1 /* 2 * opp2xxx.h - macros for old-style OMAP2xxx "OPP" definitions 3 * 4 * Copyright (C) 2005-2009 Texas Instruments, Inc. 5 * Copyright (C) 2004-2009 Nokia Corporation 6 * 7 * Richard Woodruff <r-woodruff2@ti.com> 8 * 9 * The OMAP2 processor can be run at several discrete 'PRCM configurations'. 10 * These configurations are characterized by voltage and speed for clocks. 11 * The device is only validated for certain combinations. One way to express 12 * these combinations is via the 'ratio's' which the clocks operate with 13 * respect to each other. These ratio sets are for a given voltage/DPLL 14 * setting. All configurations can be described by a DPLL setting and a ratio 15 * There are 3 ratio sets for the 2430 and X ratio sets for 2420. 16 * 17 * 2430 differs from 2420 in that there are no more phase synchronizers used. 18 * They both have a slightly different clock domain setup. 2420(iva1,dsp) vs 19 * 2430 (iva2.1, NOdsp, mdm) 20 * 21 * XXX Missing voltage data. 22 * 23 * THe format described in this file is deprecated. Once a reasonable 24 * OPP API exists, the data in this file should be converted to use it. 25 * 26 * This is technically part of the OMAP2xxx clock code. 27 */ 28 29 #ifndef __ARCH_ARM_MACH_OMAP2_OPP2XXX_H 30 #define __ARCH_ARM_MACH_OMAP2_OPP2XXX_H 31 32 /** 33 * struct prcm_config - define clock rates on a per-OPP basis (24xx) 34 * 35 * Key dividers which make up a PRCM set. Ratio's for a PRCM are mandated. 36 * xtal_speed, dpll_speed, mpu_speed, CM_CLKSEL_MPU,CM_CLKSEL_DSP 37 * CM_CLKSEL_GFX, CM_CLKSEL1_CORE, CM_CLKSEL1_PLL CM_CLKSEL2_PLL, CM_CLKSEL_MDM 38 * 39 * This is deprecated. As soon as we have a decent OPP API, we should 40 * move all this stuff to it. 41 */ 42 struct prcm_config { 43 unsigned long xtal_speed; /* crystal rate */ 44 unsigned long dpll_speed; /* dpll: out*xtal*M/(N-1)table_recalc */ 45 unsigned long mpu_speed; /* speed of MPU */ 46 unsigned long cm_clksel_mpu; /* mpu divider */ 47 unsigned long cm_clksel_dsp; /* dsp+iva1 div(2420), iva2.1(2430) */ 48 unsigned long cm_clksel_gfx; /* gfx dividers */ 49 unsigned long cm_clksel1_core; /* major subsystem dividers */ 50 unsigned long cm_clksel1_pll; /* m,n */ 51 unsigned long cm_clksel2_pll; /* dpllx1 or x2 out */ 52 unsigned long cm_clksel_mdm; /* modem dividers 2430 only */ 53 unsigned long base_sdrc_rfr; /* base refresh timing for a set */ 54 unsigned char flags; 55 }; 56 57 58 /* Core fields for cm_clksel, not ratio governed */ 59 #define RX_CLKSEL_DSS1 (0x10 << 8) 60 #define RX_CLKSEL_DSS2 (0x0 << 13) 61 #define RX_CLKSEL_SSI (0x5 << 20) 62 63 /*------------------------------------------------------------------------- 64 * Voltage/DPLL ratios 65 *-------------------------------------------------------------------------*/ 