| /linux-6.6.21/arch/arm/boot/dts/microchip/ |
| D | at91-natte.dtsi | 71 ti,charge-current = <2000>;
72 ti,charge-voltage = <16800>;
87 ti,charge-current = <2000>;
88 ti,charge-voltage = <16800>;
103 ti,charge-current = <2000>;
104 ti,charge-voltage = <16800>;
119 ti,charge-current = <2000>;
120 ti,charge-voltage = <16800>;
135 ti,charge-current = <2000>;
136 ti,charge-voltage = <16800>;
[all …]
|
| /linux-6.6.21/Documentation/devicetree/bindings/power/supply/ |
| D | gpio-charger.yaml | 38 charge-status-gpios:
42 charge-current-limit-gpios:
47 charge-current-limit-mapping:
58 charge-current-limit-gpios property. Bit 1 second to last
68 - charge-status-gpios
70 - charge-current-limit-gpios
73 charge-current-limit-gpios: [ charge-current-limit-mapping ]
74 charge-current-limit-mapping: [ charge-current-limit-gpios ]
87 charge-status-gpios = <&gpc 27 GPIO_ACTIVE_LOW>;
89 charge-current-limit-gpios = <&gpioA 11 GPIO_ACTIVE_HIGH>,
[all …]
|
| D | richtek,rt5033-charger.yaml | 27 Current of pre-charge mode. The pre-charge current levels are 350 mA
30 constant-charge-current-max-microamp:
31 Current of fast-charge mode. The fast-charge current levels are 700 mA
34 charge-term-current-microamp:
35 This property is end of charge current. Its level ranges from 150 mA
40 Voltage of pre-charge mode. If the battery voltage is below the pre-charge
41 threshold voltage, the charger is in pre-charge mode with pre-charge
44 constant-charge-voltage-max-microvolt:
|
| D | qcom,pm8941-charger.yaml | 23 - description: charge done
24 - description: charge fast mode
25 - description: charge trickle mode
43 qcom,fast-charge-current-limit:
47 description: Maximum charge current in uA; May be clamped to safety limits; Defaults to 1A
49 qcom,fast-charge-low-threshold-voltage:
57 qcom,fast-charge-high-threshold-voltage:
63 The fast charger will attempt to charge the battery to this voltage.
66 qcom,fast-charge-safe-voltage:
72 setting this will harmlessly fail. The property 'fast-charge-high-watermark' will
[all …]
|
| D | richtek,rt9455.yaml | 25 richtek,output-charge-current:
29 richtek,end-of-charge-percentage:
32 percent of the output charge current. When the current in constant-voltage phase drops
33 below output_charge_current x end-of-charge-percentage, charge is terminated.
61 - richtek,output-charge-current
62 - richtek,end-of-charge-percentage
82 richtek,output-charge-current = <500000>;
83 richtek,end-of-charge-percentage = <10>;
|
| D | rohm,bd99954.yaml | 33 # a) Trickle-charge with constant current (8).
34 # b) pre-charge with constant current (6)
35 # c) fast-charge with:
70 # - trickle-charge-current-microamp:
71 # Current used at trickle-charge phase (8 in above chart)
76 # Current used at pre-charge phase (6 in above chart)
80 # - constant-charge-current-max-microamp
81 # Current used at fast charge constant current phase (5 in above chart)
85 # - constant-charge-voltage-max-microvolt
96 # - re-charge-voltage-microvolt
[all …]
|
| D | battery.yaml | 51 re-charge-voltage-microvolt:
63 charge-full-design-microamp-hours:
66 trickle-charge-current-microamp:
67 description: current for trickle-charge phase
70 description: current for pre-charge phase
75 charge-term-current-microamp:
76 description: current for charge termination phase
78 constant-charge-current-max-microamp:
81 constant-charge-voltage-max-microvolt:
151 re-charge-voltage-microvolt = <250000>;
[all …]
|
| D | sc2731-charger.yaml | 29 - charge-term-current-microamp: current for charge termination phase.
30 - constant-charge-voltage-max-microvolt: maximum constant input voltage.
