Searched refs:driven (Results 1 – 25 of 185) sorted by relevance
12345678
| /linux-5.19.10/Documentation/devicetree/bindings/display/ |
| D | truly,nt35597.txt | 20 - ports: This device has two video ports driven by two DSIs. Their connections
23 - port@0: DSI input port driven by master DSI
24 - port@1: DSI input port driven by secondary DSI
|
| /linux-5.19.10/Documentation/devicetree/bindings/power/reset/ |
| D | gpio-restart.yaml | 17 'open-source' is not found, the GPIO line will be driven in the inactive state. Otherwise its
18 not driven until the restart is initiated.
21 is configured as an output, and driven active, triggering a level triggered reset condition.
25 inactive-delay, the GPIO is driven active again. After a delay specified by wait-delay, the
|
| /linux-5.19.10/arch/arm64/boot/dts/freescale/ |
| D | imx8mm-venice-gw72xx-0x-rs422.dts | 7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven low (in-active)
|
| D | imx8mm-venice-gw72xx-0x-rs485.dts | 7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven high (active)
|
| D | imx8mm-venice-gw73xx-0x-rs422.dts | 7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven low (in-active)
|
| D | imx8mm-venice-gw73xx-0x-rs485.dts | 7 * - GPIO4_0 rs485_en needs to be driven high (active)
8 * - GPIO4_2 rs485_hd needs to be driven high (active)
|
| /linux-5.19.10/drivers/leds/rgb/ |
| D | Kconfig | 6 tristate "PWM driven multi-color LED Support"
9 This option enables support for PWM driven monochrome LEDs that are
|
| /linux-5.19.10/Documentation/hwmon/ |
| D | tc654.rst | 32 Setting pwm1_mode to 1 will cause the pwm output to be driven based on
34 driven based on the Vin input.
|
| /linux-5.19.10/Documentation/devicetree/bindings/mfd/ |
| D | st,stm32-timers.yaml | 11 - advanced-control timers consist of a 16-bit auto-reload counter driven
15 driven by a programmable prescaler and PWM outputs.
16 - basic timers consist of a 16-bit auto-reload counter driven by a
|
| /linux-5.19.10/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe/ |
| D | pincfg.txt | 18 0 = The pin is actively driven as an output
20 driven active-low, otherwise it is three-stated.
|
| /linux-5.19.10/Documentation/driver-api/thermal/ |
| D | nouveau_thermal.rst | 75 Your fan can be driven in different modes:
78 * 1: The fan can be driven in manual (use pwm1 to change the speed);
79 * 2; The fan is driven automatically depending on the temperature.
|
| /linux-5.19.10/Documentation/devicetree/bindings/input/ |
| D | gpio-matrix-keypad.txt | 1 * GPIO driven matrix keypad device tree bindings
3 GPIO driven matrix keypad is used to interface a SoC with a matrix keypad.
|
| /linux-5.19.10/Documentation/devicetree/bindings/pinctrl/ |
| D | renesas,rza1-ports.yaml | 82 "software IO driven" mode to be specified. To do so use the generic
89 controller driver internally, while software driven IO direction has to
174 * Configure TIOC0A as software driven input
184 * Configure TIOC0B as software driven output
|
| D | marvell,dove-pinctrl.txt | 64 pmu-nc Pin not driven by any PM function
65 pmu-low Pin driven low (0)
66 pmu-high Pin driven high (1)
|
| /linux-5.19.10/Documentation/peci/ |
| D | peci.rst | 30 bit with a driven, rising edge from an idle near zero volts. The
31 duration of the signal driven high allows to determine whether the bit
|
| /linux-5.19.10/Documentation/sound/soc/ |
| D | clocking.rst | 12 Every audio subsystem is driven by a master clock (sometimes referred to as MCLK
24 The Digital Audio Interface is usually driven by a Bit Clock (often referred to
|
| /linux-5.19.10/Documentation/networking/ |
| D | team.rst | 7 Team devices are driven from userspace via libteam library which is here:
|
| /linux-5.19.10/Documentation/devicetree/bindings/nvmem/ |
| D | nvmem.yaml | 37 The write-protect GPIO is asserted, when it's driven high
39 when it's driven low (logical '0') to allow writing.
|
| /linux-5.19.10/Documentation/devicetree/bindings/display/panel/ |
| D | sharp,lq101r1sx01.yaml | 18 driven by the first link (DSI-LINK1), left or even, is considered the primary
20 to the peripheral driven by the second link (DSI-LINK2, right or odd).
|
| D | panel-dsi-cm.yaml | 15 are usually driven in command mode. If no backlight is
45 because all its power rails can be driven by the same supply. In that case
|
| /linux-5.19.10/Documentation/devicetree/bindings/gpio/ |
| D | nxp,pcf8575.yaml | 14 driven high by a pull-up current source or driven low to ground. This
|
| /linux-5.19.10/drivers/parport/ |
| D | BUGS-parport | 7 software-driven mode in ieee1284_ops.c
|
| /linux-5.19.10/Documentation/features/debug/stackprotector/ |
| D | arch-support.txt | 4 # description: arch supports compiler driven stack overflow protection
|
| /linux-5.19.10/Documentation/ABI/testing/ |
| D | sysfs-driver-fsi-master-gpio | 9 where the FSI bus is driven externally (for example, by
|
| /linux-5.19.10/Documentation/driver-api/gpio/ |
| D | intro.rst | 49 options about how that value is driven, so that for example only one
50 value might be driven, supporting "wire-OR" and similar schemes for the
95 level is actually driven), or "open source" (where only the high signal level is
96 driven) signaling. That term applies to CMOS transistors; "open collector" is
|
12345678