Home
last modified time | relevance | path

Searched refs:tied (Results 1 – 25 of 52) sorted by relevance

123

/linux-5.19.10/Documentation/security/
Dlandlock.rst51 All access rights are tied to an inode and what can be accessed through it.
58 to be tied to files but only to directories.
84 A domain is a read-only ruleset tied to a set of subjects (i.e. tasks'
87 domain. Indeed, once in a domain, each rule is tied to a layer level. To
/linux-5.19.10/Documentation/devicetree/bindings/soc/qcom/
Dqcom,smd.yaml72 In turn, subnodes of the "edges" represent devices tied to SMD
83 A list of channels tied to this device, used for matching the
111 # "rpm" subsystem. For the "rpm" subsystem we have a device tied to the
Dqcom,glink.txt41 Each subnode of the GLINK node represent function tied to a virtual
49 Definition: a list of channels tied to this function, used for matching
/linux-5.19.10/drivers/gpu/drm/nouveau/nvkm/engine/disp/
Dvga.c166 u32 tied = nvkm_rd32(device, 0x001084) & 0x10000000; in nvkm_rdvgaowner() local
167 if (tied == 0) { in nvkm_rdvgaowner()
/linux-5.19.10/Documentation/devicetree/bindings/iio/adc/
Dti,ads8688.yaml26 REFSEL input tied low to enable the internal reference.
Dadi,ad7606.yaml78 this pin is tied to a logic high, the analog input range is ±10V for
79 all channels. If this pin is tied to a logic low, the analog input range
/linux-5.19.10/Documentation/spi/
Dspi-lm70llp.rst66 collector is tied to VCC.
72 hand, the transistor is cut off and the voltage tied to it's collector is
/linux-5.19.10/Documentation/driver-api/nvdimm/
Dsecurity.rst93 An key with the current passphrase payload that is tied to the nvdimm should be
101 An key with the current passphrase payload that is tied to the nvdimm should be
115 An encrypted-key with the current user passphrase that is tied to the nvdimm
/linux-5.19.10/security/landlock/
DKconfig12 directory, etc.) tied to a file hierarchy. Such policy can be
/linux-5.19.10/Documentation/devicetree/bindings/mmc/
Dsdhci-atmel.txt20 For instance on SAMA5D2, the pin is usually tied to the GND with a resistor
/linux-5.19.10/Documentation/devicetree/bindings/mfd/
Drichtek,rt4831.yaml36 Some usage directly tied this pin to follow VIO 1.8V power on sequence.
Daspeed-lpc.yaml100 The UARTs present in the ASPEED SoC can have their resets tied to the reset
/linux-5.19.10/drivers/net/wireless/microchip/wilc1000/
DKconfig37 immediately following reset when pin 9 (SDIO_SPI_CFG) is tied to
/linux-5.19.10/Documentation/userspace-api/media/v4l/
Dpixfmt-meta-intel-ipu3.rst50 Both 3A statistics and pipeline parameters described here are closely tied to
/linux-5.19.10/arch/arm64/boot/dts/rockchip/
Drk3566-soquartz-cm4.dts46 * the rtc interrupt is tied to PMIC_PWRON,
/linux-5.19.10/arch/powerpc/boot/dts/
Dxpedite5200.dts431 cle-line = <0x8>; /* CLE tied to A3 */
432 ale-line = <0x10>; /* ALE tied to A4 */
Dxpedite5200_xmon.dts435 cle-line = <0x8>; /* CLE tied to A3 */
436 ale-line = <0x10>; /* ALE tied to A4 */
/linux-5.19.10/Documentation/driver-api/media/drivers/
Dcx88-devel.rst66 GPIO 16(I believe) is tied to the IR port (if present).
/linux-5.19.10/Documentation/devicetree/bindings/spi/
Dspi-davinci.txt23 lines can be tied to the interrupt controller. Set this
/linux-5.19.10/arch/arm/boot/dts/
Darmada-388-clearfog.dtsi193 * address pins tied low, which takes addresses 0x50 and 0x51.
Dsun7i-a20-bananapi-m1-plus.dts262 /* VBUS on usb host ports are tied to DC5V and therefore always on */
/linux-5.19.10/Documentation/fb/
Dep93xx-fb.rst127 the VIDSCRNPAGE (framebuffer physical offset) to be tied low. There is
/linux-5.19.10/drivers/clk/samsung/
DKconfig94 status of the certains clocks from SoC, but it could also be tied to
/linux-5.19.10/Documentation/networking/device_drivers/ethernet/pensando/
Dionic.rst93 reflects the rx-usecs value as they are tied together on the same interrupt.
/linux-5.19.10/Documentation/virt/kvm/arm/
Dhypercalls.rst13 is tied to a particular version of a hypercall service, or if a migration

123