/linux-6.1.9/drivers/rtc/ |
D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local 166 resistors = "1k Ohm"; in ds1343_show_tricklecharger() 170 resistors = "2k Ohm"; in ds1343_show_tricklecharger() 174 resistors = "4k Ohm"; in ds1343_show_tricklecharger() 183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
D | rtc-ds1305.c | 386 char *resistors = ""; in ds1305_proc() local 402 resistors = "2k Ohm"; in ds1305_proc() 405 resistors = "4k Ohm"; in ds1305_proc() 408 resistors = "8k Ohm"; in ds1305_proc() 417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
|
/linux-6.1.9/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse() 123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
/linux-6.1.9/Documentation/devicetree/bindings/leds/ |
D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors 34 resistors limits the maximum flash current. This must be set 43 resistors limits the maximum torch current. This must be set
|
/linux-6.1.9/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
/linux-6.1.9/Documentation/hwmon/ |
D | ina3221.rst | 48 value for their shunt resistors) 53 value for their shunt resistors)
|
D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
D | ltc4261.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
D | ltc2945.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
D | ltc4245.rst | 49 rely on the sense resistors listed in Table 2: "Sense Resistor Values".
|
D | vt1211.rst | 84 external scaling resistors. This external scaling needs to be compensated for 89 The board level scaling resistors according to VIA's recommendation are as
|
/linux-6.1.9/Documentation/devicetree/bindings/pinctrl/ |
D | mediatek,mt6797-pinctrl.yaml | 109 Pull up setings for 2 pull resistors, R0 and R1. User can 120 Pull down settings for 2 pull resistors, R0 and R1. User can
|
D | mediatek,mt6779-pinctrl.yaml | 118 Pull up setings for 2 pull resistors, R0 and R1. User can 129 Pull down settings for 2 pull resistors, R0 and R1. User can
|
D | mediatek,pinctrl-mt6795.yaml | 131 Pull up setings for 2 pull resistors, R0 and R1. User can 142 Pull down settings for 2 pull resistors, R0 and R1. User can
|
D | mediatek,mt8183-pinctrl.yaml | 141 Pull up setings for 2 pull resistors, R0 and R1. User can 152 Pull down settings for 2 pull resistors, R0 and R1. User can
|
D | mediatek,mt7986-pinctrl.yaml | 313 Pull up setings for 2 pull resistors, R0 and R1. Valid arguments 325 Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
|
D | mediatek,mt65xx-pinctrl.yaml | 100 settings for 2 pull resistors, R0 and R1. User can configure those
|
/linux-6.1.9/Documentation/devicetree/bindings/hwmon/ |
D | ntc-thermistor.yaml | 13 Thermistors with negative temperature coefficient (NTC) are resistors that 60 We can use both pull-up and pull-down resistors at the same time, and then
|
/linux-6.1.9/Documentation/devicetree/bindings/gpio/ |
D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|
/linux-6.1.9/Documentation/devicetree/bindings/iio/imu/ |
D | st,lsm6dsx.yaml | 67 description: enable/disable internal i2c controller pullup resistors.
|
/linux-6.1.9/Documentation/ABI/stable/ |
D | sysfs-class-udc | 63 Allows users to disconnect data pullup resistors thus causing a
|
/linux-6.1.9/arch/arm/mach-s3c/ |
D | Kconfig.s3c64xx | 210 resistors fitted so that the card detects for 219 resistors fitted so that the card detects for
|
/linux-6.1.9/Documentation/devicetree/bindings/mfd/ |
D | gateworks-gsc.yaml | 92 description: Values of resistors for divider on raw ADC input
|
/linux-6.1.9/arch/arm/boot/dts/ |
D | sun6i-a31s-yones-toptech-bs1078-v2.dts | 165 /* Voltage source for I2C pullup resistors for I2C Bus 0 */
|