1 /*
2  * Device driver for Microgate SyncLink GT serial adapters.
3  *
4  * written by Paul Fulghum for Microgate Corporation
5  * paulkf@microgate.com
6  *
7  * Microgate and SyncLink are trademarks of Microgate Corporation
8  *
9  * This code is released under the GNU General Public License (GPL)
10  *
11  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
12  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
13  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
14  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
15  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
16  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
17  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
18  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
19  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
20  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
21  * OF THE POSSIBILITY OF SUCH DAMAGE.
22  */
23 
24 /*
25  * DEBUG OUTPUT DEFINITIONS
26  *
27  * uncomment lines below to enable specific types of debug output
28  *
29  * DBGINFO   information - most verbose output
30  * DBGERR    serious errors
31  * DBGBH     bottom half service routine debugging
32  * DBGISR    interrupt service routine debugging
33  * DBGDATA   output receive and transmit data
34  * DBGTBUF   output transmit DMA buffers and registers
35  * DBGRBUF   output receive DMA buffers and registers
36  */
37 
38 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
39 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
40 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
41 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
42 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
43 /*#define DBGTBUF(info) dump_tbufs(info)*/
44 /*#define DBGRBUF(info) dump_rbufs(info)*/
45 
46 
47 #include <linux/module.h>
48 #include <linux/errno.h>
49 #include <linux/signal.h>
50 #include <linux/sched.h>
51 #include <linux/timer.h>
52 #include <linux/interrupt.h>
53 #include <linux/pci.h>
54 #include <linux/tty.h>
55 #include <linux/tty_flip.h>
56 #include <linux/serial.h>
57 #include <linux/major.h>
58 #include <linux/string.h>
59 #include <linux/fcntl.h>
60 #include <linux/ptrace.h>
61 #include <linux/ioport.h>
62 #include <linux/mm.h>
63 #include <linux/seq_file.h>
64 #include <linux/slab.h>
65 #include <linux/netdevice.h>
66 #include <linux/vmalloc.h>
67 #include <linux/init.h>
68 #include <linux/delay.h>
69 #include <linux/ioctl.h>
70 #include <linux/termios.h>
71 #include <linux/bitops.h>
72 #include <linux/workqueue.h>
73 #include <linux/hdlc.h>
74 #include <linux/synclink.h>
75 
76 #include <asm/io.h>
77 #include <asm/irq.h>
78 #include <asm/dma.h>
79 #include <asm/types.h>
80 #include <asm/uaccess.h>
81 
82 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
83 #define SYNCLINK_GENERIC_HDLC 1
84 #else
85 #define SYNCLINK_GENERIC_HDLC 0
86 #endif
87 
88 /*
89  * module identification
90  */
91 static char *driver_name     = "SyncLink GT";
92 static char *tty_driver_name = "synclink_gt";
93 static char *tty_dev_prefix  = "ttySLG";
94 MODULE_LICENSE("GPL");
95 #define MGSL_MAGIC 0x5401
96 #define MAX_DEVICES 32
97 
98 static struct pci_device_id pci_table[] = {
99 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
100 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
101 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
102 	{PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
103 	{0,}, /* terminate list */
104 };
105 MODULE_DEVICE_TABLE(pci, pci_table);
106 
107 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
108 static void remove_one(struct pci_dev *dev);
109 static struct pci_driver pci_driver = {
110 	.name		= "synclink_gt",
111 	.id_table	= pci_table,
112 	.probe		= init_one,
113 	.remove		= __devexit_p(remove_one),
114 };
115 
116 static bool pci_registered;
117 
118 /*
119  * module configuration and status
120  */
121 static struct slgt_info *slgt_device_list;
122 static int slgt_device_count;
123 
124 static int ttymajor;
125 static int debug_level;
126 static int maxframe[MAX_DEVICES];
127 
128 module_param(ttymajor, int, 0);
129 module_param(debug_level, int, 0);
130 module_param_array(maxframe, int, NULL, 0);
131 
132 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
133 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
134 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
135 
136 /*
137  * tty support and callbacks
138  */
139 static struct tty_driver *serial_driver;
140 
141 static int  open(struct tty_struct *tty, struct file * filp);
142 static void close(struct tty_struct *tty, struct file * filp);
143 static void hangup(struct tty_struct *tty);
144 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
145 
146 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
147 static int put_char(struct tty_struct *tty, unsigned char ch);
148 static void send_xchar(struct tty_struct *tty, char ch);
149 static void wait_until_sent(struct tty_struct *tty, int timeout);
150 static int  write_room(struct tty_struct *tty);
151 static void flush_chars(struct tty_struct *tty);
152 static void flush_buffer(struct tty_struct *tty);
153 static void tx_hold(struct tty_struct *tty);
154 static void tx_release(struct tty_struct *tty);
155 
156 static int  ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
157 static int  chars_in_buffer(struct tty_struct *tty);
158 static void throttle(struct tty_struct * tty);
159 static void unthrottle(struct tty_struct * tty);
160 static int set_break(struct tty_struct *tty, int break_state);
161 
162 /*
163  * generic HDLC support and callbacks
164  */
165 #if SYNCLINK_GENERIC_HDLC
166 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
167 static void hdlcdev_tx_done(struct slgt_info *info);
168 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
169 static int  hdlcdev_init(struct slgt_info *info);
170 static void hdlcdev_exit(struct slgt_info *info);
171 #endif
172 
173 
174 /*
175  * device specific structures, macros and functions
176  */
177 
178 #define SLGT_MAX_PORTS 4
179 #define SLGT_REG_SIZE  256
180 
181 /*
182  * conditional wait facility
183  */
184 struct cond_wait {
185 	struct cond_wait *next;
186 	wait_queue_head_t q;
187 	wait_queue_t wait;
188 	unsigned int data;
189 };
190 static void init_cond_wait(struct cond_wait *w, unsigned int data);
191 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
192 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
193 static void flush_cond_wait(struct cond_wait **head);
194 
195 /*
196  * DMA buffer descriptor and access macros
197  */
198 struct slgt_desc
199 {
200 	__le16 count;
201 	__le16 status;
202 	__le32 pbuf;  /* physical address of data buffer */
203 	__le32 next;  /* physical address of next descriptor */
204 
205 	/* driver book keeping */
206 	char *buf;          /* virtual  address of data buffer */
207     	unsigned int pdesc; /* physical address of this descriptor */
208 	dma_addr_t buf_dma_addr;
209 	unsigned short buf_count;
210 };
211 
