENT_XFER_COMPLETE,
181 EVENT_NOTBUSY,
182 EVENT_DATA_ERROR,
183 };
184
185 enum atmel_mci_state {
186 STATE_IDLE = 0,
187 STATE_SENDING_CMD,
188 STATE_DATA_XFER,
189 STATE_WAITING_NOTBUSY,
190 STATE_SENDING_STOP,
191 STATE_END_REQUEST,
192 };
193
194 enum atmci_xfer_dir {
195 XFER_RECEIVE = 0,
196 XFER_TRANSMIT,
197 };
198
199 enum atmci_pdc_buf {
200 PDC_FIRST_BUF = 0,
201 PDC_SECOND_BUF,
202 };
203
204 struct atmel_mci_caps {
205 bool has_dma_conf_reg;
206 bool has_pdc;
207 bool has_cfg_reg;
208 bool has_cstor_reg;
209 bool has_highspeed;
210 bool has_rwproof;
211 bool has_odd_clk_div;
212 bool has_bad_data_ordering;
213 bool need_reset_after_xfer;
214 bool need_blksz_mul_4;
215 bool need_notbusy_for_read_ops;
216 };
217
218 struct atmel_mci_dma {
219 struct dma_chan *chan;
220 struct dma_async_tx_descriptor *data_desc;
221 };
222
223 /**
224 * struct atmel_mci - MMC controller state shared between all slots
225 * @lock: Spinlock protecting the queue and associated data.
226 * @regs: Pointer to MMIO registers.
227 * @sg: Scatterlist entry currently being processed by PIO or PDC code.
228 * @sg_len: Size of the scatterlist
229 * @pio_offset: Offset into the current scatterlist entry.
230 * @buffer: Buffer used if we don't have the r/w proof capability. We
231 * don't have the time to switch pdc buffers so we have to use only
232 * one buffer for the full transaction.
233 * @buf_size: size of the buffer.
234 * @buf_phys_addr: buffer address needed for pdc.
235 * @cur_slot: The slot which is currently using the controller.
236 * @mrq: The request currently being processed on @cur_slot,
237 * or NULL if the controller is idle.
238 * @cmd: The command currently being sent to the card, or NULL.
239 * @data: The data currently being transferred, or NULL if no data
240 * transfer is in progress.
241 * @data_size: just data->blocks * data->blksz.
242 * @dma: DMA client state.
243 * @data_chan: DMA channel being used for the current data transfer.
244 * @dma_conf: Configuration for the DMA slave
245 * @cmd_status: Snapshot of SR taken upon completion of the current
246 * command. Only valid when EVENT_CMD_COMPLETE is pending.
247 * @data_status: Snapshot of SR taken upon completion of the current
248 * data transfer. Only valid when EVENT_DATA_COMPLETE or
249 * EVENT_DATA_ERROR is pending.
250 * @stop_cmdr: Value to be loaded into CMDR when the stop command is
251 * to be sent.
252 * @tasklet: Tasklet running the request state machine.
253 * @pending_events: Bitmask of events flagged by the interrupt handler
254 * to be processed by the tasklet.
255 * @completed_events: Bitmask of events which the state machine has
256 * processed.
257 * @state: Tasklet state.
258 * @queue: List of slots waiting for access to the controller.
259 * @need_clock_update: Update the clock rate before the next request.
260 * @need_reset: Reset controller before next request.
261 * @timer: Timer to balance the data timeout error flag which cannot rise.
262 * @mode_reg: Value of the MR register.
263 * @cfg_reg: Value of the CFG register.
264 * @bus_hz: The rate of @mck in Hz. This forms the basis for MMC bus
265 * rate and timeout calculations.
266 * @mapbase: Physical address of the MMIO registers.
267 * @mck: The peripheral bus clock hooked up to the MMC controller.
268 * @pdev: Platform device associated with the MMC controller.
269 * @slot: Slots sharing this MMC controller.
270 * @caps: MCI capabilities depending on MCI version.
271 * @prepare_data: function to setup MCI before data transfer which
272 * depends on MCI capabilities.
273 * @submit_data: function to start data transfer which depends on MCI
274 * capabilities.
275 * @stop_transfer: function to stop data transfer which depends on MCI
276 * capabilities.
277 *
278 * Locking
279 * =======
280 *
281 * @lock is a softirq-safe spinlock protecting @queue as well as
282 * @cur_slot, @mrq and @state. These must always be updated
283 * at the same time while holding @lock.
284 *
285 * @lock also protects mode_reg and need_clock_update since these are
286 * used to synchronize mode register updates with the queue
287 * processing.
288 *
289 * The @mrq field of struct atmel_mci_slot is also protected by @lock,
290 * and must always be written at the same time as the slot is added to
291 * @queue.
292 *
293 * @pending_events and @completed_events are accessed using atomic bit
294 * operations, so they don't need any locking.
295 *
296 * None of the fields touched by the interrupt handler need any
297 * locking. However, ordering is important: Before EVENT_DATA_ERROR or
298 * EVENT_DATA_COMPLETE is set in @pending_events, all data-related
299 * interrupts must be disabled and @data_status updated with a
300 * snapshot of SR. Similarly, before EVENT_CMD_COMPLETE is set, the
301 * CMDRDY interrupt must be disabled and @cmd_status updated with a
302 * snapshot of SR, and before EVENT_XFER_COMPLETE can be set, the
303 * bytes_xfered field of @data must be written. This is ensured by
304 * using barriers.
305 */
306 struct atmel_mci {
307 spinlock_t lock;
308 void __iomem *regs;
309
310 struct scatterlist *sg;
311 unsigned int sg_len;
312 unsigned int pio_offset;
313 unsigned int *buffer;
314 unsigned int buf_size;
315 dma_addr_t buf_phys_addr;
316
317 struct atmel_mci_slot *cur_slot;
318 struct mmc_request *mrq;
319 struct mmc_command *cmd;
320 struct mmc_data *data;
321 unsigned int data_size;
322
323 struct atmel_mci_dma dma;
324 struct dma_chan *data_chan;
325 struct dma_slave_config dma_conf;
326
327 u32 cmd_status;
328 u32 data_status;
329 u32 stop_cmdr;
330
331 struct tasklet_struct tasklet;
332 unsigned long pending_events;
333 unsigned long completed_events;
334 enum atmel_mci_state state;
335 struct list_head queue;
336
337 bool need_clock_update;
338 bool need_reset;
339 struct timer_list timer;
340 u32 mode_reg;
341 u32 cfg_reg;
342 unsigned long bus_hz;
343 unsigned long mapbase;
344 struct clk *mck;
345 struct platform_device *pdev;
346
347 struct atmel_mci_slot *slot[ATMCI_MAX_NR_SLOTS];
348
349 struct atmel_mci_caps caps;
350
351 u32 (*prepare_data)(struct atmel_mci *host, struct mmc_data *data);
352 void (*submit_data)(struct atmel_mci *host, struct mmc_data *data);
353 void (*stop_transfer)(struct atmel_mci *host);
354 };
355
356 /**
357 * struct atmel_mci_slot - MMC slot state
358 * @mmc: The mmc_host representing this slot.
359 * @host: The MMC controller this slot is using.
360 * @sdc_reg: Value of SDCR to be written before using this slot.
361 * @sdio_irq: SDIO irq mask for this slot.
362 * @mrq: mmc_request currently being processed or waiting to be
363 * processed, or NULL when the slot is idle.
364 * @queue_node: List node for placing this node in the @queue list of
365 * &struct atmel_mci.
366 * @clock: Clock rate configured by set_ios(). Protected by host->lock.
367 * @flags: Random state bits associated with the slot.
368 * @detect_pin: GPIO pin used for card detection, or negative if not
369 * available.
370 * @wp_pin: GPIO pin used for card write protect sending, or negative
371 * if not available.
372 * @detect_is_active_high: The state of the detect pin when it is active.
373 * @detect_timer: Timer used for debouncing @detect_pin interrupts.
374 */
375 struct atmel_mci_slot {
376 struct mmc_host *mmc;
377 struct atmel_mci *host;
378
379 u32 sdc_reg;
380 u32 sdio_irq;
381
382 struct mmc_request *mrq;
383 struct list_head queue_node;
384
385 unsigned int clock;
386 unsigned long flags;
387 #define ATMCI_CARD_PRESENT 0
388 #define ATMCI_CARD_NEED_INIT 1
389 #define ATMCI_SHUTDOWN 2
390
391 int detect_pin;
392 int wp_pin;
393 bool detect_is_active_high;
394
395 struct timer_list detect_timer;
396 };
397
398 #define atmci_test_and_clear_pending(host, event) \
399 test_and_clear_bit(event, &host->pending_events)
400 #define atmci_set_completed(host, event) \
401 set_bit(event, &host->completed_events)
402 #define atmci_set_pending(host, event) \
403 set_bit(event, &host->pending_events)
404
405 /*
406 * The debugfs stuff below is mostly optimized away when
407 * CONFIG_DEBUG_FS is not set.
408 */
atmci_req_show(struct seq_file * s,void * v)409 static int atmci_req_show(struct seq_file *s, void *v)
410 {
411 struct atmel_mci_slot *slot = s->private;
412 struct mmc_request *mrq;
413 struct mmc_command *cmd;
414 struct mmc_command *stop;
415 struct mmc_data *data;
416
417 /* Make sure we get a consistent snapshot */
418 spin_lock_bh(&slot->host->lock);
419 mrq = slot->mrq;
420
421 if (mrq) {
422 cmd = mrq->cmd;
423 data = mrq->data;
424 stop = mrq->stop;
425
426 if (cmd)
427 seq_printf(s,
428 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
429 cmd->opcode, cmd->arg, cmd->flags,
430 cmd->resp[0], cmd->resp[1], cmd->resp[2],
431 cmd->resp[3], cmd->error);
432 if (data)
433 seq_printf(s, "DATA %u / %u * %u flg %x err %d\n",
434 data->bytes_xfered, data->blocks,
435 data->blksz, data->flags, data->error);
436 if (stop)
437 seq_printf(s,
438 "CMD%u(0x%x) flg %x rsp %x %x %x %x err %d\n",
439 stop->opcode, stop->arg, stop->flags,
440 stop->resp[0], stop->resp[1], stop->resp[2],
441 stop->resp[3], stop->error);
442 }
443
444 spin_unlock_bh(&slot->host->lock);
445
446 return 0;
447 }
448
449 DEFINE_SHOW_ATTRIBUTE(atmci_req);
450
atmci_show_status_reg(struct seq_file * s,const char * regname,u32 value)451 static void atmci_show_status_reg(struct seq_file *s,
452 const char *regname, u32 value)
453 {
454 static const char *sr_bit[] = {
455 [0] = "CMDRDY",
456 [1] = "RXRDY",
457 [2] = "TXRDY",
458 [3] = "BLKE",
459 [4] = "DTIP",
460 [5] = "NOTBUSY",
461 [6] = "ENDRX",
462 [7] = "ENDTX",
463 [8] = "SDIOIRQA",
464 [9] = "SDIOIRQB",
465 [12] = "SDIOWAIT",
466 [14] = "RXBUFF",
467 [15] = "TXBUFE",
468 [16] = "RINDE",
469 [17] = "RDIRE",
470 [18] = "RCRCE",
471 [19] = "RENDE",
472 [20] = "RTOE",
473 [21] = "DCRCE",
474 [22] = "DTOE",
475 [23] = "CSTOE",
476 [24] = "BLKOVRE",
477 [25] = "DMADONE",
478 [26] = "FIFOEMPTY",
479 [27] = "XFRDONE",
480 [30] = "OVRE",
481 [31] = "UNRE",
482 };
483 unsigned int i;
484
485 seq_printf(s, "%s:\t0x%08x", regname, value);
486 for (i = 0; i < ARRAY_SIZE(sr_bit); i++) {
487 if (value & (1 << i)) {
488 if (sr_bit[i])
489 seq_printf(s, " %s", sr_bit[i]);
490 else
491 seq_puts(s, " UNKNOWN");
492 }
493 }
494 seq_putc(s, '\n');
495 }
496
atmci_regs_show(struct seq_file * s,void * v)497 static int atmci_regs_show(struct seq_file *s, void *v)
498 {
499 struct atmel_mci *host = s->private;
500 u32 *buf;
501 int ret = 0;
502
503
504 buf = kmalloc(ATMCI_REGS_SIZE, GFP_KERNEL);
505 if (!buf)
506 return -ENOMEM;
507
508 pm_runtime_get_sync(&host->pdev->dev);
509
510 /*
511 * Grab a more or less consistent snapshot. Note that we're
512 * not disabling interrupts, so IMR and SR may not be
513 * consistent.