66 67 /* 2430 Ratio's, 2430-Ratio Config 1 */ 68 #define R1_CLKSEL_L3 (4 << 0) 69 #define R1_CLKSEL_L4 (2 << 5) 70 #define R1_CLKSEL_USB (4 << 25) 71 #define R1_CM_CLKSEL1_CORE_VAL (R1_CLKSEL_USB | RX_CLKSEL_SSI | \ 72 RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ 73 R1_CLKSEL_L4 | R1_CLKSEL_L3) 74 #define R1_CLKSEL_MPU (2 << 0) 75 #define R1_CM_CLKSEL_MPU_VAL R1_CLKSEL_MPU 76 #define R1_CLKSEL_DSP (2 << 0) 77 #define R1_CLKSEL_DSP_IF (2 << 5) 78 #define R1_CM_CLKSEL_DSP_VAL (R1_CLKSEL_DSP | R1_CLKSEL_DSP_IF) 79 #define R1_CLKSEL_GFX (2 << 0) 80 #define R1_CM_CLKSEL_GFX_VAL R1_CLKSEL_GFX 81 #define R1_CLKSEL_MDM (4 << 0) 82 #define R1_CM_CLKSEL_MDM_VAL R1_CLKSEL_MDM 83 84 /* 2430-Ratio Config 2 */ 85 #define R2_CLKSEL_L3 (6 << 0) 86 #define R2_CLKSEL_L4 (2 << 5) 87 #define R2_CLKSEL_USB (2 << 25) 88 #define R2_CM_CLKSEL1_CORE_VAL (R2_CLKSEL_USB | RX_CLKSEL_SSI | \ 89 RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ 90 R2_CLKSEL_L4 | R2_CLKSEL_L3) 91 #define R2_CLKSEL_MPU (2 << 0) 92 #define R2_CM_CLKSEL_MPU_VAL R2_CLKSEL_MPU 93 #define R2_CLKSEL_DSP (2 << 0) 94 #define R2_CLKSEL_DSP_IF (3 << 5) 95 #define R2_CM_CLKSEL_DSP_VAL (R2_CLKSEL_DSP | R2_CLKSEL_DSP_IF) 96 #define R2_CLKSEL_GFX (2 << 0) 97 #define R2_CM_CLKSEL_GFX_VAL R2_CLKSEL_GFX 98 #define R2_CLKSEL_MDM (6 << 0) 99 #define R2_CM_CLKSEL_MDM_VAL R2_CLKSEL_MDM 100 101 /* 2430-Ratio Bootm (BYPASS) */ 102 #define RB_CLKSEL_L3 (1 << 0) 103 #define RB_CLKSEL_L4 (1 << 5) 104 #define RB_CLKSEL_USB (1 << 25) 105 #define RB_CM_CLKSEL1_CORE_VAL (RB_CLKSEL_USB | RX_CLKSEL_SSI | \ 106 RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ 107 RB_CLKSEL_L4 | RB_CLKSEL_L3) 108 #define RB_CLKSEL_MPU (1 << 0) 109 #define RB_CM_CLKSEL_MPU_VAL RB_CLKSEL_MPU 110 #define RB_CLKSEL_DSP (1 << 0) 111 #define RB_CLKSEL_DSP_IF (1 << 5) 112 #define RB_CM_CLKSEL_DSP_VAL (RB_CLKSEL_DSP | RB_CLKSEL_DSP_IF) 113 #define RB_CLKSEL_GFX (1 << 0) 114 #define RB_CM_CLKSEL_GFX_VAL RB_CLKSEL_GFX 115 #define RB_CLKSEL_MDM (1 << 0) 116 #define RB_CM_CLKSEL_MDM_VAL RB_CLKSEL_MDM 117 118 /* 2420 Ratio Equivalents */ 119 #define RXX_CLKSEL_VLYNQ (0x12 << 15) 120 #define RXX_CLKSEL_SSI (0x8 << 20) 121 122 /* 2420-PRCM III 532MHz core */ 123 #define RIII_CLKSEL_L3 (4 << 0) /* 133MHz */ 124 #define RIII_CLKSEL_L4 (2 << 5) /* 66.5MHz */ 125 #define RIII_CLKSEL_USB (4 << 25) /* 33.25MHz */ 126 #define RIII_CM_CLKSEL1_CORE_VAL (RIII_CLKSEL_USB | RXX_CLKSEL_SSI | \ 127 RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \ 128 RX_CLKSEL_DSS1 | RIII_CLKSEL_L4 | \ 129 RIII_CLKSEL_L3) 130 #define RIII_CLKSEL_MPU (2 << 0) /* 266MHz */ 131 #define RIII_CM_CLKSEL_MPU_VAL RIII_CLKSEL_MPU 132 #define RIII_CLKSEL_DSP (3 << 0) /* c5x - 177.3MHz */ 133 #define