| /linux-5.19.10/tools/build/feature/ |
| D | test-libunwind-aarch64.c | 13 static unw_accessors_t accessors; variable
19 addr_space = unw_create_addr_space(&accessors, 0); in main()
|
| D | test-libunwind-arm.c | 14 static unw_accessors_t accessors; variable
20 addr_space = unw_create_addr_space(&accessors, 0); in main()
|
| D | test-libunwind-x86.c | 14 static unw_accessors_t accessors; variable
20 addr_space = unw_create_addr_space(&accessors, 0); in main()
|
| D | test-libunwind-x86_64.c | 14 static unw_accessors_t accessors; variable
20 addr_space = unw_create_addr_space(&accessors, 0); in main()
|
| D | test-libunwind.c | 14 static unw_accessors_t accessors; variable
20 addr_space = unw_create_addr_space(&accessors, 0); in main()
|
| /linux-5.19.10/drivers/soc/litex/ |
| D | Kconfig | 16 accessors.
|
| /linux-5.19.10/arch/arm/common/ |
| D | Makefile | 10 obj-$(CONFIG_KRAIT_L2_ACCESSORS) += krait-l2-accessors.o
|
| /linux-5.19.10/Documentation/devicetree/bindings/soc/litex/ |
| D | litex,soc-controller.yaml | 14 and to check if those accessors are ready to be used.
|
| /linux-5.19.10/drivers/soc/qcom/ |
| D | Makefile | 30 obj-$(CONFIG_QCOM_KRYO_L2_ACCESSORS) += kryo-l2-accessors.o
|
| /linux-5.19.10/Documentation/driver-api/ |
| D | device-io.rst | 171 These are the most generic accessors, providing serialization against other
183 DMA, these "relaxed" versions of the MMIO accessors only serialize against
225 accessed first, a helper is provided for each combination of 64-bit accessors
235 These are low-level MMIO accessors without barriers or byteorder changes and
249 architectures, these are mapped to readl()/writel() style accessors
266 There are no direct 64-bit I/O port accessors, but pci_iomap() in combination
272 accessors add a small delay. On architectures that do not have ISA buses,
283 MMIO accessors, these do not perform a byteswap on big-endian kernels, so the
317 writes. This may or may not be enforced when using __raw I/O accessors or
493 used together with ioread32()/iowrite32() and similar accessors
|
| /linux-5.19.10/drivers/net/mdio/ |
| D | Kconfig | 27 FWNODE MDIO bus (Ethernet PHY) accessors
35 OpenFirmware MDIO bus (Ethernet PHY) accessors
42 ACPI MDIO bus (Ethernet PHY) accessors
|
| /linux-5.19.10/Documentation/core-api/ |
| D | timekeeping.rst | 1 ktime accessors
175 some drivers may actually want the higher resolution accessors
|
| D | assoc_array.rst | 249 The caller should lock exclusively against other modifiers and accessors
|
| /linux-5.19.10/tools/perf/util/ |
| D | unwind-libunwind-local.c | 655 static unw_accessors_t accessors = { variable
668 maps->addr_space = unw_create_addr_space(&accessors, 0); in _unwind__prepare_access()
|
| /linux-5.19.10/Documentation/driver-api/gpio/ |
| D | consumer.rst | 245 To access such GPIOs, a different set of accessors is defined::
251 IRQ handler, and those accessors must be used instead of spinlock-safe
252 accessors without the cansleep() name suffix.
254 Other than the fact that these accessors might sleep, and will work on GPIOs
|
| D | legacy.rst | 210 To access such GPIOs, a different set of accessors is defined::
220 a threaded IRQ handler, and those accessors must be used instead of
221 spinlock-safe accessors without the cansleep() name suffix.
223 Other than the fact that these accessors might sleep, and will work
|
| /linux-5.19.10/Documentation/devicetree/bindings/pci/ |
| D | host-generic-pci.yaml | 77 it requires special config space accessors that filter accesses to
|
| /linux-5.19.10/Documentation/process/ |
| D | volatile-considered-harmful.rst | 58 architectures. Those accessors are written to prevent unwanted
|
| /linux-5.19.10/lib/ |
| D | Kconfig | 100 I/O accessors.
111 emulated iomem accessors.
|
| /linux-5.19.10/drivers/gpio/ |
| D | TODO | 48 numberspace accessors from <linux/gpio.h> and eventually delete
|
| /linux-5.19.10/drivers/mtd/maps/ |
| D | Kconfig | 87 platforms, some detection and setting up ROMs-specific accessors.
|
| /linux-5.19.10/Documentation/ |
| D | memory-barriers.txt | 1935 relaxed I/O accessors and the Documentation/core-api/dma-api.rst file for
2541 The readX() and writeX() MMIO accessors take a pointer to the
2601 The readsX() and writesX() MMIO accessors are designed for accessing
2608 The inX() and outX() accessors are intended to access legacy port-mapped
2626 As above, the insX() and outsX() accessors provide the same ordering
2635 With the exception of the string accessors (insX(), outsX(), readsX() and
|
| /linux-5.19.10/LICENSES/preferred/ |
| D | LGPL-2.0 | 257 layouts and accessors, and small macros and small inline functions (ten
|
| D | LGPL-2.1 | 269 layouts and accessors, and small macros and small inline functions (ten
|
| /linux-5.19.10/drivers/mmc/host/ |
| D | Kconfig | 76 need to overwrite SDHCI IO memory accessors.
|