212 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
213 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
214 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
215 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
216 #define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
217 #define desc_count(a)      (le16_to_cpu((a).count))
218 #define desc_status(a)     (le16_to_cpu((a).status))
219 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
220 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
221 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
222 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
223 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
224 
225 struct _input_signal_events {
226 	int ri_up;
227 	int ri_down;
228 	int dsr_up;
229 	int dsr_down;
230 	int dcd_up;
231 	int dcd_down;
232 	int cts_up;
233 	int cts_down;
234 };
235 
236 /*
237  * device instance data structure
238  */
239 struct slgt_info {
240 	void *if_ptr;		/* General purpose pointer (used by SPPP) */
241 	struct tty_port port;
242 
243 	struct slgt_info *next_device;	/* device list link */
244 
245 	int magic;
246 
247 	char device_name[25];
248 	struct pci_dev *pdev;
249 
250 	int port_count;  /* count of ports on adapter */
251 	int adapter_num; /* adapter instance number */
252 	int port_num;    /* port instance number */
253 
254 	/* array of pointers to port contexts on this adapter */
255 	struct slgt_info *port_array[SLGT_MAX_PORTS];
256 
257 	int			line;		/* tty line instance number */
258 
259 	struct mgsl_icount	icount;
260 
261 	int			timeout;
262 	int			x_char;		/* xon/xoff character */
263 	unsigned int		read_status_mask;
264 	unsigned int 		ignore_status_mask;
265 
266 	wait_queue_head_t	status_event_wait_q;
267 	wait_queue_head_t	event_wait_q;
268 	struct timer_list	tx_timer;
269 	struct timer_list	rx_timer;
270 
271 	unsigned int            gpio_present;
272 	struct cond_wait        *gpio_wait_q;
273 
274 	spinlock_t lock;	/* spinlock for synchronizing with ISR */
275 
276 	struct work_struct task;
277 	u32 pending_bh;
278 	bool bh_requested;
279 	bool bh_running;
280 
281 	int isr_overflow;
282 	bool irq_requested;	/* true if IRQ requested */
283 	bool irq_occurred;	/* for diagnostics use */
284 
285 	/* device configuration */
286 
287 	unsigned int bus_type;
288 	unsigned int irq_level;
289 	unsigned long irq_flags;
290 
291 	unsigned char __iomem * reg_addr;  /* memory mapped registers address */
292 	u32 phys_reg_addr;
293 	bool reg_addr_requested;
294 
295 	MGSL_PARAMS params;       /* communications parameters */
296 	u32 idle_mode;
297 	u32 max_frame_size;       /* as set by device config */
298 
299 	unsigned int rbuf_fill_level;
300 	unsigned int rx_pio;
301 	unsigned int if_mode;
302 	unsigned int base_clock;
303 	unsigned int xsync;
304 	unsigned int xctrl;
305 
306 	/* device status */
307 
308 	bool rx_enabled;
309 	bool rx_restart;
310 
311 	bool tx_enabled;
312 	bool tx_active;
313 
314 	unsigned char signals;    /* serial signal states */
315 	int init_error;  /* initialization error */
316 
317 	unsigned char *tx_buf;
318 	int tx_count;
319 
320 	char flag_buf[MAX_ASYNC_BUFFER_SIZE];
321 	char char_buf[MAX_ASYNC_BUFFER_SIZE];
322 	bool drop_rts_on_tx_done;
323 	struct	_input_signal_events	input_signal_events;
324 
325 	int dcd_chkcount;	/* check counts to prevent */
326 	int cts_chkcount;	/* too many IRQs if a signal */
327 	int dsr_chkcount;	/* is floating */
328 	int ri_chkcount;
329 
330 	char *bufs;		/* virtual address of DMA buffer lists */
331 	dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
332 
333 	unsigned int rbuf_count;
334 	struct slgt_desc *rbufs;
335 	unsigned int rbuf_current;
336 	unsigned int rbuf_index;
337 	unsigned int rbuf_fill_index;
338 	unsigned short rbuf_fill_count;
339 
340 	unsigned int tbuf_count;
341 	struct slgt_desc *tbufs;
342 	unsigned int tbuf_current;
343 	unsigned int tbuf_start;
344 
345 	unsigned char *tmp_rbuf;
346 	unsigned int tmp_rbuf_count;
347 
348 	/* SPPP/Cisco HDLC device parts */
349 
350 	int netcount;
351 	spinlock_t netlock;
352 #if SYNCLINK_GENERIC_HDLC
353 	struct net_device *netdev;
354 #endif
355 
356 };
357 
358 static MGSL_PARAMS default_params = {
359 	.mode            = MGSL_MODE_HDLC,
360 	.loopback        = 0,
361 	.flags           = HDLC_FLAG_UNDERRUN_ABORT15,
362 	.encoding        = HDLC_ENCODING_NRZI_SPACE,
363 	.clock_speed     = 0,
364 	.addr_filter     = 0xff,
365 	.crc_type        = HDLC_CRC_16_CCITT,
366 	.preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
367 	.preamble        = HDLC_PREAMBLE_PATTERN_NONE,
368 	.data_rate       = 9600,
369 	.data_bits       = 8,
370 	.stop_bits       = 1,
371 	.parity          = ASYNC_PARITY_NONE
372 };
373 
374 
375 #define BH_RECEIVE  1
376 #define BH_TRANSMIT 2
377 #define BH_STATUS   4
378 #define IO_PIN_SHUTDOWN_LIMIT 100
379 
380 #define DMABUFSIZE 256
381 #define DESC_LIST_SIZE 4096
382 
383 #define MASK_PARITY  BIT1
384 #define MASK_FRAMING BIT0
385 #define MASK_BREAK   BIT14
386 #define MASK_OVERRUN BIT4
387 
388 #define GSR   0x00 /* global status */
389 #define JCR   0x04 /* JTAG control */
390 #define IODR  0x08 /* GPIO direction */
391 #define IOER  0x0c /* GPIO interrupt enable */
392 #define IOVR  0x10 /* GPIO value */
393 #define IOSR  0x14 /* GPIO interrupt status */
394 #define TDR   0x80 /* tx data */
395 #define RDR   0x80 /* rx data */
396 #define TCR   0x82 /* tx control */
397 #define TIR   0x84 /* tx idle */
398 #define TPR   0x85 /* tx preamble */
399 #define RCR   0x86 /* rx control */
400 #define VCR   0x88 /* V.24 control */
401 #define CCR   0x89 /* clock control */
402 #define BDR   0x8a /* baud divisor */
403 #define SCR   0x8c /* serial control */
404 #define SSR   0x8e /* serial status */
405 #define RDCSR 0x90 /* rx DMA control/status */
406 #define TDCSR 0x94 /* tx DMA control/status */
407 #define RDDAR 0x98 /* rx DMA descriptor address */
408 #define TDDAR 0x9c /* tx DMA descriptor address */
409 #define XSR   0x40 /* extended sync pattern */
410 #define XCR   0x44 /* extended control */
411 
412 #define RXIDLE      BIT14
413 #define RXBREAK     BIT14
414 #define IRQ_TXDATA  BIT13
415 #define IRQ_TXIDLE  BIT12
416 #define IRQ_TXUNDER BIT11 /* HDLC */
417 #define IRQ_RXDATA  BIT10
418 #define IRQ_RXIDLE  BIT9  /* HDLC */
419 #define IRQ_RXBREAK BIT9  /* async */
420 #define IRQ_RXOVER  BIT8
421 #define IRQ_DSR     BIT7
422 #define IRQ_CTS     BIT6
423 #define IRQ_DCD     BIT5
424 #define IRQ_RI      BIT4
425 #define IRQ_ALL     0x3ff0
426 #define IRQ_MASTER  BIT0
427 
428 #define slgt_irq_on(info, mask) \
429 	wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
430 #define slgt_irq_off(info, mask) \
431 	wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
432 
433 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
434 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
435 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
436 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
