1 // SPDX-License-Identifier: GPL-2.0
2 /*
3  * Meson AXG MIPI DPHY driver
4  *
5  * Copyright (C) 2018 Amlogic, Inc. All rights reserved
6  * Copyright (C) 2020 BayLibre, SAS
7  * Author: Neil Armstrong <narmstrong@baylibre.com>
8  */
9 
10 #include <linux/bitfield.h>
11 #include <linux/bitops.h>
12 #include <linux/bits.h>
13 #include <linux/clk.h>
14 #include <linux/delay.h>
15 #include <linux/io.h>
16 #include <linux/module.h>
17 #include <linux/of_device.h>
18 #include <linux/regmap.h>
19 #include <linux/reset.h>
20 #include <linux/phy/phy.h>
21 #include <linux/platform_device.h>
22 
23 /* [31] soft reset for the phy.
24  *		1: reset. 0: dessert the reset.
25  * [30] clock lane soft reset.
26  * [29] data byte lane 3 soft reset.
27  * [28] data byte lane 2 soft reset.
28  * [27] data byte lane 1 soft reset.
29  * [26] data byte lane 0 soft reset.
30  * [25] mipi dsi pll clock selection.
31  *		1:  clock from fixed 850Mhz clock source. 0: from VID2 PLL.
32  * [12] mipi HSbyteclk enable.
33  * [11] mipi divider clk selection.
34  *		1: select the mipi DDRCLKHS from clock divider.
35  *		0: from PLL clock.
36  * [10] mipi clock divider control.
37  *		1: /4. 0: /2.
38  * [9]  mipi divider output enable.
39  * [8]  mipi divider counter enable.
40  * [7]  PLL clock enable.
41  * [5]  LPDT data endian.
42  *		1 = transfer the high bit first. 0 : transfer the low bit first.
43  * [4]  HS data endian.
44  * [3]  force data byte lane in stop mode.
45  * [2]  force data byte lane 0 in receiver mode.
46  * [1]  write 1 to sync the txclkesc input. the internal logic have to
47  *	use txclkesc to decide Txvalid and Txready.
48  * [0]  enalbe the MIPI DPHY TxDDRClk.
49  */
50 #define MIPI_DSI_PHY_CTRL				0x0
51 
52 /* [31] clk lane tx_hs_en control selection.
53  *		1: from register. 0: use clk lane state machine.
54  * [30] register bit for clock lane tx_hs_en.
55  * [29] clk lane tx_lp_en contrl selection.
56  *		1: from register. 0: from clk lane state machine.
57  * [28] register bit for clock lane tx_lp_en.
58  * [27] chan0 tx_hs_en control selection.
59  *		1: from register. 0: from chan0 state machine.
60  * [26] register bit for chan0 tx_hs_en.
61  * [25] chan0 tx_lp_en control selection.
62  *		1: from register. 0: from chan0 state machine.
63  * [24] register bit from chan0 tx_lp_en.
64  * [23] chan0 rx_lp_en control selection.
65  *		1: from register. 0: from chan0 state machine.
66  * [22] register bit from chan0 rx_lp_en.
67  * [21] chan0 contention detection enable control selection.
68  *		1: from register. 0: from chan0 state machine.
69  * [20] register bit from chan0 contention dectection enable.
70  * [19] chan1 tx_hs_en control selection.
71  *		1: from register. 0: from chan0 state machine.
72  * [18] register bit for chan1 tx_hs_en.
73  * [17] chan1 tx_lp_en control selection.
74  *		1: from register. 0: from chan0 state machine.
75  * [16] register bit from chan1 tx_lp_en.
76  * [15] chan2 tx_hs_en control selection.
77  *		1: from register. 0: from chan0 state machine.
78  * [14] register bit for chan2 tx_hs_en.
79  * [13] chan2 tx_lp_en control selection.
80  *		1: from register. 0: from chan0 state machine.
