Home
last modified time | relevance | path

Searched refs:phydev_warn (Results 1 – 17 of 17) sorted by relevance

/linux-6.1.9/drivers/net/phy/
Dmicrochip.c95 phydev_warn(phydev, "Failed to get current page\n"); in lan88xx_TR_reg_set()
105 phydev_warn(phydev, "Failed to write TR low data\n"); in lan88xx_TR_reg_set()
112 phydev_warn(phydev, "Failed to write TR high data\n"); in lan88xx_TR_reg_set()
122 phydev_warn(phydev, "Failed to write data in reg\n"); in lan88xx_TR_reg_set()
129 phydev_warn(phydev, "TR Register[0x%X] configuration failed\n", in lan88xx_TR_reg_set()
145 phydev_warn(phydev, "Failed to Set Register[0x0F82]\n"); in lan88xx_config_TR_regs()
153 phydev_warn(phydev, "Failed to Set Register[0x168C]\n"); in lan88xx_config_TR_regs()
161 phydev_warn(phydev, "Failed to Set Register[0x17A2]\n"); in lan88xx_config_TR_regs()
170 phydev_warn(phydev, "Failed to Set Register[0x16A0]\n"); in lan88xx_config_TR_regs()
178 phydev_warn(phydev, "Failed to Set Register[0x16A6]\n"); in lan88xx_config_TR_regs()
[all …]
Dnxp-c45-tja11xx.c443 phydev_warn(priv->phydev, in nxp_c45_process_txts()
537 phydev_warn(phydev, "The period can be set only to 1 second."); in nxp_c45_perout_enable()
543 …phydev_warn(phydev, "The start time is not configurable. Should be set to 0 seconds and 0 nanoseco… in nxp_c45_perout_enable()
549 phydev_warn(phydev, "The phase can be set only to 0 or 500000000 nanoseconds."); in nxp_c45_perout_enable()
1008 phydev_warn(phydev, "Unsupported Master/Slave mode\n"); in nxp_c45_setup_master_slave()
Dphy-c45.c94 phydev_warn(phydev, "Unsupported Master/Slave mode\n"); in genphy_c45_pma_baset1_setup_master_slave()
221 phydev_warn(phydev, "Unsupported Master/Slave mode\n"); in genphy_c45_baset1_an_config_aneg()
Dintel-xway.c193 phydev_warn(phydev, in xway_gphy_rgmii_init()
Ddp83640.c568 phydev_warn(phydev, in enable_status_frames()
575 phydev_warn(phydev, "failed to add mc address\n"); in enable_status_frames()
578 phydev_warn(phydev, "failed to delete mc address\n"); in enable_status_frames()
Dphy.c1062 phydev_warn(phydev, "Error %d requesting IRQ %d, falling back to polling\n", in phy_request_interrupt()
1067 phydev_warn(phydev, "Can't enable interrupt, falling back to polling\n"); in phy_request_interrupt()
Dmicrochip_t1.c789 phydev_warn(phydev, "Unsupported Master/Slave mode\n"); in lan87xx_config_aneg()
Dadin.c245 phydev_warn(phydev, in adin_get_reg_value()
Ddp83867.c500 phydev_warn(phydev, in dp83867_verify_rgmii_cfg()
Dnxp-tja11xx.c248 phydev_warn(phydev, "Unsupported Master/Slave mode\n"); in tja11xx_config_aneg()
Dphy-core.c478 …phydev_warn(phydev, "Downshift occurred from negotiated speed %s to actual speed %s, check cabling… in phy_check_downshift()
Drealtek.c760 phydev_warn(phydev, "Unsupported Master/Slave mode\n"); in rtl9000a_config_aneg()
Dmarvell.c782 phydev_warn(phydev, "Fail to config marvell phy LED.\n"); in marvell_config_led()
1472 phydev_warn(phydev, "Fast Link Down detection requires EEE to be disabled!\n"); in m88e1540_set_fld()
Dphy_device.c2074 phydev_warn(phydev, "Unsupported Master/Slave mode\n"); in genphy_setup_master_slave()
Dmicrel.c1077 phydev_warn(phydev, in ksz9031_config_init()
/linux-6.1.9/drivers/net/ethernet/realtek/
Dr8169_phy_config.c444 phydev_warn(phydev, "chipset not ready for firmware\n"); in rtl8168d_apply_firmware_cond()
/linux-6.1.9/include/linux/
Dphy.h1588 #define phydev_warn(_phydev, format, args...) \ macro