| /linux-6.1.9/arch/s390/boot/ |
| D | head_kdump.S | 31 jne .Lrelocate # No : Start data mover
32 lghi %r2,0 # Yes: Start kdump kernel
77 basr %r14,%r14 # Start relocated kernel
88 0: lpswe .Lrestart_psw-0b(%r13) # Start new kernel...
|
| /linux-6.1.9/tools/testing/selftests/media_tests/ |
| D | regression_test.txt | 21 Start media_device_test to regression test media devnode dynamic alloc
34 Start 6 open_loop_test.sh tests with different /dev/mediaX files. When
35 device file goes away after unbind, device file name changes. Start the
41 and number to run bind and unbind. Start the bind_unbind.sh
|
| /linux-6.1.9/init/ |
| D | initramfs.c | 220 Start, enumerator
442 [Start] = do_start,
474 state = Start; in flush_buffer()
503 state = Start; in unpack_to_rootfs()
509 state = Start; in unpack_to_rootfs()
|
| /linux-6.1.9/Documentation/riscv/ |
| D | vm-layout.rst | 36 Start addr | Offset | End addr | Size | VM area description
72 Start addr | Offset | End addr | Size | VM area description
|
| /linux-6.1.9/tools/perf/arch/x86/tests/ |
| D | gen-insn-x86-dat.awk | 19 / Start here / {
|
| /linux-6.1.9/Documentation/input/devices/ |
| D | iforce-protocol.rst | 203 01 Start/Stop
205 Val 01: Start and play once.
206 Val 41: Start and play n times (See byte 02 below)
365 2. Start a soft spying RS232 or USB (depending on where you connected your
|
| /linux-6.1.9/Documentation/hwmon/ |
| D | adm1177.rst | 16 Hot-Swap Controller and Digital Power Monitors with Soft Start Pin.
|
| /linux-6.1.9/arch/m68k/kernel/ |
| D | vmlinux-sun3.lds | 32 _sdata = .; /* Start of rw data section */
|
| D | vmlinux-std.lds | 32 _sdata = .; /* Start of data section */
|
| /linux-6.1.9/drivers/staging/rtl8723bs/hal/ |
| D | hal_com.c | 902 char *In, u32 *Start, char *Out, char LeftQualifier, char RightQualifier in ParseQualifiedString() argument
906 char c = In[(*Start)++]; in ParseQualifiedString()
911 i = (*Start); in ParseQualifiedString()
912 while ((c = In[(*Start)++]) != RightQualifier) in ParseQualifiedString()
914 j = (*Start) - 2; in ParseQualifiedString()
|
| /linux-6.1.9/Documentation/userspace-api/media/v4l/ |
| D | vidioc-overlay.rst | 13 VIDIOC_OVERLAY - Start or stop video overlay
|
| /linux-6.1.9/Documentation/devicetree/bindings/mfd/ |
| D | fsl-imx25-tsadc.txt | 8 - reg: Start address and size of the memory area of
|
| /linux-6.1.9/Documentation/networking/caif/ |
| D | caif.rst | 14 Start chapter
40 The use of Start-of-frame-extension (STX) must also be set as
|
| /linux-6.1.9/Documentation/driver-api/tty/ |
| D | tty_struct.rst | 47 Start & Stop
|
| /linux-6.1.9/arch/arm/boot/dts/ |
| D | imx53-qsb.dts | 10 model = "Freescale i.MX53 Quick Start Board";
|
| D | imx53-qsrb.dts | 11 model = "Freescale i.MX53 Quick Start-R Board";
|
| /linux-6.1.9/Documentation/ABI/testing/ |
| D | sysfs-block-loop | 23 (RO) Start offset (in bytes).
|
| /linux-6.1.9/Documentation/arm/ |
| D | porting.rst | 21 Start address of decompressor. There's no point in talking about
29 Start address of zero-initialised work area for the decompressor.
|
| /linux-6.1.9/drivers/staging/rtl8723bs/include/ |
| D | hal_com.h | 152 bool ParseQualifiedString(char *In, u32 *Start, char *Out, char LeftQualifier,
|
| /linux-6.1.9/drivers/gpu/drm/i810/ |
| D | i810_drv.h | 73 unsigned long Start; member
|
| /linux-6.1.9/Documentation/filesystems/ |
| D | ntfs.rst | 280 Device Boot Start End Blocks Id System
321 the "Start sector of device" when creating the table. Once again ldminfo would
329 # Offset into Size of this Raid type Device Start sector
342 # Offset Size Raid Number Chunk 1st Start 2nd Start
353 # Ofs Size Raid Log Number Region Should Number Source Start Target Start
|
| /linux-6.1.9/Documentation/devicetree/bindings/i2c/ |
| D | renesas,riic.yaml | 36 - description: Start Condition Detection Interrupt
|
| /linux-6.1.9/Documentation/firmware-guide/acpi/ |
| D | aml-debugger.rst | 37 2. Start the userspace debugger interface
|
| /linux-6.1.9/Documentation/crypto/ |
| D | crypto_engine.rst | 32 Start it via ``crypto_engine_start()``. When finished with your work, shut down the
|
| /linux-6.1.9/Documentation/devicetree/bindings/memory-controllers/ |
| D | ti,gpmc-child.yaml | 99 description: Start-cycle to first data valid delay
123 description: Start of wait monitoring with regard to valid data
|