38 charge-term-current-microamp = <120000>;
39 constant-charge-voltage-max-microvolt = <4350000>;
|
| D | summit,smb347-charger.yaml | 42 summit,enable-charge-control:
51 description: Voltage threshold to transit to fast charge mode (in uV)
61 summit,charge-current-compensation-microamp:
114 summit,charge-current-compensation-microamp:
127 summit,charge-current-compensation-microamp:
156 summit,enable-charge-control = <SMB3XX_CHG_ENABLE_PIN_ACTIVE_HIGH>;
179 constant-charge-current-max-microamp = <1800000>;
|
| D | bq2515x.yaml | 14 The BQ2515x family is a highly integrated battery charge management IC that
47 charge-enable-gpios:
71 constant-charge-current-max-microamp = <50000>;
73 constant-charge-voltage-max-microvolt = <4000000>;
89 charge-enable-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
|
| D | cpcap-charger.yaml | 29 - description: reverse charge interrupt
33 - description: charge current 2 interrupt
34 - description: charge current 1 interrupt
55 - description: battery charge current
69 charge controller that is controlled with two GPIOs
|
| D | bq25890.yaml | 38 ti,charge-current:
45 charge will be terminated when current in constant-voltage phase
50 description: maximum charge current during precharge phase (in uA)
79 temperature above which the charge current is lowered, to avoid overheating
93 - ti,charge-current
117 ti,charge-current = <1000000>;
|
| D | maxim,max14577.yaml | 39 maxim,fast-charge-uamp:
57 - maxim,fast-charge-uamp
71 maxim,fast-charge-uamp:
80 maxim,fast-charge-uamp:
|
| D | sc27xx-fg.yaml | 38 - const: charge-vol
70 charge-full-design-microamp-hours = <1900000>;
71 constant-charge-voltage-max-microvolt = <4350000>;
92 io-channel-names = "bat-temp", "charge-vol";
|
| D | richtek,rt9467.yaml | 17 regulation, and charge termination. The charge current is regulated through
38 charge-enable-gpios:
72 charge-enable-gpios = <&gpio26 1 GPIO_ACTIVE_LOW>;
|
| D | bq24190.yaml | 54 - precharge-current-microamp: maximum charge current during precharge phase
56 - charge-term-current-microamp: a charge cycle terminates when the battery voltage is
75 charge-term-current-microamp = <128000>;
|
| D | bq2415x.yaml | 48 ti,charge-current:
55 charge will be terminated when current in constant-voltage phase drops
72 - ti,charge-current
91 ti,charge-current = <650>;
|
| /linux-6.6.21/drivers/macintosh/ |
| D | apm_emu.c | 25 long charge = -1; in pmu_apm_get_power_status() local
43 if (charge < 0) in pmu_apm_get_power_status()
44 charge = 0; in pmu_apm_get_power_status()
45 percentage += (pmu_batteries[i].charge * 100) / in pmu_apm_get_power_status()
47 charge += pmu_batteries[i].charge; in pmu_apm_get_power_status()
62 time_units = (charge * 59) / (amperage * -1); in pmu_apm_get_power_status()
64 time_units = (charge * 16440) / (amperage * -60); in pmu_apm_get_power_status()
|
| /linux-6.6.21/Documentation/power/ |
| D | power_supply_class.rst | 63 | **Because both "charge" (µAh) and "energy" (µWh) represents "capacity" |
88 batteries can typically charge at different rates.
125 design charge values, when battery considered full/empty.
131 These attributes means "last remembered value of charge when battery
132 became full/empty". It also could mean "value of charge when battery
140 the current charge counter (in µAh). This could easily
145 the maximum charge current during precharge phase of charge cycle
149 Charge termination current. The charge cycle terminates when battery
150 voltage is above recharge threshold, and charge current is below
154 constant charge current programmed by charger.
[all …]
|
| /linux-6.6.21/arch/arm64/boot/dts/rockchip/ |
| D | rk3326-odroid-go2.dts | 42 charge-full-design-microamp-hours = <3000000>;
43 charge-term-current-microamp = <300000>;
44 constant-charge-current-max-microamp = <2000000>;
45 constant-charge-voltage-max-microvolt = <4200000>;
|
| D | rk3566-anbernic-rg353vs.dts | 22 charge-full-design-microamp-hours = <3151000>;
23 charge-term-current-microamp = <300000>;
24 constant-charge-current-max-microamp = <2000000>;
25 constant-charge-voltage-max-microvolt = <4200000>;
|
| D | rk3566-anbernic-rg353ps.dts | 22 charge-full-design-microamp-hours = <3472000>;
23 charge-term-current-microamp = <300000>;
24 constant-charge-current-max-microamp = <2000000>;
25 constant-charge-voltage-max-microvolt = <4200000>;
|
| /linux-6.6.21/Documentation/ABI/testing/ |
| D | sysfs-driver-samsung-laptop | 27 Description: Max battery charge level can be modified, battery cycle
28 life can be extended by reducing the max battery charge
31 - 0 means normal battery mode (100% charge)
32 - 1 means battery life extender mode (80% charge)
38 Description: Use your USB ports to charge devices, even
|
| /linux-6.6.21/arch/arm/mach-pxa/ |
| D | sharpsl_pm.c | 300 sharpsl_pm.machinfo->charge(0); in sharpsl_charge_off()
310 sharpsl_pm.machinfo->charge(0); in sharpsl_charge_error()
327 sharpsl_pm.machinfo->charge(0); in sharpsl_charge_toggle()
329 sharpsl_pm.machinfo->charge(1); in sharpsl_charge_toggle()
519 sharpsl_pm.machinfo->charge(0); in sharpsl_check_battery_voltage()
681 sharpsl_pm.machinfo->charge(0); in sharpsl_off_charge_error()
707 sharpsl_pm.machinfo->charge(0); in sharpsl_off_charge_battery()
709 sharpsl_pm.machinfo->charge(1); in sharpsl_off_charge_battery()
727 sharpsl_pm.machinfo->charge(0); in sharpsl_off_charge_battery()
729 sharpsl_pm.machinfo->charge(1); in sharpsl_off_charge_battery()
[all …]
|
| /linux-6.6.21/Documentation/devicetree/bindings/rtc/ |
| D | rtc-palmas.txt | 16 - ti,backup-battery-charge-high-current: Enable high current charging in
19 charge battery to lower current i.e. < 100uA.
29 ti,backup-battery-charge-high-current;
|