| /linux-5.19.10/Documentation/devicetree/bindings/mfd/ |
| D | mxs-lradc.txt | 10 - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
13 disabled. 5 wires is valid for i.MX28 SoC only.
29 fsl,lradc-touchscreen-wires = <4>;
41 fsl,lradc-touchscreen-wires = <5>;
|
| /linux-5.19.10/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-temperature-max31856 | 6 such as those caused by broken thermocouple wires.
10 '1' An open circuit such as broken thermocouple wires
12 '0' No open circuit or broken thermocouple wires are detected
|
| /linux-5.19.10/Documentation/devicetree/bindings/input/touchscreen/ |
| D | ti,am3359-tsc.yaml | 16 ti,wires:
38 wires on touchscreen. We need to provide an 8-bit number where the
60 - ti,wires
71 ti,wires = <4>;
|
| D | fsl-mx25-tcq.txt | 11 - fsl,wires: Should be '<4>' or '<5>'
33 fsl,wires = <4>;
|
| /linux-5.19.10/drivers/input/touchscreen/ |
| D | ti_am335x_tsc.c | 52 unsigned int wires; member
136 switch (ts_dev->wires) { in titsc_step_config()
165 switch (ts_dev->wires) { in titsc_step_config()
358 err = of_property_read_u32(node, "ti,wires", &ts_dev->wires); in titsc_parse_dt()
361 switch (ts_dev->wires) { in titsc_parse_dt()
|
| D | fsl-imx25-tcq.c | 436 u32 wires; in mx25_tcq_parse_dt() local
445 error = of_property_read_u32(np, "fsl,wires", &wires); in mx25_tcq_parse_dt()
451 if (wires == 4) { in mx25_tcq_parse_dt()
454 dev_err(&pdev->dev, "%u-wire mode not supported\n", wires); in mx25_tcq_parse_dt()
|
| /linux-5.19.10/Documentation/devicetree/bindings/sound/ |
| D | mt6359.yaml | 24 signal. 0 means two wires, 1 means one wire. Default value is 0.
27 - 1 # two wires
|
| D | mt6358.txt | 15 channels of PDM signal. 0 means two wires, 1 means one wire. Default
|
| /linux-5.19.10/include/linux/platform_data/ |
| D | mmc-davinci.h | 20 u8 wires; member
|
| D | mmc-omap.h | 46 u8 wires; /* Used for the MMC driver on omap1 and 2420 */ member
|
| /linux-5.19.10/Documentation/devicetree/bindings/display/tilcdc/ |
| D | tilcdc.txt | 25 - "crossed" indicates wiring that has blue and red wires
44 the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]),
|
| /linux-5.19.10/Documentation/devicetree/bindings/iio/adc/ |
| D | atmel,sama9260-adc.yaml | 70 atmel,adc-ts-wires:
73 Number of touchscreen wires. Must be set to enable touchscreen.
|
| /linux-5.19.10/arch/arm/boot/dts/ |
| D | sama5d3xdm.dtsi | 25 atmel,adc-ts-wires = <4>;
|
| D | at91-cosino_mega2560.dts | 23 atmel,adc-ts-wires = <4>;
|
| D | at91sam9x5dm.dtsi | 58 atmel,adc-ts-wires = <4>;
|
| D | imx6ul-ccimx6ulsbcpro.dts | 385 pinctrl_uart2_4wires: uart2grp-4wires {
394 pinctrl_uart3_2wires: uart3grp-2wires {
|
| D | imx23-evk.dts | 105 fsl,lradc-touchscreen-wires = <4>;
|
| /linux-5.19.10/arch/arm/mach-omap1/ |
| D | devices.c | 91 if (mmc_controller->slots[0].wires == 4 && !cpu_is_omap7xx()) { in omap1_mmc_mux()
107 if (mmc_controller->slots[1].wires == 4) { in omap1_mmc_mux()
|
| /linux-5.19.10/drivers/gpu/drm/amd/acp/ |
| D | Kconfig | 12 This adds the ACP (Audio CoProcessor) IP driver and wires
|
| /linux-5.19.10/Documentation/devicetree/bindings/clock/ |
| D | arm,syscon-icst.yaml | 25 connects the low 8 bits of the VDW (missing one bit), hard-wires RDW to
26 different values and sometimes also hard-wires the output divider. They
|
| /linux-5.19.10/Documentation/devicetree/bindings/iio/temperature/ |
| D | maxim,max31865.yaml | 24 Identifies the number of wires used by the RTD. Setting this property
|
| D | adi,ltc2983.yaml | 204 adi,number-of-wires:
206 Identifies the number of wires used by the RTD. Setting this
207 property to 5 means 4 wires with Kelvin Rsense.
426 adi,number-of-wires = <2>;
|
| /linux-5.19.10/Documentation/devicetree/bindings/media/i2c/ |
| D | aptina,mt9v111.yaml | 17 of image resolutions and formats controllable through a simple two-wires
|
| /linux-5.19.10/arch/arm/mach-davinci/ |
| D | board-neuros-osd2.c | 163 .wires = 4,
|
| /linux-5.19.10/Documentation/driver-api/gpio/ |
| D | drivers-on-gpio.rst | 26 mouse cable and connect the wires to GPIO lines or solder a mouse connector
49 (two wires, SDA and SCL lines) by hammering (bitbang) two GPIO lines. It will
54 of wires, at least SCK and optionally MISO, MOSI and chip select lines) using
|