| /linux-5.19.10/drivers/media/usb/dvb-usb/ |
| D | dib07x0.h | 9 GPIO3 = 4, enumerator
|
| /linux-5.19.10/arch/sh/kernel/cpu/sh4a/ |
| D | setup-shx3.c | 185 GPIO0, GPIO1, GPIO2, GPIO3, enumerator
233 INTC_VECT(GPIO2, 0xe80), INTC_VECT(GPIO3, 0xea0),
267 DU, GPIO3, GPIO2, GPIO1, GPIO0, PAM, 0, 0,
302 { 0xfe410810, 0, 32, 4, /* INT2PRI4 */ { 0, 0, PAM, GPIO3,
|
| /linux-5.19.10/Documentation/devicetree/bindings/sound/ |
| D | rt5640.txt | 28 2: using GPIO3 pin as dmic1 data pin
42 5: Use GPIO3 for jack-detect
|
| D | rt5668.txt | 22 1: using GPIO3 pin as dmic1 clock pin
|
| D | rt5677.txt | 39 Select 0 ~ 3 as OFF, GPIO1, GPIO2 and GPIO3 respectively.
|
| D | rt5682.txt | 22 1: using GPIO3 pin as dmic1 clock pin
|
| D | realtek,rt5682s.yaml | 41 - 2 # using GPIO3 pin as dmic1 clock pin
|
| /linux-5.19.10/drivers/pinctrl/ |
| D | pinctrl-xway.c | 119 MFP_XWAY(GPIO3, GPIO, CGU, NONE, PCI),
226 static const unsigned pins_clkout2[] = {GPIO3};
235 static const unsigned pins_pci_req3[] = {GPIO3};
355 MFP_XWAY(GPIO3, GPIO, STP, EPHY, EBU),
394 static const unsigned ase_pins_stp[] = {GPIO1, GPIO2, GPIO3};
397 static const unsigned ase_pins_ephy_led1[] = {GPIO3};
483 MFP_XWAY(GPIO3, GPIO, CGU, SDIO, PCI),
557 static const unsigned danube_pins_clkout2[] = {GPIO3};
565 static const unsigned danube_pins_pci_req3[] = {GPIO3};
658 MFP_XWAY(GPIO3, GPIO, CGU, SDIO, PCI),
[all …]
|
| D | pinctrl-lantiq.h | 109 GPIO3, enumerator
|
| /linux-5.19.10/arch/arm64/boot/dts/rockchip/ |
| D | rk3566-soquartz-cm4.dts | 57 * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
94 * pin 56 - GPIO3 - i2s1_sdo3_m1, shared with i2c2
|
| D | rk3399-gru-chromebook.dtsi | 356 gpio-line-names = /* GPIO3 A 0-7 */
366 /* GPIO3 B 0-7 */
376 /* GPIO3 C 0-7 */
386 /* GPIO3 D 0-7 */
|
| D | rk3399-gru-scarlet.dtsi | 507 gpio-line-names = /* GPIO3 A 0-7 */
517 /* GPIO3 B 0-7 */
527 /* GPIO3 C 0-7 */
537 /* GPIO3 D 0-7 */
|
| /linux-5.19.10/arch/arm/mach-pxa/ |
| D | pxa300.c | 27 MFP_ADDR_X(GPIO3, GPIO26, 0x027c),
|
| D | pxa930.c | 27 MFP_ADDR(GPIO3, 0x02d8),
|
| /linux-5.19.10/include/linux/mfd/ |
| D | tps65010.h | 119 #define GPIO3 3 macro
|
| /linux-5.19.10/Documentation/devicetree/bindings/interrupt-controller/ |
| D | rda,8810pl-intc.txt | 32 14: GPIO3
|
| D | brcm,bcm2835-armctrl-ic.txt | 99 20: GPIO3
|
| /linux-5.19.10/Documentation/devicetree/bindings/pinctrl/ |
| D | ste,nomadik.txt | 119 pins = "GPIO1", "GPIO3";
133 pins = "GPIO3";
|
| D | ste,abx500.txt | 51 pins = "GPIO3";
|
| /linux-5.19.10/arch/arm/boot/dts/ |
| D | bcm2835-rpi-cm1-io1.dts | 22 "GPIO3",
|
| D | bcm2837-rpi-cm3-io3.dts | 22 "GPIO3",
|
| /linux-5.19.10/Documentation/devicetree/bindings/gpio/ |
| D | xylon,logicvc-gpio.yaml | 68 gpio-line-names = "GPIO0", "GPIO1", "GPIO2", "GPIO3", "GPIO4",
|
| /linux-5.19.10/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 34 and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
46 Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power
|
| D | as3711.txt | 33 - su2-fbprot-gpio3 : GPIO3 is used for over-voltage protection
|
| /linux-5.19.10/arch/mips/boot/dts/ralink/ |
| D | gardena_smart_gateway_mt7688.dts | 46 * well for GPIO3. But this is already claimed for uart1
|