514 */
515 spin_lock_bh(&host->lock);
516 memcpy_fromio(buf, host->regs, ATMCI_REGS_SIZE);
517 spin_unlock_bh(&host->lock);
518
519 pm_runtime_mark_last_busy(&host->pdev->dev);
520 pm_runtime_put_autosuspend(&host->pdev->dev);
521
522 seq_printf(s, "MR:\t0x%08x%s%s ",
523 buf[ATMCI_MR / 4],
524 buf[ATMCI_MR / 4] & ATMCI_MR_RDPROOF ? " RDPROOF" : "",
525 buf[ATMCI_MR / 4] & ATMCI_MR_WRPROOF ? " WRPROOF" : "");
526 if (host->caps.has_odd_clk_div)
527 seq_printf(s, "{CLKDIV,CLKODD}=%u\n",
528 ((buf[ATMCI_MR / 4] & 0xff) << 1)
529 | ((buf[ATMCI_MR / 4] >> 16) & 1));
530 else
531 seq_printf(s, "CLKDIV=%u\n",
532 (buf[ATMCI_MR / 4] & 0xff));
533 seq_printf(s, "DTOR:\t0x%08x\n", buf[ATMCI_DTOR / 4]);
534 seq_printf(s, "SDCR:\t0x%08x\n", buf[ATMCI_SDCR / 4]);
535 seq_printf(s, "ARGR:\t0x%08x\n", buf[ATMCI_ARGR / 4]);
536 seq_printf(s, "BLKR:\t0x%08x BCNT=%u BLKLEN=%u\n",
537 buf[ATMCI_BLKR / 4],
538 buf[ATMCI_BLKR / 4] & 0xffff,
539 (buf[ATMCI_BLKR / 4] >> 16) & 0xffff);
540 if (host->caps.has_cstor_reg)
541 seq_printf(s, "CSTOR:\t0x%08x\n", buf[ATMCI_CSTOR / 4]);
542
543 /* Don't read RSPR and RDR; it will consume the data there */
544
545 atmci_show_status_reg(s, "SR", buf[ATMCI_SR / 4]);
546 atmci_show_status_reg(s, "IMR", buf[ATMCI_IMR / 4]);
547
548 if (host->caps.has_dma_conf_reg) {
549 u32 val;
550
551 val = buf[ATMCI_DMA / 4];
552 seq_printf(s, "DMA:\t0x%08x OFFSET=%u CHKSIZE=%u%s\n",
553 val, val & 3,
554 ((val >> 4) & 3) ?
555 1 << (((val >> 4) & 3) + 1) : 1,
556 val & ATMCI_DMAEN ? " DMAEN" : "");
557 }
558 if (host->caps.has_cfg_reg) {
559 u32 val;
560
561 val = buf[ATMCI_CFG / 4];
562 seq_printf(s, "CFG:\t0x%08x%s%s%s%s\n",
563 val,
564 val & ATMCI_CFG_FIFOMODE_1DATA ? " FIFOMODE_ONE_DATA" : "",
565 val & ATMCI_CFG_FERRCTRL_COR ? " FERRCTRL_CLEAR_ON_READ" : "",
566 val & ATMCI_CFG_HSMODE ? " HSMODE" : "",
567 val & ATMCI_CFG_LSYNC ? " LSYNC" : "");
568 }
569
570 kfree(buf);
571
572 return ret;
573 }
574
575 DEFINE_SHOW_ATTRIBUTE(atmci_regs);
576
atmci_init_debugfs(struct atmel_mci_slot * slot)577 static void atmci_init_debugfs(struct atmel_mci_slot *slot)
578 {
579 struct mmc_host *mmc = slot->mmc;
580 struct atmel_mci *host = slot->host;
581 struct dentry *root;
582
583 root = mmc->debugfs_root;
584 if (!root)
585 return;
586
587 debugfs_create_file("regs", S_IRUSR, root, host, &atmci_regs_fops);
588 debugfs_create_file("req", S_IRUSR, root, slot, &atmci_req_fops);
589 debugfs_create_u32("state", S_IRUSR, root, &host->state);
590 debugfs_create_xul("pending_events", S_IRUSR, root,
591 &host->pending_events);
592 debugfs_create_xul("completed_events", S_IRUSR, root,
593 &host->completed_events);
594 }
595
596 #if defined(CONFIG_OF)
597 static const struct of_device_id atmci_dt_ids[] = {
598 { .compatible = "atmel,hsmci" },
599 { /* sentinel */ }
600 };
601
602 MODULE_DEVICE_TABLE(of, atmci_dt_ids);
603
604 static struct mci_platform_data*
atmci_of_init(struct platform_device * pdev)605 atmci_of_init(struct platform_device *pdev)
606 {
607 struct device_node *np = pdev->dev.of_node;
608 struct device_node *cnp;
609 struct mci_platform_data *pdata;
610 u32 slot_id;
611
612 if (!np) {
613 dev_err(&pdev->dev, "device node not found\n");
614 return ERR_PTR(-EINVAL);
615 }
616
617 pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
618 if (!pdata)
619 return ERR_PTR(-ENOMEM);
620
621 for_each_child_of_node(np, cnp) {
622 if (of_property_read_u32(cnp, "reg", &slot_id)) {
623 dev_warn(&pdev->dev, "reg property is missing for %pOF\n",
624 cnp);
625 continue;
626 }
627
628 if (slot_id >= ATMCI_MAX_NR_SLOTS) {
629 dev_warn(&pdev->dev, "can't have more than %d slots\n",
630 ATMCI_MAX_NR_SLOTS);
631 of_node_put(cnp);
632 break;
633 }
634
635 if (of_property_read_u32(cnp, "bus-width",
636 &pdata->slot[slot_id].bus_width))
637 pdata->slot[slot_id].bus_width = 1;
638
639 pdata->slot[slot_id].detect_pin =
640 of_get_named_gpio(cnp, "cd-gpios", 0);
641
642 pdata->slot[slot_id].detect_is_active_high =
643 of_property_read_bool(cnp, "cd-inverted");
644
645 pdata->slot[slot_id].non_removable =
646 of_property_read_bool(cnp, "non-removable");
647
648 pdata->slot[slot_id].wp_pin =
649 of_get_named_gpio(cnp, "wp-gpios", 0);
650 }
651
652 return pdata;
653 }
654 #else /* CONFIG_OF */
655 static inline struct mci_platform_data*
atmci_of_init(struct platform_device * dev)656 atmci_of_init(struct platform_device *dev)
657 {
658 return ERR_PTR(-EINVAL);
659 }
660 #endif
661
atmci_get_version(struct atmel_mci * host)662 static inline unsigned int atmci_get_version(struct atmel_mci *host)
663 {
664 return atmci_readl(host, ATMCI_VERSION) & 0x00000fff;
665 }
666
667 /*
668 * Fix sconfig's burst size according to atmel MCI. We need to convert them as:
669 * 1 -> 0, 4 -> 1, 8 -> 2, 16 -> 3.
670 * With version 0x600, we need to convert them as: 1 -> 0, 2 -> 1, 4 -> 2,
671 * 8 -> 3, 16 -> 4.
672 *
673 * This can be done by finding most significant bit set.
674 */
atmci_convert_chksize(struct atmel_mci * host,unsigned int maxburst)675 static inline unsigned int atmci_convert_chksize(struct atmel_mci *host,
676 unsigned int maxburst)
677 {
678 unsigned int version = atmci_get_version(host);
679 unsigned int offset = 2;
680
681 if (version >= 0x600)
682 offset = 1;
683
684 if (maxburst > 1)
685 return fls(maxburst) - offset;
686 else
687 return 0;
688 }
689
atmci_timeout_timer(struct timer_list * t)690 static void atmci_timeout_timer(struct timer_list *t)
691 {
692 struct atmel_mci *host;
693
694 host = from_timer(host, t, timer);
695
696 dev_dbg(&host->pdev->dev, "software timeout\n");
697
698 if (host->mrq->cmd->data) {
699 host->mrq->cmd->data->error = -ETIMEDOUT;
700 host->data = NULL;
701 /*
702 * With some SDIO modules, sometimes DMA transfer hangs. If
703 * stop_transfer() is not called then the DMA request is not
704 * removed, following ones are queued and never computed.
705 */
706 if (host->state == STATE_DATA_XFER)
707 host->stop_transfer(host);
708 } else {
709 host->mrq->cmd->error = -ETIMEDOUT;
710 host->cmd = NULL;
711 }
712 host->need_reset = 1;
713 host->state = STATE_END_REQUEST;
714 smp_wmb();
715 tasklet_schedule(&host->tasklet);
716 }
717
atmci_ns_to_clocks(struct atmel_mci * host,unsigned int ns)718 static inline unsigned int atmci_ns_to_clocks(struct atmel_mci *host,
719 unsigned int ns)
720 {
721 /*
722 * It is easier here to use us instead of ns for the timeout,
723 * it prevents from overflows during calculation.
724 */
725 unsigned int us = DIV_ROUND_UP(ns, 1000);
726
727 /* Maximum clock frequency is host->bus_hz/2 */
728 return us * (DIV_ROUND_UP(host->bus_hz, 2000000));
729 }
730
atmci_set_timeout(struct atmel_mci * host,struct atmel_mci_slot * slot,struct mmc_data * data)731 static void atmci_set_timeout(struct atmel_mci *host,
732 struct atmel_mci_slot *slot, struct mmc_data *data)
733 {
734 static unsigned dtomul_to_shift[] = {
735 0, 4, 7, 8, 10, 12, 16, 20
736 };
737 unsigned timeout;
738 unsigned dtocyc;
739 unsigned dtomul;
740
741 timeout = atmci_ns_to_clocks(host, data->timeout_ns)
742 + data->timeout_clks;
743
744 for (dtomul = 0; dtomul < 8; dtomul++) {
745 unsigned shift = dtomul_to_shift[dtomul];
746 dtocyc = (timeout + (1 << shift) - 1) >> shift;
747 if (dtocyc < 15)
748 break;
749 }
750
751 if (dtomul >= 8) {
752 dtomul = 7;
753 dtocyc = 15;
754 }
755
756 dev_vdbg(&slot->mmc->class_dev, "setting timeout to %u cycles\n",
757 dtocyc << dtomul_to_shift[dtomul]);
758 atmci_writel(host, ATMCI_DTOR, (ATMCI_DTOMUL(dtomul) | ATMCI_DTOCYC(dtocyc)));
759 }
760
761 /*
762 * Return mask with command flags to be enabled for this command.
763 */
atmci_prepare_command(struct mmc_host * mmc,struct mmc_command * cmd)764 static u32 atmci_prepare_command(struct mmc_host *mmc,
765 struct mmc_command *cmd)
766 {
767 struct mmc_data *data;
768 u32 cmdr;
769
770 cmd->error = -EINPROGRESS;
771
772 cmdr = ATMCI_CMDR_CMDNB(cmd->opcode);
773
774 if (cmd->flags & MMC_RSP_PRESENT) {
775 if (cmd->flags & MMC_RSP_136)
776 cmdr |= ATMCI_CMDR_RSPTYP_136BIT;
777 else
778 cmdr |= ATMCI_CMDR_RSPTYP_48BIT;
779 }
780
781 /*
782 * This should really be MAXLAT_5 for CMD2 and ACMD41, but
783 * it's too difficult to determine whether this is an ACMD or
784 * not. Better make it 64.
