1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * comedi/drivers/mite.c
4 * Hardware driver for NI Mite PCI interface chip
5 *
6 * COMEDI - Linux Control and Measurement Device Interface
7 * Copyright (C) 1997-2002 David A. Schleef <ds@schleef.org>
8 */
9
10 /*
11 * The PCI-MIO E series driver was originally written by
12 * Tomasz Motylewski <...>, and ported to comedi by ds.
13 *
14 * References for specifications:
15 *
16 * 321747b.pdf Register Level Programmer Manual (obsolete)
17 * 321747c.pdf Register Level Programmer Manual (new)
18 * DAQ-STC reference manual
19 *
20 * Other possibly relevant info:
21 *
22 * 320517c.pdf User manual (obsolete)
23 * 320517f.pdf User manual (new)
24 * 320889a.pdf delete
25 * 320906c.pdf maximum signal ratings
26 * 321066a.pdf about 16x
27 * 321791a.pdf discontinuation of at-mio-16e-10 rev. c
28 * 321808a.pdf about at-mio-16e-10 rev P
29 * 321837a.pdf discontinuation of at-mio-16de-10 rev d
30 * 321838a.pdf about at-mio-16de-10 rev N
31 *
32 * ISSUES:
33 *
34 */
35
36 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
37
38 #include <linux/module.h>
39 #include <linux/slab.h>
40 #include <linux/log2.h>
41 #include <linux/comedi/comedi_pci.h>
42
43 #include "mite.h"
44
45 /*
46 * Mite registers
47 */
48 #define MITE_UNKNOWN_DMA_BURST_REG 0x28
49 #define UNKNOWN_DMA_BURST_ENABLE_BITS 0x600
50
51 #define MITE_PCI_CONFIG_OFFSET 0x300
52 #define MITE_CSIGR 0x460 /* chip signature */
53 #define CSIGR_TO_IOWINS(x) (((x) >> 29) & 0x7)
54 #define CSIGR_TO_WINS(x) (((x) >> 24) & 0x1f)
55 #define CSIGR_TO_WPDEP(x) (((x) >> 20) & 0x7)
56 #define CSIGR_TO_DMAC(x) (((x) >> 16) & 0xf)
57 #define CSIGR_TO_IMODE(x) (((x) >> 12) & 0x3) /* pci=0x3 */
58 #define CSIGR_TO_MMODE(x) (((x) >> 8) & 0x3) /* minimite=1 */
59 #define CSIGR_TO_TYPE(x) (((x) >> 4) & 0xf) /* mite=0, minimite=1 */
60 #define CSIGR_TO_VER(x) (((x) >> 0) & 0xf)
61
62 #define MITE_CHAN(x) (0x500 + 0x100 * (x))
63 #define MITE_CHOR(x) (0x00 + MITE_CHAN(x)) /* channel operation */
64 #define CHOR_DMARESET BIT(31)
65 #define CHOR_SET_SEND_TC BIT(11)
66 #define CHOR_CLR_SEND_TC BIT(10)
67 #define CHOR_SET_LPAUSE BIT(9)
68 #define CHOR_CLR_LPAUSE BIT(8)
69 #define CHOR_CLRDONE BIT(7)
70 #define CHOR_CLRRB BIT(6)
71 #define CHOR_CLRLC BIT(5)
72 #define CHOR_FRESET BIT(4)
73 #define CHOR_ABORT BIT(3) /* stop without emptying fifo */
74 #define CHOR_STOP BIT(2) /* stop after emptying fifo */
75 #define CHOR_CONT BIT(1)
76 #define CHOR_START BIT(0)
77 #define MITE_CHCR(x) (0x04 + MITE_CHAN(x)) /* channel control */
78 #define CHCR_SET_DMA_IE BIT(31)
79 #define CHCR_CLR_DMA_IE BIT(30)
80 #define CHCR_SET_LINKP_IE BIT(29)
81 #define CHCR_CLR_LINKP_IE BIT(28)
82 #define CHCR_SET_SAR_IE BIT(27)
83 #define CHCR_CLR_SAR_IE BIT(26)
84 #define CHCR_SET_DONE_IE BIT(25)
85 #define CHCR_CLR_DONE_IE BIT(24)
86 #define CHCR_SET_MRDY_IE BIT(23)
87 #define CHCR_CLR_MRDY_IE BIT(22)
88 #define CHCR_SET_DRDY_IE BIT(21)
89 #define CHCR_CLR_DRDY_IE BIT(20)
90 #define CHCR_SET_LC_IE BIT(19)
91 #define CHCR_CLR_LC_IE BIT(18)
92 #define CHCR_SET_CONT_RB_IE BIT(17)
93 #define CHCR_CLR_CONT_RB_IE BIT(16)
94 #define CHCR_FIFO(x) (((x) & 0x1) << 15)
95 #define CHCR_FIFODIS CHCR_FIFO(1)
96 #define CHCR_FIFO_ON CHCR_FIFO(0)
97 #define CHCR_BURST(x) (((x) & 0x1) << 14)
98 #define CHCR_BURSTEN CHCR_BURST(1)
99 #define CHCR_NO_BURSTEN CHCR_BURST(0)
100 #define CHCR_BYTE_SWAP_DEVICE BIT(6)
101 #define CHCR_BYTE_SWAP_MEMORY BIT(4)
102 #define CHCR_DIR(x) (((x) & 0x1) << 3)
103 #define CHCR_DEV_TO_MEM CHCR_DIR(1)
104 #define CHCR_MEM_TO_DEV CHCR_DIR(0)
105 #define CHCR_MODE(x) (((x) & 0x7) << 0)
106 #define CHCR_NORMAL CHCR_MODE(0)
107 #define CHCR_CONTINUE CHCR_MODE(1)
108 #define CHCR_RINGBUFF CHCR_MODE(2)
109 #define CHCR_LINKSHORT CHCR_MODE(4)
110 #define CHCR_LINKLONG CHCR_MODE(5)
111 #define MITE_TCR(x) (0x08 + MITE_CHAN(x)) /* transfer count */
112 #define MITE_MCR(x) (0x0c + MITE_CHAN(x)) /* memory config */
