| /linux-6.6.21/drivers/iio/pressure/ |
| D | Kconfig | 10 tristate "Honeywell ABP pressure sensor driver"
13 Say yes here to build support for the Honeywell ABP pressure
20 tristate "Bosch Sensortec BMP180/BMP280/BMP380/BMP580 pressure sensor driver"
27 and BMP580 pressure and temperature sensors. Also supports the BME280 with
57 tristate "All Sensors DLHL60D and DLHL60G low voltage digital pressure sensors"
63 pressure sensors driver.
69 tristate "Infineon DPS310 pressure and temperature sensor"
73 Support for the Infineon DPS310 digital barometric pressure sensor.
93 tristate "Hope RF HP03 temperature and pressure sensor driver"
97 Say yes here to build support for Hope RF HP03 pressure and
[all …]
|
| D | ms5611_core.c | 105 s32 *temp, s32 *pressure) in ms5611_read_temp_and_pressure() argument
110 ret = st->read_adc_temp_and_pressure(st, temp, pressure); in ms5611_read_temp_and_pressure()
117 return st->compensate_temp_and_pressure(st, temp, pressure); in ms5611_read_temp_and_pressure()
121 s32 *temp, s32 *pressure) in ms5611_temp_and_pressure_compensate() argument
123 s32 t = *temp, p = *pressure; in ms5611_temp_and_pressure_compensate()
151 *pressure = (((p * sens) >> 21) - off) >> 15; in ms5611_temp_and_pressure_compensate()
157 s32 *temp, s32 *pressure) in ms5607_temp_and_pressure_compensate() argument
159 s32 t = *temp, p = *pressure; in ms5607_temp_and_pressure_compensate()
187 *pressure = (((p * sens) >> 21) - off) >> 15; in ms5607_temp_and_pressure_compensate()
241 s32 temp, pressure; in ms5611_read_raw() local
[all …]
|
| D | abp060mg.c | 104 u16 pressure; in abp060mg_get_measurement() local
118 pressure = be16_to_cpu(buf[0]); in abp060mg_get_measurement()
119 if (pressure & ABP060MG_ERROR_MASK) in abp060mg_get_measurement()
122 if (pressure < ABP060MG_MIN_COUNTS || pressure > ABP060MG_MAX_COUNTS) in abp060mg_get_measurement()
125 *val = pressure; in abp060mg_get_measurement()
|
| /linux-6.6.21/Documentation/devicetree/bindings/iio/pressure/ |
| D | honeywell,mprls0025pa.yaml | 4 $id: http://devicetree.org/schemas/iio/pressure/honeywell,mprls0025pa.yaml#
7 title: Honeywell mprls0025pa pressure sensor
13 Honeywell pressure sensor of model mprls0025pa.
18 There are many models with different pressure ranges available. The vendor
20 differ in the pressure range, unit and transfer function.
22 To support different models one need to specify the pressure range as well as
27 sensor. The minimal range value stands for the minimum pressure and the
28 maximum value also for the maximum pressure with linear relation inside the
33 products/sensors/pressure-sensors/board-mount-pressure-sensors/
55 Minimum pressure value the sensor can measure in pascal.
[all …]
|
| D | hoperf,hp03.yaml | 4 $id: http://devicetree.org/schemas/iio/pressure/hoperf,hp03.yaml#
7 title: HopeRF HP03 digital pressure/temperature sensors
13 Digital pressure and temperature sensor with an I2C interface.
41 pressure@77 {
|
| D | meas,ms5611.yaml | 4 $id: http://devicetree.org/schemas/iio/pressure/meas,ms5611.yaml#
7 title: Measurement Specialities ms5611 and similar pressure sensors
44 pressure@77 {
54 pressure@0 {
|
| D | murata,zpa2326.yaml | 4 $id: http://devicetree.org/schemas/iio/pressure/murata,zpa2326.yaml#
7 title: Murata ZPA2326 pressure sensor
47 pressure@5c {
59 pressure@0 {
|
| D | asc,dlhl60d.yaml | 4 $id: http://devicetree.org/schemas/iio/pressure/asc,dlhl60d.yaml#
