Searched refs:SW2 (Results 1 – 25 of 28) sorted by relevance
12
| /linux-6.1.9/arch/arm/boot/dts/ |
| D | r8a7792-blanche.dts | 120 label = "SW2-1";
127 label = "SW2-2";
134 label = "SW2-3";
141 label = "SW2-4";
|
| D | sh73a0-kzm9g.dts | 113 label = "SW2-R";
119 label = "SW2-L";
125 label = "SW2-P";
131 label = "SW2-U";
137 label = "SW2-D";
|
| D | r8a7794-alt.dts | 106 label = "SW2-1";
113 label = "SW2-2";
120 label = "SW2-3";
127 label = "SW2-4";
|
| D | r8a7793-gose.dts | 76 label = "SW2-1";
83 label = "SW2-2";
90 label = "SW2-3";
97 label = "SW2-4";
|
| D | r8a7790-lager.dts | 89 label = "SW2-1";
96 label = "SW2-2";
103 label = "SW2-3";
110 label = "SW2-4";
|
| D | r8a7791-koelsch.dts | 90 label = "SW2-1";
97 label = "SW2-2";
104 label = "SW2-3";
111 label = "SW2-4";
|
| D | imx53-qsrb.dts | 51 regulator-name = "SW2";
|
| D | r7s72100-rskrza1.dts | 50 label = "SW2";
|
| D | at91-kizbox3-hs.dts | 79 label = "SW2";
|
| D | r8a7792-wheat.dts | 62 label = "SW2";
|
| D | r8a7742-iwg21d-q7-dbcm-ca.dts | 234 * Set SW2 switch on the SOM to 'ON'
|
| D | r8a7742-iwg21d-q7.dts | 311 /* SW2[6] determines which connector is activated
|
| /linux-6.1.9/Documentation/devicetree/bindings/regulator/ |
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
90 SW2 {
|
| /linux-6.1.9/drivers/regulator/ |
| D | pcap-regulator.c | 132 VREG_INFO(SW2, PCAP_REG_SWCTRL, 6, 7, NA, NA),
228 VREG(VAUX4), VREG(VSIM), VREG(VSIM2), VREG(VVIB), VREG(SW1), VREG(SW2),
|
| D | pfuze100-regulator.c | 373 PFUZE100_SW_REG(PFUZE100, SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000),
391 PFUZE100_SW_REG(PFUZE200, SW2, PFUZE100_SW2VOL, 400000, 1975000, 25000),
409 PFUZE3000_SW_REG(PFUZE3000, SW2, PFUZE100_SW2VOL, 0x7, pfuze3000_sw2lo),
424 PFUZE3000_SW_REG(PFUZE3001, SW2, PFUZE100_SW2VOL, 0x7, pfuze3000_sw2lo),
|
| D | cpcap-regulator.c | 333 CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2,
409 CPCAP_REG(SW2, CPCAP_REG_S2C1, CPCAP_REG_ASSIGN2,
|
| D | pv88060-regulator.c | 218 PV88060_SW(PV88060, SW2, 5000000),
|
| D | ltc3676.c | 226 LTC3676_LINEAR_REG(SW2, sw2, BUCK2, DVB2A),
|
| D | ltc3589.c | 258 LTC3589_LINEAR_REG(SW2, sw2, B2DTV1),
|
| /linux-6.1.9/arch/arm64/boot/dts/renesas/ |
| D | rzg2l-smarc.dtsi | 42 * SW2 should be at position 2->3 so that SER0_TX line is activated
|
| D | rzg2lc-smarc.dtsi | 84 * SW2 should be at position 2->3 so that SER0_TX line is activated
|
| /linux-6.1.9/Documentation/networking/ |
| D | arcnet-hardware.rst | 803 < | SW1 | | SW2 | |
831 SW2 1-6: Reserved for Future Use
1051 | | | SW2 |
1064 SW2: DIP-Switches for Memory Base and I/O Base addresses
1087 The I/O base address is coded with DIP-Switches 6,7 and 8 of SW2:
1104 DIP Switches 1-5 of SW2 encode the RAM and ROM Address Range:
1377 The eight switches in SW2 are used to set the node ID. Each node attached
1575 SW2 1-8: Node ID Select (ID0-ID7)
1588 The eight switches in SW2 are used to set the node ID. Each node attached
1833 | |SW2| |
[all …]
|
| /linux-6.1.9/Documentation/hid/ |
| D | hid-alps.rst | 114 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
164 Byte1 1 1 1 0 1 SW3 SW2 SW1
|
| /linux-6.1.9/include/linux/mfd/ |
| D | ezx-pcap.h | 131 #define SW2 18 macro
|
| /linux-6.1.9/Documentation/devicetree/bindings/mfd/ |
| D | mc13xxx.txt | 87 sw2 : regulator SW2 (register 25, bit 0)
|
12