113 #define MITE_MAR(x) (0x10 + MITE_CHAN(x)) /* memory address */
114 #define MITE_DCR(x) (0x14 + MITE_CHAN(x)) /* device config */
115 #define DCR_NORMAL BIT(29)
116 #define MITE_DAR(x) (0x18 + MITE_CHAN(x)) /* device address */
117 #define MITE_LKCR(x) (0x1c + MITE_CHAN(x)) /* link config */
118 #define MITE_LKAR(x) (0x20 + MITE_CHAN(x)) /* link address */
119 #define MITE_LLKAR(x) (0x24 + MITE_CHAN(x)) /* see tnt5002 manual */
120 #define MITE_BAR(x) (0x28 + MITE_CHAN(x)) /* base address */
121 #define MITE_BCR(x) (0x2c + MITE_CHAN(x)) /* base count */
122 #define MITE_SAR(x) (0x30 + MITE_CHAN(x)) /* ? address */
123 #define MITE_WSCR(x) (0x34 + MITE_CHAN(x)) /* ? */
124 #define MITE_WSER(x) (0x38 + MITE_CHAN(x)) /* ? */
125 #define MITE_CHSR(x) (0x3c + MITE_CHAN(x)) /* channel status */
126 #define CHSR_INT BIT(31)
127 #define CHSR_LPAUSES BIT(29)
128 #define CHSR_SARS BIT(27)
129 #define CHSR_DONE BIT(25)
130 #define CHSR_MRDY BIT(23)
131 #define CHSR_DRDY BIT(21)
132 #define CHSR_LINKC BIT(19)
133 #define CHSR_CONTS_RB BIT(17)
134 #define CHSR_ERROR BIT(15)
135 #define CHSR_SABORT BIT(14)
136 #define CHSR_HABORT BIT(13)
137 #define CHSR_STOPS BIT(12)
138 #define CHSR_OPERR(x) (((x) & 0x3) << 10)
139 #define CHSR_OPERR_MASK CHSR_OPERR(3)
140 #define CHSR_OPERR_NOERROR CHSR_OPERR(0)
141 #define CHSR_OPERR_FIFOERROR CHSR_OPERR(1)
142 #define CHSR_OPERR_LINKERROR CHSR_OPERR(1) /* ??? */
143 #define CHSR_XFERR BIT(9)
144 #define CHSR_END BIT(8)
145 #define CHSR_DRQ1 BIT(7)
146 #define CHSR_DRQ0 BIT(6)
147 #define CHSR_LERR(x) (((x) & 0x3) << 4)
148 #define CHSR_LERR_MASK CHSR_LERR(3)
149 #define CHSR_LBERR CHSR_LERR(1)
150 #define CHSR_LRERR CHSR_LERR(2)
151 #define CHSR_LOERR CHSR_LERR(3)
152 #define CHSR_MERR(x) (((x) & 0x3) << 2)
153 #define CHSR_MERR_MASK CHSR_MERR(3)
154 #define CHSR_MBERR CHSR_MERR(1)
155 #define CHSR_MRERR CHSR_MERR(2)
156 #define CHSR_MOERR CHSR_MERR(3)
157 #define CHSR_DERR(x) (((x) & 0x3) << 0)
158 #define CHSR_DERR_MASK CHSR_DERR(3)
159 #define CHSR_DBERR CHSR_DERR(1)
160 #define CHSR_DRERR CHSR_DERR(2)
161 #define CHSR_DOERR CHSR_DERR(3)
162 #define MITE_FCR(x) (0x40 + MITE_CHAN(x)) /* fifo count */
163
164 /* common bits for the memory/device/link config registers */
165 #define CR_RL(x) (((x) & 0x7) << 21)
166 #define CR_REQS(x) (((x) & 0x7) << 16)
167 #define CR_REQS_MASK CR_REQS(7)
168 #define CR_ASEQ(x) (((x) & 0x3) << 10)
169 #define CR_ASEQDONT CR_ASEQ(0)
170 #define CR_ASEQUP CR_ASEQ(1)
171 #define CR_ASEQDOWN CR_ASEQ(2)
172 #define CR_ASEQ_MASK CR_ASEQ(3)
173 #define CR_PSIZE(x) (((x) & 0x3) << 8)
174 #define CR_PSIZE8 CR_PSIZE(1)
175 #define CR_PSIZE16 CR_PSIZE(2)
176 #define CR_PSIZE32 CR_PSIZE(3)
177 #define CR_PORT(x) (((x) & 0x3) << 6)
178 #define CR_PORTCPU CR_PORT(0)
179 #define CR_PORTIO CR_PORT(1)
180 #define CR_PORTVXI CR_PORT(2)
181 #define CR_PORTMXI CR_PORT(3)
182 #define CR_AMDEVICE BIT(0)
183
MITE_IODWBSR_1_WSIZE_bits(unsigned int size)184 static unsigned int MITE_IODWBSR_1_WSIZE_bits(unsigned int size)
185 {
186 return (ilog2(size) - 1) & 0x1f;
187 }
188
mite_retry_limit(unsigned int retry_limit)189 static unsigned int mite_retry_limit(unsigned int retry_limit)
190 {
191 unsigned int value = 0;
192
193 if (retry_limit)
194 value = 1 + ilog2(retry_limit);
195 if (value > 0x7)
196 value = 0x7;
197 return CR_RL(value);
198 }
199
mite_drq_reqs(unsigned int drq_line)200 static unsigned int mite_drq_reqs(unsigned int drq_line)
201 {
202 /* This also works on m-series when using channels (drq_line) 4 or 5. */
203 return CR_REQS((drq_line & 0x3) | 0x4);
204 }
205
mite_fifo_size(struct mite * mite,unsigned int channel)206 static unsigned int mite_fifo_size(struct mite *mite, unsigned int channel)
207 {
208 unsigned int fcr_bits = readl(mite->mmio + MITE_FCR(channel));
209 unsigned int empty_count = (fcr_bits >> 16) & 0xff;
210 unsigned int full_count = fcr_bits & 0xff;
