1 /* 2 * Blackfin On-Chip SPI Driver 3 * 4 * Copyright 2004-2008 Analog Devices Inc. 5 * 6 * Licensed under the GPL-2 or later. 7 */ 8 9 #ifndef _SPI_CHANNEL_H_ 10 #define _SPI_CHANNEL_H_ 11 12 #define MIN_SPI_BAUD_VAL 2 13 14 #define BIT_CTL_ENABLE 0x4000 15 #define BIT_CTL_OPENDRAIN 0x2000 16 #define BIT_CTL_MASTER 0x1000 17 #define BIT_CTL_CPOL 0x0800 18 #define BIT_CTL_CPHA 0x0400 19 #define BIT_CTL_LSBF 0x0200 20 #define BIT_CTL_WORDSIZE 0x0100 21 #define BIT_CTL_EMISO 0x0020 22 #define BIT_CTL_PSSE 0x0010 23 #define BIT_CTL_GM 0x0008 24 #define BIT_CTL_SZ 0x0004 25 #define BIT_CTL_RXMOD 0x0000 26 #define BIT_CTL_TXMOD 0x0001 27 #define BIT_CTL_TIMOD_DMA_TX 0x0003 28 #define BIT_CTL_TIMOD_DMA_RX 0x0002 29 #define BIT_CTL_SENDOPT 0x0004 30 #define BIT_CTL_TIMOD 0x0003 31 32 #define BIT_STAT_SPIF 0x0001 33 #define BIT_STAT_MODF 0x0002 34 #define BIT_STAT_TXE 0x0004 35 #define BIT_STAT_TXS 0x0008 36 #define BIT_STAT_RBSY 0x0010 37 #define BIT_STAT_RXS 0x0020 38 #define BIT_STAT_TXCOL 0x0040 39 #define BIT_STAT_CLR 0xFFFF 40 41 #define BIT_STU_SENDOVER 0x0001 42 #define BIT_STU_RECVFULL 0x0020 43 44 /* 45 * All Blackfin system MMRs are padded to 32bits even if the register 46 * itself is only 16bits. So use a helper macro to streamline this. 47 */ 48 #define __BFP(m) u16 m; u16 __pad_##m 49 50 /* 51 * bfin spi registers layout 52 */ 53 struct bfin_spi_regs { 54 __BFP(ctl); 55 __BFP(flg); 56 __BFP(stat); 57 __BFP(tdbr); 58 __BFP(rdbr); 59 __BFP(baud); 60 __BFP(shadow); 61 }; 62 63 #undef __BFP 64 65 #define MAX_CTRL_CS 8 /* cs in spi controller */ 66 67 /* device.platform_data for SSP controller devices */ 68 struct bfin5xx_spi_master { 69 u16 num_chipselect; 70 u8 enable_dma; 71 u16 pin_req[7]; 72 }; 73 74 /* spi_board_info.controller_data for SPI slave devices, 75 * copied to spi_device.platform_data ... mostly for dma tuning 76 */ 77 struct bfin5xx_spi_chip { 78 u16 ctl_reg; 79 u8 enable_dma; 80 u8 bits_per_word; 81 u16 cs_chg_udelay; /* Some devices require 16-bit delays */ 82 /* Value to send if no TX value is supplied, usually 0x0 or 0xFFFF */ 83 u16 idle_tx_val; 84 u8 pio_interrupt; /* Enable spi data irq */ 85 }; 86 87 #endif /* _SPI_CHANNEL_H_ */ 88