Searched refs:fiber (Results 1 – 20 of 20) sorted by relevance
| /linux-6.6.21/Documentation/devicetree/bindings/net/ |
| D | ti,dp83822.yaml | 17 fiber-optic transceiver. Additionally, the DP83822 provides flexibility to
36 This property is only applicable if the fiber mode support is strapped
39 ti,fiber-mode:
43 If present the DP83822 PHY is configured to operate in fiber mode
46 If the fiber mode is not strapped then signal detection for the PHY
48 In fiber mode, auto-negotiation is disabled and the PHY can only work in
|
| D | micrel.txt | 40 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
42 Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled
44 registers whether the PHY is in fiber mode, so this boolean device tree
47 In fiber mode, auto-negotiation is disabled and the PHY can only work in
|
| D | keystone-netcp.txt | 101 - mac<->fiber mode: 3
|
| /linux-6.6.21/drivers/net/fddi/ |
| D | Kconfig | 12 run over copper or fiber. If you are connected to such a network and
23 This is support for the DEC FDDIcontroller 700 (DEFZA-AA, fiber)
|
| /linux-6.6.21/drivers/net/ethernet/alacritech/ |
| D | Kconfig | 24 both copper and fiber.
|
| /linux-6.6.21/drivers/net/hippi/ |
| D | Kconfig | 12 can run over copper (25m) or fiber (300m on multi-mode or 10km on
|
| /linux-6.6.21/drivers/net/phy/ |
| D | marvell.c | 1578 int fiber, int status) in marvell_read_status_page_an() argument
1607 if (!fiber) { in marvell_read_status_page_an()
1649 int fiber; in marvell_read_status_page() local
1668 fiber = 1; in marvell_read_status_page()
1670 fiber = 0; in marvell_read_status_page()
1677 phydev->port = fiber ? PORT_FIBRE : PORT_TP; in marvell_read_status_page()
1680 err = marvell_read_status_page_an(phydev, fiber, status); in marvell_read_status_page()
|
| D | Kconfig | 392 fiber connections.
|
| /linux-6.6.21/arch/arm64/boot/dts/hisilicon/ |
| D | hip06.dtsi | 543 media-type = "fiber";
551 media-type = "fiber";
|
| D | hip07.dtsi | 1452 media-type = "fiber";
1462 media-type = "fiber";
|
| /linux-6.6.21/drivers/net/dsa/microchip/ |
| D | ksz8795.c | 837 if (dev->ports[p].fiber) in ksz8_w_phy()
1351 p->fiber = 1; in ksz8_config_cpu_port()
1353 if (p->fiber) in ksz8_config_cpu_port()
|
| D | ksz_common.h | 110 u32 fiber:1; /* port is fiber */ member
|
| /linux-6.6.21/Documentation/networking/device_drivers/ethernet/intel/ |
| D | e1000e.rst | 327 between copper-based adapters and fiber-based adapters.
349 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | e1000.rst | 341 If the board uses a fiber interface, these keywords are ignored, and the
342 fiber interface board only links at 1000 Mbps full-duplex.
|
| D | i40e.rst | 370 between copper-based adapters and fiber-based adapters.
395 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | ixgbe.rst | 100 "ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters.
|
| D | ice.rst | 662 between copper-based adapters and fiber-based adapters.
|
| /linux-6.6.21/Documentation/networking/device_drivers/ethernet/dlink/ |
| D | dl2k.rst | 232 available for fiber adapter.
|
| /linux-6.6.21/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 11 fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
|
| /linux-6.6.21/Documentation/networking/device_drivers/ethernet/cirrus/ |
| D | cs89x0.rst | 71 or fiber networks).
|