| /linux-6.1.9/Documentation/ABI/testing/ |
| D | sysfs-class-net-janz-ican3 | 1 What: /sys/class/net/<iface>/termination
6 Value representing the can bus termination
8 Default: 1 (termination active)
9 Reading: get actual termination state
10 Writing: set actual termination state (0=no termination, 1=termination active)
|
| /linux-6.1.9/Documentation/devicetree/bindings/net/can/ |
| D | can-controller.yaml | 16 termination-gpios:
17 description: GPIO pin to enable CAN bus termination.
20 termination-ohms:
21 description: The resistance value of the CAN bus termination resistor.
|
| D | fsl,flexcan.yaml | 122 termination-gpios: true
123 termination-ohms: true
165 termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
166 termination-ohms = <120>;
|
| /linux-6.1.9/drivers/gpu/drm/i915/pxp/ |
| D | intel_pxp.c | 124 init_completion(&pxp->termination); in intel_pxp_init()
125 complete_all(&pxp->termination); in intel_pxp_init()
161 reinit_completion(&pxp->termination); in intel_pxp_mark_termination_in_progress()
212 if (!wait_for_completion_timeout(&pxp->termination, in intel_pxp_start()
|
| D | intel_pxp_session.c | 128 complete_all(&pxp->termination); in pxp_terminate()
137 complete_all(&pxp->termination); in pxp_terminate_complete()
|
| D | intel_pxp_types.h | 70 struct completion termination; member
|
| D | intel_pxp_debugfs.c | 54 if (!wait_for_completion_timeout(&pxp->termination, in pxp_terminate_set()
|
| /linux-6.1.9/Documentation/devicetree/bindings/iio/adc/ |
| D | adi,ad7280a.yaml | 47 adi,thermistor-termination:
50 Enable the thermistor termination function.
73 adi,thermistor-termination;
|
| /linux-6.1.9/Documentation/devicetree/bindings/phy/ |
| D | xlnx,zynqmp-psgtr.yaml | 69 xlnx,tx-termination-fix:
71 Include this for fixing functional issue with the TX termination
89 xlnx,tx-termination-fix: false
|
| /linux-6.1.9/Documentation/devicetree/bindings/power/supply/ |
| D | bq24257.yaml | 37 ti,termination-current:
79 - ti,termination-current
101 ti,termination-current = <50000>;
119 ti,termination-current = <50000>;
|
| D | bq2415x.yaml | 52 ti,termination-current:
73 - ti,termination-current
92 ti,termination-current = <100>;
|
| D | bq25890.yaml | 38 ti,termination-current:
90 - ti,termination-current
114 ti,termination-current = <50000>;
|
| D | sc2731-charger.yaml | 29 - charge-term-current-microamp: current for charge termination phase.
|
| /linux-6.1.9/drivers/scsi/ |
| D | advansys.c | 939 uchar termination; /* 11 0 - automatic */ member
1699 uchar termination; /* Term. Ctrl. bits 6-5 of SCSI_CFG1 register */ member
2387 h->disc_enable, h->termination); in asc_prt_adv_dvc_cfg()
2970 word = ep_3550->termination; in asc_prt_adv_board_eeprom()
2995 ep_3550->termination, termstr, in asc_prt_adv_board_eeprom()
4624 if (asc_dvc->cfg->termination == 0) { in AdvInitAsc3550Driver()
4629 asc_dvc->cfg->termination |= TERM_CTL_SEL; in AdvInitAsc3550Driver()
4639 asc_dvc->cfg->termination |= (TERM_CTL_H | TERM_CTL_L); in AdvInitAsc3550Driver()
4648 asc_dvc->cfg->termination |= TERM_CTL_H; in AdvInitAsc3550Driver()
4669 scsi_cfg1 |= (TERM_CTL_SEL | (~asc_dvc->cfg->termination & TERM_CTL)); in AdvInitAsc3550Driver()
[all …]
|
| /linux-6.1.9/arch/arm64/boot/dts/freescale/ |
| D | imx8mq-librem5-r2.dts | 18 ti,termination-current = <66000>; /* uA */
|
| D | imx8mq-librem5-r3.dtsi | 27 ti,termination-current = <144000>; /* uA */
|
| D | imx8mm-venice-gw72xx-0x-rs422.dts | 6 * - GPIO1_0 rs485_term selects on-chip termination
|
| D | imx8mm-venice-gw72xx-0x-rs485.dts | 6 * - GPIO1_0 rs485_term selects on-chip termination
|
| D | imx8mm-venice-gw73xx-0x-rs422.dts | 6 * - GPIO1_0 rs485_term selects on-chip termination
|
| D | imx8mm-venice-gw73xx-0x-rs485.dts | 6 * - GPIO1_0 rs485_term selects on-chip termination
|
| /linux-6.1.9/drivers/net/can/usb/ |
| D | mcba_usb.c | 140 u8 termination; member
471 priv->can.termination = MCBA_TERMINATION_ENABLED; in mcba_usb_process_ka_usb()
473 priv->can.termination = MCBA_TERMINATION_DISABLED; in mcba_usb_process_ka_usb()
792 usb_msg.termination = MCBA_VER_TERMINATION_ON; in mcba_set_termination()
794 usb_msg.termination = MCBA_VER_TERMINATION_OFF; in mcba_set_termination()
|
| /linux-6.1.9/Documentation/devicetree/bindings/display/bridge/ |
| D | analogix,anx7625.yaml | 69 Registers 10~19, bit 5:6 is [R termination control], these bits
70 adjust 50ohm impedance of DP tx termination. 00:55 ohm,
|
| /linux-6.1.9/drivers/net/can/dev/ |
| D | netlink.c | 351 priv->termination = termval; in can_changelink()
415 size += nla_total_size(sizeof(priv->termination)); /* IFLA_CAN_TERMINATION */ in can_get_size()
542 (nla_put_u16(skb, IFLA_CAN_TERMINATION, priv->termination) || in can_fill_info()
|
| /linux-6.1.9/Documentation/scsi/ |
| D | qlogicfas.rst | 68 The best way to test if your cables, termination, etc. are good is to
82 termination (the ACK can be reflected), or by noise when the chips
|
| /linux-6.1.9/Documentation/filesystems/ |
| D | netfs_library.rst | 515 With a termination handler function pointer::
559 Also provided is a pointer to a termination handler function and private
560 data to pass to that function. The termination function should be called
562 indicating whether the termination is definitely happening in the caller's
581 Also provided is a pointer to a termination handler function and private
582 data to pass to that function. The termination function should be called
584 indicating whether the termination is definitely happening in the caller's
|