437 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
438 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
439 
440 static void  msc_set_vcr(struct slgt_info *info);
441 
442 static int  startup(struct slgt_info *info);
443 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
444 static void shutdown(struct slgt_info *info);
445 static void program_hw(struct slgt_info *info);
446 static void change_params(struct slgt_info *info);
447 
448 static int  register_test(struct slgt_info *info);
449 static int  irq_test(struct slgt_info *info);
450 static int  loopback_test(struct slgt_info *info);
451 static int  adapter_test(struct slgt_info *info);
452 
453 static void reset_adapter(struct slgt_info *info);
454 static void reset_port(struct slgt_info *info);
455 static void async_mode(struct slgt_info *info);
456 static void sync_mode(struct slgt_info *info);
457 
458 static void rx_stop(struct slgt_info *info);
459 static void rx_start(struct slgt_info *info);
460 static void reset_rbufs(struct slgt_info *info);
461 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
462 static void rdma_reset(struct slgt_info *info);
463 static bool rx_get_frame(struct slgt_info *info);
464 static bool rx_get_buf(struct slgt_info *info);
465 
466 static void tx_start(struct slgt_info *info);
467 static void tx_stop(struct slgt_info *info);
468 static void tx_set_idle(struct slgt_info *info);
469 static unsigned int free_tbuf_count(struct slgt_info *info);
470 static unsigned int tbuf_bytes(struct slgt_info *info);
471 static void reset_tbufs(struct slgt_info *info);
472 static void tdma_reset(struct slgt_info *info);
473 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count);
474 
475 static void get_signals(struct slgt_info *info);
476 static void set_signals(struct slgt_info *info);
477 static void enable_loopback(struct slgt_info *info);
478 static void set_rate(struct slgt_info *info, u32 data_rate);
479 
480 static int  bh_action(struct slgt_info *info);
481 static void bh_handler(struct work_struct *work);
482 static void bh_transmit(struct slgt_info *info);
483 static void isr_serial(struct slgt_info *info);
484 static void isr_rdma(struct slgt_info *info);
485 static void isr_txeom(struct slgt_info *info, unsigned short status);
486 static void isr_tdma(struct slgt_info *info);
487 
488 static int  alloc_dma_bufs(struct slgt_info *info);
489 static void free_dma_bufs(struct slgt_info *info);
490 static int  alloc_desc(struct slgt_info *info);
491 static void free_desc(struct slgt_info *info);
492 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
493 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
494 
495 static int  alloc_tmp_rbuf(struct slgt_info *info);
496 static void free_tmp_rbuf(struct slgt_info *info);
497 
498 static void tx_timeout(unsigned long context);
499 static void rx_timeout(unsigned long context);
500 
501 /*
502  * ioctl handlers
503  */
504 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
505 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
506 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
507 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
508 static int  set_txidle(struct slgt_info *info, int idle_mode);
509 static int  tx_enable(struct slgt_info *info, int enable);
510 static int  tx_abort(struct slgt_info *info);
511 static int  rx_enable(struct slgt_info *info, int enable);
512 static int  modem_input_wait(struct slgt_info *info,int arg);
513 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
514 static int  tiocmget(struct tty_struct *tty);
515 static int  tiocmset(struct tty_struct *tty,
516 				unsigned int set, unsigned int clear);
517 static int set_break(struct tty_struct *tty, int break_state);
518 static int  get_interface(struct slgt_info *info, int __user *if_mode);
519 static int  set_interface(struct slgt_info *info, int if_mode);
520 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
521 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
522 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
523 static int  get_xsync(struct slgt_info *info, int __user *if_mode);
524 static int  set_xsync(struct slgt_info *info, int if_mode);
525 static int  get_xctrl(struct slgt_info *info, int __user *if_mode);
526 static int  set_xctrl(struct slgt_info *info, int if_mode);
527 
528 /*
529  * driver functions
530  */
531 static void add_device(struct slgt_info *info);
532 static void device_init(int adapter_num, struct pci_dev *pdev);
533 static int  claim_resources(struct slgt_info *info);
534 static void release_resources(struct slgt_info *info);
535 
536 /*
537  * DEBUG OUTPUT CODE
538  */
539 #ifndef DBGINFO
540 #define DBGINFO(fmt)
541 #endif
542 #ifndef DBGERR
543 #define DBGERR(fmt)
544 #endif
545 #ifndef DBGBH
546 #define DBGBH(fmt)
547 #endif
548 #ifndef DBGISR
549 #define DBGISR(fmt)
550 #endif
551 
552 #ifdef DBGDATA
trace_block(struct slgt_info * info,const char * data,int count,const char * label)553 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
554 {
555 	int i;
556 	int linecount;
557 	printk("%s %s data:\n",info->device_name, label);
558 	while(count) {
559 		linecount = (count > 16) ? 16 : count;
560 		for(i=0; i < linecount; i++)
561 			printk("%02X ",(unsigned char)data[i]);
562 		for(;i<17;i++)
563 			printk("   ");
564 		for(i=0;i<linecount;i++) {
565 			if (data[i]>=040 && data[i]<=0176)
566 				printk("%c",data[i]);
567 			else
568 				printk(".");
569 		}
570 		printk("\n");
571 		data  += linecount;
572 		count -= linecount;
573 	}
574 }
575 #else
576 #define DBGDATA(info, buf, size, label)
577 #endif
578 
579 #ifdef DBGTBUF
dump_tbufs(struct slgt_info * info)580 static void dump_tbufs(struct slgt_info *info)
581 {
582 	int i;
583 	printk("tbuf_current=%d\n", info->tbuf_current);
584 	for (i=0 ; i < info->tbuf_count ; i++) {
585 		printk("%d: count=%04X status=%04X\n",
586 			i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
587 	}
588 }
589 #else
590 #define DBGTBUF(info)
591 #endif
592 
593 #ifdef DBGRBUF
dump_rbufs(struct slgt_info * info)594 static void dump_rbufs(struct slgt_info *info)
595 {
596 	int i;
597 	printk("rbuf_current=%d\n", info->rbuf_current);
598 	for (i=0 ; i < info->rbuf_count ; i++) {
599 		printk("%d: count=%04X status=%04X\n",
600 			i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
601 	}
602 }
603 #else
604 #define DBGRBUF(info)
605 #endif
606 
sanity_check(struct slgt_info * info,char * devname,const char * name)607 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
608 {
609 #ifdef SANITY_CHECK
610 	if (!info) {
611 		printk("null struct slgt_info for (%s) in %s\n", devname, name);
612 		return 1;
613 	}
614 	if (info->magic != MGSL_MAGIC) {
615 		printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
616 		return 1;
617 	}
618 #else
619 	if (!info)
620 		return 1;
621 #endif
622 	return 0;
623 }
624 
625 /**
626  * line discipline callback wrappers
627  *
628  * The wrappers maintain line discipline references
629  * while calling into the line discipline.