81  * [12] register bit from chan2 tx_lp_en.
82  * [11] chan3 tx_hs_en control selection.
83  *		1: from register. 0: from chan0 state machine.
84  * [10] register bit for chan3 tx_hs_en.
85  * [9]  chan3 tx_lp_en control selection.
86  *		1: from register. 0: from chan0 state machine.
87  * [8]  register bit from chan3 tx_lp_en.
88  * [4]  clk chan power down. this bit is also used as the power down
89  *	of the whole MIPI_DSI_PHY.
90  * [3]  chan3 power down.
91  * [2]  chan2 power down.
92  * [1]  chan1 power down.
93  * [0]  chan0 power down.
94  */
95 #define MIPI_DSI_CHAN_CTRL				0x4
96 
97 /* [24]   rx turn watch dog triggered.
98  * [23]   rx esc watchdog  triggered.
99  * [22]   mbias ready.
100  * [21]   txclkesc  synced and ready.
101  * [20:17] clk lane state. {mbias_ready, tx_stop, tx_ulps, tx_hs_active}
102  * [16:13] chan3 state{0, tx_stop, tx_ulps, tx_hs_active}
103  * [12:9]  chan2 state.{0, tx_stop, tx_ulps, tx_hs_active}
104  * [8:5]   chan1 state. {0, tx_stop, tx_ulps, tx_hs_active}
105  * [4:0]   chan0 state. {TX_STOP, tx_ULPS, hs_active, direction, rxulpsesc}
106  */
107 #define MIPI_DSI_CHAN_STS				0x8
108 
109 /* [31:24] TCLK_PREPARE.
110  * [23:16] TCLK_ZERO.
111  * [15:8]  TCLK_POST.
112  * [7:0]   TCLK_TRAIL.
113  */
114 #define MIPI_DSI_CLK_TIM				0xc
115 
116 /* [31:24] THS_PREPARE.
117  * [23:16] THS_ZERO.
118  * [15:8]  THS_TRAIL.
119  * [7:0]   THS_EXIT.
120  */
121 #define MIPI_DSI_HS_TIM					0x10
122 
123 /* [31:24] tTA_GET.
124  * [23:16] tTA_GO.
125  * [15:8]  tTA_SURE.
126  * [7:0]   tLPX.
127  */
128 #define MIPI_DSI_LP_TIM					0x14
129 
130 /* wait time to  MIPI DIS analog ready. */
131 #define MIPI_DSI_ANA_UP_TIM				0x18
132 
133 /* TINIT. */
134 #define MIPI_DSI_INIT_TIM				0x1c
135 
136 /* TWAKEUP. */
137 #define MIPI_DSI_WAKEUP_TIM				0x20
138 
139 /* when in RxULPS check state, after the the logic enable the analog,
140  *	how long we should wait to check the lP state .
141  */
142 #define MIPI_DSI_LPOK_TIM				0x24
143 
144 /* Watchdog for RX low power state no finished. */
145 #define MIPI_DSI_LP_WCHDOG				0x28
146 
147 /* tMBIAS,  after send power up signals to analog,
148  *	how long we should wait for analog powered up.
149  */
150 #define MIPI_DSI_ANA_CTRL				0x2c
151 
152 /* [31:8]  reserved for future.
153  * [7:0]   tCLK_PRE.
154  */
155 #define MIPI_DSI_CLK_TIM1				0x30
156 
157 /* watchdog for turn around waiting time. */
158 #define MIPI_DSI_TURN_WCHDOG				0x34
159 
160 /* When in RxULPS state, how frequency we should to check
161  *	if the TX side out of ULPS state.