RIII_CLKSEL_DSP_IF (2 << 5) /* c5x - 88.67MHz */ 134 #define RIII_SYNC_DSP (1 << 7) /* Enable sync */ 135 #define RIII_CLKSEL_IVA (6 << 8) /* iva1 - 88.67MHz */ 136 #define RIII_SYNC_IVA (1 << 13) /* Enable sync */ 137 #define RIII_CM_CLKSEL_DSP_VAL (RIII_SYNC_IVA | RIII_CLKSEL_IVA | \ 138 RIII_SYNC_DSP | RIII_CLKSEL_DSP_IF | \ 139 RIII_CLKSEL_DSP) 140 #define RIII_CLKSEL_GFX (2 << 0) /* 66.5MHz */ 141 #define RIII_CM_CLKSEL_GFX_VAL RIII_CLKSEL_GFX 142 143 /* 2420-PRCM II 600MHz core */ 144 #define RII_CLKSEL_L3 (6 << 0) /* 100MHz */ 145 #define RII_CLKSEL_L4 (2 << 5) /* 50MHz */ 146 #define RII_CLKSEL_USB (2 << 25) /* 50MHz */ 147 #define RII_CM_CLKSEL1_CORE_VAL (RII_CLKSEL_USB | RXX_CLKSEL_SSI | \ 148 RXX_CLKSEL_VLYNQ | RX_CLKSEL_DSS2 | \ 149 RX_CLKSEL_DSS1 | RII_CLKSEL_L4 | \ 150 RII_CLKSEL_L3) 151 #define RII_CLKSEL_MPU (2 << 0) /* 300MHz */ 152 #define RII_CM_CLKSEL_MPU_VAL RII_CLKSEL_MPU 153 #define RII_CLKSEL_DSP (3 << 0) /* c5x - 200MHz */ 154 #define RII_CLKSEL_DSP_IF (2 << 5) /* c5x - 100MHz */ 155 #define RII_SYNC_DSP (0 << 7) /* Bypass sync */ 156 #define RII_CLKSEL_IVA (3 << 8) /* iva1 - 200MHz */ 157 #define RII_SYNC_IVA (0 << 13) /* Bypass sync */ 158 #define RII_CM_CLKSEL_DSP_VAL (RII_SYNC_IVA | RII_CLKSEL_IVA | \ 159 RII_SYNC_DSP | RII_CLKSEL_DSP_IF | \ 160 RII_CLKSEL_DSP) 161 #define RII_CLKSEL_GFX (2 << 0) /* 50MHz */ 162 #define RII_CM_CLKSEL_GFX_VAL RII_CLKSEL_GFX 163 164 /* 2420-PRCM I 660MHz core */ 165 #define RI_CLKSEL_L3 (4 << 0) /* 165MHz */ 166 #define RI_CLKSEL_L4 (2 << 5) /* 82.5MHz */ 167 #define RI_CLKSEL_USB (4 << 25) /* 41.25MHz */ 168 #define RI_CM_CLKSEL1_CORE_VAL (RI_CLKSEL_USB | \ 169 RXX_CLKSEL_SSI | RXX_CLKSEL_VLYNQ | \ 170 RX_CLKSEL_DSS2 | RX_CLKSEL_DSS1 | \ 171 RI_CLKSEL_L4 | RI_CLKSEL_L3) 172 #define RI_CLKSEL_MPU (2 << 0) /* 330MHz */ 173 #define RI_CM_CLKSEL_MPU_VAL RI_CLKSEL_MPU 174 #define RI_CLKSEL_DSP (3 << 0) /* c5x - 220MHz */ 175 #define RI_CLKSEL_DSP_IF (2 << 5) /* c5x - 110MHz */ 176 #define RI_SYNC_DSP (1 << 7) /* Activate sync */ 177 #define RI_CLKSEL_IVA (4 << 8) /* iva1 - 165MHz */ 178 #define RI_SYNC_IVA (0 << 13) /* Bypass sync */ 179 #define RI_CM_CLKSEL_DSP_VAL (RI_SYNC_IVA | RI_CLKSEL_IVA | \ 180 RI_SYNC_DSP | RI_CLKSEL_DSP_IF | \ 181 RI_CLKSEL_DSP) 182 #define RI_CLKSEL_GFX (1 << 0) /* 165MHz */ 183 #define RI_CM_CLKSEL_GFX_VAL RI_CLKSEL_GFX 184 185 /* 2420-PRCM VII (boot) */ 186 #define RVII_CLKSEL_L3 (1 << 0) 187 #define RVII_CLKSEL_L4 (1 << 5) 188 #define RVII_CLKSEL_DSS1 (1 << 8) 189 #define RVII_CLKSEL_DSS2 (0 << 13) 190 #define RVII_CLKSEL_VLYNQ (1 << 15) 191 #define RVII_CLKSEL_SSI (1 << 20) 192 #define RVII_CLKSEL_USB (1 << 25) 193 194 #define RVII_CM_CLKSEL1_CORE_VAL (RVII_CLKSEL_USB | RVII_CLKSEL_SSI | \ 195 RVII_CLKSEL_VLYNQ | \ 196 