630  *
631  * ldisc_receive_buf  - pass receive data to line discipline
632  */
ldisc_receive_buf(struct tty_struct * tty,const __u8 * data,char * flags,int count)633 static void ldisc_receive_buf(struct tty_struct *tty,
634 			      const __u8 *data, char *flags, int count)
635 {
636 	struct tty_ldisc *ld;
637 	if (!tty)
638 		return;
639 	ld = tty_ldisc_ref(tty);
640 	if (ld) {
641 		if (ld->ops->receive_buf)
642 			ld->ops->receive_buf(tty, data, flags, count);
643 		tty_ldisc_deref(ld);
644 	}
645 }
646 
647 /* tty callbacks */
648 
open(struct tty_struct * tty,struct file * filp)649 static int open(struct tty_struct *tty, struct file *filp)
650 {
651 	struct slgt_info *info;
652 	int retval, line;
653 	unsigned long flags;
654 
655 	line = tty->index;
656 	if (line >= slgt_device_count) {
657 		DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
658 		return -ENODEV;
659 	}
660 
661 	info = slgt_device_list;
662 	while(info && info->line != line)
663 		info = info->next_device;
664 	if (sanity_check(info, tty->name, "open"))
665 		return -ENODEV;
666 	if (info->init_error) {
667 		DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
668 		return -ENODEV;
669 	}
670 
671 	tty->driver_data = info;
672 	info->port.tty = tty;
673 
674 	DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
675 
676 	/* If port is closing, signal caller to try again */
677 	if (tty_hung_up_p(filp) || info->port.flags & ASYNC_CLOSING){
678 		if (info->port.flags & ASYNC_CLOSING)
679 			interruptible_sleep_on(&info->port.close_wait);
680 		retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
681 			-EAGAIN : -ERESTARTSYS);
682 		goto cleanup;
683 	}
684 
685 	mutex_lock(&info->port.mutex);
686 	info->port.tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
687 
688 	spin_lock_irqsave(&info->netlock, flags);
689 	if (info->netcount) {
690 		retval = -EBUSY;
691 		spin_unlock_irqrestore(&info->netlock, flags);
692 		mutex_unlock(&info->port.mutex);
693 		goto cleanup;
694 	}
695 	info->port.count++;
696 	spin_unlock_irqrestore(&info->netlock, flags);
697 
698 	if (info->port.count == 1) {
699 		/* 1st open on this device, init hardware */
700 		retval = startup(info);
701 		if (retval < 0) {
702 			mutex_unlock(&info->port.mutex);
703 			goto cleanup;
704 		}
705 	}
706 	mutex_unlock(&info->port.mutex);
707 	retval = block_til_ready(tty, filp, info);
708 	if (retval) {
709 		DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
710 		goto cleanup;
711 	}
712 
713 	retval = 0;
714 
715 cleanup:
716 	if (retval) {
717 		if (tty->count == 1)
718 			info->port.tty = NULL; /* tty layer will release tty struct */
719 		if(info->port.count)
720 			info->port.count--;
721 	}
722 
723 	DBGINFO(("%s open rc=%d\n", info->device_name, retval));
724 	return retval;
725 }
726 
close(struct tty_struct * tty,struct file * filp)727 static void close(struct tty_struct *tty, struct file *filp)
728 {
729 	struct slgt_info *info = tty->driver_data;
730 
731 	if (sanity_check(info, tty->name, "close"))
732 		return;
733 	DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
734 
735 	if (tty_port_close_start(&info->port, tty, filp) == 0)
736 		goto cleanup;
737 
738 	mutex_lock(&info->port.mutex);
739  	if (info->port.flags & ASYNC_INITIALIZED)
740  		wait_until_sent(tty, info->timeout);
741 	flush_buffer(tty);
742 	tty_ldisc_flush(tty);
743 
744 	shutdown(info);
745 	mutex_unlock(&info->port.mutex);
746 
747 	tty_port_close_end(&info->port, tty);
748 	info->port.tty = NULL;
749 cleanup:
750 	DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
751 }
752 
hangup(struct tty_struct * tty)753 static void hangup(struct tty_struct *tty)
754 {
755 	struct slgt_info *info = tty->driver_data;
756 	unsigned long flags;
757 
758 	if (sanity_check(info, tty->name, "hangup"))
759 		return;
760 	DBGINFO(("%s hangup\n", info->device_name));
761 
762 	flush_buffer(tty);
763 
764 	mutex_lock(&info->port.mutex);
765 	shutdown(info);
766 
767 	spin_lock_irqsave(&info->port.lock, flags);
768 	info->port.count = 0;
769 	info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
770 	info->port.tty = NULL;
771 	spin_unlock_irqrestore(&info->port.lock, flags);
772 	mutex_unlock(&info->port.mutex);
773 
774 	wake_up_interruptible(&info->port.open_wait);
775 }
776 
set_termios(struct tty_struct * tty,struct ktermios * old_termios)777 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
778 {