211
212 return empty_count + full_count;
213 }
214
mite_device_bytes_transferred(struct mite_channel * mite_chan)215 static u32 mite_device_bytes_transferred(struct mite_channel *mite_chan)
216 {
217 struct mite *mite = mite_chan->mite;
218
219 return readl(mite->mmio + MITE_DAR(mite_chan->channel));
220 }
221
222 /**
223 * mite_bytes_in_transit() - Returns the number of unread bytes in the fifo.
224 * @mite_chan: MITE dma channel.
225 */
mite_bytes_in_transit(struct mite_channel * mite_chan)226 u32 mite_bytes_in_transit(struct mite_channel *mite_chan)
227 {
228 struct mite *mite = mite_chan->mite;
229
230 return readl(mite->mmio + MITE_FCR(mite_chan->channel)) & 0xff;
231 }
232 EXPORT_SYMBOL_GPL(mite_bytes_in_transit);
233
234 /* returns lower bound for number of bytes transferred from device to memory */
mite_bytes_written_to_memory_lb(struct mite_channel * mite_chan)235 static u32 mite_bytes_written_to_memory_lb(struct mite_channel *mite_chan)
236 {
237 u32 device_byte_count;
238
239 device_byte_count = mite_device_bytes_transferred(mite_chan);
240 return device_byte_count - mite_bytes_in_transit(mite_chan);
241 }
242
243 /* returns upper bound for number of bytes transferred from device to memory */
mite_bytes_written_to_memory_ub(struct mite_channel * mite_chan)244 static u32 mite_bytes_written_to_memory_ub(struct mite_channel *mite_chan)
245 {
246 u32 in_transit_count;
247
248 in_transit_count = mite_bytes_in_transit(mite_chan);
249 return mite_device_bytes_transferred(mite_chan) - in_transit_count;
250 }
251
252 /* returns lower bound for number of bytes read from memory to device */
mite_bytes_read_from_memory_lb(struct mite_channel * mite_chan)253 static u32 mite_bytes_read_from_memory_lb(struct mite_channel *mite_chan)
254 {
255 u32 device_byte_count;
256
257 device_byte_count = mite_device_bytes_transferred(mite_chan);
258 return device_byte_count + mite_bytes_in_transit(mite_chan);
259 }
260
261 /* returns upper bound for number of bytes read from memory to device */
mite_bytes_read_from_memory_ub(struct mite_channel * mite_chan)262 static u32 mite_bytes_read_from_memory_ub(struct mite_channel *mite_chan)
263 {
264 u32 in_transit_count;
265
266 in_transit_count = mite_bytes_in_transit(mite_chan);
267 return mite_device_bytes_transferred(mite_chan) + in_transit_count;
268 }
269
mite_sync_input_dma(struct mite_channel * mite_chan,struct comedi_subdevice * s)270 static void mite_sync_input_dma(struct mite_channel *mite_chan,
271 struct comedi_subdevice *s)
272 {
273 struct comedi_async *async = s->async;
274 int count;
275 unsigned int nbytes, old_alloc_count;
276
277 old_alloc_count = async->buf_write_alloc_count;
278 /* write alloc as much as we can */
279 comedi_buf_write_alloc(s, async->prealloc_bufsz);
280
281 nbytes = mite_bytes_written_to_memory_lb(mite_chan);
282 if ((int)(mite_bytes_written_to_memory_ub(mite_chan) -
283 old_alloc_count) > 0) {
284 dev_warn(s->device->class_dev,
285 "mite: DMA overwrite of free area\n");
286 async->events |= COMEDI_CB_OVERFLOW;
287 return;
288 }
289
290 count = nbytes - async->buf_write_count;
291 /*
292 * it's possible count will be negative due to conservative value
293 * returned by mite_bytes_written_to_memory_lb
294 */
295 if (count > 0) {
296 comedi_buf_write_free(s, count);
297 comedi_inc_scan_progress(s, count);
298 async->events |= COMEDI_CB_BLOCK;
299 }
300 }
301
mite_sync_output_dma(struct mite_channel * mite_chan,struct comedi_subdevice * s)302 static void mite_sync_output_dma(struct mite_channel *mite_chan,
303 struct comedi_subdevice *s)
304 {
305 struct comedi_async *async = s->async;
306 struct comedi_cmd *cmd = &async->cmd;
307 u32 stop_count = cmd->stop_arg * comedi_bytes_per_scan(s);
308 unsigned int old_alloc_count = async->buf_read_alloc_count;
309 u32 nbytes_ub, nbytes_lb;
310 int count;
311 bool finite_regen = (cmd->stop_src == TRIG_NONE && stop_count != 0);