785 */
786 cmdr |= ATMCI_CMDR_MAXLAT_64CYC;
787
788 if (mmc->ios.bus_mode == MMC_BUSMODE_OPENDRAIN)
789 cmdr |= ATMCI_CMDR_OPDCMD;
790
791 data = cmd->data;
792 if (data) {
793 cmdr |= ATMCI_CMDR_START_XFER;
794
795 if (cmd->opcode == SD_IO_RW_EXTENDED) {
796 cmdr |= ATMCI_CMDR_SDIO_BLOCK;
797 } else {
798 if (data->blocks > 1)
799 cmdr |= ATMCI_CMDR_MULTI_BLOCK;
800 else
801 cmdr |= ATMCI_CMDR_BLOCK;
802 }
803
804 if (data->flags & MMC_DATA_READ)
805 cmdr |= ATMCI_CMDR_TRDIR_READ;
806 }
807
808 return cmdr;
809 }
810
atmci_send_command(struct atmel_mci * host,struct mmc_command * cmd,u32 cmd_flags)811 static void atmci_send_command(struct atmel_mci *host,
812 struct mmc_command *cmd, u32 cmd_flags)
813 {
814 unsigned int timeout_ms = cmd->busy_timeout ? cmd->busy_timeout :
815 ATMCI_CMD_TIMEOUT_MS;
816
817 WARN_ON(host->cmd);
818 host->cmd = cmd;
819
820 dev_vdbg(&host->pdev->dev,
821 "start command: ARGR=0x%08x CMDR=0x%08x\n",
822 cmd->arg, cmd_flags);
823
824 atmci_writel(host, ATMCI_ARGR, cmd->arg);
825 atmci_writel(host, ATMCI_CMDR, cmd_flags);
826
827 mod_timer(&host->timer, jiffies + msecs_to_jiffies(timeout_ms));
828 }
829
atmci_send_stop_cmd(struct atmel_mci * host,struct mmc_data * data)830 static void atmci_send_stop_cmd(struct atmel_mci *host, struct mmc_data *data)
831 {
832 dev_dbg(&host->pdev->dev, "send stop command\n");
833 atmci_send_command(host, data->stop, host->stop_cmdr);
834 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
835 }
836
837 /*
838 * Configure given PDC buffer taking care of alignement issues.
839 * Update host->data_size and host->sg.
840 */
atmci_pdc_set_single_buf(struct atmel_mci * host,enum atmci_xfer_dir dir,enum atmci_pdc_buf buf_nb)841 static void atmci_pdc_set_single_buf(struct atmel_mci *host,
842 enum atmci_xfer_dir dir, enum atmci_pdc_buf buf_nb)
843 {
844 u32 pointer_reg, counter_reg;
845 unsigned int buf_size;
846
847 if (dir == XFER_RECEIVE) {
848 pointer_reg = ATMEL_PDC_RPR;
849 counter_reg = ATMEL_PDC_RCR;
850 } else {
851 pointer_reg = ATMEL_PDC_TPR;
852 counter_reg = ATMEL_PDC_TCR;
853 }
854
855 if (buf_nb == PDC_SECOND_BUF) {
856 pointer_reg += ATMEL_PDC_SCND_BUF_OFF;
857 counter_reg += ATMEL_PDC_SCND_BUF_OFF;
858 }
859
860 if (!host->caps.has_rwproof) {
861 buf_size = host->buf_size;
862 atmci_writel(host, pointer_reg, host->buf_phys_addr);
863 } else {
864 buf_size = sg_dma_len(host->sg);
865 atmci_writel(host, pointer_reg, sg_dma_address(host->sg));
866 }
867
868 if (host->data_size <= buf_size) {
869 if (host->data_size & 0x3) {
870 /* If size is different from modulo 4, transfer bytes */
871 atmci_writel(host, counter_reg, host->data_size);
872 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCFBYTE);
873 } else {
874 /* Else transfer 32-bits words */
875 atmci_writel(host, counter_reg, host->data_size / 4);
876 }
877 host->data_size = 0;
878 } else {
879 /* We assume the size of a page is 32-bits aligned */
880 atmci_writel(host, counter_reg, sg_dma_len(host->sg) / 4);
881 host->data_size -= sg_dma_len(host->sg);
882 if (host->data_size)
883 host->sg = sg_next(host->sg);
884 }
885 }
886
887 /*
888 * Configure PDC buffer according to the data size ie configuring one or two
889 * buffers. Don't use this function if you want to configure only the second
890 * buffer. In this case, use atmci_pdc_set_single_buf.
891 */
atmci_pdc_set_both_buf(struct atmel_mci * host,int dir)892 static void atmci_pdc_set_both_buf(struct atmel_mci *host, int dir)
893 {
894 atmci_pdc_set_single_buf(host, dir, PDC_FIRST_BUF);
895 if (host->data_size)
896 atmci_pdc_set_single_buf(host, dir, PDC_SECOND_BUF);
897 }
898
899 /*
900 * Unmap sg lists, called when transfer is finished.
901 */
atmci_pdc_cleanup(struct atmel_mci * host)902 static void atmci_pdc_cleanup(struct atmel_mci *host)
903 {
904 struct mmc_data *data = host->data;
905
906 if (data)
907 dma_unmap_sg(&host->pdev->dev,
908 data->sg, data->sg_len,
909 mmc_get_dma_dir(data));
910 }
911
912 /*
913 * Disable PDC transfers. Update pending flags to EVENT_XFER_COMPLETE after
914 * having received ATMCI_TXBUFE or ATMCI_RXBUFF interrupt. Enable ATMCI_NOTBUSY
915 * interrupt needed for both transfer directions.
916 */
atmci_pdc_complete(struct atmel_mci * host)917 static void atmci_pdc_complete(struct atmel_mci *host)
918 {
919 int transfer_size = host->data->blocks * host->data->blksz;
920 int i;
921
922 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
923
924 if ((!host->caps.has_rwproof)
925 && (host->data->flags & MMC_DATA_READ)) {
926 if (host->caps.has_bad_data_ordering)
927 for (i = 0; i < transfer_size; i++)
928 host->buffer[i] = swab32(host->buffer[i]);
929 sg_copy_from_buffer(host->data->sg, host->data->sg_len,
930 host->buffer, transfer_size);
931 }
932
933 atmci_pdc_cleanup(host);
934
935 dev_dbg(&host->pdev->dev, "(%s) set pending xfer complete\n", __func__);
936 atmci_set_pending(host, EVENT_XFER_COMPLETE);
937 tasklet_schedule(&host->tasklet);
938 }
939
atmci_dma_cleanup(struct atmel_mci * host)940 static void atmci_dma_cleanup(struct atmel_mci *host)
941 {
942 struct mmc_data *data = host->data;
943
944 if (data)
945 dma_unmap_sg(host->dma.chan->device->dev,
946 data->sg, data->sg_len,
947 mmc_get_dma_dir(data));
948 }
949
950 /*
951 * This function is called by the DMA driver from tasklet context.
952 */
atmci_dma_complete(void * arg)953 static void atmci_dma_complete(void *arg)
954 {
955 struct atmel_mci *host = arg;
956 struct mmc_data *data = host->data;
957
958 dev_vdbg(&host->pdev->dev, "DMA complete\n");
959
960 if (host->caps.has_dma_conf_reg)
961 /* Disable DMA hardware handshaking on MCI */
962 atmci_writel(host, ATMCI_DMA, atmci_readl(host, ATMCI_DMA) & ~ATMCI_DMAEN);
963
964 atmci_dma_cleanup(host);
965
966 /*
967 * If the card was removed, data will be NULL. No point trying
968 * to send the stop command or waiting for NBUSY in this case.
969 */
970 if (data) {
971 dev_dbg(&host->pdev->dev,
972 "(%s) set pending xfer complete\n", __func__);
973 atmci_set_pending(host, EVENT_XFER_COMPLETE);
974 tasklet_schedule(&host->tasklet);
975
976 /*
977 * Regardless of what the documentation says, we have
978 * to wait for NOTBUSY even after block read
979 * operations.
980 *
981 * When the DMA transfer is complete, the controller
982 * may still be reading the CRC from the card, i.e.
983 * the data transfer is still in progress and we
984 * haven't seen all the potential error bits yet.
985 *
986 * The interrupt handler will schedule a different
987 * tasklet to finish things up when the data transfer
988 * is completely done.
989 *
990 * We may not complete the mmc request here anyway
991 * because the mmc layer may call back and cause us to
992 * violate the "don't submit new operations from the
993 * completion callback" rule of the dma engine
994 * framework.
995 */
996 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
997 }
998 }
999
1000 /*
1001 * Returns a mask of interrupt flags to be enabled after the whole
1002 * request has been prepared.
1003 */
atmci_prepare_data(struct atmel_mci * host,struct mmc_data * data)1004 static u32 atmci_prepare_data(struct atmel_mci *host, struct mmc_data *data)
1005 {
1006 u32 iflags;
1007
1008 data->error = -EINPROGRESS;
1009
1010 host->sg = data->sg;
1011 host->sg_len = data->sg_len;
1012 host->data = data;
1013 host->data_chan = NULL;
1014
1015 iflags = ATMCI_DATA_ERROR_FLAGS;
1016
1017 /*
1018 * Errata: MMC data write operation with less than 12
1019 * bytes is impossible.
1020 *
1021 * Errata: MCI Transmit Data Register (TDR) FIFO
1022 * corruption when length is not multiple of 4.
1023 */
1024 if (data->blocks * data->blksz < 12
1025 || (data->blocks * data->blksz) & 3)
1026 host->need_reset = true;
1027
1028 host->pio_offset = 0;
1029 if (data->flags & MMC_DATA_READ)
1030 iflags |= ATMCI_RXRDY;
1031 else
1032 iflags |= ATMCI_TXRDY;
1033
1034 return iflags;
1035 }
1036
1037 /*
1038 * Set interrupt flags and set block length into the MCI mode register even
1039 * if this value is also accessible in the MCI block register. It seems to be
1040 * necessary before the High Speed MCI version. It also map sg and configure
1041 * PDC registers.
1042 */
1043 static u32
atmci_prepare_data_pdc(struct atmel_mci * host,struct mmc_data * data)1044 atmci_prepare_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1045 {
1046 u32 iflags, tmp;
1047 int i;
1048
1049 data->error = -EINPROGRESS;
1050
1051 host->data = data;
1052 host->sg = data->sg;
1053 iflags = ATMCI_DATA_ERROR_FLAGS;
1054
1055 /* Enable pdc mode */
1056 atmci_writel(host, ATMCI_MR, host->mode_reg | ATMCI_MR_PDCMODE);
1057
1058 if (data->flags & MMC_DATA_READ)
1059 iflags |= ATMCI_ENDRX | ATMCI_RXBUFF;
1060 else
1061 iflags |= ATMCI_ENDTX | ATMCI_TXBUFE | ATMCI_BLKE;
1062
1063 /* Set BLKLEN */
1064 tmp = atmci_readl(host, ATMCI_MR);
1065 tmp &= 0x0000ffff;
1066 tmp |= ATMCI_BLKLEN(data->blksz);
1067 atmci_writel(host, ATMCI_MR, tmp);
1068
1069 /* Configure PDC */
1070 host->data_size = data->blocks * data->blksz;
1071 dma_map_sg(&host->pdev->dev, data->sg, data->sg_len,
1072 mmc_get_dma_dir(data));
1073
1074 if ((!host->caps.has_rwproof)
1075 && (host->data->flags & MMC_DATA_WRITE)) {
1076 sg_copy_to_buffer(host->data->sg, host->data->sg_len,
1077 host->buffer, host->data_size);
1078 if (host->caps.has_bad_data_ordering)
1079 for (i = 0; i < host->data_size; i++)
1080 host->buffer[i] = swab32(host->buffer[i]);
1081 }
1082
1083 if (host->data_size)
1084 atmci_pdc_set_both_buf(host, data->flags & MMC_DATA_READ ?
1085 XFER_RECEIVE : XFER_TRANSMIT);
1086 return iflags;
1087 }
1088
1089 static u32
atmci_prepare_data_dma(struct atmel_mci * host,struct mmc_data * data)1090 atmci_prepare_data_dma(struct atmel_mci *host, struct mmc_data *data)
1091 {
1092 struct dma_chan *chan;
1093 struct dma_async_tx_descriptor *desc;
1094 struct scatterlist *sg;
1095 unsigned int i;
1096 enum dma_transfer_direction slave_dirn;
1097 unsigned int sglen;
1098 u32 maxburst;
1099 u32 iflags;
1100
1101 data->error = -EINPROGRESS;
1102
1103 WARN_ON(host->data);
1104 host->sg = NULL;
1105 host->data = data;
1106
1107 iflags = ATMCI_DATA_ERROR_FLAGS;
1108
1109 /*
1110 * We don't do DMA on "complex" transfers, i.e. with
1111 * non-word-aligned buffers or lengths. Also, we don't bother
1112 * with all the DMA setup overhead for short transfers.