779 	struct slgt_info *info = tty->driver_data;
780 	unsigned long flags;
781 
782 	DBGINFO(("%s set_termios\n", tty->driver->name));
783 
784 	change_params(info);
785 
786 	/* Handle transition to B0 status */
787 	if (old_termios->c_cflag & CBAUD &&
788 	    !(tty->termios->c_cflag & CBAUD)) {
789 		info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
790 		spin_lock_irqsave(&info->lock,flags);
791 		set_signals(info);
792 		spin_unlock_irqrestore(&info->lock,flags);
793 	}
794 
795 	/* Handle transition away from B0 status */
796 	if (!(old_termios->c_cflag & CBAUD) &&
797 	    tty->termios->c_cflag & CBAUD) {
798 		info->signals |= SerialSignal_DTR;
799  		if (!(tty->termios->c_cflag & CRTSCTS) ||
800  		    !test_bit(TTY_THROTTLED, &tty->flags)) {
801 			info->signals |= SerialSignal_RTS;
802  		}
803 		spin_lock_irqsave(&info->lock,flags);
804 	 	set_signals(info);
805 		spin_unlock_irqrestore(&info->lock,flags);
806 	}
807 
808 	/* Handle turning off CRTSCTS */
809 	if (old_termios->c_cflag & CRTSCTS &&
810 	    !(tty->termios->c_cflag & CRTSCTS)) {
811 		tty->hw_stopped = 0;
812 		tx_release(tty);
813 	}
814 }
815 
update_tx_timer(struct slgt_info * info)816 static void update_tx_timer(struct slgt_info *info)
817 {
818 	/*
819 	 * use worst case speed of 1200bps to calculate transmit timeout
820 	 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
821 	 */
822 	if (info->params.mode == MGSL_MODE_HDLC) {
823 		int timeout  = (tbuf_bytes(info) * 7) + 1000;
824 		mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
825 	}
826 }
827 
write(struct tty_struct * tty,const unsigned char * buf,int count)828 static int write(struct tty_struct *tty,
829 		 const unsigned char *buf, int count)
830 {
831 	int ret = 0;
832 	struct slgt_info *info = tty->driver_data;
833 	unsigned long flags;
834 
835 	if (sanity_check(info, tty->name, "write"))
836 		return -EIO;
837 
838 	DBGINFO(("%s write count=%d\n", info->device_name, count));
839 
840 	if (!info->tx_buf || (count > info->max_frame_size))
841 		return -EIO;
842 
843 	if (!count || tty->stopped || tty->hw_stopped)
844 		return 0;
845 
846 	spin_lock_irqsave(&info->lock, flags);
847 
848 	if (info->tx_count) {
849 		/* send accumulated data from send_char() */
850 		if (!tx_load(info, info->tx_buf, info->tx_count))
851 			goto cleanup;
852 		info->tx_count = 0;
853 	}
854 
855 	if (tx_load(info, buf, count))
856 		ret = count;
857 
858 cleanup:
859 	spin_unlock_irqrestore(&info->lock, flags);
860 	DBGINFO(("%s write rc=%d\n", info->device_name, ret));
861 	return ret;
862 }
863 
put_char(struct tty_struct * tty,unsigned char ch)864 static int put_char(struct tty_struct *tty, unsigned char ch)
865 {
866 	struct slgt_info *info = tty->driver_data;
867 	unsigned long flags;
868 	int ret = 0;
869 
870 	if (sanity_check(info, tty->name, "put_char"))
871 		return 0;
872 	DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
873 	if (!info->tx_buf)
874 		return 0;
875 	spin_lock_irqsave(&info->lock,flags);
876 	if (info->tx_count < info->max_frame_size) {
877 		info->tx_buf[info->tx_count++] = ch;
878 		ret = 1;
879 	}
880 	spin_unlock_irqrestore(&info->lock,flags);
881 	return ret;
882 }
883 
send_xchar(struct tty_struct * tty,char ch)884 static void send_xchar(struct tty_struct *tty, char ch)
885 {
886 	struct slgt_info *info = tty->driver_data;
887 	unsigned long flags;
888 
889 	if (sanity_check(info, tty->name, "send_xchar"))
890 		return;
891 	DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
892 	info->x_char = ch;
893 	if (ch) {
894 		spin_lock_irqsave(&info->lock,flags);
895 		if (!info->tx_enabled)
896 		 	tx_start(info);
897 		spin_unlock_irqrestore(&info->lock,flags);
898 	}
899 }
900 
wait_until_sent(struct tty_struct * tty,int timeout)901 static void wait_until_sent(struct tty_struct *tty, int timeout)
902 {
903 	struct slgt_info *info = tty->driver_data;
904 	unsigned long orig_jiffies, char_time;
905 
906 	if (!info )
907 		return;
908 	if (sanity_check(info, tty->name, "wait_until_sent"))
909 		return;
910 	DBGINFO(("%s wait_until_sent entry\n", info->device_name));
911 	if (!(info->port.flags & ASYNC_INITIALIZED))
912 		goto exit;
913 
914 	orig_jiffies = jiffies;
915 
916 	/* Set check interval to 1/5 of estimated time to
917 	 * send a character, and make it at least 1. The check
918 	 * interval should also be less than the timeout.
919 	 * Note: use tight timings here to satisfy the NIST-PCTS.