312
313 /* read alloc as much as we can */
314 comedi_buf_read_alloc(s, async->prealloc_bufsz);
315 nbytes_lb = mite_bytes_read_from_memory_lb(mite_chan);
316 if (cmd->stop_src == TRIG_COUNT && (int)(nbytes_lb - stop_count) > 0)
317 nbytes_lb = stop_count;
318 nbytes_ub = mite_bytes_read_from_memory_ub(mite_chan);
319 if (cmd->stop_src == TRIG_COUNT && (int)(nbytes_ub - stop_count) > 0)
320 nbytes_ub = stop_count;
321
322 if ((!finite_regen || stop_count > old_alloc_count) &&
323 ((int)(nbytes_ub - old_alloc_count) > 0)) {
324 dev_warn(s->device->class_dev, "mite: DMA underrun\n");
325 async->events |= COMEDI_CB_OVERFLOW;
326 return;
327 }
328
329 if (finite_regen) {
330 /*
331 * This is a special case where we continuously output a finite
332 * buffer. In this case, we do not free any of the memory,
333 * hence we expect that old_alloc_count will reach a maximum of
334 * stop_count bytes.
335 */
336 return;
337 }
338
339 count = nbytes_lb - async->buf_read_count;
340 if (count > 0) {
341 comedi_buf_read_free(s, count);
342 async->events |= COMEDI_CB_BLOCK;
343 }
344 }
345
346 /**
347 * mite_sync_dma() - Sync the MITE dma with the COMEDI async buffer.
348 * @mite_chan: MITE dma channel.
349 * @s: COMEDI subdevice.
350 */
mite_sync_dma(struct mite_channel * mite_chan,struct comedi_subdevice * s)351 void mite_sync_dma(struct mite_channel *mite_chan, struct comedi_subdevice *s)
352 {
353 if (mite_chan->dir == COMEDI_INPUT)
354 mite_sync_input_dma(mite_chan, s);
355 else
356 mite_sync_output_dma(mite_chan, s);
357 }
358 EXPORT_SYMBOL_GPL(mite_sync_dma);
359
mite_get_status(struct mite_channel * mite_chan)360 static unsigned int mite_get_status(struct mite_channel *mite_chan)
361 {
362 struct mite *mite = mite_chan->mite;
363 unsigned int status;
364 unsigned long flags;
365
366 spin_lock_irqsave(&mite->lock, flags);
367 status = readl(mite->mmio + MITE_CHSR(mite_chan->channel));
368 if (status & CHSR_DONE) {
369 mite_chan->done = 1;
370 writel(CHOR_CLRDONE,
371 mite->mmio + MITE_CHOR(mite_chan->channel));
372 }
373 spin_unlock_irqrestore(&mite->lock, flags);
374 return status;
375 }
376
377 /**
378 * mite_ack_linkc() - Check and ack the LINKC interrupt,
379 * @mite_chan: MITE dma channel.
380 * @s: COMEDI subdevice.
381 * @sync: flag to force a mite_sync_dma().
382 *
383 * This will also ack the DONE interrupt if active.
384 */
mite_ack_linkc(struct mite_channel * mite_chan,struct comedi_subdevice * s,bool sync)385 void mite_ack_linkc(struct mite_channel *mite_chan,
386 struct comedi_subdevice *s,
387 bool sync)
388 {
389 struct mite *mite = mite_chan->mite;
390 unsigned int status;
391
392 status = mite_get_status(mite_chan);
393 if (status & CHSR_LINKC) {
394 writel(CHOR_CLRLC, mite->mmio + MITE_CHOR(mite_chan->channel));
395 sync = true;
396 }
397 if (sync)
398 mite_sync_dma(mite_chan, s);
399
400 if (status & CHSR_XFERR) {
401 dev_err(s->device->class_dev,
402 "mite: transfer error %08x\n", status);
403 s->async->events |= COMEDI_CB_ERROR;
404 }
405 }
406 EXPORT_SYMBOL_GPL(mite_ack_linkc);
407
408 /**
409 * mite_done() - Check is a MITE dma transfer is complete.
410 * @mite_chan: MITE dma channel.
411 *
412 * This will also ack the DONE interrupt if active.
413 */
mite_done(struct mite_channel * mite_chan)414 int mite_done(struct mite_channel *mite_chan)
415 {
416 struct mite *mite = mite_chan->mite;
417 unsigned long flags;
418 int done;
419
420 mite_get_status(mite_chan);
421 spin_lock_irqsave(&mite->lock, flags);
422 done = mite_chan->done;
423 spin_unlock_irqrestore(&mite->lock, flags);
424 return done;
425 }
426 EXPORT_SYMBOL_GPL(mite_done);
427
mite_dma_reset(struct mite_channel * mite_chan)428 static void mite_dma_reset(struct mite_channel *mite_chan)
429 {
430 writel(CHOR_DMARESET | CHOR_FRESET,
431 mite_chan->mite->mmio + MITE_CHOR(mite_chan->channel));
432 }
433
434 /**
435 * mite_dma_arm() - Start a MITE dma transfer.