1113 */
1114 if (data->blocks * data->blksz < ATMCI_DMA_THRESHOLD)
1115 return atmci_prepare_data(host, data);
1116 if (data->blksz & 3)
1117 return atmci_prepare_data(host, data);
1118
1119 for_each_sg(data->sg, sg, data->sg_len, i) {
1120 if (sg->offset & 3 || sg->length & 3)
1121 return atmci_prepare_data(host, data);
1122 }
1123
1124 /* If we don't have a channel, we can't do DMA */
1125 if (!host->dma.chan)
1126 return -ENODEV;
1127
1128 chan = host->dma.chan;
1129 host->data_chan = chan;
1130
1131 if (data->flags & MMC_DATA_READ) {
1132 host->dma_conf.direction = slave_dirn = DMA_DEV_TO_MEM;
1133 maxburst = atmci_convert_chksize(host,
1134 host->dma_conf.src_maxburst);
1135 } else {
1136 host->dma_conf.direction = slave_dirn = DMA_MEM_TO_DEV;
1137 maxburst = atmci_convert_chksize(host,
1138 host->dma_conf.dst_maxburst);
1139 }
1140
1141 if (host->caps.has_dma_conf_reg)
1142 atmci_writel(host, ATMCI_DMA, ATMCI_DMA_CHKSIZE(maxburst) |
1143 ATMCI_DMAEN);
1144
1145 sglen = dma_map_sg(chan->device->dev, data->sg,
1146 data->sg_len, mmc_get_dma_dir(data));
1147
1148 dmaengine_slave_config(chan, &host->dma_conf);
1149 desc = dmaengine_prep_slave_sg(chan,
1150 data->sg, sglen, slave_dirn,
1151 DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1152 if (!desc)
1153 goto unmap_exit;
1154
1155 host->dma.data_desc = desc;
1156 desc->callback = atmci_dma_complete;
1157 desc->callback_param = host;
1158
1159 return iflags;
1160 unmap_exit:
1161 dma_unmap_sg(chan->device->dev, data->sg, data->sg_len,
1162 mmc_get_dma_dir(data));
1163 return -ENOMEM;
1164 }
1165
1166 static void
atmci_submit_data(struct atmel_mci * host,struct mmc_data * data)1167 atmci_submit_data(struct atmel_mci *host, struct mmc_data *data)
1168 {
1169 return;
1170 }
1171
1172 /*
1173 * Start PDC according to transfer direction.
1174 */
1175 static void
atmci_submit_data_pdc(struct atmel_mci * host,struct mmc_data * data)1176 atmci_submit_data_pdc(struct atmel_mci *host, struct mmc_data *data)
1177 {
1178 if (data->flags & MMC_DATA_READ)
1179 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTEN);
1180 else
1181 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_TXTEN);
1182 }
1183
1184 static void
atmci_submit_data_dma(struct atmel_mci * host,struct mmc_data * data)1185 atmci_submit_data_dma(struct atmel_mci *host, struct mmc_data *data)
1186 {
1187 struct dma_chan *chan = host->data_chan;
1188 struct dma_async_tx_descriptor *desc = host->dma.data_desc;
1189
1190 if (chan) {
1191 dmaengine_submit(desc);
1192 dma_async_issue_pending(chan);
1193 }
1194 }
1195
atmci_stop_transfer(struct atmel_mci * host)1196 static void atmci_stop_transfer(struct atmel_mci *host)
1197 {
1198 dev_dbg(&host->pdev->dev,
1199 "(%s) set pending xfer complete\n", __func__);
1200 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1201 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1202 }
1203
1204 /*
1205 * Stop data transfer because error(s) occurred.
1206 */
atmci_stop_transfer_pdc(struct atmel_mci * host)1207 static void atmci_stop_transfer_pdc(struct atmel_mci *host)
1208 {
1209 atmci_writel(host, ATMEL_PDC_PTCR, ATMEL_PDC_RXTDIS | ATMEL_PDC_TXTDIS);
1210 }
1211
atmci_stop_transfer_dma(struct atmel_mci * host)1212 static void atmci_stop_transfer_dma(struct atmel_mci *host)
1213 {
1214 struct dma_chan *chan = host->data_chan;
1215
1216 if (chan) {
1217 dmaengine_terminate_all(chan);
1218 atmci_dma_cleanup(host);
1219 } else {
1220 /* Data transfer was stopped by the interrupt handler */
1221 dev_dbg(&host->pdev->dev,
1222 "(%s) set pending xfer complete\n", __func__);
1223 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1224 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1225 }
1226 }
1227
1228 /*
1229 * Start a request: prepare data if needed, prepare the command and activate
1230 * interrupts.
1231 */
atmci_start_request(struct atmel_mci * host,struct atmel_mci_slot * slot)1232 static void atmci_start_request(struct atmel_mci *host,
1233 struct atmel_mci_slot *slot)
1234 {
1235 struct mmc_request *mrq;
1236 struct mmc_command *cmd;
1237 struct mmc_data *data;
1238 u32 iflags;
1239 u32 cmdflags;
1240
1241 mrq = slot->mrq;
1242 host->cur_slot = slot;
1243 host->mrq = mrq;
1244
1245 host->pending_events = 0;
1246 host->completed_events = 0;
1247 host->cmd_status = 0;
1248 host->data_status = 0;
1249
1250 dev_dbg(&host->pdev->dev, "start request: cmd %u\n", mrq->cmd->opcode);
1251
1252 if (host->need_reset || host->caps.need_reset_after_xfer) {
1253 iflags = atmci_readl(host, ATMCI_IMR);
1254 iflags &= (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB);
1255 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1256 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1257 atmci_writel(host, ATMCI_MR, host->mode_reg);
1258 if (host->caps.has_cfg_reg)
1259 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1260 atmci_writel(host, ATMCI_IER, iflags);
1261 host->need_reset = false;
1262 }
1263 atmci_writel(host, ATMCI_SDCR, slot->sdc_reg);
1264
1265 iflags = atmci_readl(host, ATMCI_IMR);
1266 if (iflags & ~(ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
1267 dev_dbg(&slot->mmc->class_dev, "WARNING: IMR=0x%08x\n",
1268 iflags);
1269
1270 if (unlikely(test_and_clear_bit(ATMCI_CARD_NEED_INIT, &slot->flags))) {
1271 /* Send init sequence (74 clock cycles) */
1272 atmci_writel(host, ATMCI_CMDR, ATMCI_CMDR_SPCMD_INIT);
1273 while (!(atmci_readl(host, ATMCI_SR) & ATMCI_CMDRDY))
1274 cpu_relax();
1275 }
1276 iflags = 0;
1277 data = mrq->data;
1278 if (data) {
1279 atmci_set_timeout(host, slot, data);
1280
1281 /* Must set block count/size before sending command */
1282 atmci_writel(host, ATMCI_BLKR, ATMCI_BCNT(data->blocks)
1283 | ATMCI_BLKLEN(data->blksz));
1284 dev_vdbg(&slot->mmc->class_dev, "BLKR=0x%08x\n",
1285 ATMCI_BCNT(data->blocks) | ATMCI_BLKLEN(data->blksz));
1286
1287 iflags |= host->prepare_data(host, data);
1288 }
1289
1290 iflags |= ATMCI_CMDRDY;
1291 cmd = mrq->cmd;
1292 cmdflags = atmci_prepare_command(slot->mmc, cmd);
1293
1294 /*
1295 * DMA transfer should be started before sending the command to avoid
1296 * unexpected errors especially for read operations in SDIO mode.
1297 * Unfortunately, in PDC mode, command has to be sent before starting
1298 * the transfer.
1299 */
1300 if (host->submit_data != &atmci_submit_data_dma)
1301 atmci_send_command(host, cmd, cmdflags);
1302
1303 if (data)
1304 host->submit_data(host, data);
1305
1306 if (host->submit_data == &atmci_submit_data_dma)
1307 atmci_send_command(host, cmd, cmdflags);
1308
1309 if (mrq->stop) {
1310 host->stop_cmdr = atmci_prepare_command(slot->mmc, mrq->stop);
1311 host->stop_cmdr |= ATMCI_CMDR_STOP_XFER;
1312 if (!(data->flags & MMC_DATA_WRITE))
1313 host->stop_cmdr |= ATMCI_CMDR_TRDIR_READ;
1314 host->stop_cmdr |= ATMCI_CMDR_MULTI_BLOCK;
1315 }
1316
1317 /*
1318 * We could have enabled interrupts earlier, but I suspect
1319 * that would open up a nice can of interesting race
1320 * conditions (e.g. command and data complete, but stop not
1321 * prepared yet.)
1322 */
1323 atmci_writel(host, ATMCI_IER, iflags);
1324 }
1325
atmci_queue_request(struct atmel_mci * host,struct atmel_mci_slot * slot,struct mmc_request * mrq)1326 static void atmci_queue_request(struct atmel_mci *host,
1327 struct atmel_mci_slot *slot, struct mmc_request *mrq)
1328 {
1329 dev_vdbg(&slot->mmc->class_dev, "queue request: state=%d\n",
1330 host->state);
1331
1332 spin_lock_bh(&host->lock);
1333 slot->mrq = mrq;
1334 if (host->state == STATE_IDLE) {
1335 host->state = STATE_SENDING_CMD;
1336 atmci_start_request(host, slot);
1337 } else {
1338 dev_dbg(&host->pdev->dev, "queue request\n");
1339 list_add_tail(&slot->queue_node, &host->queue);
1340 }
1341 spin_unlock_bh(&host->lock);
1342 }
1343
atmci_request(struct mmc_host * mmc,struct mmc_request * mrq)1344 static void atmci_request(struct mmc_host *mmc, struct mmc_request *mrq)
1345 {
1346 struct atmel_mci_slot *slot = mmc_priv(mmc);
1347 struct atmel_mci *host = slot->host;
1348 struct mmc_data *data;
1349
1350 WARN_ON(slot->mrq);
1351 dev_dbg(&host->pdev->dev, "MRQ: cmd %u\n", mrq->cmd->opcode);
1352
1353 /*
1354 * We may "know" the card is gone even though there's still an
1355 * electrical connection. If so, we really need to communicate
1356 * this to the MMC core since there won't be any more
1357 * interrupts as the card is completely removed. Otherwise,
1358 * the MMC core might believe the card is still there even
1359 * though the card was just removed very slowly.
1360 */
1361 if (!test_bit(ATMCI_CARD_PRESENT, &slot->flags)) {
1362 mrq->cmd->error = -ENOMEDIUM;
1363 mmc_request_done(mmc, mrq);
1364 return;
1365 }
1366
1367 /* We don't support multiple blocks of weird lengths. */
1368 data = mrq->data;
1369 if (data && data->blocks > 1 && data->blksz & 3) {
1370 mrq->cmd->error = -EINVAL;
1371 mmc_request_done(mmc, mrq);
1372 }
1373
1374 atmci_queue_request(host, slot, mrq);
1375 }
1376
atmci_set_ios(struct mmc_host * mmc,struct mmc_ios * ios)1377 static void atmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
1378 {
1379 struct atmel_mci_slot *slot = mmc_priv(mmc);
1380 struct atmel_mci *host = slot->host;
1381 unsigned int i;
1382
1383 slot->sdc_reg &= ~ATMCI_SDCBUS_MASK;
1384 switch (ios->bus_width) {
1385 case MMC_BUS_WIDTH_1:
1386 slot->sdc_reg |= ATMCI_SDCBUS_1BIT;
1387 break;
1388 case MMC_BUS_WIDTH_4:
1389 slot->sdc_reg |= ATMCI_SDCBUS_4BIT;
1390 break;
1391 case MMC_BUS_WIDTH_8:
1392 slot->sdc_reg |= ATMCI_SDCBUS_8BIT;
1393 break;
1394 }
1395
1396 if (ios->clock) {
1397 unsigned int clock_min = ~0U;
1398 int clkdiv;
1399
1400 spin_lock_bh(&host->lock);
1401 if (!host->mode_reg) {
1402 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1403 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1404 if (host->caps.has_cfg_reg)
1405 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1406 }
1407
1408 /*
1409 * Use mirror of ios->clock to prevent race with mmc
1410 * core ios update when finding the minimum.
