Searched refs:BTN_0 (Results 1 – 25 of 103) sorted by relevance
12345
| /linux-6.1.9/drivers/input/joystick/ |
| D | spaceball.c | 223 input_dev->keybit[BIT_WORD(BTN_0)] |= BIT_MASK(BTN_9); in spaceball_connect()
229 input_dev->keybit[BIT_WORD(BTN_0)] |= BIT_MASK(BTN_2) | in spaceball_connect()
235 input_dev->keybit[BIT_WORD(BTN_0)] |= BIT_MASK(BTN_1) | in spaceball_connect()
|
| D | fsia6b.c | 68 int sw_id = BTN_0; in fsia6b_serio_irq()
176 input_set_capability(input_dev, EV_KEY, BTN_0 + sw_id); in fsia6b_serio_connect()
|
| D | n64joy.c | 177 input_report_key(dev, BTN_0, data[i].a); in n64joy_poll()
302 input_set_capability(dev, EV_KEY, BTN_0); in n64joy_probe()
|
| /linux-6.1.9/arch/mips/bcm47xx/ |
| D | buttons.c | 39 BCM47XX_GPIO_KEY(4, BTN_0), /* Router mode */
150 BCM47XX_GPIO_KEY(5, BTN_0), /* Router / AP mode swtich */
157 BCM47XX_GPIO_KEY(5, BTN_0), /* Router / AP mode swtich */
164 BCM47XX_GPIO_KEY(5, BTN_0), /* Router / AP mode swtich */
|
| /linux-6.1.9/drivers/media/rc/keymaps/ |
| D | rc-imon-rsc.c | 40 { 0x801098, BTN_0 },
|
| /linux-6.1.9/drivers/input/misc/ |
| D | powermate.c | 110 input_report_key(pm->input, BTN_0, pm->data[0] & 0x01); in powermate_irq()
371 input_dev->keybit[BIT_WORD(BTN_0)] = BIT_MASK(BTN_0); in powermate_probe()
|
| D | rb532_button.c | 19 #define RB532_BTN_KSYM BTN_0
|
| /linux-6.1.9/drivers/input/tablet/ |
| D | hanwang.c | 97 BTN_0, BTN_1, BTN_2, BTN_3, BTN_4, BTN_5, BTN_6, BTN_7, BTN_8,
209 input_report_key(input_dev, BTN_0, data[2]); in hanwang_parse_packet()
223 input_report_key(input_dev, BTN_0, data[5] & 0x01); in hanwang_parse_packet()
|
| /linux-6.1.9/drivers/hid/ |
| D | hid-letsketch.c | 139 input_set_capability(input, EV_KEY, BTN_0 + i); in letsketch_setup_input_tablet_pad()
198 input_report_key(input, BTN_0 + i, raw_data[4] == (i + 1)); in letsketch_raw_event()
|
| /linux-6.1.9/arch/arm/boot/dts/ |
| D | omap3-overo-palo43-common.dtsi | 39 linux,code = <BTN_0>;
|
| D | omap3-overo-gallop43-common.dtsi | 39 linux,code = <BTN_0>;
|
| D | omap3-overo-palo35-common.dtsi | 39 linux,code = <BTN_0>;
|
| D | socfpga_cyclone5_vining_fpga.dts | 38 label = "BTN_0"; /* TEMP_OS */
40 linux,code = <BTN_0>;
|
| D | omap3-overo-chestnut43-common.dtsi | 39 linux,code = <BTN_0>;
|
| D | armada-388-clearfog-base.dts | 27 linux,code = <BTN_0>;
|
| D | omap3-overo-alto35-common.dtsi | 46 linux,code = <BTN_0>;
|
| D | sun8i-h3-mapleboard-mp130.dts | 53 linux,code = <BTN_0>;
|
| D | bcm4709-buffalo-wxr-1900dhp.dts | 109 linux,code = <BTN_0>;
|
| D | bcm47094-dlink-dir-885l.dts | 98 linux,code = <BTN_0>;
|
| /linux-6.1.9/arch/sh/boards/mach-rsk/ |
| D | devices-rsk7203.c | 88 .code = BTN_0,
|
| /linux-6.1.9/Documentation/devicetree/bindings/input/ |
| D | atmel,captouch.txt | 31 linux,keycodes = <BTN_0>, <BTN_1>,
|
| /linux-6.1.9/drivers/mfd/ |
| D | ucb1x00-assabet.c | 49 buttons[i].code = BTN_0 + i; in ucb1x00_assabet_add()
|
| /linux-6.1.9/arch/mips/boot/dts/qca/ |
| D | ar9331_tl_mr3020.dts | 61 linux,code = <BTN_0>;
|
| /linux-6.1.9/Documentation/input/ |
| D | input-programming.rst | 23 input_report_key(button_dev, BTN_0, inb(BUTTON_PORT) & 1);
45 button_dev->keybit[BIT_WORD(BTN_0)] = BIT_MASK(BTN_0);
85 type events, and from those only BTN_0 event code. Thus we only set these
89 set_bit(BTN_0, button_dev->keybit);
|
| /linux-6.1.9/arch/mips/alchemy/ |
| D | board-mtx1.c | 86 .code = BTN_0,
|
12345