920 	 */
921 
922 	if (info->params.data_rate) {
923 	       	char_time = info->timeout/(32 * 5);
924 		if (!char_time)
925 			char_time++;
926 	} else
927 		char_time = 1;
928 
929 	if (timeout)
930 		char_time = min_t(unsigned long, char_time, timeout);
931 
932 	while (info->tx_active) {
933 		msleep_interruptible(jiffies_to_msecs(char_time));
934 		if (signal_pending(current))
935 			break;
936 		if (timeout && time_after(jiffies, orig_jiffies + timeout))
937 			break;
938 	}
939 exit:
940 	DBGINFO(("%s wait_until_sent exit\n", info->device_name));
941 }
942 
write_room(struct tty_struct * tty)943 static int write_room(struct tty_struct *tty)
944 {
945 	struct slgt_info *info = tty->driver_data;
946 	int ret;
947 
948 	if (sanity_check(info, tty->name, "write_room"))
949 		return 0;
950 	ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
951 	DBGINFO(("%s write_room=%d\n", info->device_name, ret));
952 	return ret;
953 }
954 
flush_chars(struct tty_struct * tty)955 static void flush_chars(struct tty_struct *tty)
956 {
957 	struct slgt_info *info = tty->driver_data;
958 	unsigned long flags;
959 
960 	if (sanity_check(info, tty->name, "flush_chars"))
961 		return;
962 	DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
963 
964 	if (info->tx_count <= 0 || tty->stopped ||
965 	    tty->hw_stopped || !info->tx_buf)
966 		return;
967 
968 	DBGINFO(("%s flush_chars start transmit\n", info->device_name));
969 
970 	spin_lock_irqsave(&info->lock,flags);
971 	if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
972 		info->tx_count = 0;
973 	spin_unlock_irqrestore(&info->lock,flags);
974 }
975 
flush_buffer(struct tty_struct * tty)976 static void flush_buffer(struct tty_struct *tty)
977 {
978 	struct slgt_info *info = tty->driver_data;
979 	unsigned long flags;
980 
981 	if (sanity_check(info, tty->name, "flush_buffer"))
982 		return;
983 	DBGINFO(("%s flush_buffer\n", info->device_name));
984 
985 	spin_lock_irqsave(&info->lock, flags);
986 	info->tx_count = 0;
987 	spin_unlock_irqrestore(&info->lock, flags);
988 
989 	tty_wakeup(tty);
990 }
991 
992 /*
993  * throttle (stop) transmitter
994  */
tx_hold(struct tty_struct * tty)995 static void tx_hold(struct tty_struct *tty)
996 {
997 	struct slgt_info *info = tty->driver_data;
998 	unsigned long flags;
999 
1000 	if (sanity_check(info, tty->name, "tx_hold"))
1001 		return;
1002 	DBGINFO(("%s tx_hold\n", info->device_name));
1003 	spin_lock_irqsave(&info->lock,flags);
1004 	if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
1005 	 	tx_stop(info);
1006 	spin_unlock_irqrestore(&info->lock,flags);
1007 }
1008 
1009 /*
1010  * release (start) transmitter
1011  */
tx_release(struct tty_struct * tty)1012 static void tx_release(struct tty_struct *tty)
1013 {
1014 	struct slgt_info *info = tty->driver_data;
1015 	unsigned long flags;
1016 
1017 	if (sanity_check(info, tty->name, "tx_release"))
1018 		return;
1019 	DBGINFO(("%s tx_release\n", info->device_name));
1020 	spin_lock_irqsave(&info->lock, flags);
1021 	if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
1022 		info->tx_count = 0;
1023 	spin_unlock_irqrestore(&info->lock, flags);
1024 }
1025 
1026 /*
1027  * Service an IOCTL request
1028  *
1029  * Arguments
1030  *
1031  * 	tty	pointer to tty instance data
1032  * 	cmd	IOCTL command code
1033  * 	arg	command argument/context
1034  *
1035  * Return 0 if success, otherwise error code
1036  */
ioctl(struct tty_struct * tty,unsigned int cmd,unsigned long arg)1037 static int ioctl(struct tty_struct *tty,
1038 		 unsigned int cmd, unsigned long arg)
1039 {
1040 	struct slgt_info *info = tty->driver_data;
1041 	void __user *argp = (void __user *)arg;
1042 	int ret;
1043 
1044 	if (sanity_check(info, tty->name, "ioctl"))
1045 		return -ENODEV;
1046 	DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1047 
1048 	if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1049 	    (cmd != TIOCMIWAIT)) {
1050 		if (tty->flags & (1 << TTY_IO_ERROR))
1051 		    return -EIO;
1052 	}
1053 
1054 	switch (cmd) {
1055 	case MGSL_IOCWAITEVENT:
1056 		return wait_mgsl_event(info, argp);
1057 	case TIOCMIWAIT:
1058 		return modem_input_wait(info,(int)arg);
1059 	case MGSL_IOCSGPIO:
1060 		return set_gpio(info, argp);
1061 	case MGSL_IOCGGPIO:
1062 		return get_gpio(info, argp);
1063 	case MGSL_IOCWAITGPIO:
1064 		return wait_gpio(info, argp);
1065 	case MGSL_IOCGXSYNC:
1066 		return get_xsync(info, argp);
1067 	case MGSL_IOCSXSYNC:
1068 		return set_xsync(info, (int)arg);
1069 	case MGSL_IOCGXCTRL:
1070 		return get_xctrl(info, argp);
1071 	case MGSL_IOCSXCTRL:
1072 		return set_xctrl(info, (int)arg);
1073 	}
1074 	mutex_lock(&info->port.mutex);
1075 	switch (cmd) {
1076 	case MGSL_IOCGPARAMS:
1077 		ret = get_params(info, argp);
1078 		break;
1079 	case MGSL_IOCSPARAMS:
1080 		ret = set_params(info, argp);
1081 		break;
1082 	case MGSL_IOCGTXIDLE:
1083 		ret = get_txidle(info, argp);
1084 		break;
1085 	case MGSL_IOCSTXIDLE:
1086 		ret = set_txidle(info, (int)arg);
1087 		break;
1088 	case MGSL_IOCTXENABLE:
1089 		ret = tx_enable(info, (int)arg);
1090 		break;
1091 	case MGSL_IOCRXENABLE:
1092 		ret = rx_enable(info, (int)arg);
1093 		break;
1094 	case MGSL_IOCTXABORT:
1095 		ret = tx_abort(info);
1096 		break;
1097 	case MGSL_IOCGSTATS:
1098 		ret = get_stats(info, argp);
1099 		break;
1100 	case MGSL_IOCGIF:
1101 		ret = get_interface(info, argp);
1102 		break;
1103 	case MGSL_IOCSIF:
1104 		ret = set_interface(info,(int)arg);
1105 		break;
1106 	default:
1107 		ret = -ENOIOCTLCMD;
1108 	}
1109 	mutex_unlock(&info->port.mutex);
1110 	return ret;
1111 }
1112 