7 title: All Sensors DLH series low voltage digital pressure sensors
13 Bindings for the All Sensors DLH series pressure sensors.
46 pressure@29 {
|
| /linux-6.6.21/Documentation/translations/zh_CN/accounting/ |
| D | psi.rst | 37 压力信息可通过/proc/pressure/ --cpu、memory、io文件分别获取。
74 示例：向/proc/pressure/memory写入"some 150000 1000000"将新增触发器，将在
75 1秒内至少一个任务阻塞于内存的总时间超过150ms时触发。向/proc/pressure/io写入
112 fds.fd = open("/proc/pressure/memory", O_RDWR | O_NONBLOCK);
114 printf("/proc/pressure/memory open error: %s\n",
121 printf("/proc/pressure/memory write error: %s\n",
152 此场景下cgroupfs挂载点的子目录包含cpu.pressure、memory.pressure、io.pressure文件，
153 内容格式与/proc/pressure/下的文件相同。
|
| /linux-6.6.21/Documentation/devicetree/bindings/input/touchscreen/ |
| D | resistive-adc-touch.yaml | 15 position measurement and optional pressure.
29 - description: pressure (optional)
39 - enum: [x, y, pressure]
40 - enum: [x, y, pressure]
41 - enum: [x, y, pressure]
55 touchscreen-min-pressure: true
75 touchscreen-min-pressure = <50000>;
77 io-channel-names = "y", "pressure", "x";
82 touchscreen-min-pressure = <50000>;
|
| D | ti,tsc2005.yaml | 51 touchscreen-fuzz-pressure: true
54 touchscreen-max-pressure: true
93 touchscreen-fuzz-pressure = <2>;
96 touchscreen-max-pressure = <2048>;
120 touchscreen-fuzz-pressure = <2>;
123 touchscreen-max-pressure = <2048>;
|
| D | ad7879.txt | 9 - touchscreen-max-pressure : maximum reported pressure
10 - adi,resistance-plate-x : total resistance of X-plate (for pressure
46 touchscreen-max-pressure = <4096>;
64 touchscreen-max-pressure = <4096>;
|
| D | colibri-vf50-ts.txt | 15 - pinctrl-1: pinctrl node for X/Y and pressure measurement (ADC) state pinmux
16 - vf50-ts-min-pressure: pressure level at which to stop measuring X/Y values
33 vf50-ts-min-pressure = <200>;
|
| D | touchscreen.yaml | 38 touchscreen-max-pressure:
39 description: maximum reported pressure (arbitrary range dependent on the controller)
42 touchscreen-min-pressure:
43 description: minimum pressure on the touchscreen to be achieved in order
55 touchscreen-fuzz-pressure:
56 description: pressure noise value of the absolute input device (arbitrary
|
| D | ads7846.txt | 64 touchscreen-max-pressure General touchscreen binding, see [1].
65 touchscreen-min-pressure General touchscreen binding, see [1].
79 ti,pressure-min Minimum reported pressure value
81 ti,pressure-max Maximum reported pressure value (u16).
102 ti,pressure-max = /bits/ 16 <255>;
|
| D | bu21029.txt | 14 - touchscreen-max-pressure: maximum pressure value
31 touchscreen-max-pressure = <4095>;
|
| D | cypress,cy8ctma140.yaml | 41 touchscreen-max-pressure: true
51 - touchscreen-max-pressure
64 touchscreen-max-pressure = <255>;
|
| /linux-6.6.21/mm/ |
| D | vmpressure.c | 111 static enum vmpressure_levels vmpressure_level(unsigned long pressure) in vmpressure_level() argument
113 if (pressure >= vmpressure_level_critical) in vmpressure_level()
115 else if (pressure >= vmpressure_level_med) in vmpressure_level()
124 unsigned long pressure = 0; in vmpressure_calc_level() local
140 pressure = scale - (reclaimed * scale / scanned); in vmpressure_calc_level()
141 pressure = pressure * 100 / scale; in vmpressure_calc_level()
144 pr_debug("%s: %3lu (s: %lu r: %lu)\n", __func__, pressure, in vmpressure_calc_level()
147 return vmpressure_level(pressure); in vmpressure_calc_level()
|
| /linux-6.6.21/drivers/input/touchscreen/ |
| D | wm831x-ts.c | 64 bool pressure; member
92 if (wm831x_ts->pressure) in wm831x_ts_data_irq()
139 if (wm831x_ts->pressure) in wm831x_ts_data_irq()