1411 */
1412 slot->clock = ios->clock;
1413 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1414 if (host->slot[i] && host->slot[i]->clock
1415 && host->slot[i]->clock < clock_min)
1416 clock_min = host->slot[i]->clock;
1417 }
1418
1419 /* Calculate clock divider */
1420 if (host->caps.has_odd_clk_div) {
1421 clkdiv = DIV_ROUND_UP(host->bus_hz, clock_min) - 2;
1422 if (clkdiv < 0) {
1423 dev_warn(&mmc->class_dev,
1424 "clock %u too fast; using %lu\n",
1425 clock_min, host->bus_hz / 2);
1426 clkdiv = 0;
1427 } else if (clkdiv > 511) {
1428 dev_warn(&mmc->class_dev,
1429 "clock %u too slow; using %lu\n",
1430 clock_min, host->bus_hz / (511 + 2));
1431 clkdiv = 511;
1432 }
1433 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv >> 1)
1434 | ATMCI_MR_CLKODD(clkdiv & 1);
1435 } else {
1436 clkdiv = DIV_ROUND_UP(host->bus_hz, 2 * clock_min) - 1;
1437 if (clkdiv > 255) {
1438 dev_warn(&mmc->class_dev,
1439 "clock %u too slow; using %lu\n",
1440 clock_min, host->bus_hz / (2 * 256));
1441 clkdiv = 255;
1442 }
1443 host->mode_reg = ATMCI_MR_CLKDIV(clkdiv);
1444 }
1445
1446 /*
1447 * WRPROOF and RDPROOF prevent overruns/underruns by
1448 * stopping the clock when the FIFO is full/empty.
1449 * This state is not expected to last for long.
1450 */
1451 if (host->caps.has_rwproof)
1452 host->mode_reg |= (ATMCI_MR_WRPROOF | ATMCI_MR_RDPROOF);
1453
1454 if (host->caps.has_cfg_reg) {
1455 /* setup High Speed mode in relation with card capacity */
1456 if (ios->timing == MMC_TIMING_SD_HS)
1457 host->cfg_reg |= ATMCI_CFG_HSMODE;
1458 else
1459 host->cfg_reg &= ~ATMCI_CFG_HSMODE;
1460 }
1461
1462 if (list_empty(&host->queue)) {
1463 atmci_writel(host, ATMCI_MR, host->mode_reg);
1464 if (host->caps.has_cfg_reg)
1465 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1466 } else {
1467 host->need_clock_update = true;
1468 }
1469
1470 spin_unlock_bh(&host->lock);
1471 } else {
1472 bool any_slot_active = false;
1473
1474 spin_lock_bh(&host->lock);
1475 slot->clock = 0;
1476 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
1477 if (host->slot[i] && host->slot[i]->clock) {
1478 any_slot_active = true;
1479 break;
1480 }
1481 }
1482 if (!any_slot_active) {
1483 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
1484 if (host->mode_reg) {
1485 atmci_readl(host, ATMCI_MR);
1486 }
1487 host->mode_reg = 0;
1488 }
1489 spin_unlock_bh(&host->lock);
1490 }
1491
1492 switch (ios->power_mode) {
1493 case MMC_POWER_OFF:
1494 if (!IS_ERR(mmc->supply.vmmc))
1495 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
1496 break;
1497 case MMC_POWER_UP:
1498 set_bit(ATMCI_CARD_NEED_INIT, &slot->flags);
1499 if (!IS_ERR(mmc->supply.vmmc))
1500 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, ios->vdd);
1501 break;
1502 default:
1503 break;
1504 }
1505 }
1506
atmci_get_ro(struct mmc_host * mmc)1507 static int atmci_get_ro(struct mmc_host *mmc)
1508 {
1509 int read_only = -ENOSYS;
1510 struct atmel_mci_slot *slot = mmc_priv(mmc);
1511
1512 if (gpio_is_valid(slot->wp_pin)) {
1513 read_only = gpio_get_value(slot->wp_pin);
1514 dev_dbg(&mmc->class_dev, "card is %s\n",
1515 read_only ? "read-only" : "read-write");
1516 }
1517
1518 return read_only;
1519 }
1520
atmci_get_cd(struct mmc_host * mmc)1521 static int atmci_get_cd(struct mmc_host *mmc)
1522 {
1523 int present = -ENOSYS;
1524 struct atmel_mci_slot *slot = mmc_priv(mmc);
1525
1526 if (gpio_is_valid(slot->detect_pin)) {
1527 present = !(gpio_get_value(slot->detect_pin) ^
1528 slot->detect_is_active_high);
1529 dev_dbg(&mmc->class_dev, "card is %spresent\n",
1530 present ? "" : "not ");
1531 }
1532
1533 return present;
1534 }
1535
atmci_enable_sdio_irq(struct mmc_host * mmc,int enable)1536 static void atmci_enable_sdio_irq(struct mmc_host *mmc, int enable)
1537 {
1538 struct atmel_mci_slot *slot = mmc_priv(mmc);
1539 struct atmel_mci *host = slot->host;
1540
1541 if (enable)
1542 atmci_writel(host, ATMCI_IER, slot->sdio_irq);
1543 else
1544 atmci_writel(host, ATMCI_IDR, slot->sdio_irq);
1545 }
1546
1547 static const struct mmc_host_ops atmci_ops = {
1548 .request = atmci_request,
1549 .set_ios = atmci_set_ios,
1550 .get_ro = atmci_get_ro,
1551 .get_cd = atmci_get_cd,
1552 .enable_sdio_irq = atmci_enable_sdio_irq,
1553 };
1554
1555 /* Called with host->lock held */
atmci_request_end(struct atmel_mci * host,struct mmc_request * mrq)1556 static void atmci_request_end(struct atmel_mci *host, struct mmc_request *mrq)
1557 __releases(&host->lock)
1558 __acquires(&host->lock)
1559 {
1560 struct atmel_mci_slot *slot = NULL;
1561 struct mmc_host *prev_mmc = host->cur_slot->mmc;
1562
1563 WARN_ON(host->cmd || host->data);
1564
1565 del_timer(&host->timer);
1566
1567 /*
1568 * Update the MMC clock rate if necessary. This may be
1569 * necessary if set_ios() is called when a different slot is
1570 * busy transferring data.
1571 */
1572 if (host->need_clock_update) {
1573 atmci_writel(host, ATMCI_MR, host->mode_reg);
1574 if (host->caps.has_cfg_reg)
1575 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1576 }
1577
1578 host->cur_slot->mrq = NULL;
1579 host->mrq = NULL;
1580 if (!list_empty(&host->queue)) {
1581 slot = list_entry(host->queue.next,
1582 struct atmel_mci_slot, queue_node);
1583 list_del(&slot->queue_node);
1584 dev_vdbg(&host->pdev->dev, "list not empty: %s is next\n",
1585 mmc_hostname(slot->mmc));
1586 host->state = STATE_SENDING_CMD;
1587 atmci_start_request(host, slot);
1588 } else {
1589 dev_vdbg(&host->pdev->dev, "list empty\n");
1590 host->state = STATE_IDLE;
1591 }
1592
1593 spin_unlock(&host->lock);
1594 mmc_request_done(prev_mmc, mrq);
1595 spin_lock(&host->lock);
1596 }
1597
atmci_command_complete(struct atmel_mci * host,struct mmc_command * cmd)1598 static void atmci_command_complete(struct atmel_mci *host,
1599 struct mmc_command *cmd)
1600 {
1601 u32 status = host->cmd_status;
1602
1603 /* Read the response from the card (up to 16 bytes) */
1604 cmd->resp[0] = atmci_readl(host, ATMCI_RSPR);
1605 cmd->resp[1] = atmci_readl(host, ATMCI_RSPR);
1606 cmd->resp[2] = atmci_readl(host, ATMCI_RSPR);
1607 cmd->resp[3] = atmci_readl(host, ATMCI_RSPR);
1608
1609 if (status & ATMCI_RTOE)
1610 cmd->error = -ETIMEDOUT;
1611 else if ((cmd->flags & MMC_RSP_CRC) && (status & ATMCI_RCRCE))
1612 cmd->error = -EILSEQ;
1613 else if (status & (ATMCI_RINDE | ATMCI_RDIRE | ATMCI_RENDE))
1614 cmd->error = -EIO;
1615 else if (host->mrq->data && (host->mrq->data->blksz & 3)) {
1616 if (host->caps.need_blksz_mul_4) {
1617 cmd->error = -EINVAL;
1618 host->need_reset = 1;
1619 }
1620 } else
1621 cmd->error = 0;
1622 }
1623
atmci_detect_change(struct timer_list * t)1624 static void atmci_detect_change(struct timer_list *t)
1625 {
1626 struct atmel_mci_slot *slot = from_timer(slot, t, detect_timer);
1627 bool present;
1628 bool present_old;
1629
1630 /*
1631 * atmci_cleanup_slot() sets the ATMCI_SHUTDOWN flag before
1632 * freeing the interrupt. We must not re-enable the interrupt
1633 * if it has been freed, and if we're shutting down, it
1634 * doesn't really matter whether the card is present or not.
1635 */
1636 smp_rmb();
1637 if (test_bit(ATMCI_SHUTDOWN, &slot->flags))
1638 return;
1639
1640 enable_irq(gpio_to_irq(slot->detect_pin));
1641 present = !(gpio_get_value(slot->detect_pin) ^
1642 slot->detect_is_active_high);
1643 present_old = test_bit(ATMCI_CARD_PRESENT, &slot->flags);
1644
1645 dev_vdbg(&slot->mmc->class_dev, "detect change: %d (was %d)\n",
1646 present, present_old);
1647
1648 if (present != present_old) {
1649 struct atmel_mci *host = slot->host;
1650 struct mmc_request *mrq;
1651
1652 dev_dbg(&slot->mmc->class_dev, "card %s\n",
1653 present ? "inserted" : "removed");
1654
1655 spin_lock(&host->lock);
1656
1657 if (!present)
1658 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
1659 else
1660 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
1661
1662 /* Clean up queue if present */
1663 mrq = slot->mrq;
1664 if (mrq) {
1665 if (mrq == host->mrq) {
1666 /*
1667 * Reset controller to terminate any ongoing
1668 * commands or data transfers.
1669 */
1670 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
1671 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIEN);
1672 atmci_writel(host, ATMCI_MR, host->mode_reg);
1673 if (host->caps.has_cfg_reg)
1674 atmci_writel(host, ATMCI_CFG, host->cfg_reg);
1675
1676 host->data = NULL;
1677 host->cmd = NULL;
1678
1679 switch (host->state) {
1680 case STATE_IDLE:
1681 break;
1682 case STATE_SENDING_CMD:
1683 mrq->cmd->error = -ENOMEDIUM;
1684 if (mrq->data)
1685 host->stop_transfer(host);
1686 break;
1687 case STATE_DATA_XFER:
1688 mrq->data->error = -ENOMEDIUM;
1689 host->stop_transfer(host);
1690 break;
1691 case STATE_WAITING_NOTBUSY:
1692 mrq->data->error = -ENOMEDIUM;
1693 break;
1694 case STATE_SENDING_STOP:
1695 mrq->stop->error = -ENOMEDIUM;
1696 break;
1697 case STATE_END_REQUEST:
1698 break;
1699 }
1700
1701 atmci_request_end(host, mrq);
1702 } else {
1703 list_del(&slot->queue_node);
1704 mrq->cmd->error = -ENOMEDIUM;
1705 if (mrq->data)
1706 mrq->data->error = -ENOMEDIUM;
1707 if (mrq->stop)
1708 mrq->stop->error = -ENOMEDIUM;
1709
1710 spin_unlock(&host->lock);
1711 mmc_request_done(slot->mmc, mrq);
1712 spin_lock(&host->lock);
1713 }
1714 }
1715 spin_unlock(&host->lock);
1716
1717 mmc_detect_change(slot->mmc, 0);
1718 }
1719 }
1720
atmci_tasklet_func(struct tasklet_struct * t)1721 static void atmci_tasklet_func(struct tasklet_struct *t)
1722 {
1723 struct atmel_mci *host = from_tasklet(host, t, tasklet);
1724 struct mmc_request *mrq = host->mrq;
1725 struct mmc_data *data = host->data;
1726 enum atmel_mci_state state = host->state;
1727 enum atmel_mci_state prev_state;
1728 u32 status;
1729
1730 spin_lock(&host->lock);
1731
1732 state = host->state;
1733
1734 dev_vdbg(&host->pdev->dev,
1735 "tasklet: state %u pending/completed/mask %lx/%lx/%x\n",
1736 state, host->pending_events, host->completed_events,
1737 atmci_readl(host, ATMCI_IMR));
1738
1739 do {
1740 prev_state = state;
1741 dev_dbg(&host->pdev->dev, "FSM: state=%d\n", state);
1742
1743 switch (state) {
1744 case STATE_IDLE:
1745 break;
1746
1747 case STATE_SENDING_CMD:
1748 /*
1749 * Command has been sent, we are waiting for command
1750 * ready. Then we have three next states possible:
1751 * END_REQUEST by default, WAITING_NOTBUSY if it's a
1752 * command needing it or DATA_XFER if there is data.