436 * @mite_chan: MITE dma channel.
437 */
mite_dma_arm(struct mite_channel * mite_chan)438 void mite_dma_arm(struct mite_channel *mite_chan)
439 {
440 struct mite *mite = mite_chan->mite;
441 unsigned long flags;
442
443 /*
444 * memory barrier is intended to insure any twiddling with the buffer
445 * is done before writing to the mite to arm dma transfer
446 */
447 smp_mb();
448 spin_lock_irqsave(&mite->lock, flags);
449 mite_chan->done = 0;
450 /* arm */
451 writel(CHOR_START, mite->mmio + MITE_CHOR(mite_chan->channel));
452 spin_unlock_irqrestore(&mite->lock, flags);
453 }
454 EXPORT_SYMBOL_GPL(mite_dma_arm);
455
456 /**
457 * mite_dma_disarm() - Stop a MITE dma transfer.
458 * @mite_chan: MITE dma channel.
459 */
mite_dma_disarm(struct mite_channel * mite_chan)460 void mite_dma_disarm(struct mite_channel *mite_chan)
461 {
462 struct mite *mite = mite_chan->mite;
463
464 /* disarm */
465 writel(CHOR_ABORT, mite->mmio + MITE_CHOR(mite_chan->channel));
466 }
467 EXPORT_SYMBOL_GPL(mite_dma_disarm);
468
469 /**
470 * mite_prep_dma() - Prepare a MITE dma channel for transfers.
471 * @mite_chan: MITE dma channel.
472 * @num_device_bits: device transfer size (8, 16, or 32-bits).
473 * @num_memory_bits: memory transfer size (8, 16, or 32-bits).
474 */
mite_prep_dma(struct mite_channel * mite_chan,unsigned int num_device_bits,unsigned int num_memory_bits)475 void mite_prep_dma(struct mite_channel *mite_chan,
476 unsigned int num_device_bits, unsigned int num_memory_bits)
477 {
478 struct mite *mite = mite_chan->mite;
479 unsigned int chcr, mcr, dcr, lkcr;
480
481 mite_dma_reset(mite_chan);
482
483 /* short link chaining mode */
484 chcr = CHCR_SET_DMA_IE | CHCR_LINKSHORT | CHCR_SET_DONE_IE |
485 CHCR_BURSTEN;
486 /*
487 * Link Complete Interrupt: interrupt every time a link
488 * in MITE_RING is completed. This can generate a lot of
489 * extra interrupts, but right now we update the values
490 * of buf_int_ptr and buf_int_count at each interrupt. A
491 * better method is to poll the MITE before each user
492 * "read()" to calculate the number of bytes available.
493 */
494 chcr |= CHCR_SET_LC_IE;
495 if (num_memory_bits == 32 && num_device_bits == 16) {
496 /*
497 * Doing a combined 32 and 16 bit byteswap gets the 16 bit
498 * samples into the fifo in the right order. Tested doing 32 bit
499 * memory to 16 bit device transfers to the analog out of a
500 * pxi-6281, which has mite version = 1, type = 4. This also
501 * works for dma reads from the counters on e-series boards.
502 */
503 chcr |= CHCR_BYTE_SWAP_DEVICE | CHCR_BYTE_SWAP_MEMORY;
504 }
505 if (mite_chan->dir == COMEDI_INPUT)
506 chcr |= CHCR_DEV_TO_MEM;
507
508 writel(chcr, mite->mmio + MITE_CHCR(mite_chan->channel));
509
510 /* to/from memory */
511 mcr = mite_retry_limit(64) | CR_ASEQUP;
512 switch (num_memory_bits) {
513 case 8:
514 mcr |= CR_PSIZE8;
515 break;
516 case 16:
517 mcr |= CR_PSIZE16;
518 break;
519 case 32:
520 mcr |= CR_PSIZE32;
521 break;
522 default:
523 pr_warn("bug! invalid mem bit width for dma transfer\n");
524 break;
525 }
526 writel(mcr, mite->mmio + MITE_MCR(mite_chan->channel));
527
528 /* from/to device */
529 dcr = mite_retry_limit(64) | CR_ASEQUP;
530 dcr |= CR_PORTIO | CR_AMDEVICE | mite_drq_reqs(mite_chan->channel);
531 switch (num_device_bits) {
532 case 8:
533 dcr |= CR_PSIZE8;
534 break;
535 case 16:
536 dcr |= CR_PSIZE16;
537 break;
538 case 32:
539 dcr |= CR_PSIZE32;
540 break;
541 default:
542 pr_warn("bug! invalid dev bit width for dma transfer\n");
543 break;
544 }
545 writel(dcr, mite->mmio + MITE_DCR(mite_chan->channel));
546
547 /* reset the DAR */
548 writel(0, mite->mmio + MITE_DAR(mite_chan->channel));
549
550 /* the link is 32bits */
551 lkcr = mite_retry_limit(64) | CR_ASEQUP | CR_PSIZE32;
552 writel(lkcr, mite->mmio + MITE_LKCR(mite_chan->channel));
553
554 /* starting address for link chaining */
555 writel(mite_chan->ring->dma_addr,
556 mite->mmio + MITE_LKAR(mite_chan->channel));
557 }
558 EXPORT_SYMBOL_GPL(mite_prep_dma);
559
560 /**
561 * mite_request_channel_in_range() - Request a MITE dma channel.