162  */
163 #define MIPI_DSI_ULPS_CHECK				0x38
164 #define MIPI_DSI_TEST_CTRL0				0x3c
165 #define MIPI_DSI_TEST_CTRL1				0x40
166 
167 struct phy_meson_axg_mipi_dphy_priv {
168 	struct device				*dev;
169 	struct regmap				*regmap;
170 	struct clk				*clk;
171 	struct reset_control			*reset;
172 	struct phy				*analog;
173 	struct phy_configure_opts_mipi_dphy	config;
174 };
175 
176 static const struct regmap_config phy_meson_axg_mipi_dphy_regmap_conf = {
177 	.reg_bits = 8,
178 	.val_bits = 32,
179 	.reg_stride = 4,
180 	.max_register = MIPI_DSI_TEST_CTRL1,
181 };
182 
phy_meson_axg_mipi_dphy_init(struct phy * phy)183 static int phy_meson_axg_mipi_dphy_init(struct phy *phy)
184 {
185 	struct phy_meson_axg_mipi_dphy_priv *priv = phy_get_drvdata(phy);
186 	int ret;
187 
188 	ret = phy_init(priv->analog);
189 	if (ret)
190 		return ret;
191 
192 	ret = reset_control_reset(priv->reset);
193 	if (ret)
194 		return ret;
195 
196 	return 0;
197 }
198 
phy_meson_axg_mipi_dphy_configure(struct phy * phy,union phy_configure_opts * opts)199 static int phy_meson_axg_mipi_dphy_configure(struct phy *phy,
200 					      union phy_configure_opts *opts)
201 {
202 	struct phy_meson_axg_mipi_dphy_priv *priv = phy_get_drvdata(phy);
203 	int ret;
204 
205 	ret = phy_mipi_dphy_config_validate(&opts->mipi_dphy);
206 	if (ret)
207 		return ret;
208 
209 	ret = phy_configure(priv->analog, opts);
210 	if (ret)
211 		return ret;
212 
213 	memcpy(&priv->config, opts, sizeof(priv->config));
214 
215 	return 0;
216 }
217 
phy_meson_axg_mipi_dphy_power_on(struct phy * phy)218 static int phy_meson_axg_mipi_dphy_power_on(struct phy *phy)
219 {
220 	struct phy_meson_axg_mipi_dphy_priv *priv = phy_get_drvdata(phy);
221 	int ret;
222 	unsigned long temp;
223 
224 	ret = phy_power_on(priv->analog);
225 	if (ret)
226 		return ret;
227 
228 	/* enable phy clock */
229 	regmap_write(priv->regmap, MIPI_DSI_PHY_CTRL,  0x1);
230 	regmap_write(priv->regmap, MIPI_DSI_PHY_CTRL,
231 		     BIT(0) | /* enable the DSI PLL clock . */
232 		     BIT(7) | /* enable pll clock which connected to DDR clock path */
233 		     BIT(8)); /* enable the clock divider counter */
234 
235 	/* enable the divider clock out */
236 	regmap_update_bits(priv->regmap, MIPI_DSI_PHY_CTRL, BIT(9), BIT(9));
237 
238 	/* enable the byte clock generation. */
239 	regmap_update_bits(priv->regmap, MIPI_DSI_PHY_CTRL, BIT(12), BIT(12));
240 	regmap_update_bits(priv->regmap, MIPI_DSI_PHY_CTRL, BIT(31), BIT(31));
241 	regmap_update_bits(priv->regmap, MIPI_DSI_PHY_CTRL, BIT(31), 0);
242 
243 	/* Calculate lanebyteclk period in ps */
244 	temp = (1000000 * 100) / (priv->config.hs_clk_rate / 1000);
245 	temp = temp * 8 * 10;
246 
247 	regmap_write(priv->regmap, MIPI_DSI_CLK_TIM,
248 		     DIV_ROUND_UP(priv->config.clk_trail, temp) |