1753 */
1754 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1755 if (!atmci_test_and_clear_pending(host,
1756 EVENT_CMD_RDY))
1757 break;
1758
1759 dev_dbg(&host->pdev->dev, "set completed cmd ready\n");
1760 host->cmd = NULL;
1761 atmci_set_completed(host, EVENT_CMD_RDY);
1762 atmci_command_complete(host, mrq->cmd);
1763 if (mrq->data) {
1764 dev_dbg(&host->pdev->dev,
1765 "command with data transfer");
1766 /*
1767 * If there is a command error don't start
1768 * data transfer.
1769 */
1770 if (mrq->cmd->error) {
1771 host->stop_transfer(host);
1772 host->data = NULL;
1773 atmci_writel(host, ATMCI_IDR,
1774 ATMCI_TXRDY | ATMCI_RXRDY
1775 | ATMCI_DATA_ERROR_FLAGS);
1776 state = STATE_END_REQUEST;
1777 } else
1778 state = STATE_DATA_XFER;
1779 } else if ((!mrq->data) && (mrq->cmd->flags & MMC_RSP_BUSY)) {
1780 dev_dbg(&host->pdev->dev,
1781 "command response need waiting notbusy");
1782 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1783 state = STATE_WAITING_NOTBUSY;
1784 } else
1785 state = STATE_END_REQUEST;
1786
1787 break;
1788
1789 case STATE_DATA_XFER:
1790 if (atmci_test_and_clear_pending(host,
1791 EVENT_DATA_ERROR)) {
1792 dev_dbg(&host->pdev->dev, "set completed data error\n");
1793 atmci_set_completed(host, EVENT_DATA_ERROR);
1794 state = STATE_END_REQUEST;
1795 break;
1796 }
1797
1798 /*
1799 * A data transfer is in progress. The event expected
1800 * to move to the next state depends of data transfer
1801 * type (PDC or DMA). Once transfer done we can move
1802 * to the next step which is WAITING_NOTBUSY in write
1803 * case and directly SENDING_STOP in read case.
1804 */
1805 dev_dbg(&host->pdev->dev, "FSM: xfer complete?\n");
1806 if (!atmci_test_and_clear_pending(host,
1807 EVENT_XFER_COMPLETE))
1808 break;
1809
1810 dev_dbg(&host->pdev->dev,
1811 "(%s) set completed xfer complete\n",
1812 __func__);
1813 atmci_set_completed(host, EVENT_XFER_COMPLETE);
1814
1815 if (host->caps.need_notbusy_for_read_ops ||
1816 (host->data->flags & MMC_DATA_WRITE)) {
1817 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1818 state = STATE_WAITING_NOTBUSY;
1819 } else if (host->mrq->stop) {
1820 atmci_writel(host, ATMCI_IER, ATMCI_CMDRDY);
1821 atmci_send_stop_cmd(host, data);
1822 state = STATE_SENDING_STOP;
1823 } else {
1824 host->data = NULL;
1825 data->bytes_xfered = data->blocks * data->blksz;
1826 data->error = 0;
1827 state = STATE_END_REQUEST;
1828 }
1829 break;
1830
1831 case STATE_WAITING_NOTBUSY:
1832 /*
1833 * We can be in the state for two reasons: a command
1834 * requiring waiting not busy signal (stop command
1835 * included) or a write operation. In the latest case,
1836 * we need to send a stop command.
1837 */
1838 dev_dbg(&host->pdev->dev, "FSM: not busy?\n");
1839 if (!atmci_test_and_clear_pending(host,
1840 EVENT_NOTBUSY))
1841 break;
1842
1843 dev_dbg(&host->pdev->dev, "set completed not busy\n");
1844 atmci_set_completed(host, EVENT_NOTBUSY);
1845
1846 if (host->data) {
1847 /*
1848 * For some commands such as CMD53, even if
1849 * there is data transfer, there is no stop
1850 * command to send.
1851 */
1852 if (host->mrq->stop) {
1853 atmci_writel(host, ATMCI_IER,
1854 ATMCI_CMDRDY);
1855 atmci_send_stop_cmd(host, data);
1856 state = STATE_SENDING_STOP;
1857 } else {
1858 host->data = NULL;
1859 data->bytes_xfered = data->blocks
1860 * data->blksz;
1861 data->error = 0;
1862 state = STATE_END_REQUEST;
1863 }
1864 } else
1865 state = STATE_END_REQUEST;
1866 break;
1867
1868 case STATE_SENDING_STOP:
1869 /*
1870 * In this state, it is important to set host->data to
1871 * NULL (which is tested in the waiting notbusy state)
1872 * in order to go to the end request state instead of
1873 * sending stop again.
1874 */
1875 dev_dbg(&host->pdev->dev, "FSM: cmd ready?\n");
1876 if (!atmci_test_and_clear_pending(host,
1877 EVENT_CMD_RDY))
1878 break;
1879
1880 dev_dbg(&host->pdev->dev, "FSM: cmd ready\n");
1881 host->cmd = NULL;
1882 data->bytes_xfered = data->blocks * data->blksz;
1883 data->error = 0;
1884 atmci_command_complete(host, mrq->stop);
1885 if (mrq->stop->error) {
1886 host->stop_transfer(host);
1887 atmci_writel(host, ATMCI_IDR,
1888 ATMCI_TXRDY | ATMCI_RXRDY
1889 | ATMCI_DATA_ERROR_FLAGS);
1890 state = STATE_END_REQUEST;
1891 } else {
1892 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1893 state = STATE_WAITING_NOTBUSY;
1894 }
1895 host->data = NULL;
1896 break;
1897
1898 case STATE_END_REQUEST:
1899 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY | ATMCI_RXRDY
1900 | ATMCI_DATA_ERROR_FLAGS);
1901 status = host->data_status;
1902 if (unlikely(status)) {
1903 host->stop_transfer(host);
1904 host->data = NULL;
1905 if (data) {
1906 if (status & ATMCI_DTOE) {
1907 data->error = -ETIMEDOUT;
1908 } else if (status & ATMCI_DCRCE) {
1909 data->error = -EILSEQ;
1910 } else {
1911 data->error = -EIO;
1912 }
1913 }
1914 }
1915
1916 atmci_request_end(host, host->mrq);
1917 goto unlock; /* atmci_request_end() sets host->state */
1918 break;
1919 }
1920 } while (state != prev_state);
1921
1922 host->state = state;
1923
1924 unlock:
1925 spin_unlock(&host->lock);
1926 }
1927
atmci_read_data_pio(struct atmel_mci * host)1928 static void atmci_read_data_pio(struct atmel_mci *host)
1929 {
1930 struct scatterlist *sg = host->sg;
1931 unsigned int offset = host->pio_offset;
1932 struct mmc_data *data = host->data;
1933 u32 value;
1934 u32 status;
1935 unsigned int nbytes = 0;
1936
1937 do {
1938 value = atmci_readl(host, ATMCI_RDR);
1939 if (likely(offset + 4 <= sg->length)) {
1940 sg_pcopy_from_buffer(sg, 1, &value, sizeof(u32), offset);
1941
1942 offset += 4;
1943 nbytes += 4;
1944
1945 if (offset == sg->length) {
1946 flush_dcache_page(sg_page(sg));
1947 host->sg = sg = sg_next(sg);
1948 host->sg_len--;
1949 if (!sg || !host->sg_len)
1950 goto done;
1951
1952 offset = 0;
1953 }
1954 } else {
1955 unsigned int remaining = sg->length - offset;
1956
1957 sg_pcopy_from_buffer(sg, 1, &value, remaining, offset);
1958 nbytes += remaining;
1959
1960 flush_dcache_page(sg_page(sg));
1961 host->sg = sg = sg_next(sg);
1962 host->sg_len--;
1963 if (!sg || !host->sg_len)
1964 goto done;
1965
1966 offset = 4 - remaining;
1967 sg_pcopy_from_buffer(sg, 1, (u8 *)&value + remaining,
1968 offset, 0);
1969 nbytes += offset;
1970 }
1971
1972 status = atmci_readl(host, ATMCI_SR);
1973 if (status & ATMCI_DATA_ERROR_FLAGS) {
1974 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_RXRDY
1975 | ATMCI_DATA_ERROR_FLAGS));
1976 host->data_status = status;
1977 data->bytes_xfered += nbytes;
1978 return;
1979 }
1980 } while (status & ATMCI_RXRDY);
1981
1982 host->pio_offset = offset;
1983 data->bytes_xfered += nbytes;
1984
1985 return;
1986
1987 done:
1988 atmci_writel(host, ATMCI_IDR, ATMCI_RXRDY);
1989 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
1990 data->bytes_xfered += nbytes;
1991 smp_wmb();
1992 atmci_set_pending(host, EVENT_XFER_COMPLETE);
1993 }
1994
atmci_write_data_pio(struct atmel_mci * host)1995 static void atmci_write_data_pio(struct atmel_mci *host)
1996 {
1997 struct scatterlist *sg = host->sg;
1998 unsigned int offset = host->pio_offset;
1999 struct mmc_data *data = host->data;
2000 u32 value;
2001 u32 status;
2002 unsigned int nbytes = 0;
2003
2004 do {
2005 if (likely(offset + 4 <= sg->length)) {
2006 sg_pcopy_to_buffer(sg, 1, &value, sizeof(u32), offset);
2007 atmci_writel(host, ATMCI_TDR, value);
2008
2009 offset += 4;
2010 nbytes += 4;
2011 if (offset == sg->length) {
2012 host->sg = sg = sg_next(sg);
2013 host->sg_len--;
2014 if (!sg || !host->sg_len)
2015 goto done;
2016
2017 offset = 0;
2018 }
2019 } else {
2020 unsigned int remaining = sg->length - offset;
2021
2022 value = 0;
2023 sg_pcopy_to_buffer(sg, 1, &value, remaining, offset);
2024 nbytes += remaining;
2025
2026 host->sg = sg = sg_next(sg);
2027 host->sg_len--;
2028 if (!sg || !host->sg_len) {
2029 atmci_writel(host, ATMCI_TDR, value);
2030 goto done;
2031 }
2032
2033 offset = 4 - remaining;
2034 sg_pcopy_to_buffer(sg, 1, (u8 *)&value + remaining,
2035 offset, 0);
2036 atmci_writel(host, ATMCI_TDR, value);
2037 nbytes += offset;
2038 }
2039
2040 status = atmci_readl(host, ATMCI_SR);
2041 if (status & ATMCI_DATA_ERROR_FLAGS) {
2042 atmci_writel(host, ATMCI_IDR, (ATMCI_NOTBUSY | ATMCI_TXRDY
2043 | ATMCI_DATA_ERROR_FLAGS));
2044 host->data_status = status;
2045 data->bytes_xfered += nbytes;
2046 return;
2047 }
2048 } while (status & ATMCI_TXRDY);
2049
2050 host->pio_offset = offset;
2051 data->bytes_xfered += nbytes;
2052
2053 return;
2054
2055 done:
2056 atmci_writel(host, ATMCI_IDR, ATMCI_TXRDY);
2057 atmci_writel(host, ATMCI_IER, ATMCI_NOTBUSY);
2058 data->bytes_xfered += nbytes;
2059 smp_wmb();
2060 atmci_set_pending(host, EVENT_XFER_COMPLETE);
2061 }
2062
atmci_sdio_interrupt(struct atmel_mci * host,u32 status)2063 static void atmci_sdio_interrupt(struct atmel_mci *host, u32 status)
2064 {
2065 int i;
2066
2067 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2068 struct atmel_mci_slot *slot = host->slot[i];
2069 if (slot && (status & slot->sdio_irq)) {
2070 mmc_signal_sdio_irq(slot->mmc);
2071 }
2072 }
2073 }
2074
2075
atmci_interrupt(int irq,void * dev_id)2076 static irqreturn_t atmci_interrupt(int irq, void *dev_id)
2077 {
2078 struct atmel_mci *host = dev_id;
2079 u32 status, mask, pending;
2080 unsigned int pass_count = 0;
2081
2082 do {
2083 status = atmci_readl(host, ATMCI_SR);
2084 mask = atmci_readl(host, ATMCI_IMR);
2085 pending = status & mask;
2086 if (!pending)
2087 break;
2088
2089 if (pending & ATMCI_DATA_ERROR_FLAGS) {
2090 dev_dbg(&host->pdev->dev, "IRQ: data error\n");
2091 atmci_writel(host, ATMCI_IDR, ATMCI_DATA_ERROR_FLAGS
2092 | ATMCI_RXRDY | ATMCI_TXRDY
2093 | ATMCI_ENDRX | ATMCI_ENDTX
2094 | ATMCI_RXBUFF | ATMCI_TXBUFE);
2095
2096 host->data_status = status;
2097 dev_dbg(&host->pdev->dev, "set pending data error\n");
2098 smp_wmb();
2099 atmci_set_pending(host, EVENT_DATA_ERROR);
2100 tasklet_schedule(&host->tasklet);
2101 }
2102
2103 if (pending & ATMCI_TXBUFE) {
2104 dev_dbg(&host->pdev->dev, "IRQ: tx buffer empty\n");
2105 atmci_writel(host, ATMCI_IDR, ATMCI_TXBUFE);
2106 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2107 /*
2108 * We can receive this interruption before having configured
2109 * the second pdc buffer, so we need to reconfigure first and
2110 * second buffers again
2111 */
2112 if (host->data_size) {
2113 atmci_pdc_set_both_buf(host, XFER_TRANSMIT);
2114 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2115 atmci_writel(host, ATMCI_IER, ATMCI_TXBUFE);
2116 } else {
2117 atmci_pdc_complete(host);
2118 }
2119 } else if (pending & ATMCI_ENDTX) {
2120 dev_dbg(&host->pdev->dev, "IRQ: end of tx buffer\n");
2121 atmci_writel(host, ATMCI_IDR, ATMCI_ENDTX);
2122
2123 if (host->data_size) {
2124 atmci_pdc_set_single_buf(host,
2125 XFER_TRANSMIT, PDC_SECOND_BUF);
2126 atmci_writel(host, ATMCI_IER, ATMCI_ENDTX);
2127 }
2128 }
2129
2130 if (pending & ATMCI_RXBUFF) {
2131 dev_dbg(&host->pdev->dev, "IRQ: rx buffer full\n");
2132 atmci_writel(host, ATMCI_IDR, ATMCI_RXBUFF);
2133 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2134 /*
2135 * We can receive this interruption before having configured
2136 * the second pdc buffer, so we need to reconfigure first and
2137 * second buffers again
2138 */
2139 if (host->data_size) {
2140 atmci_pdc_set_both_buf(host, XFER_RECEIVE);
2141 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2142 atmci_writel(host, ATMCI_IER, ATMCI_RXBUFF);
2143 } else {
2144 atmci_pdc_complete(host);
2145 }
2146 } else if (pending & ATMCI_ENDRX) {
2147 dev_dbg(&host->pdev->dev, "IRQ: end of rx buffer\n");
2148 atmci_writel(host, ATMCI_IDR, ATMCI_ENDRX);
2149
2150 if (host->data_size) {
2151 atmci_pdc_set_single_buf(host,
2152 XFER_RECEIVE, PDC_SECOND_BUF);
2153 atmci_writel(host, ATMCI_IER, ATMCI_ENDRX);
2154 }
2155 }
2156
2157 /*
2158 * First mci IPs, so mainly the ones having pdc, have some
2159 * issues with the notbusy signal. You can't get it after
2160 * data transmission if you have not sent a stop command.
