| /linux-6.6.21/Documentation/devicetree/bindings/arm/marvell/ |
| D | kirkwood.txt | 12 cpus/cpu@0 with three clocks, "cpu_clk", "ddrclk" and "powersave",
13 where the "powersave" clock is a gating clock used to switch the CPU
26 clock-names = "cpu_clk", "ddrclk", "powersave";
|
| /linux-6.6.21/tools/testing/selftests/intel_pstate/ |
| D | run.sh | 98 cpupower frequency-set -g powersave --max=${freq}MHz >& /dev/null
102 [ $EVALUATE_ONLY -eq 0 ] && cpupower frequency-set -g powersave --max=${max_freq}MHz >& /dev/null
|
| /linux-6.6.21/arch/powerpc/platforms/pasemi/ |
| D | Makefile | 2 obj-y += setup.o pci.o time.o idle.o powersave.o iommu.o dma_lib.o misc.o
|
| /linux-6.6.21/Documentation/sound/designs/ |
| D | index.rst | 14 powersave
|
| /linux-6.6.21/net/mac80211/ |
| D | pm.c | 109 sdata->u.mgd.powersave && in __ieee80211_suspend()
|
| D | Kconfig | 188 bool "Verbose powersave mode debugging"
261 bool "Verbose mesh powersave debugging"
266 powersave debugging messages (when mac80211 is taking part in a
|
| D | ieee80211_i.h | 486 bool powersave; /* powersave requested for this iface */ member
2352 bool powersave);
|
| D | mlme.c | 1054 else if (sdata->u.mgd.powersave) in ieee80211_assoc_link_elems()
1619 bool powersave) in ieee80211_send_nullfunc() argument
1632 if (powersave) in ieee80211_send_nullfunc()
2225 if (!mgd->powersave) in ieee80211_powersave_allowed()
6052 } else if (!local->pspolling && sdata->u.mgd.powersave) { in ieee80211_rx_mgmt_beacon()
6868 ifmgd->powersave = sdata->wdev.ps; in ieee80211_sta_setup_sdata()
7419 if (sdata->u.mgd.powersave) in ieee80211_setup_assoc_link()
|
| D | cfg.c | 3221 if (tdls_peer_found || !sdata->u.mgd.powersave) in __ieee80211_request_smps_mgd()
3251 if (enabled == sdata->u.mgd.powersave && in ieee80211_set_power_mgmt()
3255 sdata->u.mgd.powersave = enabled; in ieee80211_set_power_mgmt()
|
| D | rx.c | 4551 if (!sdata->u.mgd.powersave) in ieee80211_check_fast_rx()
|
| /linux-6.6.21/drivers/cpufreq/ |
| D | Kconfig | 56 bool "powersave"
59 Use the CPUFreq governor 'powersave' as default. This sets
122 tristate "'powersave' governor"
|
| D | Kconfig.x86 | 181 tristate "AMD frequency sensitivity feedback powersave bias"
184 This adds AMD-specific powersave bias function to the ondemand
|
| /linux-6.6.21/Documentation/networking/ |
| D | mac80211-auth-assoc-deauth.txt | 92 mac80211->driver: turn off powersave
|
| /linux-6.6.21/net/wireless/ |
| D | Kconfig | 163 bool "enable powersave by default"
166 This option enables powersave mode by default.
|
| /linux-6.6.21/drivers/net/wireless/ath/ath9k/ |
| D | channel.c | 1102 bool powersave) in ath_chanctx_send_vif_ps_frame() argument
1121 if (powersave) in ath_chanctx_send_vif_ps_frame()
1148 ath_chanctx_send_ps_frame(struct ath_softc *sc, bool powersave) in ath_chanctx_send_ps_frame() argument
1155 if (ath_chanctx_send_vif_ps_frame(sc, avp, powersave)) in ath_chanctx_send_ps_frame()
|
| /linux-6.6.21/Documentation/admin-guide/pm/ |
| D | intel_pstate.rst | 83 For example, the ``powersave`` P-state selection algorithm provided by
84 ``intel_pstate`` is not a counterpart of the generic ``powersave`` governor
88 active mode: ``powersave`` and ``performance``. The way they both operate
134 HWP + ``powersave``
157 ``powersave`` or ``performance``, depending on the ``scaling_governor`` policy
176 ``powersave``
619 affects decisions made by the scaling governors, except for ``powersave`` and
|
| D | cpufreq.rst | 367 ``powersave``
374 ``powersave`` and whenever the ``scaling_max_freq`` or ``scaling_min_freq``
517 for the AMD frequency sensitivity powersave bias driver
521 If the AMD frequency sensitivity powersave bias driver is not loaded,
529 If the AMD frequency sensitivity powersave bias driver is loaded, the
545 the ``powersave_bias`` value, the sensitivity powersave bias driver
|
| D | amd-pstate.rst | 402 available cpufreq governors: ondemand conservative powersave userspace performance schedutil
|
| /linux-6.6.21/tools/power/cpupower/bench/ |
| D | README-BENCH | 29 powersave module.
|
| /linux-6.6.21/arch/arm/boot/dts/marvell/ |
| D | kirkwood.dtsi | 22 clock-names = "cpu_clk", "ddrclk", "powersave";
|
| /linux-6.6.21/Documentation/livepatch/ |
| D | shadow-vars.rst | 101 ("mac80211: fix AP powersave TX vs. wakeup race"), which added a
|
| /linux-6.6.21/sound/drivers/ |
| D | Kconfig | 254 See Documentation/sound/designs/powersave.rst for more details.
|
| /linux-6.6.21/Documentation/admin-guide/sysctl/ |
| D | kernel.rst | 1019 powersave-nap (PPC only)
1252 range of [0:600]. This could happen for instance if a powersave mode will
|
| /linux-6.6.21/Documentation/sound/ |
| D | alsa-configuration.rst | 1097 mode. See powersave.rst for details.
|
| /linux-6.6.21/Documentation/admin-guide/ |
| D | kernel-parameters.txt | 2153 intel_pstate in the active mode: powersave and
4564 powersave=off [PPC] This option disables power saving features.
|