| /linux-6.6.21/drivers/usb/storage/ |
| D | uas.c | 41 int qdepth, resetting; member
108 if (devinfo->resetting) in uas_do_work()
313 if (devinfo->resetting) in uas_stat_cmplt()
411 if (devinfo->resetting) in uas_data_cmplt()
657 if (devinfo->resetting) { in uas_queuecommand_lck()
783 devinfo->resetting = 1; in uas_eh_device_reset_handler()
794 devinfo->resetting = 0; in uas_eh_device_reset_handler()
1020 devinfo->resetting = 0; in uas_probe()
1206 devinfo->resetting = 1; in uas_disconnect()
|
| /linux-6.6.21/drivers/net/can/ |
| D | grcan.c | 305 bool resetting; member
562 if (!priv->resetting && !priv->closing && in grcan_lost_one_shot_frame()
693 if (!priv->resetting && !priv->closing) { in grcan_err()
819 priv->resetting = false; in grcan_running_reset()
912 if (!priv->resetting && !priv->closing) { in grcan_initiate_running_reset()
913 priv->resetting = true; in grcan_initiate_running_reset()
1028 if (priv->closing || priv->resetting) { in grcan_set_mode()
1082 priv->resetting = false; in grcan_open()
1141 if (!priv->resetting && !priv->closing && in grcan_transmit_catch_up()
1291 if (!priv->resetting && !priv->closing) { in grcan_txbug_workaround()
|
| /linux-6.6.21/drivers/input/misc/ |
| D | cm109.c | 117 unsigned resetting:1; member
623 if (!dev->resetting) in cm109_input_ev()
856 dev->resetting = 1; in cm109_usb_pre_reset()
868 dev->resetting = 0; in cm109_usb_post_reset()
|
| /linux-6.6.21/Documentation/hwmon/ |
| D | lm92.rst | 44 control the thresholds for resetting alarms.
|
| /linux-6.6.21/drivers/net/ethernet/i825xx/ |
| D | ether1.c | 507 priv(dev)->resetting = 1; in ether1_init_for_open()
910 if (priv(dev)->resetting == 0) in ether1_interrupt()
913 priv(dev)->resetting += 1; in ether1_interrupt()
919 if (priv(dev)->resetting == 2) in ether1_interrupt()
920 priv(dev)->resetting = 0; in ether1_interrupt()
|
| D | ether1.h | 44 unsigned char resetting; member
|
| /linux-6.6.21/Documentation/ABI/testing/ |
| D | sysfs-bus-fsi | 45 Provides a means of resetting the cfam that is attached to the
|
| D | sysfs-block-zram | 21 The reset file is write-only and allows resetting the
47 compressed data. For resetting the value, you should write
|
| D | sysfs-bus-cdx | 36 On resetting the device, the corresponding driver is notified
|
| D | sysfs-bus-pci-devices-cciss | 71 a dump device, as kdump requires resetting the device in order
|
| /linux-6.6.21/Documentation/devicetree/bindings/net/nfc/ |
| D | st,st-nci.yaml | 20 description: Output GPIO pin used for resetting the controller
|
| /linux-6.6.21/Documentation/devicetree/bindings/hwmon/ |
| D | pwm-fan.yaml | 31 it must be self resetting edge interrupts.
|
| /linux-6.6.21/Documentation/devicetree/bindings/usb/ |
| D | cdns,usb3.yaml | 70 description: Enable resetting of PHY if Rx fail is detected
|
| /linux-6.6.21/Documentation/networking/device_drivers/qlogic/ |
| D | qlge.rst | 117 devlink tool has to wait for 5 secs for the resetting to be
|
| /linux-6.6.21/Documentation/devicetree/bindings/clock/ |
| D | nvidia,tegra20-car.yaml | 25 RSTGEN provides the registers needed to control resetting of each block in
|
| D | nvidia,tegra124-car.yaml | 25 RSTGEN provides the registers needed to control resetting of each block in
|
| /linux-6.6.21/Documentation/i2c/ |
| D | fault-codes.rst | 14 some cases, such as re-initializing (and maybe resetting). After such
63 SMBus adapter) needs some fault recovery (such as resetting),
|
| /linux-6.6.21/drivers/clk/baikal-t1/ |
| D | Kconfig | 8 responsible for the chip subsystems clocking and resetting. It
|
| /linux-6.6.21/Documentation/devicetree/bindings/net/ |
| D | smsc,lan9115.yaml | 70 Indicates that MAC address needs to be saved before resetting the
|
| /linux-6.6.21/Documentation/devicetree/bindings/iio/pressure/ |
| D | honeywell,mprls0025pa.yaml | 49 Optional GPIO for resetting the device.
|
| /linux-6.6.21/Documentation/devicetree/bindings/arm/ |
| D | syna.txt | 46 CPU control register allows various operations on CPUs, like resetting them
|
| /linux-6.6.21/Documentation/driver-api/ |
| D | libata.rst | 568 gathering and could trigger complex error handling (say, resetting &
834 it forget about the timed out command, resetting is necessary. The timed
862 During EH, resetting is necessary in the following cases.
881 HBA resetting is implementation specific. For a controller complying to
906 some level of resetting, possibly similar level with software reset.
922 This is the preferred way of resetting a SATA device. In effect,
927 One more thing to consider when resetting devices is that resetting
|
| /linux-6.6.21/drivers/scsi/ |
| D | aha152x.c | 315 resetting = 0x0400, /* BUS DEVICE RESET is pending */ enumerator
939 if (acp->phase & (resetting | check_condition)) { in aha152x_internal_queue()
961 if ((phase & resetting) || !scsi_sglist(SCpnt)) { in aha152x_internal_queue()
1020 if (aha152x_priv(SCpnt)->phase & resetting) in aha152x_scsi_done()
1092 aha152x_internal_queue(SCpnt, &done, resetting); in aha152x_device_reset()
1483 if (!(aha152x_priv(ptr)->phase & resetting)) { in busfree_run()
1562 } else if (acp->phase & resetting) { in seldo_run()
|
| D | hptiop.h | 326 atomic_t resetting; member
|
| D | hptiop.c | 689 atomic_set(&hba->resetting, 0); in hptiop_message_callback()
1068 if (atomic_xchg(&hba->resetting, 1) == 0) { in hptiop_reset_hba()
1074 atomic_read(&hba->resetting) == 0, 60 * HZ); in hptiop_reset_hba()
1076 if (atomic_read(&hba->resetting)) { in hptiop_reset_hba()
1329 atomic_set(&hba->resetting, 0); in hptiop_probe()
|