get_icount(struct tty_struct * tty,struct serial_icounter_struct * icount)1113 static int get_icount(struct tty_struct *tty,
1114 				struct serial_icounter_struct *icount)
1115 
1116 {
1117 	struct slgt_info *info = tty->driver_data;
1118 	struct mgsl_icount cnow;	/* kernel counter temps */
1119 	unsigned long flags;
1120 
1121 	spin_lock_irqsave(&info->lock,flags);
1122 	cnow = info->icount;
1123 	spin_unlock_irqrestore(&info->lock,flags);
1124 
1125 	icount->cts = cnow.cts;
1126 	icount->dsr = cnow.dsr;
1127 	icount->rng = cnow.rng;
1128 	icount->dcd = cnow.dcd;
1129 	icount->rx = cnow.rx;
1130 	icount->tx = cnow.tx;
1131 	icount->frame = cnow.frame;
1132 	icount->overrun = cnow.overrun;
1133 	icount->parity = cnow.parity;
1134 	icount->brk = cnow.brk;
1135 	icount->buf_overrun = cnow.buf_overrun;
1136 
1137 	return 0;
1138 }
1139 
1140 /*
1141  * support for 32 bit ioctl calls on 64 bit systems
1142  */
1143 #ifdef CONFIG_COMPAT
get_params32(struct slgt_info * info,struct MGSL_PARAMS32 __user * user_params)1144 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1145 {
1146 	struct MGSL_PARAMS32 tmp_params;
1147 
1148 	DBGINFO(("%s get_params32\n", info->device_name));
1149 	memset(&tmp_params, 0, sizeof(tmp_params));
1150 	tmp_params.mode            = (compat_ulong_t)info->params.mode;
1151 	tmp_params.loopback        = info->params.loopback;
1152 	tmp_params.flags           = info->params.flags;
1153 	tmp_params.encoding        = info->params.encoding;
1154 	tmp_params.clock_speed     = (compat_ulong_t)info->params.clock_speed;
1155 	tmp_params.addr_filter     = info->params.addr_filter;
1156 	tmp_params.crc_type        = info->params.crc_type;
1157 	tmp_params.preamble_length = info->params.preamble_length;
1158 	tmp_params.preamble        = info->params.preamble;
1159 	tmp_params.data_rate       = (compat_ulong_t)info->params.data_rate;
1160 	tmp_params.data_bits       = info->params.data_bits;
1161 	tmp_params.stop_bits       = info->params.stop_bits;
1162 	tmp_params.parity          = info->params.parity;
1163 	if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1164 		return -EFAULT;
1165 	return 0;
1166 }
1167 
set_params32(struct slgt_info * info,struct MGSL_PARAMS32 __user * new_params)1168 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1169 {
1170 	struct MGSL_PARAMS32 tmp_params;
1171 
1172 	DBGINFO(("%s set_params32\n", info->device_name));
1173 	if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1174 		return -EFAULT;
1175 
1176 	spin_lock(&info->lock);
1177 	if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
1178 		info->base_clock = tmp_params.clock_speed;
1179 	} else {
1180 		info->params.mode            = tmp_params.mode;
1181 		info->params.loopback        = tmp_params.loopback;
1182 		info->params.flags           = tmp_params.flags;
1183 		info->params.encoding        = tmp_params.encoding;
1184 		info->params.clock_speed     = tmp_params.clock_speed;
1185 		info->params.addr_filter     = tmp_params.addr_filter;
1186 		info->params.crc_type        = tmp_params.crc_type;
1187 		info->params.preamble_length = tmp_params.preamble_length;
1188 		info->params.preamble        = tmp_params.preamble;
1189 		info->params.data_rate       = tmp_params.data_rate;
1190 		info->params.data_bits       = tmp_params.data_bits;
1191 		info->params.stop_bits       = tmp_params.stop_bits;
1192 		info->params.parity          = tmp_params.parity;
1193 	}
1194 	spin_unlock(&info->lock);
1195 
1196 	program_hw(info);
1197 
1198 	return 0;
1199 }
1200 
slgt_compat_ioctl(struct tty_struct * tty,unsigned int cmd,unsigned long arg)1201 static long slgt_compat_ioctl(struct tty_struct *tty,
1202 			 unsigned int cmd, unsigned long arg)
1203 {
1204 	struct slgt_info *info = tty->driver_data;
1205 	int rc = -ENOIOCTLCMD;
1206 
1207 	if (sanity_check(info, tty->name, "compat_ioctl"))
1208 		return -ENODEV;
1209 	DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1210 
1211 	switch (cmd) {
1212 
1213 	case MGSL_IOCSPARAMS32:
1214 		rc = set_params32(info, compat_ptr(arg));
1215 		break;
1216 
1217 	case MGSL_IOCGPARAMS32:
1218 		rc = get_params32(info, compat_ptr(arg));
1219 		break;
1220 
1221 	case MGSL_IOCGPARAMS:
1222 	case MGSL_IOCSPARAMS:
1223 	case MGSL_IOCGTXIDLE:
1224 	case MGSL_IOCGSTATS:
1225 	case MGSL_IOCWAITEVENT:
1226 	case MGSL_IOCGIF:
1227 	case MGSL_IOCSGPIO:
1228 	case MGSL_IOCGGPIO:
1229 	case MGSL_IOCWAITGPIO:
1230 	case MGSL_IOCGXSYNC:
1231 	case MGSL_IOCGXCTRL:
1232 	case MGSL_IOCSTXIDLE:
1233 	case MGSL_IOCTXENABLE:
1234 	case MGSL_IOCRXENABLE:
1235 	case MGSL_IOCTXABORT:
1236 	case TIOCMIWAIT:
1237 	case MGSL_IOCSIF:
1238 	case MGSL_IOCSXSYNC:
1239 	case MGSL_IOCSXCTRL:
1240 		rc = ioctl(tty, cmd, arg);
1241 		break;
1242 	}
1243 
1244 	DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1245 	return rc;
1246 }
1247 #else
1248 #define slgt_compat_ioctl NULL
1249 #endif /* ifdef CONFIG_COMPAT */
1250 
1251 /*
1252  * proc fs support
1253  */
line_info(struct seq_file * m,struct slgt_info * info)1254 static inline void line_info(struct seq_file *m, struct slgt_info *info)
1255 {
1256 	char stat_buf[30];
1257 	unsigned long flags;
1258 
1259 	seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1260 		      info->device_name, info->phys_reg_addr,
1261 		      info->irq_level, info->max_frame_size);
1262 
1263 	/* output current serial signal states */
1264 	spin_lock_irqsave(&info->lock,flags);
1265 	get_signals(info);
1266 	spin_unlock_irqrestore(&info->lock,flags);
1267 
1268 	stat_buf[0] = 0;
1269 	stat_buf[1] = 0;
1270 	if (info->signals & SerialSignal_RTS)
1271 		strcat(stat_buf, "|RTS");
1272 	if (info->signals & SerialSignal_CTS)