249 		     (DIV_ROUND_UP(priv->config.clk_post +
250 				   priv->config.hs_trail, temp) << 8) |
251 		     (DIV_ROUND_UP(priv->config.clk_zero, temp) << 16) |
252 		     (DIV_ROUND_UP(priv->config.clk_prepare, temp) << 24));
253 	regmap_write(priv->regmap, MIPI_DSI_CLK_TIM1,
254 		     DIV_ROUND_UP(priv->config.clk_pre, BITS_PER_BYTE));
255 
256 	regmap_write(priv->regmap, MIPI_DSI_HS_TIM,
257 		     DIV_ROUND_UP(priv->config.hs_exit, temp) |
258 		     (DIV_ROUND_UP(priv->config.hs_trail, temp) << 8) |
259 		     (DIV_ROUND_UP(priv->config.hs_zero, temp) << 16) |
260 		     (DIV_ROUND_UP(priv->config.hs_prepare, temp) << 24));
261 
262 	regmap_write(priv->regmap, MIPI_DSI_LP_TIM,
263 		     DIV_ROUND_UP(priv->config.lpx, temp) |
264 		     (DIV_ROUND_UP(priv->config.ta_sure, temp) << 8) |
265 		     (DIV_ROUND_UP(priv->config.ta_go, temp) << 16) |
266 		     (DIV_ROUND_UP(priv->config.ta_get, temp) << 24));
267 
268 	regmap_write(priv->regmap, MIPI_DSI_ANA_UP_TIM, 0x0100);
269 	regmap_write(priv->regmap, MIPI_DSI_INIT_TIM,
270 		     DIV_ROUND_UP(priv->config.init * NSEC_PER_MSEC, temp));
271 	regmap_write(priv->regmap, MIPI_DSI_WAKEUP_TIM,
272 		     DIV_ROUND_UP(priv->config.wakeup * NSEC_PER_MSEC, temp));
273 	regmap_write(priv->regmap, MIPI_DSI_LPOK_TIM, 0x7C);
274 	regmap_write(priv->regmap, MIPI_DSI_ULPS_CHECK, 0x927C);
275 	regmap_write(priv->regmap, MIPI_DSI_LP_WCHDOG, 0x1000);
276 	regmap_write(priv->regmap, MIPI_DSI_TURN_WCHDOG, 0x1000);
277 
278 	/* Powerup the analog circuit */
279 	switch (priv->config.lanes) {
280 	case 1:
281 		regmap_write(priv->regmap, MIPI_DSI_CHAN_CTRL, 0xe);
282 		break;
283 	case 2:
284 		regmap_write(priv->regmap, MIPI_DSI_CHAN_CTRL, 0xc);
285 		break;
286 	case 3:
287 		regmap_write(priv->regmap, MIPI_DSI_CHAN_CTRL, 0x8);
288 		break;
289 	case 4:
290 	default:
291 		regmap_write(priv->regmap, MIPI_DSI_CHAN_CTRL, 0);
292 		break;
293 	}
294 
295 	/* Trigger a sync active for esc_clk */
296 	regmap_update_bits(priv->regmap, MIPI_DSI_PHY_CTRL, BIT(1), BIT(1));
297 
298 	return 0;
299 }
300 
phy_meson_axg_mipi_dphy_power_off(struct phy * phy)301 static int phy_meson_axg_mipi_dphy_power_off(struct phy *phy)
302 {
303 	struct phy_meson_axg_mipi_dphy_priv *priv = phy_get_drvdata(phy);
304 
305 	regmap_write(priv->regmap, MIPI_DSI_CHAN_CTRL, 0xf);
306 	regmap_write(priv->regmap, MIPI_DSI_PHY_CTRL, BIT(31));
307 
308 	phy_power_off(priv->analog);
309 
310 	return 0;
311 }
312 
phy_meson_axg_mipi_dphy_exit(struct phy * phy)313 static int phy_meson_axg_mipi_dphy_exit(struct phy *phy)
314 {
315 	struct phy_meson_axg_mipi_dphy_priv *priv = phy_get_drvdata(phy);
316 	int ret;
317 
318 	ret = phy_exit(priv->analog);
319 	if (ret)
320 		return ret;
321 
322 	return reset_control_reset(priv->reset);
323 }
324 