RVII_CLKSEL_DSS2 | RVII_CLKSEL_DSS1 | \ 197 RVII_CLKSEL_L4 | RVII_CLKSEL_L3) 198 199 #define RVII_CLKSEL_MPU (1 << 0) /* all divide by 1 */ 200 #define RVII_CM_CLKSEL_MPU_VAL RVII_CLKSEL_MPU 201 202 #define RVII_CLKSEL_DSP (1 << 0) 203 #define RVII_CLKSEL_DSP_IF (1 << 5) 204 #define RVII_SYNC_DSP (0 << 7) 205 #define RVII_CLKSEL_IVA (1 << 8) 206 #define RVII_SYNC_IVA (0 << 13) 207 #define RVII_CM_CLKSEL_DSP_VAL (RVII_SYNC_IVA | RVII_CLKSEL_IVA | \ 208 RVII_SYNC_DSP | RVII_CLKSEL_DSP_IF | \ 209 RVII_CLKSEL_DSP) 210 211 #define RVII_CLKSEL_GFX (1 << 0) 212 #define RVII_CM_CLKSEL_GFX_VAL RVII_CLKSEL_GFX 213 214 /*------------------------------------------------------------------------- 215 * 2430 Target modes: Along with each configuration the CPU has several 216 * modes which goes along with them. Modes mainly are the addition of 217 * describe DPLL combinations to go along with a ratio. 218 *-------------------------------------------------------------------------*/ 219 220 /* Hardware governed */ 221 #define MX_48M_SRC (0 << 3) 222 #define MX_54M_SRC (0 << 5) 223 #define MX_APLLS_CLIKIN_12 (3 << 23) 224 #define MX_APLLS_CLIKIN_13 (2 << 23) 225 #define MX_APLLS_CLIKIN_19_2 (0 << 23) 226 227 /* 228 * 2430 - standalone, 2*ref*M/(n+1), M/N is for exactness not relock speed 229 * #5a (ratio1) baseport-target, target DPLL = 266*2 = 532MHz 230 */ 231 #define M5A_DPLL_MULT_12 (133 << 12) 232 #define M5A_DPLL_DIV_12 (5 << 8) 233 #define M5A_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 234 M5A_DPLL_DIV_12 | M5A_DPLL_MULT_12 | \ 235 MX_APLLS_CLIKIN_12) 236 #define M5A_DPLL_MULT_13 (61 << 12) 237 #define M5A_DPLL_DIV_13 (2 << 8) 238 #define M5A_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 239 M5A_DPLL_DIV_13 | M5A_DPLL_MULT_13 | \ 240 MX_APLLS_CLIKIN_13) 241 #define M5A_DPLL_MULT_19 (55 << 12) 242 #define M5A_DPLL_DIV_19 (3 << 8) 243 #define M5A_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ 244 M5A_DPLL_DIV_19 | M5A_DPLL_MULT_19 | \ 245 MX_APLLS_CLIKIN_19_2) 246 /* #5b (ratio1) target DPLL = 200*2 = 400MHz */ 247 #define M5B_DPLL_MULT_12 (50 << 12) 248 #define M5B_DPLL_DIV_12 (2 << 8) 249 #define M5B_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 250 M5B_DPLL_DIV_12 | M5B_DPLL_MULT_12 | \ 251 MX_APLLS_CLIKIN_12) 252 #define M5B_DPLL_MULT_13 (200 << 12) 253 #define M5B_DPLL_DIV_13 (12 << 8) 254 255 #define M5B_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 256 M5B_DPLL_DIV_13 | M5B_DPLL_MULT_13 | \ 257 MX_APLLS_CLIKIN_13) 258 #define M5B_DPLL_MULT_19 (125 << 12) 259 #define M5B_DPLL_DIV_19 (31 << 8) 260 #define M5B_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ 261 M5B_DPLL_DIV_19 | M5B_DPLL_MULT_19 | \ 262 MX_APLLS_CLIKIN_19_2) 263 /* 264 * #4 (ratio2), DPLL = 399*2 = 798MHz, L3=133MHz 265 */ 266 #define M4_DPLL_MULT_12 (133 << 12) 267 #define M4_DPLL_DIV_12 (3 << 8) 268 #define M4_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 269 M4_DPLL_DIV_12 | M4_DPLL_MULT_12 | \ 270 MX_APLLS_CLIKIN_12) 271 272 #define M4_DPLL_MULT_13 (399 << 12) 273 #define M4_DPLL_DIV_13 (12 << 8) 274 #define M4_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 275 M4_DPLL_DIV_13 | M4_DPLL_MULT_13 | \ 276 MX_APLLS_CLIKIN_13) 277 278 #define M4_DPLL_MULT_19 (145 << 12) 279 #define M4_DPLL_DIV_19 (6 << 8) 280 #define M4_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ 281 M4_DPLL_DIV_19 | M4_DPLL_MULT_19 | \ 282 MX_APLLS_CLIKIN_19_2) 283 284 /* 285 * #3 (ratio2) baseport-target, target DPLL = 330*2 = 660MHz 286 */ 287 #define M3_DPLL_MULT_12 (55 << 12) 288 #define M3_DPLL_DIV_12 (1 << 8) 289 #define M3_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 290 M3_DPLL_DIV_12 | M3_DPLL_MULT_12 | \ 291 MX_APLLS_CLIKIN_12) 292 #define M3_DPLL_MULT_13 (76 << 12) 293 #define M3_DPLL_DIV_13 (2 << 8) 294 #define M3_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 295 M3_DPLL_DIV_13 | M3_DPLL_MULT_13 | \ 296 MX_APLLS_CLIKIN_13) 297 #define M3_DPLL_MULT_19 (17 << 12) 298 #define M3_DPLL_DIV_19 (0 << 8) 299 #define M3_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ 300 M3_DPLL_DIV_19 | M3_DPLL_MULT_19 | \ 301 MX_APLLS_CLIKIN_19_2) 302 303 /* 304 * #2 (ratio1) DPLL = 330*2 = 660MHz, L3=165MHz 305 */ 306 #define M2_DPLL_MULT_12 (55 << 12) 307 #define M2_DPLL_DIV_12 (1 << 8) 308 #define M2_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 309 M2_DPLL_DIV_12 | M2_DPLL_MULT_12 | \ 310 MX_APLLS_CLIKIN_12) 311 312 /* Speed changes - Used 658.7MHz instead of 660MHz for LP-Refresh M=76 N=2, 313 * relock time issue */ 314 /* Core frequency changed from 330/165 to 329/164 MHz*/ 315 #define M2_DPLL_MULT_13 (76 << 12) 316 #define M2_DPLL_DIV_13 (2 << 8) 317 #define M2_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 318 M2_DPLL_DIV_13 | M2_DPLL_MULT_13 | \ 319 MX_APLLS_CLIKIN_13) 320 321 #define M2_DPLL_MULT_19 (17 << 12) 322 #define M2_DPLL_DIV_19 (0 << 8) 323 #define M2_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ 324 M2_DPLL_DIV_19 | M2_DPLL_MULT_19 | \ 325 MX_APLLS_CLIKIN_19_2) 326 327 /* boot (boot) */ 328 #define MB_DPLL_MULT (1 << 12) 329 #define MB_DPLL_DIV (0 << 8) 330 #define MB_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 331 MB_DPLL_DIV | MB_DPLL_MULT | \ 332 MX_APLLS_CLIKIN_12) 333 334 #define MB_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 335 MB_DPLL_DIV | MB_DPLL_MULT | \ 336 MX_APLLS_CLIKIN_13) 337 338 #define MB_CM_CLKSEL1_PLL_19_VAL (MX_48M_SRC | MX_54M_SRC | \ 339 MB_DPLL_DIV | MB_DPLL_MULT | \ 340 MX_APLLS_CLIKIN_19) 341 342 /* 343 * 2430 - chassis (sedna) 344 * 165 (ratio1) same as above #2 345 * 150 (ratio1) 346 * 133 (ratio2) same as above #4 347 * 110 (ratio2) same as above #3 348 * 104 (ratio2) 349 * boot (boot) 350 */ 351 352 /* PRCM I target DPLL = 2*330MHz = 660MHz */ 353 #define MI_DPLL_MULT_12 (55 << 12) 354 #define MI_DPLL_DIV_12 (1 << 8) 355 #define MI_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 356 MI_DPLL_DIV_12 | MI_DPLL_MULT_12 | \ 357 MX_APLLS_CLIKIN_12) 358 359 /* 360 * 2420 Equivalent - mode registers 361 * PRCM II , target DPLL = 2*300MHz = 600MHz 362 */ 363 #define MII_DPLL_MULT_12 (50 << 12) 364 #define MII_DPLL_DIV_12 (1 << 8) 365 #define MII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 366 MII_DPLL_DIV_12 | MII_DPLL_MULT_12 | \ 367 MX_APLLS_CLIKIN_12) 368 #define MII_DPLL_MULT_13 (300 << 12) 369 #define MII_DPLL_DIV_13 (12 << 8) 370 #define MII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 371 MII_DPLL_DIV_13 | MII_DPLL_MULT_13 | \ 372 MX_APLLS_CLIKIN_13) 373 374 /* PRCM III target DPLL = 2*266 = 532MHz*/ 375 #define MIII_DPLL_MULT_12 (133 << 12) 376 #define MIII_DPLL_DIV_12 (5 << 8) 377 #define MIII_CM_CLKSEL1_PLL_12_VAL (MX_48M_SRC | MX_54M_SRC | \ 378 MIII_DPLL_DIV_12 | \ 379 MIII_DPLL_MULT_12 | MX_APLLS_CLIKIN_12) 380 #define MIII_DPLL_MULT_13 (266 << 12) 381 #define MIII_DPLL_DIV_13 (12 << 8) 382 #define MIII_CM_CLKSEL1_PLL_13_VAL (MX_48M_SRC | MX_54M_SRC | \ 383 MIII_DPLL_DIV_13 | \ 384 MIII_DPLL_MULT_13 | MX_APLLS_CLIKIN_13) 385 386 /* PRCM VII (boot bypass) */ 387 #define MVII_CM_CLKSEL1_PLL_12_VAL MB_CM_CLKSEL1_PLL_12_VAL 388 #define MVII_CM_CLKSEL1_PLL_13_VAL MB_CM_CLKSEL1_PLL_13_VAL 389 390 /* High and low operation value */ 391 #define MX_CLKSEL2_PLL_2x_VAL (2 << 0) 392 #define MX_CLKSEL2_PLL_1x_VAL (1 << 0) 393 394 /* MPU speed defines */ 395 #define S12M 12000000 396 #define S13M 13000000 397 #define S19M 19200000 398 #define S26M 26000000 399 #define S100M 100000000 400 #define S133M 133000000 401 #define S150M 150000000 402 #define S164M 164000000 403 #define S165M 165000000 404 #define S199M 199000000 405 #define S200M 200000000 406 #define S266M 266000000 407 #define S300M 300000000 408 #define S329M 329000000 409 #define S330M 330000000 410 #define S399M 399000000 411 #define S400M 400000000 412 #define S532M 532000000 413 #define S600M 600000000 414 #define S658M 658000000 415 #define S660M 660000000 416 #define S798M 798000000 417 418 419 extern const struct prcm_config omap2420_rate_table[]; 420 421 #ifdef CONFIG_SOC_OMAP2430 422 extern const struct prcm_config omap2430_rate_table[]; 423 #else 424 #define omap2430_rate_table NULL 425 #endif 426 extern const struct prcm_config *rate_table; 427 extern const struct prcm_config *curr_prcm_set; 428 429 #endif 430