2161 * The appropriate workaround is to use the BLKE signal.
2162 */
2163 if (pending & ATMCI_BLKE) {
2164 dev_dbg(&host->pdev->dev, "IRQ: blke\n");
2165 atmci_writel(host, ATMCI_IDR, ATMCI_BLKE);
2166 smp_wmb();
2167 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2168 atmci_set_pending(host, EVENT_NOTBUSY);
2169 tasklet_schedule(&host->tasklet);
2170 }
2171
2172 if (pending & ATMCI_NOTBUSY) {
2173 dev_dbg(&host->pdev->dev, "IRQ: not_busy\n");
2174 atmci_writel(host, ATMCI_IDR, ATMCI_NOTBUSY);
2175 smp_wmb();
2176 dev_dbg(&host->pdev->dev, "set pending notbusy\n");
2177 atmci_set_pending(host, EVENT_NOTBUSY);
2178 tasklet_schedule(&host->tasklet);
2179 }
2180
2181 if (pending & ATMCI_RXRDY)
2182 atmci_read_data_pio(host);
2183 if (pending & ATMCI_TXRDY)
2184 atmci_write_data_pio(host);
2185
2186 if (pending & ATMCI_CMDRDY) {
2187 dev_dbg(&host->pdev->dev, "IRQ: cmd ready\n");
2188 atmci_writel(host, ATMCI_IDR, ATMCI_CMDRDY);
2189 host->cmd_status = status;
2190 smp_wmb();
2191 dev_dbg(&host->pdev->dev, "set pending cmd rdy\n");
2192 atmci_set_pending(host, EVENT_CMD_RDY);
2193 tasklet_schedule(&host->tasklet);
2194 }
2195
2196 if (pending & (ATMCI_SDIOIRQA | ATMCI_SDIOIRQB))
2197 atmci_sdio_interrupt(host, status);
2198
2199 } while (pass_count++ < 5);
2200
2201 return pass_count ? IRQ_HANDLED : IRQ_NONE;
2202 }
2203
atmci_detect_interrupt(int irq,void * dev_id)2204 static irqreturn_t atmci_detect_interrupt(int irq, void *dev_id)
2205 {
2206 struct atmel_mci_slot *slot = dev_id;
2207
2208 /*
2209 * Disable interrupts until the pin has stabilized and check
2210 * the state then. Use mod_timer() since we may be in the
2211 * middle of the timer routine when this interrupt triggers.
2212 */
2213 disable_irq_nosync(irq);
2214 mod_timer(&slot->detect_timer, jiffies + msecs_to_jiffies(20));
2215
2216 return IRQ_HANDLED;
2217 }
2218
atmci_init_slot(struct atmel_mci * host,struct mci_slot_pdata * slot_data,unsigned int id,u32 sdc_reg,u32 sdio_irq)2219 static int atmci_init_slot(struct atmel_mci *host,
2220 struct mci_slot_pdata *slot_data, unsigned int id,
2221 u32 sdc_reg, u32 sdio_irq)
2222 {
2223 struct mmc_host *mmc;
2224 struct atmel_mci_slot *slot;
2225
2226 mmc = mmc_alloc_host(sizeof(struct atmel_mci_slot), &host->pdev->dev);
2227 if (!mmc)
2228 return -ENOMEM;
2229
2230 slot = mmc_priv(mmc);
2231 slot->mmc = mmc;
2232 slot->host = host;
2233 slot->detect_pin = slot_data->detect_pin;
2234 slot->wp_pin = slot_data->wp_pin;
2235 slot->detect_is_active_high = slot_data->detect_is_active_high;
2236 slot->sdc_reg = sdc_reg;
2237 slot->sdio_irq = sdio_irq;
2238
2239 dev_dbg(&mmc->class_dev,
2240 "slot[%u]: bus_width=%u, detect_pin=%d, "
2241 "detect_is_active_high=%s, wp_pin=%d\n",
2242 id, slot_data->bus_width, slot_data->detect_pin,
2243 slot_data->detect_is_active_high ? "true" : "false",
2244 slot_data->wp_pin);
2245
2246 mmc->ops = &atmci_ops;
2247 mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
2248 mmc->f_max = host->bus_hz / 2;
2249 mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
2250 if (sdio_irq)
2251 mmc->caps |= MMC_CAP_SDIO_IRQ;
2252 if (host->caps.has_highspeed)
2253 mmc->caps |= MMC_CAP_SD_HIGHSPEED;
2254 /*
2255 * Without the read/write proof capability, it is strongly suggested to
2256 * use only one bit for data to prevent fifo underruns and overruns
2257 * which will corrupt data.
2258 */
2259 if ((slot_data->bus_width >= 4) && host->caps.has_rwproof) {
2260 mmc->caps |= MMC_CAP_4_BIT_DATA;
2261 if (slot_data->bus_width >= 8)
2262 mmc->caps |= MMC_CAP_8_BIT_DATA;
2263 }
2264
2265 if (atmci_get_version(host) < 0x200) {
2266 mmc->max_segs = 256;
2267 mmc->max_blk_size = 4095;
2268 mmc->max_blk_count = 256;
2269 mmc->max_req_size = mmc->max_blk_size * mmc->max_blk_count;
2270 mmc->max_seg_size = mmc->max_blk_size * mmc->max_segs;
2271 } else {
2272 mmc->max_segs = 64;
2273 mmc->max_req_size = 32768 * 512;
2274 mmc->max_blk_size = 32768;
2275 mmc->max_blk_count = 512;
2276 }
2277
2278 /* Assume card is present initially */
2279 set_bit(ATMCI_CARD_PRESENT, &slot->flags);
2280 if (gpio_is_valid(slot->detect_pin)) {
2281 if (devm_gpio_request(&host->pdev->dev, slot->detect_pin,
2282 "mmc_detect")) {
2283 dev_dbg(&mmc->class_dev, "no detect pin available\n");
2284 slot->detect_pin = -EBUSY;
2285 } else if (gpio_get_value(slot->detect_pin) ^
2286 slot->detect_is_active_high) {
2287 clear_bit(ATMCI_CARD_PRESENT, &slot->flags);
2288 }
2289 }
2290
2291 if (!gpio_is_valid(slot->detect_pin)) {
2292 if (slot_data->non_removable)
2293 mmc->caps |= MMC_CAP_NONREMOVABLE;
2294 else
2295 mmc->caps |= MMC_CAP_NEEDS_POLL;
2296 }
2297
2298 if (gpio_is_valid(slot->wp_pin)) {
2299 if (devm_gpio_request(&host->pdev->dev, slot->wp_pin,
2300 "mmc_wp")) {
2301 dev_dbg(&mmc->class_dev, "no WP pin available\n");
2302 slot->wp_pin = -EBUSY;
2303 }
2304 }
2305
2306 host->slot[id] = slot;
2307 mmc_regulator_get_supply(mmc);
2308 mmc_add_host(mmc);
2309
2310 if (gpio_is_valid(slot->detect_pin)) {
2311 int ret;
2312
2313 timer_setup(&slot->detect_timer, atmci_detect_change, 0);
2314
2315 ret = request_irq(gpio_to_irq(slot->detect_pin),
2316 atmci_detect_interrupt,
2317 IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
2318 "mmc-detect", slot);
2319 if (ret) {
2320 dev_dbg(&mmc->class_dev,
2321 "could not request IRQ %d for detect pin\n",
2322 gpio_to_irq(slot->detect_pin));
2323 slot->detect_pin = -EBUSY;
2324 }
2325 }
2326
2327 atmci_init_debugfs(slot);
2328
2329 return 0;
2330 }
2331
atmci_cleanup_slot(struct atmel_mci_slot * slot,unsigned int id)2332 static void atmci_cleanup_slot(struct atmel_mci_slot *slot,
2333 unsigned int id)
2334 {
2335 /* Debugfs stuff is cleaned up by mmc core */
2336
2337 set_bit(ATMCI_SHUTDOWN, &slot->flags);
2338 smp_wmb();
2339
2340 mmc_remove_host(slot->mmc);
2341
2342 if (gpio_is_valid(slot->detect_pin)) {
2343 int pin = slot->detect_pin;
2344
2345 free_irq(gpio_to_irq(pin), slot);
2346 del_timer_sync(&slot->detect_timer);
2347 }
2348
2349 slot->host->slot[id] = NULL;
2350 mmc_free_host(slot->mmc);
2351 }
2352
atmci_configure_dma(struct atmel_mci * host)2353 static int atmci_configure_dma(struct atmel_mci *host)
2354 {
2355 host->dma.chan = dma_request_chan(&host->pdev->dev, "rxtx");
2356
2357 if (PTR_ERR(host->dma.chan) == -ENODEV) {
2358 struct mci_platform_data *pdata = host->pdev->dev.platform_data;
2359 dma_cap_mask_t mask;
2360
2361 if (!pdata || !pdata->dma_filter)
2362 return -ENODEV;
2363
2364 dma_cap_zero(mask);
2365 dma_cap_set(DMA_SLAVE, mask);
2366
2367 host->dma.chan = dma_request_channel(mask, pdata->dma_filter,
2368 pdata->dma_slave);
2369 if (!host->dma.chan)
2370 host->dma.chan = ERR_PTR(-ENODEV);
2371 }
2372
2373 if (IS_ERR(host->dma.chan))
2374 return PTR_ERR(host->dma.chan);
2375
2376 dev_info(&host->pdev->dev, "using %s for DMA transfers\n",
2377 dma_chan_name(host->dma.chan));
2378
2379 host->dma_conf.src_addr = host->mapbase + ATMCI_RDR;
2380 host->dma_conf.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2381 host->dma_conf.src_maxburst = 1;
2382 host->dma_conf.dst_addr = host->mapbase + ATMCI_TDR;
2383 host->dma_conf.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
2384 host->dma_conf.dst_maxburst = 1;
2385 host->dma_conf.device_fc = false;
2386
2387 return 0;
2388 }
2389
2390 /*
2391 * HSMCI (High Speed MCI) module is not fully compatible with MCI module.