325 static const struct phy_ops phy_meson_axg_mipi_dphy_ops = {
326 	.configure	= phy_meson_axg_mipi_dphy_configure,
327 	.init		= phy_meson_axg_mipi_dphy_init,
328 	.exit		= phy_meson_axg_mipi_dphy_exit,
329 	.power_on	= phy_meson_axg_mipi_dphy_power_on,
330 	.power_off	= phy_meson_axg_mipi_dphy_power_off,
331 	.owner		= THIS_MODULE,
332 };
333 
phy_meson_axg_mipi_dphy_probe(struct platform_device * pdev)334 static int phy_meson_axg_mipi_dphy_probe(struct platform_device *pdev)
335 {
336 	struct device *dev = &pdev->dev;
337 	struct phy_provider *phy_provider;
338 	struct resource *res;
339 	struct phy_meson_axg_mipi_dphy_priv *priv;
340 	struct phy *phy;
341 	void __iomem *base;
342 	int ret;
343 
344 	priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
345 	if (!priv)
346 		return -ENOMEM;
347 
348 	priv->dev = dev;
349 	platform_set_drvdata(pdev, priv);
350 
351 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
352 	base = devm_ioremap_resource(dev, res);
353 	if (IS_ERR(base))
354 		return PTR_ERR(base);
355 
356 	priv->regmap = devm_regmap_init_mmio(dev, base,
357 					&phy_meson_axg_mipi_dphy_regmap_conf);
358 	if (IS_ERR(priv->regmap))
359 		return PTR_ERR(priv->regmap);
360 
361 	priv->clk = devm_clk_get(dev, "pclk");
362 	if (IS_ERR(priv->clk))
363 		return PTR_ERR(priv->clk);
364 
365 	priv->reset = devm_reset_control_get(dev, "phy");
366 	if (IS_ERR(priv->reset))
367 		return PTR_ERR(priv->reset);
368 
369 	priv->analog = devm_phy_get(dev, "analog");
370 	if (IS_ERR(priv->analog))
371 		return PTR_ERR(priv->analog);
372 
373 	ret = clk_prepare_enable(priv->clk);
374 	if (ret)
375 		return ret;
376 
377 	ret = reset_control_deassert(priv->reset);
378 	if (ret)
379 		return ret;
380 
381 	phy = devm_phy_create(dev, NULL, &phy_meson_axg_mipi_dphy_ops);
382 	if (IS_ERR(phy)) {
383 		ret = PTR_ERR(phy);
384 		if (ret != -EPROBE_DEFER)
385 			dev_err(dev, "failed to create PHY\n");
386 
387 		return ret;
388 	}
389 
390 	phy_set_drvdata(phy, priv);
391 
392 	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
393 
394 	return PTR_ERR_OR_ZERO(phy_provider);
395 }
396 
397 static const struct of_device_id phy_meson_axg_mipi_dphy_of_match[] = {
398 	{ .compatible = "amlogic,axg-mipi-dphy", },
399 	{ },
400 };
401 MODULE_DEVICE_TABLE(of, phy_meson_axg_mipi_dphy_of_match);
402 
403 static struct platform_driver phy_meson_axg_mipi_dphy_driver = {
404 	.probe	= phy_meson_axg_mipi_dphy_probe,
405 	.driver	= {
406 		.name		= "phy-meson-axg-mipi-dphy",
407 		.of_match_table	= phy_meson_axg_mipi_dphy_of_match,
408 	},
409 };
410 module_platform_driver(phy_meson_axg_mipi_dphy_driver);
411 
412 MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>");
413 MODULE_DESCRIPTION("Meson AXG MIPI DPHY driver");
414 MODULE_LICENSE("GPL v2");
415