562 * @mite: MITE device.
563 * @ring: MITE dma ring.
564 * @min_channel: minimum channel index to use.
565 * @max_channel: maximum channel index to use.
566 */
mite_request_channel_in_range(struct mite * mite,struct mite_ring * ring,unsigned int min_channel,unsigned int max_channel)567 struct mite_channel *mite_request_channel_in_range(struct mite *mite,
568 struct mite_ring *ring,
569 unsigned int min_channel,
570 unsigned int max_channel)
571 {
572 struct mite_channel *mite_chan = NULL;
573 unsigned long flags;
574 int i;
575
576 /*
577 * spin lock so mite_release_channel can be called safely
578 * from interrupts
579 */
580 spin_lock_irqsave(&mite->lock, flags);
581 for (i = min_channel; i <= max_channel; ++i) {
582 mite_chan = &mite->channels[i];
583 if (!mite_chan->ring) {
584 mite_chan->ring = ring;
585 break;
586 }
587 mite_chan = NULL;
588 }
589 spin_unlock_irqrestore(&mite->lock, flags);
590 return mite_chan;
591 }
592 EXPORT_SYMBOL_GPL(mite_request_channel_in_range);
593
594 /**
595 * mite_request_channel() - Request a MITE dma channel.
596 * @mite: MITE device.
597 * @ring: MITE dma ring.
598 */
mite_request_channel(struct mite * mite,struct mite_ring * ring)599 struct mite_channel *mite_request_channel(struct mite *mite,
600 struct mite_ring *ring)
601 {
602 return mite_request_channel_in_range(mite, ring, 0,
603 mite->num_channels - 1);
604 }
605 EXPORT_SYMBOL_GPL(mite_request_channel);
606
607 /**
608 * mite_release_channel() - Release a MITE dma channel.
609 * @mite_chan: MITE dma channel.
610 */
mite_release_channel(struct mite_channel * mite_chan)611 void mite_release_channel(struct mite_channel *mite_chan)
612 {
613 struct mite *mite = mite_chan->mite;
614 unsigned long flags;
615
616 /* spin lock to prevent races with mite_request_channel */
617 spin_lock_irqsave(&mite->lock, flags);
618 if (mite_chan->ring) {
619 mite_dma_disarm(mite_chan);
620 mite_dma_reset(mite_chan);
621 /*
622 * disable all channel's interrupts (do it after disarm/reset so
623 * MITE_CHCR reg isn't changed while dma is still active!)
624 */
625 writel(CHCR_CLR_DMA_IE | CHCR_CLR_LINKP_IE |
626 CHCR_CLR_SAR_IE | CHCR_CLR_DONE_IE |
627 CHCR_CLR_MRDY_IE | CHCR_CLR_DRDY_IE |
628 CHCR_CLR_LC_IE | CHCR_CLR_CONT_RB_IE,
629 mite->mmio + MITE_CHCR(mite_chan->channel));
630 mite_chan->ring = NULL;
631 }
632 spin_unlock_irqrestore(&mite->lock, flags);
633 }
634 EXPORT_SYMBOL_GPL(mite_release_channel);
635
636 /**
637 * mite_init_ring_descriptors() - Initialize a MITE dma ring descriptors.
638 * @ring: MITE dma ring.
639 * @s: COMEDI subdevice.
640 * @nbytes: the size of the dma ring (in bytes).
641 *
642 * Initializes the ring buffer descriptors to provide correct DMA transfer
643 * links to the exact amount of memory required. When the ring buffer is
644 * allocated by mite_buf_change(), the default is to initialize the ring
645 * to refer to the entire DMA data buffer. A command may call this function
646 * later to re-initialize and shorten the amount of memory that will be
647 * transferred.
648 */
mite_init_ring_descriptors(struct mite_ring * ring,struct comedi_subdevice * s,unsigned int nbytes)649 int mite_init_ring_descriptors(struct mite_ring *ring,
650 struct comedi_subdevice *s,
651 unsigned int nbytes)
652 {
653 struct comedi_async *async = s->async;
654 struct mite_dma_desc *desc = NULL;
655 unsigned int n_full_links = nbytes >> PAGE_SHIFT;
656 unsigned int remainder = nbytes % PAGE_SIZE;
657 int i;
658
659 dev_dbg(s->device->class_dev,
660 "mite: init ring buffer to %u bytes\n", nbytes);
661
662 if ((n_full_links + (remainder > 0 ? 1 : 0)) > ring->n_links) {
663 dev_err(s->device->class_dev,
664 "mite: ring buffer too small for requested init\n");
665 return -ENOMEM;
666 }
667
668 /* We set the descriptors for all full links. */
669 for (i = 0; i < n_full_links; ++i) {
670 desc = &ring->descs[i];
671 desc->count = cpu_to_le32(PAGE_SIZE);
672 desc->addr = cpu_to_le32(async->buf_map->page_list[i].dma_addr);
673 desc->next = cpu_to_le32(ring->dma_addr +
674 (i + 1) * sizeof(*desc));
675 }
676
677 /* the last link is either a remainder or was a full link. */
678 if (remainder > 0) {
679 desc = &ring->descs[i];
680 /* set the lesser count for the remainder link */
681 desc->count = cpu_to_le32(remainder);
682 desc->addr = cpu_to_le32(async->buf_map->page_list[i].dma_addr);
683 }
684
685 /* Assign the last link->next to point back to the head of the list. */
686 desc->next = cpu_to_le32(ring->dma_addr);
687
688 /*
689 * barrier is meant to insure that all the writes to the dma descriptors
690 * have completed before the dma controller is commanded to read them
691 */
692 smp_wmb();
693 return 0;
694 }
695 EXPORT_SYMBOL_GPL(mite_init_ring_descriptors);
696
mite_free_dma_descs(struct mite_ring * ring)697 static void mite_free_dma_descs(struct mite_ring *ring)
698 {
699 struct mite_dma_desc *descs = ring->descs;
700
701 if (descs) {
702 dma_free_coherent(ring->hw_dev,
703 ring->n_links * sizeof(*descs),
704 descs, ring->dma_addr);
705 ring->descs = NULL;
706 ring->dma_addr = 0;
707 ring->n_links = 0;
708 }
709 }
710
711 /**
712 * mite_buf_change() - COMEDI subdevice (*buf_change) for a MITE dma ring.
