| /linux-6.1.9/drivers/video/fbdev/omap/ |
| D | lcd_h3.c | 23 r = tps65010_set_gpio_out_value(GPIO1, HIGH); in h3_panel_enable()
25 r = tps65010_set_gpio_out_value(GPIO2, HIGH); in h3_panel_enable()
|
| /linux-6.1.9/Documentation/devicetree/bindings/media/i2c/ |
| D | ov7670.txt | 13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | st,st-mipid02.txt | 45 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
47 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | tvp5150.txt | 44 - hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
|
| /linux-6.1.9/Documentation/devicetree/bindings/regulator/ |
| D | gpio-regulator.yaml | 47 1: HIGH
70 description: Polarity of "enable-gpio" GPIO is active HIGH. Default is
|
| D | maxim,max8973.yaml | 40 1 for HIGH and 0 for LOW.
|
| /linux-6.1.9/arch/arm64/boot/dts/renesas/ |
| D | hihope-rzg2-ex-lvds.dtsi | 21 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
|
| /linux-6.1.9/include/linux/mfd/ |
| D | tps65010.h | 122 #define HIGH 1 macro
|
| /linux-6.1.9/arch/arm/boot/dts/ |
| D | rk3228-evb.dts | 67 rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
|
| D | imx6qdl-mba6.dtsi | 372 /* HYS = 1, DSE = 111, 100k up, SPEED = HIGH */
436 /* HYS = 1, DSE = 110, 100k up, SPEED = HIGH (11)*/
466 /* HYS = 1, DSE = 110, PUE+PKE, SPEED = HIGH (11)*/
|
| D | imx6q-bosch-acc.dts | 443 connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */
444 intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */
445 reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */
|
| D | rk3288-rock2-som.dtsi | 251 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /linux-6.1.9/Documentation/devicetree/bindings/clock/ |
| D | silabs,si5351.txt | 55 1 = clock output is driven HIGH when disabled
56 2 = clock output is FLOATING (HIGH-Z) when disabled
|
| /linux-6.1.9/drivers/s390/crypto/ |
| D | zcrypt_msgtype6.h | 108 #define HIGH 500 macro
|
| /linux-6.1.9/Documentation/devicetree/bindings/media/ |
| D | video-interfaces.yaml | 118 Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
124 Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. Note,
156 Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively.
|
| /linux-6.1.9/Documentation/userspace-api/media/cec/ |
| D | cec-ioc-dqevent.rst | 160 * .. _`CEC-EVENT-PIN-CEC-HIGH`:
176 * .. _`CEC-EVENT-PIN-HPD-HIGH`:
194 * .. _`CEC-EVENT-PIN-5V-HIGH`:
|
| /linux-6.1.9/Documentation/devicetree/bindings/thermal/ |
| D | rockchip-thermal.yaml | 67 description: The hardware-controlled active polarity 0:LOW 1:HIGH.
|
| /linux-6.1.9/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 122 GPIO1/nRST_IO pins are HIGH only if all rails
123 that have POK control enabled are HIGH.
|
| D | tps6507x.txt | 30 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
|
| /linux-6.1.9/drivers/nfc/st95hf/ |
| D | core.c | 76 #define HIGH 1 macro
454 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
466 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
|
| /linux-6.1.9/arch/arm64/boot/dts/rockchip/ |
| D | rk3368-evb.dtsi | 225 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /linux-6.1.9/Documentation/leds/ |
| D | leds-lm3556.rst | 24 or by pulling the STROBE pin HIGH.
|
| /linux-6.1.9/Documentation/devicetree/bindings/memory-controllers/ddr/ |
| D | jedec,lpddr3-timings.yaml | 36 CKE minimum pulse width (HIGH and LOW pulse width) in pico seconds.
|
| /linux-6.1.9/drivers/net/ieee802154/ |
| D | cc2520.c | 26 #define HIGH 1 macro
1171 gpio_set_value(pdata.vreg, HIGH); in cc2520_probe()
1174 gpio_set_value(pdata.reset, HIGH); in cc2520_probe()
|
| /linux-6.1.9/Documentation/driver-api/iio/ |
| D | buffers.rst | 62 |D11|D10|D9 |D8 |D7 |D6 |D5 |D4 | (HIGH byte, address 0x07)
|