Searched refs:conf2 (Results 1 – 12 of 12) sorted by relevance
| /linux-6.1.9/drivers/regulator/ |
| D | pv88090-regulator.c | 36 unsigned int conf2; member
184 .conf2 = PV88090_REG_##regl_name##_CONF2, \
275 unsigned int conf2, range, index; in pv88090_i2c_probe() local
338 pv88090_regulator_info[i].conf2, &conf2); in pv88090_i2c_probe()
342 conf2 = (conf2 >> PV88090_BUCK_VDAC_RANGE_SHIFT) & in pv88090_i2c_probe()
353 index = ((range << 1) | conf2); in pv88090_i2c_probe()
|
| D | pv88080-regulator.c | 39 unsigned int conf2; member
386 unsigned int conf2, conf5; in pv88080_i2c_probe() local
479 pv88080_regulator_info[i].conf2 in pv88080_i2c_probe()
493 pv88080_regulator_info[i].conf2, &conf2); in pv88080_i2c_probe()
496 conf2 = ((conf2 >> PV88080_BUCK_VDAC_RANGE_SHIFT) & in pv88080_i2c_probe()
507 pv88080_buck_vol[conf2].min_uV * (conf5+1); in pv88080_i2c_probe()
509 pv88080_buck_vol[conf2].uV_step * (conf5+1); in pv88080_i2c_probe()
511 ((pv88080_buck_vol[conf2].max_uV * (conf5+1)) in pv88080_i2c_probe()
|
| /linux-6.1.9/drivers/pinctrl/intel/ |
| D | pinctrl-lynxpoint.c | 306 void __iomem *conf2 = lp_gpio_reg(&lg->chip, pin, LP_CONFIG2); in lp_pin_dbg_show() local
317 seq_printf(s, "0x%08x 0x%08x", value, ioread32(conf2)); in lp_pin_dbg_show()
405 void __iomem *conf2 = lp_gpio_reg(&lg->chip, pin, LP_CONFIG2); in lp_gpio_request_enable() local
424 lp_gpio_enable_input(conf2); in lp_gpio_request_enable()
436 void __iomem *conf2 = lp_gpio_reg(&lg->chip, pin, LP_CONFIG2); in lp_gpio_disable_free() local
442 lp_gpio_disable_input(conf2); in lp_gpio_disable_free()
495 void __iomem *conf2 = lp_gpio_reg(&lg->chip, pin, LP_CONFIG2); in lp_pin_config_get() local
502 value = ioread32(conf2); in lp_pin_config_get()
538 void __iomem *conf2 = lp_gpio_reg(&lg->chip, pin, LP_CONFIG2); in lp_pin_config_set() local
546 value = ioread32(conf2); in lp_pin_config_set()
[all …]
|
| /linux-6.1.9/drivers/gpu/drm/mcde/ |
| D | mcde_display.c | 346 u32 conf2; in mcde_configure_overlay() local
356 conf2 = MCDE_OVL0CONF2; in mcde_configure_overlay()
364 conf2 = MCDE_OVL1CONF2; in mcde_configure_overlay()
372 conf2 = MCDE_OVL2CONF2; in mcde_configure_overlay()
380 conf2 = MCDE_OVL3CONF2; in mcde_configure_overlay()
388 conf2 = MCDE_OVL4CONF2; in mcde_configure_overlay()
396 conf2 = MCDE_OVL5CONF2; in mcde_configure_overlay()
463 writel(val, mcde->regs + conf2); in mcde_configure_overlay()
|
| /linux-6.1.9/arch/arm/boot/dts/ |
| D | gemini-nas4220b.dts | 117 conf2 {
|
| D | gemini-sq201.dts | 192 conf2 {
|
| D | gemini-sl93512r.dts | 196 conf2 {
|
| D | gemini-dlink-dns-313.dts | 235 conf2 {
|
| /linux-6.1.9/drivers/atm/ |
| D | lanai.c | 285 u32 conf1, conf2; /* CONFIG[12] registers */ member
499 reg_write(lanai, lanai->conf2, Config2_Reg); in conf2_write()
1977 lanai->conf2 |= CONFIG2_VCI0_NORMAL; in vci0_is_ok()
2009 lanai->conf2 &= ~CONFIG2_VCI0_NORMAL; in vci_is_ok()
2093 lanai->conf2 |= CONFIG2_CBR_ENABLE; in lanai_cbr_setup()
2099 lanai->conf2 &= ~CONFIG2_CBR_ENABLE; in lanai_cbr_shutdown()
2191 lanai->conf2 = (lanai->num_vci >= 512 ? CONFIG2_HOWMANY : 0) | in lanai_dev_open()
|
| /linux-6.1.9/Documentation/x86/x86_64/ |
| D | boot-options.rst | 213 pci=conf2
214 Use conf2 access.
|
| /linux-6.1.9/drivers/hwmon/ |
| D | adm1031.c | 78 u8 conf2; member
167 data->conf2 = adm1031_read_value(client, ADM1031_REG_CONF2); in adm1031_update_device()
|
| /linux-6.1.9/Documentation/admin-guide/ |
| D | kernel-parameters.txt | 4145 conf2 [X86] Force use of PCI Configuration Access
|