/linux-6.1.9/Documentation/networking/devlink/ |
D | devlink-params.rst | 59 - Boolean 62 - Boolean 98 - Boolean 101 - Boolean 105 - Boolean 109 - Boolean 113 - Boolean 116 - Boolean 126 - Boolean 129 - Boolean
|
D | ti-cpsw-switch.rst | 24 - Boolean 29 - Boolean
|
D | mlx4.rst | 35 - Boolean 39 - Boolean
|
D | am65-nuss-cpsw-switch.rst | 24 - Boolean
|
D | qed.rst | 23 - Boolean
|
/linux-6.1.9/Documentation/devicetree/bindings/regulator/ |
D | nvidia,tegra-regulators-coupling.txt | 24 - nvidia,tegra-core-regulator: Boolean property that designates regulator 26 - nvidia,tegra-rtc-regulator: Boolean property that designates regulator 28 - nvidia,tegra-cpu-regulator: Boolean property that designates regulator
|
/linux-6.1.9/Documentation/devicetree/bindings/sound/ |
D | da7218.txt | 48 - dlg,hp-diff-single-supply : Boolean flag, use single supply for HP 62 - dlg,comp-inv : Boolean flag, invert comparator output 63 - dlg,hyst : Boolean flag, enable hysteresis 64 - dlg,discharge : Boolean flag, auto discharge of Mic Bias on jack removal
|
D | rt5660.txt | 18 Boolean. Indicate MIC1/3 input are differential, rather than single-ended. 21 Boolean. If the codec will be powered off in suspend, the resume should be
|
D | cs35l35.txt | 23 - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a 34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal 37 - cirrus,external-boost : Boolean to specify the device is using an external 51 - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control 66 - cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change 85 - cirrus,classh-bst-overide : Boolean
|
D | cs35l36.txt | 32 - cirrus,multi-amp-mode : Boolean to determine if there are more than 43 - cirrus,amp-pcm-inv : Boolean to determine Amplifier will invert incoming 46 - cirrus,imon-pol-inv : Boolean to determine Amplifier will invert the 49 - cirrus,vmon-pol-inv : Boolean to determine Amplifier will invert the 56 - cirrus,weak-fet-disable : Boolean : The strength of the output drivers is
|
D | rt5651.txt | 14 Boolean. Indicate MIC2 input are differential, rather than single-ended. 17 Boolean. true if dmic is used.
|
D | cirrus,cs35l41.yaml | 93 Boolean which specifies whether the GPIO1 99 Boolean which specifies whether the GPIO1 pin 118 Boolean which specifies whether the GPIO2 124 Boolean which specifies whether the GPIO2 pin
|
D | cs43130.txt | 29 Boolean, define to enable headphone DC impedance measurement. 32 Boolean, define to enable headphone AC impedance measurement.
|
D | cs35l34.txt | 41 - cirrus,gain-zc-disable: Boolean property. If set, the gain change will take 44 - cirrus,tdm-rising-edge: Boolean property. If set, data is on the rising edge of
|
/linux-6.1.9/scripts/ |
D | generate_rust_target.rs | 20 Boolean(bool), enumerator 33 Value::Boolean(boolean) => write!(formatter, "{}", boolean), in fmt() 64 self.0.push((key.to_string(), Value::Boolean(value))); in push()
|
/linux-6.1.9/Documentation/devicetree/bindings/iio/temperature/ |
D | adi,ltc2983.yaml | 99 Boolean property which set's the thermocouple as single-ended. 142 description: Boolean property which set's the diode as single-ended. 147 Boolean property which set's three conversion cycles removing 153 Boolean property which enables a running average of the diode 213 Boolean property which enables Rsense sharing, where one sense 219 Boolean property which enables excitation current rotation to 287 Boolean property which set's the thermistor as single-ended. 292 Boolean property which enables Rsense sharing, where one sense 299 Boolean property which enables excitation current rotation to 353 description: Boolean property which set's the adc as single-ended.
|
/linux-6.1.9/Documentation/devicetree/bindings/ |
D | common-properties.txt | 13 - big-endian: Boolean; force big endian register accesses 16 - little-endian: Boolean; force little endian register accesses 19 - native-endian: Boolean; always use register accesses matched to the
|
/linux-6.1.9/Documentation/devicetree/bindings/gpio/ |
D | gpio-max3191x.txt | 30 - maxim,modesel-8bit: Boolean whether the modesel pin of the chips is 37 Boolean whether to ignore undervoltage alarms signaled
|
/linux-6.1.9/Documentation/devicetree/bindings/leds/ |
D | leds-bcm6358.txt | 18 - brcm,clk-dat-low : Boolean, makes clock and data signals active low. 28 - active-low : Boolean, makes LED active low.
|
/linux-6.1.9/Documentation/devicetree/bindings/mfd/ |
D | as3722.txt | 18 - ams,enable-internal-int-pullup: Boolean property, to enable internal pullup on 20 - ams,enable-internal-i2c-pullup: Boolean property, to enable internal pullup on 23 - ams,enable-ac-ok-power-on: Boolean property, to enable exit out of power off 130 ams,system-power-controller: Boolean, to enable the power off functionality
|
/linux-6.1.9/Documentation/ABI/testing/ |
D | sysfs-class-net-qmi | 6 Boolean. Default: 'N' 67 Boolean. Default: 'N'
|
/linux-6.1.9/Documentation/devicetree/bindings/pinctrl/ |
D | lantiq,pinctrl-falcon.txt | 56 - lantiq,drive-current: Boolean, enables drive-current 57 - lantiq,slew-rate: Boolean, enables slew-rate
|
/linux-6.1.9/Documentation/devicetree/bindings/display/ |
D | fsl,dcu.txt | 14 - big-endian Boolean property, LS1021A DCU registers are big-endian.
|
/linux-6.1.9/Documentation/devicetree/bindings/usb/ |
D | atmel-usb.txt | 112 - atmel,can-dma: Boolean to specify if the endpoint support DMA. 113 - atmel,can-isoc: Boolean to specify if the endpoint support ISOC.
|
/linux-6.1.9/drivers/staging/media/deprecated/saa7146/av7110/ |
D | video-stop.rst | 45 - Boolean mode
|