Searched refs:LOW (Results 1 – 25 of 68) sorted by relevance
123
| /linux-5.19.10/Documentation/devicetree/bindings/media/i2c/ |
| D | st,st-mipid02.txt | 45 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
46 LOW being the default.
47 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
48 LOW being the default.
|
| D | ov7670.txt | 13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| /linux-5.19.10/drivers/video/fbdev/omap/ |
| D | lcd_h3.c | 37 r = tps65010_set_gpio_out_value(GPIO1, LOW); in h3_panel_disable()
39 tps65010_set_gpio_out_value(GPIO2, LOW); in h3_panel_disable()
|
| /linux-5.19.10/Documentation/devicetree/bindings/regulator/ |
| D | gpio-regulator.yaml | 46 0: LOW
48 Default is LOW if nothing else is specified.
71 active LOW.
|
| D | maxim,max8973.yaml | 40 1 for HIGH and 0 for LOW.
|
| /linux-5.19.10/tools/power/cpupower/bench/ |
| D | example.cfg | 4 priority = LOW
|
| /linux-5.19.10/Documentation/devicetree/bindings/sound/ |
| D | cs35l34.txt | 35 0x0 (Default) = Selected by AD0 input (if AD0 = LOW, use left channel),
37 0x1 = Selected by the inversion of the AD0 input (if AD0 = LOW, use right
|
| /linux-5.19.10/arch/arm64/boot/dts/renesas/ |
| D | hihope-rzg2-ex-lvds.dtsi | 20 * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
|
| /linux-5.19.10/include/linux/mfd/ |
| D | tps65010.h | 121 #define LOW 0 macro
|
| /linux-5.19.10/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 54 When FPS event cleared (set to LOW), regulators, GPIOs and 32KHz
99 event cleared (set to LOW) whether it
125 control) then, GPIO1/nRST_IO goes LOW.
|
| D | rohm,bd9576-pmic.yaml | 36 the PMIC startup. If vout1-en is LOW during PMIC startup then the VOUT1
|
| /linux-5.19.10/arch/arm/boot/dts/ |
| D | rk3228-evb.dts | 67 rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
|
| D | meson8b-ec100.dts | 67 * GPIOAO_7 (power LED, which has to go LOW as well).
79 * Needs to go LOW (together with the poweroff GPIO)
82 * the output to LOW signals the EC to start a
|
| D | ste-href-ab8500.dtsi | 226 * Pins 26 and 35 muxed in as GPIO, and configured as OUTPUT LOW
|
| D | rk3288-rock2-som.dtsi | 251 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /linux-5.19.10/drivers/s390/crypto/ |
| D | zcrypt_msgtype6.h | 106 #define LOW 10 macro
|
| /linux-5.19.10/Documentation/devicetree/bindings/media/ |
| D | video-interfaces.yaml | 118 Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
124 Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively. Note,
156 Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively.
|
| /linux-5.19.10/Documentation/userspace-api/media/cec/ |
| D | cec-ioc-dqevent.rst | 153 * .. _`CEC-EVENT-PIN-CEC-LOW`:
167 * .. _`CEC-EVENT-PIN-HPD-LOW`:
185 * .. _`CEC-EVENT-PIN-5V-LOW`:
|
| /linux-5.19.10/Documentation/devicetree/bindings/thermal/ |
| D | rockchip-thermal.yaml | 67 description: The hardware-controlled active polarity 0:LOW 1:HIGH.
|
| /linux-5.19.10/arch/arm64/boot/dts/rockchip/ |
| D | rk3368-evb.dtsi | 225 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /linux-5.19.10/Documentation/devicetree/bindings/net/ |
| D | mediatek-bluetooth.txt | 66 - boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when
|
| /linux-5.19.10/Documentation/devicetree/bindings/memory-controllers/ddr/ |
| D | jedec,lpddr3-timings.yaml | 36 CKE minimum pulse width (HIGH and LOW pulse width) in pico seconds.
|
| /linux-5.19.10/Documentation/devicetree/bindings/clock/ |
| D | silabs,si5351.txt | 54 0 = clock output is driven LOW when disabled
|
| /linux-5.19.10/Documentation/driver-api/iio/ |
| D | buffers.rst | 57 |D3 |D2 |D1 |D0 | X | X | X | X | (LOW byte, address 0x06)
|
| /linux-5.19.10/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 73 FPS input event set to LOW.
|
123