| /linux-6.1.9/drivers/pinctrl/ |
| D | pinctrl-lpc18xx.c | 243 LPC_P(1,3, GPIO, CTOUT, SGPIO, EMC, USB0, SSP1, R, SDMMC, 0, ND);
244 LPC_P(1,4, GPIO, CTOUT, SGPIO, EMC, USB0, SSP1, R, SDMMC, 0, ND);
245 LPC_P(1,5, GPIO, CTOUT, R, EMC, USB0, SSP1, SGPIO, SDMMC, 0, ND);
247 LPC_P(1,7, GPIO, UART1, CTOUT, EMC, USB0, R, R, R, 0, ND);
261 LPC_P(2,0, SGPIO, UART0, EMC, USB0, GPIO, R, TIMER3, ENET, 0, ND);
262 LPC_P(2,1, SGPIO, UART0, EMC, USB0, GPIO, R, TIMER3, R, 0, ND);
263 LPC_P(2,2, SGPIO, UART0, EMC, USB0, GPIO, CTIN, TIMER3, R, 0, ND);
264 LPC_P(2,3, SGPIO, I2C1, UART3, CTIN, GPIO, R, TIMER3, USB0, 0, HD);
265 LPC_P(2,4, SGPIO, I2C1, UART3, CTIN, GPIO, R, TIMER3, USB0, 0, HD);
266 LPC_P(2,5, SGPIO, CTIN, USB1, ADCTRIG, GPIO, R, TIMER3, USB0, 0, HD);
[all …]
|
| /linux-6.1.9/Documentation/devicetree/bindings/usb/ |
| D | fsl-usb.txt | 38 - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the
40 - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates
|
| /linux-6.1.9/arch/powerpc/boot/dts/ |
| D | mpc5121ads.dts | 125 /* mpc5121ads only uses USB0 */
130 /* USB0 using internal UTMI PHY */
|
| D | pdm360ng.dts | 131 /* USB0 using internal UTMI PHY */
|
| D | sequoia.dts | 155 USB0: ehci@e0000300 { label
|
| D | mpc5121.dtsi | 305 /* USB0 using internal UTMI PHY */
|
| D | canyonlands.dts | 166 USB0: ehci@bffd0400 { label
|
| /linux-6.1.9/arch/arm64/boot/dts/ti/ |
| D | k3-am62.dtsi | 56 <0x00 0x00703000 0x00 0x00703000 0x00 0x00000200>, /* USB0 debug trace */
67 <0x00 0x31000000 0x00 0x31000000 0x00 0x00050000>, /* USB0 DWC3 Core window */
|
| D | k3-am62a.dtsi | 56 <0x00 0x00703000 0x00 0x00703000 0x00 0x00000200>, /* USB0 debug trace */
68 <0x00 0x31000000 0x00 0x31000000 0x00 0x00050000>, /* USB0 DWC3 Core window */
|
| D | k3-j7200-common-proc-board.dts | 302 idle-states = <1>; /* USB0 to SERDES lane 3 */
|
| D | k3-j721e-common-proc-board.dts | 458 idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
|
| /linux-6.1.9/include/dt-bindings/clock/ |
| D | xlnx-zynqmp-clk.h | 47 #define USB0 35 macro
|
| /linux-6.1.9/arch/arm64/boot/dts/marvell/ |
| D | ac5-98dx35xx-rd.dts | 60 /* USB0 is a host USB */
|
| /linux-6.1.9/arch/arm/boot/dts/ |
| D | dove-sbc-a510.dts | 48 * 0.0 USB0 VBUS_EN (active high)
49 * 0.1 USB0 VBUS_GOOD
|
| D | sun7i-a20-bananapi.dts | 210 "", "USB0-DRV", "", "", "", "", "", "",
240 "TXD0", "RXD0", "IO-1", "PH3", "USB0-IDDET", "PH5", "", "",
|
| D | gemini.dtsi | 451 * This will claim pins for USB0 and USB1 at the same
454 * NOT using USB0 at 68000000 you wll have to add the
|
| D | sun8i-h2-plus-bananapi-m2-zero.dts | 253 "VCC-IO-EN", "USB0-ID", "WL-PWR-EN",
|
| D | am335x-pepper.dts | 568 /* USB0 Over-Current (active low) */
|
| D | imx6qdl-kontron-samx6i.dtsi | 779 /* USB0 */
|
| /linux-6.1.9/Documentation/devicetree/bindings/reset/ |
| D | nxp,lpc1850-rgu.txt | 23 17 USB0
|
| /linux-6.1.9/arch/sh/kernel/cpu/sh4a/ |
| D | setup-sh7724.c | 865 USB0, USB1, enumerator
927 INTC_VECT(USB0, 0xA20),
1005 INTC_GROUP(USB, USB0, USB1),
1043 { 0, 0, 0, CMT, 0, USB1, USB0, 0 } },
|
| D | setup-sh7757.c | 798 USB0, USB1, enumerator
859 INTC_VECT(USB0, 0x840),
973 IRQ9, IRQ8, SCIF1, SCIF0, USB0, 0, 0, USB1,
1073 { INT2PRI12, 0, 32, 8, { USB0, 0, IRQ15, USB1 } },
|
| /linux-6.1.9/drivers/phy/ |
| D | Kconfig | 35 This driver is need for USB0 support on LPC18xx/43xx and takes
|
| /linux-6.1.9/Documentation/devicetree/bindings/clock/ |
| D | lpc1850-cgu.txt | 46 1 BASE_USB0_CLK Base clock for USB0
|
| /linux-6.1.9/drivers/clk/nxp/ |
| D | clk-lpc18xx-cgu.c | 221 LPC1XX_CGU_BASE_CLK(USB0, base_usb0_src_ids, 0),
|