713 * @ring: MITE dma ring.
714 * @s: COMEDI subdevice.
715 */
mite_buf_change(struct mite_ring * ring,struct comedi_subdevice * s)716 int mite_buf_change(struct mite_ring *ring, struct comedi_subdevice *s)
717 {
718 struct comedi_async *async = s->async;
719 struct mite_dma_desc *descs;
720 unsigned int n_links;
721
722 mite_free_dma_descs(ring);
723
724 if (async->prealloc_bufsz == 0)
725 return 0;
726
727 n_links = async->prealloc_bufsz >> PAGE_SHIFT;
728
729 descs = dma_alloc_coherent(ring->hw_dev,
730 n_links * sizeof(*descs),
731 &ring->dma_addr, GFP_KERNEL);
732 if (!descs) {
733 dev_err(s->device->class_dev,
734 "mite: ring buffer allocation failed\n");
735 return -ENOMEM;
736 }
737 ring->descs = descs;
738 ring->n_links = n_links;
739
740 return mite_init_ring_descriptors(ring, s, n_links << PAGE_SHIFT);
741 }
742 EXPORT_SYMBOL_GPL(mite_buf_change);
743
744 /**
745 * mite_alloc_ring() - Allocate a MITE dma ring.
746 * @mite: MITE device.
747 */
mite_alloc_ring(struct mite * mite)748 struct mite_ring *mite_alloc_ring(struct mite *mite)
749 {
750 struct mite_ring *ring;
751
752 ring = kmalloc(sizeof(*ring), GFP_KERNEL);
753 if (!ring)
754 return NULL;
755 ring->hw_dev = get_device(&mite->pcidev->dev);
756 if (!ring->hw_dev) {
757 kfree(ring);
758 return NULL;
759 }
760 ring->n_links = 0;
761 ring->descs = NULL;
762 ring->dma_addr = 0;
763 return ring;
764 }
765 EXPORT_SYMBOL_GPL(mite_alloc_ring);
766
767 /**
768 * mite_free_ring() - Free a MITE dma ring and its descriptors.
769 * @ring: MITE dma ring.
770 */
mite_free_ring(struct mite_ring * ring)771 void mite_free_ring(struct mite_ring *ring)
772 {
773 if (ring) {
774 mite_free_dma_descs(ring);
775 put_device(ring->hw_dev);
776 kfree(ring);
777 }
778 }
779 EXPORT_SYMBOL_GPL(mite_free_ring);
780
mite_setup(struct comedi_device * dev,struct mite * mite,bool use_win1)781 static int mite_setup(struct comedi_device *dev, struct mite *mite,
782 bool use_win1)
783 {
784 resource_size_t daq_phys_addr;
785 unsigned long length;
786 int i;
787 u32 csigr_bits;
788 unsigned int unknown_dma_burst_bits;
789 unsigned int wpdep;
790
791 pci_set_master(mite->pcidev);
792
793 mite->mmio = pci_ioremap_bar(mite->pcidev, 0);
794 if (!mite->mmio)
795 return -ENOMEM;
796
797 dev->mmio = pci_ioremap_bar(mite->pcidev, 1);
798 if (!dev->mmio)
799 return -ENOMEM;
800 daq_phys_addr = pci_resource_start(mite->pcidev, 1);
801 length = pci_resource_len(mite->pcidev, 1);
802
803 if (use_win1) {
804 writel(0, mite->mmio + MITE_IODWBSR);
805 dev_dbg(dev->class_dev,
806 "mite: using I/O Window Base Size register 1\n");
807 writel(daq_phys_addr | WENAB |
808 MITE_IODWBSR_1_WSIZE_bits(length),
809 mite->mmio + MITE_IODWBSR_1);
810 writel(0, mite->mmio + MITE_IODWCR_1);
811 } else {
812 writel(daq_phys_addr | WENAB, mite->mmio + MITE_IODWBSR);
813 }
814 /*
815 * Make sure dma bursts work. I got this from running a bus analyzer
816 * on a pxi-6281 and a pxi-6713. 6713 powered up with register value
817 * of 0x61f and bursts worked. 6281 powered up with register value of
818 * 0x1f and bursts didn't work. The NI windows driver reads the
819 * register, then does a bitwise-or of 0x600 with it and writes it back.
