| /linux-5.19.10/drivers/rtc/ |
| D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| D | rtc-ds1305.c | 386 char *resistors = ""; in ds1305_proc() local
402 resistors = "2k Ohm"; in ds1305_proc()
405 resistors = "4k Ohm"; in ds1305_proc()
408 resistors = "8k Ohm"; in ds1305_proc()
417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
|
| /linux-5.19.10/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /linux-5.19.10/Documentation/devicetree/bindings/leds/ |
| D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
|
| /linux-5.19.10/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /linux-5.19.10/Documentation/hwmon/ |
| D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
| D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| D | ltc4261.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| D | ltc2945.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| D | ltc4245.rst | 49 rely on the sense resistors listed in Table 2: "Sense Resistor Values".
|
| D | vt1211.rst | 84 external scaling resistors. This external scaling needs to be compensated for
89 The board level scaling resistors according to VIA's recommendation are as
|
| /linux-5.19.10/Documentation/devicetree/bindings/hwmon/ |
| D | ntc-thermistor.yaml | 13 Thermistors with negative temperature coefficient (NTC) are resistors that
60 We can use both pull-up and pull-down resistors at the same time, and then
|
| /linux-5.19.10/Documentation/devicetree/bindings/pinctrl/ |
| D | mediatek,mt6779-pinctrl.yaml | 116 Pull up setings for 2 pull resistors, R0 and R1. User can
127 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,mt6797-pinctrl.yaml | 109 Pull up setings for 2 pull resistors, R0 and R1. User can
120 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,pinctrl-mt6795.yaml | 131 Pull up setings for 2 pull resistors, R0 and R1. User can
142 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,mt8183-pinctrl.yaml | 141 Pull up setings for 2 pull resistors, R0 and R1. User can
152 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| D | mediatek,mt7986-pinctrl.yaml | 297 Pull up setings for 2 pull resistors, R0 and R1. Valid arguments
309 Pull down setings for 2 pull resistors, R0 and R1. Valid arguments
|
| D | mediatek,mt65xx-pinctrl.yaml | 100 settings for 2 pull resistors, R0 and R1. User can configure those
|
| /linux-5.19.10/Documentation/devicetree/bindings/gpio/ |
| D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|
| /linux-5.19.10/Documentation/devicetree/bindings/iio/imu/ |
| D | st,lsm6dsx.yaml | 66 description: enable/disable internal i2c controller pullup resistors.
|
| /linux-5.19.10/Documentation/ABI/stable/ |
| D | sysfs-class-udc | 63 Allows users to disconnect data pullup resistors thus causing a
|
| /linux-5.19.10/arch/arm/mach-s3c/ |
| D | Kconfig.s3c64xx | 210 resistors fitted so that the card detects for
219 resistors fitted so that the card detects for
|
| /linux-5.19.10/Documentation/devicetree/bindings/mfd/ |
| D | gateworks-gsc.yaml | 91 description: Values of resistors for divider on raw ADC input
|
| /linux-5.19.10/arch/arm/boot/dts/ |
| D | sun6i-a31s-yones-toptech-bs1078-v2.dts | 165 /* Voltage source for I2C pullup resistors for I2C Bus 0 */
|