2392 * HSMCI provides DMA support and a new config register but no more supports
2393 * PDC.
2394 */
atmci_get_cap(struct atmel_mci * host)2395 static void atmci_get_cap(struct atmel_mci *host)
2396 {
2397 unsigned int version;
2398
2399 version = atmci_get_version(host);
2400 dev_info(&host->pdev->dev,
2401 "version: 0x%x\n", version);
2402
2403 host->caps.has_dma_conf_reg = false;
2404 host->caps.has_pdc = true;
2405 host->caps.has_cfg_reg = false;
2406 host->caps.has_cstor_reg = false;
2407 host->caps.has_highspeed = false;
2408 host->caps.has_rwproof = false;
2409 host->caps.has_odd_clk_div = false;
2410 host->caps.has_bad_data_ordering = true;
2411 host->caps.need_reset_after_xfer = true;
2412 host->caps.need_blksz_mul_4 = true;
2413 host->caps.need_notbusy_for_read_ops = false;
2414
2415 /* keep only major version number */
2416 switch (version & 0xf00) {
2417 case 0x600:
2418 case 0x500:
2419 host->caps.has_odd_clk_div = true;
2420 fallthrough;
2421 case 0x400:
2422 case 0x300:
2423 host->caps.has_dma_conf_reg = true;
2424 host->caps.has_pdc = false;
2425 host->caps.has_cfg_reg = true;
2426 host->caps.has_cstor_reg = true;
2427 host->caps.has_highspeed = true;
2428 fallthrough;
2429 case 0x200:
2430 host->caps.has_rwproof = true;
2431 host->caps.need_blksz_mul_4 = false;
2432 host->caps.need_notbusy_for_read_ops = true;
2433 fallthrough;
2434 case 0x100:
2435 host->caps.has_bad_data_ordering = false;
2436 host->caps.need_reset_after_xfer = false;
2437 fallthrough;
2438 case 0x0:
2439 break;
2440 default:
2441 host->caps.has_pdc = false;
2442 dev_warn(&host->pdev->dev,
2443 "Unmanaged mci version, set minimum capabilities\n");
2444 break;
2445 }
2446 }
2447
atmci_probe(struct platform_device * pdev)2448 static int atmci_probe(struct platform_device *pdev)
2449 {
2450 struct mci_platform_data *pdata;
2451 struct atmel_mci *host;
2452 struct resource *regs;
2453 unsigned int nr_slots;
2454 int irq;
2455 int ret, i;
2456
2457 regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2458 if (!regs)
2459 return -ENXIO;
2460 pdata = pdev->dev.platform_data;
2461 if (!pdata) {
2462 pdata = atmci_of_init(pdev);
2463 if (IS_ERR(pdata)) {
2464 dev_err(&pdev->dev, "platform data not available\n");
2465 return PTR_ERR(pdata);
2466 }
2467 }
2468
2469 irq = platform_get_irq(pdev, 0);
2470 if (irq < 0)
2471 return irq;
2472
2473 host = devm_kzalloc(&pdev->dev, sizeof(*host), GFP_KERNEL);
2474 if (!host)
2475 return -ENOMEM;
2476
2477 host->pdev = pdev;
2478 spin_lock_init(&host->lock);
2479 INIT_LIST_HEAD(&host->queue);
2480
2481 host->mck = devm_clk_get(&pdev->dev, "mci_clk");
2482 if (IS_ERR(host->mck))
2483 return PTR_ERR(host->mck);
2484
2485 host->regs = devm_ioremap(&pdev->dev, regs->start, resource_size(regs));
2486 if (!host->regs)
2487 return -ENOMEM;
2488
2489 ret = clk_prepare_enable(host->mck);
2490 if (ret)
2491 return ret;
2492
2493 atmci_writel(host, ATMCI_CR, ATMCI_CR_SWRST);
2494 host->bus_hz = clk_get_rate(host->mck);
2495
2496 host->mapbase = regs->start;
2497
2498 tasklet_setup(&host->tasklet, atmci_tasklet_func);
2499
2500 ret = request_irq(irq, atmci_interrupt, 0, dev_name(&pdev->dev), host);
2501 if (ret) {
2502 clk_disable_unprepare(host->mck);
2503 return ret;
2504 }
2505
2506 /* Get MCI capabilities and set operations according to it */
2507 atmci_get_cap(host);
2508 ret = atmci_configure_dma(host);
2509 if (ret == -EPROBE_DEFER)
2510 goto err_dma_probe_defer;
2511 if (ret == 0) {
2512 host->prepare_data = &atmci_prepare_data_dma;
2513 host->submit_data = &atmci_submit_data_dma;
2514 host->stop_transfer = &atmci_stop_transfer_dma;
2515 } else if (host->caps.has_pdc) {
2516 dev_info(&pdev->dev, "using PDC\n");
2517 host->prepare_data = &atmci_prepare_data_pdc;
2518 host->submit_data = &atmci_submit_data_pdc;
2519 host->stop_transfer = &atmci_stop_transfer_pdc;
2520 } else {
2521 dev_info(&pdev->dev, "using PIO\n");
2522 host->prepare_data = &atmci_prepare_data;
2523 host->submit_data = &atmci_submit_data;
2524 host->stop_transfer = &atmci_stop_transfer;
2525 }
2526
2527 platform_set_drvdata(pdev, host);
2528
2529 timer_setup(&host->timer, atmci_timeout_timer, 0);
2530
2531 pm_runtime_get_noresume(&pdev->dev);
2532 pm_runtime_set_active(&pdev->dev);
2533 pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_DELAY);
2534 pm_runtime_use_autosuspend(&pdev->dev);
2535 pm_runtime_enable(&pdev->dev);
2536
2537 /* We need at least one slot to succeed */
2538 nr_slots = 0;
2539 ret = -ENODEV;
2540 if (pdata->slot[0].bus_width) {
2541 ret = atmci_init_slot(host, &pdata->slot[0],
2542 0, ATMCI_SDCSEL_SLOT_A, ATMCI_SDIOIRQA);
2543 if (!ret) {
2544 nr_slots++;
2545 host->buf_size = host->slot[0]->mmc->max_req_size;
2546 }
2547 }
2548 if (pdata->slot[1].bus_width) {
2549 ret = atmci_init_slot(host, &pdata->slot[1],
2550 1, ATMCI_SDCSEL_SLOT_B, ATMCI_SDIOIRQB);
2551 if (!ret) {
2552 nr_slots++;
2553 if (host->slot[1]->mmc->max_req_size > host->buf_size)
2554 host->buf_size =
2555 host->slot[1]->mmc->max_req_size;
2556 }
2557 }
2558
2559 if (!nr_slots) {
2560 dev_err(&pdev->dev, "init failed: no slot defined\n");
2561 goto err_init_slot;
2562 }
2563
2564 if (!host->caps.has_rwproof) {
2565 host->buffer = dma_alloc_coherent(&pdev->dev, host->buf_size,
2566 &host->buf_phys_addr,
2567 GFP_KERNEL);
2568 if (!host->buffer) {
2569 ret = -ENOMEM;
2570 dev_err(&pdev->dev, "buffer allocation failed\n");
2571 goto err_dma_alloc;
2572 }
2573 }
2574
2575 dev_info(&pdev->dev,
2576 "Atmel MCI controller at 0x%08lx irq %d, %u slots\n",
2577 host->mapbase, irq, nr_slots);
2578
2579 pm_runtime_mark_last_busy(&host->pdev->dev);
2580 pm_runtime_put_autosuspend(&pdev->dev);
2581
2582 return 0;
2583
2584 err_dma_alloc:
2585 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2586 if (host->slot[i])
2587 atmci_cleanup_slot(host->slot[i], i);
2588 }
2589 err_init_slot:
2590 clk_disable_unprepare(host->mck);
2591
2592 pm_runtime_disable(&pdev->dev);
2593 pm_runtime_put_noidle(&pdev->dev);
2594
2595 del_timer_sync(&host->timer);
2596 if (!IS_ERR(host->dma.chan))
2597 dma_release_channel(host->dma.chan);
2598 err_dma_probe_defer:
2599 free_irq(irq, host);
2600 return ret;
2601 }
2602
atmci_remove(struct platform_device * pdev)2603 static int atmci_remove(struct platform_device *pdev)
2604 {
2605 struct atmel_mci *host = platform_get_drvdata(pdev);
2606 unsigned int i;
2607
2608 pm_runtime_get_sync(&pdev->dev);
2609
2610 if (host->buffer)
2611 dma_free_coherent(&pdev->dev, host->buf_size,
2612 host->buffer, host->buf_phys_addr);
2613
2614 for (i = 0; i < ATMCI_MAX_NR_SLOTS; i++) {
2615 if (host->slot[i])
2616 atmci_cleanup_slot(host->slot[i], i);
2617 }
2618
2619 atmci_writel(host, ATMCI_IDR, ~0UL);
2620 atmci_writel(host, ATMCI_CR, ATMCI_CR_MCIDIS);
2621 atmci_readl(host, ATMCI_SR);
2622
2623 del_timer_sync(&host->timer);
2624 if (!IS_ERR(host->dma.chan))
2625 dma_release_channel(host->dma.chan);
2626
2627 free_irq(platform_get_irq(pdev, 0), host);
2628
2629 clk_disable_unprepare(host->mck);
2630
2631 pm_runtime_disable(&pdev->dev);
2632 pm_runtime_put_noidle(&pdev->dev);
2633
2634 return 0;
2635 }
2636
2637 #ifdef CONFIG_PM
atmci_runtime_suspend(struct device * dev)2638 static int atmci_runtime_suspend(struct device *dev)
2639 {
2640 struct atmel_mci *host = dev_get_drvdata(dev);
2641
2642 clk_disable_unprepare(host->mck);
2643
2644 pinctrl_pm_select_sleep_state(dev);
2645
2646 return 0;
2647 }
2648
atmci_runtime_resume(struct device * dev)2649 static int atmci_runtime_resume(struct device *dev)
2650 {
2651 struct atmel_mci *host = dev_get_drvdata(dev);
2652
2653 pinctrl_select_default_state(dev);
2654
2655 return clk_prepare_enable(host->mck);
2656 }
2657 #endif
2658
2659 static const struct dev_pm_ops atmci_dev_pm_ops = {
2660 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
2661 pm_runtime_force_resume)
2662 SET_RUNTIME_PM_OPS(atmci_runtime_suspend, atmci_runtime_resume, NULL)
2663 };
2664
2665 static struct platform_driver atmci_driver = {
2666 .probe = atmci_probe,
2667 .remove = atmci_remove,
2668 .driver = {
2669 .name = "atmel_mci",
2670 .probe_type = PROBE_PREFER_ASYNCHRONOUS,
2671 .of_match_table = of_match_ptr(atmci_dt_ids),
2672 .pm = &atmci_dev_pm_ops,
2673 },
2674 };
2675 module_platform_driver(atmci_driver);
2676
2677 MODULE_DESCRIPTION("Atmel Multimedia Card Interface driver");
2678 MODULE_AUTHOR("Haavard Skinnemoen (Atmel)");
2679 MODULE_LICENSE("GPL v2");
2680