820 *
821 * The bits 0x90180700 in MITE_UNKNOWN_DMA_BURST_REG can be
822 * written and read back. The bits 0x1f always read as 1.
823 * The rest always read as zero.
824 */
825 unknown_dma_burst_bits = readl(mite->mmio + MITE_UNKNOWN_DMA_BURST_REG);
826 unknown_dma_burst_bits |= UNKNOWN_DMA_BURST_ENABLE_BITS;
827 writel(unknown_dma_burst_bits, mite->mmio + MITE_UNKNOWN_DMA_BURST_REG);
828
829 csigr_bits = readl(mite->mmio + MITE_CSIGR);
830 mite->num_channels = CSIGR_TO_DMAC(csigr_bits);
831 if (mite->num_channels > MAX_MITE_DMA_CHANNELS) {
832 dev_warn(dev->class_dev,
833 "mite: bug? chip claims to have %i dma channels. Setting to %i.\n",
834 mite->num_channels, MAX_MITE_DMA_CHANNELS);
835 mite->num_channels = MAX_MITE_DMA_CHANNELS;
836 }
837
838 /* get the wpdep bits and convert it to the write port fifo depth */
839 wpdep = CSIGR_TO_WPDEP(csigr_bits);
840 if (wpdep)
841 wpdep = BIT(wpdep);
842
843 dev_dbg(dev->class_dev,
844 "mite: version = %i, type = %i, mite mode = %i, interface mode = %i\n",
845 CSIGR_TO_VER(csigr_bits), CSIGR_TO_TYPE(csigr_bits),
846 CSIGR_TO_MMODE(csigr_bits), CSIGR_TO_IMODE(csigr_bits));
847 dev_dbg(dev->class_dev,
848 "mite: num channels = %i, write post fifo depth = %i, wins = %i, iowins = %i\n",
849 CSIGR_TO_DMAC(csigr_bits), wpdep,
850 CSIGR_TO_WINS(csigr_bits), CSIGR_TO_IOWINS(csigr_bits));
851
852 for (i = 0; i < mite->num_channels; i++) {
853 writel(CHOR_DMARESET, mite->mmio + MITE_CHOR(i));
854 /* disable interrupts */
855 writel(CHCR_CLR_DMA_IE | CHCR_CLR_LINKP_IE | CHCR_CLR_SAR_IE |
856 CHCR_CLR_DONE_IE | CHCR_CLR_MRDY_IE | CHCR_CLR_DRDY_IE |
857 CHCR_CLR_LC_IE | CHCR_CLR_CONT_RB_IE,
858 mite->mmio + MITE_CHCR(i));
859 }
860 mite->fifo_size = mite_fifo_size(mite, 0);
861 dev_dbg(dev->class_dev, "mite: fifo size is %i.\n", mite->fifo_size);
862 return 0;
863 }
864
865 /**
866 * mite_attach() - Allocate and initialize a MITE device for a comedi driver.
867 * @dev: COMEDI device.
868 * @use_win1: flag to use I/O Window 1 instead of I/O Window 0.
869 *
870 * Called by a COMEDI drivers (*auto_attach).
871 *
872 * Returns a pointer to the MITE device on success, or NULL if the MITE cannot
873 * be allocated or remapped.
874 */
mite_attach(struct comedi_device * dev,bool use_win1)875 struct mite *mite_attach(struct comedi_device *dev, bool use_win1)
876 {
877 struct pci_dev *pcidev = comedi_to_pci_dev(dev);
878 struct mite *mite;
879 unsigned int i;
880 int ret;
881
882 mite = kzalloc(sizeof(*mite), GFP_KERNEL);
883 if (!mite)
884 return NULL;
885
886 spin_lock_init(&mite->lock);
887 mite->pcidev = pcidev;
888 for (i = 0; i < MAX_MITE_DMA_CHANNELS; ++i) {
889 mite->channels[i].mite = mite;
890 mite->channels[i].channel = i;
891 mite->channels[i].done = 1;
892 }
893
894 ret = mite_setup(dev, mite, use_win1);
895 if (ret) {
896 if (mite->mmio)
897 iounmap(mite->mmio);
898 kfree(mite);
899 return NULL;
900 }
901
902 return mite;
903 }
904 EXPORT_SYMBOL_GPL(mite_attach);
905
906 /**
907 * mite_detach() - Unmap and free a MITE device for a comedi driver.
908 * @mite: MITE device.
909 *
910 * Called by a COMEDI drivers (*detach).
911 */
mite_detach(struct mite * mite)912 void mite_detach(struct mite *mite)
913 {
914 if (!mite)
915 return;
916
917 if (mite->mmio)
918 iounmap(mite->mmio);
919
920 kfree(mite);
921 }
922 EXPORT_SYMBOL_GPL(mite_detach);
923
mite_module_init(void)924 static int __init mite_module_init(void)
925 {
926 return 0;
927 }
928 module_init(mite_module_init);
929
mite_module_exit(void)930 static void __exit mite_module_exit(void)
931 {
932 }
933 module_exit(mite_module_exit);
934
935 MODULE_AUTHOR("Comedi https://www.comedi.org");
936 MODULE_DESCRIPTION("Comedi helper for NI Mite PCI interface chip");
937 MODULE_LICENSE("GPL");
938