167 if (wm831x_ts->pressure) in wm831x_ts_pen_down_irq()
271 wm831x_ts->pressure = pdata->pressure; in wm831x_ts_probe()
273 wm831x_ts->pressure = true; in wm831x_ts_probe()
281 WARN_ON(pdata->pressure && pdata->fivewire); in wm831x_ts_probe()
282 wm831x_ts->pressure = false; in wm831x_ts_probe()
355 if (wm831x_ts->pressure) in wm831x_ts_probe()
|
| D | resistive-adc-touch.c | 50 bool pressure; member
92 if ((!x && !y) || (st->pressure && (press < st->pressure_min))) { in grts_cb()
101 if (st->pressure) in grts_cb()
171 st->pressure = true; in grts_get_properties()
196 st->pressure = true; in grts_get_properties()
225 if (st->pressure) { in grts_probe()
248 if (st->pressure) in grts_probe()
|
| D | tsc200x-core.c | 115 int x, int y, int pressure) in tsc200x_update_pen_state() argument
117 if (pressure) { in tsc200x_update_pen_state()
119 input_report_abs(ts->idev, ABS_PRESSURE, pressure); in tsc200x_update_pen_state()
121 input_report_key(ts->idev, BTN_TOUCH, !!pressure); in tsc200x_update_pen_state()
133 pressure); in tsc200x_update_pen_state()
140 unsigned int pressure; in tsc200x_irq_thread() local
180 pressure = tsdata.x * (tsdata.z2 - tsdata.z1) / tsdata.z1; in tsc200x_irq_thread()
181 pressure = pressure * ts->x_plate_ohm / 4096; in tsc200x_irq_thread()
182 if (unlikely(pressure > MAX_12BIT)) in tsc200x_irq_thread()
187 tsc200x_update_pen_state(ts, tsdata.x, tsdata.y, pressure); in tsc200x_irq_thread()
|
| D | mainstone-wm97xx.c | 85 static int pressure; variable
86 module_param(pressure, int, 0);
87 MODULE_PARM_DESC(pressure, "Pressure readback (1 = pressure, 0 = no pressure)");
143 if (pressure) in wm97xx_acc_pen_down()
|
| /linux-6.6.21/Documentation/accounting/ |
| D | psi.rst | 38 respective file in /proc/pressure/ -- cpu, memory, and io.
67 Monitoring for pressure thresholds
71 pressure exceeds certain thresholds.
78 /proc/pressure/ representing the resource to be monitored and write the
85 For example writing "some 150000 1000000" into /proc/pressure/memory
87 1sec time window. Writing "full 50000 1000000" into /proc/pressure/io
142 fds.fd = open("/proc/pressure/memory", O_RDWR | O_NONBLOCK);
144 printf("/proc/pressure/memory open error: %s\n",
151 printf("/proc/pressure/memory write error: %s\n",
182 mounted, pressure stall information is also tracked for tasks grouped
[all …]
|
| /linux-6.6.21/tools/testing/selftests/hid/tests/ |
| D | test_wacom_generic.py | 191 self, x, y, pressure, buttons=None, toolid=None, proximity=None, reportID=None argument
223 report.tippressure = pressure
224 report.tipswitch = pressure > 0
263 def event(self, x, y, pressure, buttons=None, toolid=None, proximity=None): argument
275 r = self.create_report(x, y, pressure, buttons, toolid, proximity)
640 pressure=300,
654 uhdev.event(110, 220, pressure=0),
666 pressure=0,
676 uhdev.event(130, 240, pressure=0), [], auto_syn=False, strict=True
697 pressure=0,
[all …]
|
| /linux-6.6.21/drivers/input/mouse/ |
| D | synaptics_usb.c | 107 unsigned int pressure; in synusb_report_stick() local
109 pressure = synusb->data[6]; in synusb_report_stick()
113 if (pressure > 0) { in synusb_report_stick()
118 input_report_abs(input_dev, ABS_PRESSURE, pressure); in synusb_report_stick()
130 unsigned int pressure, w; in synusb_report_touchpad() local
132 pressure = synusb->data[6]; in synusb_report_touchpad()
137 if (pressure > 0) { in synusb_report_touchpad()
163 if (pressure > 30) in synusb_report_touchpad()
165 if (pressure < 25) in synusb_report_touchpad()
174 input_report_abs(input_dev, ABS_PRESSURE, pressure); in synusb_report_touchpad()
|