| /linux-5.19.10/Documentation/devicetree/bindings/sound/ |
| D | tlv320adcx140.yaml | 123 output pins (GPO). These values are pairs, the first value is for the
127 GPO output configuration can be one of the following:
130 1 - GPOX is configured as a general-purpose output (GPO)
135 GPO output drive configuration for the GPO pins can be one of the following:
153 1 - GPIO1 is configured as a general-purpose output (GPO)
|
| /linux-5.19.10/Documentation/devicetree/bindings/mfd/ |
| D | twl6040.txt | 4 vibra and GPO functionality on OMAP4+ platforms.
13 - #gpio-cells = <1>: twl6040 provides GPO lines.
|
| D | rohm,bd71815-pmic.yaml | 76 The BD71815 has undocumented GPO at pin E5. Pin is marked as GND at the
79 second GPO by defining this property. Dont enable this if you are unsure
|
| /linux-5.19.10/Documentation/devicetree/bindings/iio/addac/ |
| D | adi,ad74413r.yaml | 98 Whether to configure GPO as a comparator or not.
99 When not configured as a comparator, the GPO will be treated as an
|
| /linux-5.19.10/Documentation/devicetree/bindings/gpio/ |
| D | gpio-pca9570.yaml | 7 title: PCA9570 I2C GPO expander
|
| D | gpio_lpc32xx.txt | 14 5: GPO P3
|
| /linux-5.19.10/Documentation/devicetree/bindings/hwmon/pmbus/ |
| D | ti,ucd90320.yaml | 18 margining (MARx), 16 for logical GPO, and 32 GPIs for cascading, and system
|
| /linux-5.19.10/Documentation/devicetree/bindings/mux/ |
| D | adi,adgs1408.txt | 12 - First cell is the GPO line number, i.e. 0 to 3
|
| D | adi,adg792a.txt | 13 - First cell is the GPO line number, i.e. 0 or 1
|
| /linux-5.19.10/drivers/pinctrl/nuvoton/ |
| D | pinctrl-npcm7xx.c | 914 #define GPO 0x2 /* Not GPI */ macro
968 …7XX_PINCFG(42, bmcuart0a, MFSEL1, 9, none, NONE, 0, none, NONE, 0, DSTR(2, 4) | GPO),
974 NPCM7XX_PINCFG(48, uart2, MFSEL1, 11, bmcuart0b, MFSEL4, 1, none, NONE, 0, GPO),
977 NPCM7XX_PINCFG(51, uart2, MFSEL1, 11, none, NONE, 0, none, NONE, 0, GPO),
979 NPCM7XX_PINCFG(53, uart2, MFSEL1, 11, none, NONE, 0, none, NONE, 0, GPO),
987 NPCM7XX_PINCFG(61, uart1, MFSEL1, 10, none, NONE, 0, none, NONE, 0, GPO),
988 NPCM7XX_PINCFG(62, uart1, MFSEL1, 10, bmcuart1, MFSEL3, 24, none, NONE, 0, GPO),
989 NPCM7XX_PINCFG(63, uart1, MFSEL1, 10, bmcuart1, MFSEL3, 24, none, NONE, 0, GPO),
1114 …X_PINCFG(184, spi3, MFSEL4, 16, none, NONE, 0, none, NONE, 0, DSTR(8, 12) | SLEW | GPO),
1115 …X_PINCFG(185, spi3, MFSEL4, 16, none, NONE, 0, none, NONE, 0, DSTR(8, 12) | SLEW | GPO),
[all …]
|
| /linux-5.19.10/drivers/gpio/ |
| D | Kconfig | 1072 tristate "PCA9570 4-Bit I2C GPO expander"
1074 Say yes here to enable the GPO driver for the NXP PCA9570 chip.
1105 tristate "TPIC2810 8-Bit I2C GPO expander"
1107 Say yes here to enable the GPO driver for the TI TPIC2810 chip.
1149 Support for GPO(s) on ROHM BD71815 PMIC. There are two GPOs
1266 tristate "TI LP873X GPO"
1269 This driver supports the GPO on TI Lp873x PMICs. 2 GPOs are present
1373 tristate "TI TPS65086 GPO"
1376 This driver supports the GPO on TI TPS65086x PMICs.
1432 tristate "TWL6040 GPO"
[all …]
|
| /linux-5.19.10/drivers/net/wan/ |
| D | hd64572.h | 96 #define GPO 0x131 /* General Purpose Output Pin Ctl Reg */ macro
|
| /linux-5.19.10/drivers/staging/rtl8192e/rtl8192e/ |
| D | r8192E_hw.h | 432 #define GPO 0x109 macro
|
| /linux-5.19.10/arch/arm/boot/dts/ |
| D | nuvoton-npcm730-gsj.dts | 437 /* GPO pins*/
|
| D | dove-cm-a510.dtsi | 100 /* Set upper NAND data bit to GPO */
|
| D | vf610-bk4.dts | 343 /* GPO */
|
| /linux-5.19.10/Documentation/hwmon/ |
| D | ucd9000.rst | 54 (MARx), 16 for logical GPO, and 32 GPIs for cascading, and system function.
|
| /linux-5.19.10/drivers/hid/ |
| D | Kconfig | 908 bool "GPO via leds class" if EXPERT
913 Provide access to PicoLCD's GPO pins via leds class.
|
| /linux-5.19.10/drivers/mfd/ |
| D | Kconfig | 1543 General Purpose Outputs (GPO) that are used in portable devices.
1557 General Purpose Outputs (GPO) that are used in portable devices.
|