Home
last modified time | relevance | path

Searched refs:U2 (Results 1 – 23 of 23) sorted by relevance

/linux-6.1.9/Documentation/devicetree/bindings/phy/
Dmediatek,xsphy.yaml57 if only U2 ports provided, shouldn't use the property.
113 The value of slew rate calibrate (U2 phy)
120 The selection of VRT reference voltage (U2 phy)
127 The selection of HS_TX TERM reference voltage (U2 phy)
134 The selection of Internal Resistor (U2/U3 phy)
Dmediatek,tphy.yaml170 - description: internal R efuse for U2 PHY or U3/PCIe PHY
175 Available only for U2 PHY or U3/PCIe PHY of version 2/3, these
189 The value of slew rate calibrate (U2 phy)
196 The selection of VRT reference voltage (U2 phy)
203 The selection of HS_TX TERM reference voltage (U2 phy)
210 The selection of internal resistor (U2 phy)
217 The selection of disconnect threshold (U2 phy)
227 8.3% etc. (U2 phy)
/linux-6.1.9/arch/arm/boot/dts/
Dstm32mp15xx-dhcor-io1v8.dtsi9 /* Enpirion EP3A8LQI U2 on the DHCOR */
Dam335x-boneblue.dts176 AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_INPUT_PULLUP, MUX_MODE4) /* (U2) lcd_data9.uart5_rxd */
527 "UART5_RX", /* U2 */
Ddove-cm-a510.dtsi66 * U2: 2 dual-role USB2.0 ports
Dexynos4412-odroid-common.dtsi3 * Common definition for Hardkernel's Exynos4412 based ODROID-X/X2/U2/U3 boards
/linux-6.1.9/drivers/parisc/
DKconfig23 bool "U2/Uturn I/O MMU"
28 U2/Uturn chip in "Virtual Mode" and use the I/O MMU.
/linux-6.1.9/Documentation/ABI/testing/
Dsysfs-bus-usb-lvstest24 Set "U2 timeout" for the downstream port where Link Layer
Dsysfs-bus-usb149 and U2 exit latencies have been set in the BOS descriptor; if
155 or not USB3 hardware LPM U1 or U2 is enabled for the device.
/linux-6.1.9/drivers/net/wireless/
DKconfig92 Buffalo WLI-U2-KG125S
/linux-6.1.9/Documentation/devicetree/bindings/usb/
Dsnps,dwc3.yaml136 description: Set if we enable P3 OK for U2/SS Inactive quirk
197 description: Set if link entering into U2 needs to be disabled
/linux-6.1.9/Documentation/admin-guide/media/
Dem28xx-cardlist.rst270 - Kaiomy TVnPC U2
/linux-6.1.9/Documentation/scsi/
Daic7xxx.rst110 AHA-2940U2 OEM aic7891 PCI/64
115 AHA-2930U2 aic7890 PCI/32 LVD-HD68F SE-HD50F
/linux-6.1.9/drivers/pinctrl/aspeed/
Dpinctrl-aspeed-g5.c714 #define U2 91 macro
716 SIG_EXPR_LIST_DECL_SINGLE(U2, VPIHS, VPI24, VPI_24_RSVD_DESC, U2_DESC, COND2);
717 SIG_EXPR_LIST_DECL_SINGLE(U2, NRI1, NRI1, U2_DESC, COND2);
718 PIN_DECL_2(U2, GPIOL3, VPIHS, NRI1);
719 FUNC_GROUP_DECL(NRI1, U2);
929 FUNC_GROUP_DECL(VPI24, T1, U2, P4, P3, Y1, AB2, AA1, Y2, AA2, P5, R5, T5, V3,
2098 ASPEED_PINCTRL_PIN(U2),
Dpinctrl-aspeed-g4.c630 #define U2 77 macro
631 SSSF_PIN_DECL(U2, GPIOJ5, VGAVS, SIG_DESC_SET(SCU84, 13));
2094 ASPEED_PINCTRL_PIN(U2),
/linux-6.1.9/arch/arm64/boot/dts/ti/
Dk3-am654-base-board.dts140 AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0) /* (U2) MCU_OSPI0_DQS */
Dk3-am65-iot2050-common.dtsi177 /* (U2) MCU_OSPI0_DQS */
Dk3-j721e-common-proc-board.dts223 J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
/linux-6.1.9/Documentation/driver-api/usb/
Dpower-management.rst530 lower power state(L1 for usb2.0 devices, or U1/U2 for usb3.0 devices),
554 and U2 exit latencies have been set in the BOS
559 indicating whether or not USB3 hardware LPM U1 or U2
Ddwc3.rst211 ``U2``, ``U3``, ``SS.Disabled``, ``RX.Detect``, ``SS.Inactive``,
/linux-6.1.9/drivers/net/usb/
DKconfig184 * Buffalo LUA-U2-KTX
/linux-6.1.9/drivers/scsi/aic7xxx/
Daic7xxx.reg209 mask SOFS_ULTRA2 0x7f /* Sync offset U2 chips */
/linux-6.1.9/tools/memory-model/Documentation/
Dexplanation.txt1787 U2: rcu_read_unlock();
1791 that U0 ->rcu-rscsi L0 ->rcu-link S1 ->rcu-gp S1 ->rcu-link U2 ->rcu-rscsi