1273 		strcat(stat_buf, "|CTS");
1274 	if (info->signals & SerialSignal_DTR)
1275 		strcat(stat_buf, "|DTR");
1276 	if (info->signals & SerialSignal_DSR)
1277 		strcat(stat_buf, "|DSR");
1278 	if (info->signals & SerialSignal_DCD)
1279 		strcat(stat_buf, "|CD");
1280 	if (info->signals & SerialSignal_RI)
1281 		strcat(stat_buf, "|RI");
1282 
1283 	if (info->params.mode != MGSL_MODE_ASYNC) {
1284 		seq_printf(m, "\tHDLC txok:%d rxok:%d",
1285 			       info->icount.txok, info->icount.rxok);
1286 		if (info->icount.txunder)
1287 			seq_printf(m, " txunder:%d", info->icount.txunder);
1288 		if (info->icount.txabort)
1289 			seq_printf(m, " txabort:%d", info->icount.txabort);
1290 		if (info->icount.rxshort)
1291 			seq_printf(m, " rxshort:%d", info->icount.rxshort);
1292 		if (info->icount.rxlong)
1293 			seq_printf(m, " rxlong:%d", info->icount.rxlong);
1294 		if (info->icount.rxover)
1295 			seq_printf(m, " rxover:%d", info->icount.rxover);
1296 		if (info->icount.rxcrc)
1297 			seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
1298 	} else {
1299 		seq_printf(m, "\tASYNC tx:%d rx:%d",
1300 			       info->icount.tx, info->icount.rx);
1301 		if (info->icount.frame)
1302 			seq_printf(m, " fe:%d", info->icount.frame);
1303 		if (info->icount.parity)
1304 			seq_printf(m, " pe:%d", info->icount.parity);
1305 		if (info->icount.brk)
1306 			seq_printf(m, " brk:%d", info->icount.brk);
1307 		if (info->icount.overrun)
1308 			seq_printf(m, " oe:%d", info->icount.overrun);
1309 	}
1310 
1311 	/* Append serial signal status to end */
1312 	seq_printf(m, " %s\n", stat_buf+1);
1313 
1314 	seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1315 		       info->tx_active,info->bh_requested,info->bh_running,
1316 		       info->pending_bh);
1317 }
1318 
1319 /* Called to print information about devices
1320  */
synclink_gt_proc_show(struct seq_file * m,void * v)1321 static int synclink_gt_proc_show(struct seq_file *m, void *v)
1322 {
1323 	struct slgt_info *info;
1324 
1325 	seq_puts(m, "synclink_gt driver\n");
1326 
1327 	info = slgt_device_list;
1328 	while( info ) {
1329 		line_info(m, info);
1330 		info = info->next_device;
1331 	}
1332 	return 0;
1333 }
1334 
synclink_gt_proc_open(struct inode * inode,struct file * file)1335 static int synclink_gt_proc_open(struct inode *inode, struct file *file)
1336 {
1337 	return single_open(file, synclink_gt_proc_show, NULL);
1338 }
1339 
1340 static const struct file_operations synclink_gt_proc_fops = {
1341 	.owner		= THIS_MODULE,
1342 	.open		= synclink_gt_proc_open,
1343 	.read		= seq_read,
1344 	.llseek		= seq_lseek,
1345 	.release	= single_release,
1346 };
1347 
1348 /*
1349  * return count of bytes in transmit buffer
1350  */
chars_in_buffer(struct tty_struct * tty)1351 static int chars_in_buffer(struct tty_struct *tty)
1352 {
1353 	struct slgt_info *info = tty->driver_data;
1354 	int count;
1355 	if (sanity_check(info, tty->name, "chars_in_buffer"))
1356 		return 0;
1357 	count = tbuf_bytes(info);
1358 	DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1359 	return count;
1360 }
1361 
1362 /*
1363  * signal remote device to throttle send data (our receive data)
1364  */
throttle(struct tty_struct * tty)1365 static void throttle(struct tty_struct * tty)
1366 {
1367 	struct slgt_info *info = tty->driver_data;
1368 	unsigned long flags;
1369 
1370 	if (sanity_check(info, tty->name, "throttle"))
1371 		return;
1372 	DBGINFO(("%s throttle\n", info->device_name));
1373 	if (I_IXOFF(tty))
1374 		send_xchar(tty, STOP_CHAR(tty));
1375  	if (tty->termios->c_cflag & CRTSCTS) {
1376 		spin_lock_irqsave(&info->lock,flags);
1377 		info->signals &= ~SerialSignal_RTS;
1378 	 	set_signals(info);
1379 		spin_unlock_irqrestore(&info->lock,flags);
1380 	}
1381 }
1382 
1383 /*
1384  * signal remote device to stop throttling send data (our receive data)
1385  */
unthrottle(struct tty_struct * tty)1386 static void unthrottle(struct tty_struct * tty)
1387 {
1388 	struct slgt_info *info = tty->driver_data;
1389 	unsigned long flags;
1390 
1391 	if (sanity_check(info, tty->name, "unthrottle"))
1392 		return;
1393 	DBGINFO(("%s unthrottle\n", info->device_name));
1394 	if (I_IXOFF(tty)) {
1395 		if (info->x_char)
1396 			info->x_char = 0;
1397 		else
1398 			send_xchar(tty, START_CHAR(tty));
1399 	}
1400  	if (tty->termios->c_cflag & CRTSCTS) {
1401 		spin_lock_irqsave(&info->lock,flags);
1402 		info->signals |= SerialSignal_RTS;
1403 	 	set_signals(info);
1404 		spin_unlock_irqrestore(&info->lock,flags);
1405 	}
1406 }
1407 
1408 /*
1409  * set or clear transmit break condition
1410  * break_state	-1=set break condition, 0=clear
1411  */
set_break(struct tty_struct * tty,int break_state)1412 static int set_break(struct tty_struct *tty, int break_state)
1413 {
1414 	struct slgt_info *info = tty->driver_data;
1415 	unsigned short value;
1416 	unsigned long flags;
1417 
1418 	if (sanity_check(info, tty->name, "set_break"))
1419 		return -EINVAL;
1420 	DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1421 
1422 	spin_lock_irqsave(&info->lock,flags);
1423 	value = rd_reg16(info, TCR);
1424  	if (break_state == -1)
1425 		value |= BIT6;
1426 	else
1427 		value &= ~BIT6;
1428 	wr_reg16(info, TCR, value);
1429 	spin_unlock_irqrestore(&info->lock,flags);
1430 	return 0;
1431 }
1432 
1433 #if SYNCLINK_GENERIC_HDLC
1434 
1435 /**
1436  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1437  * set encoding and frame check sequence (FCS) options
1438  *
1439  * dev       pointer to network device structure
1440  * encoding  serial encoding setting
1441  * parity    FCS setting
1442  *
1443  * returns 0 if success, otherwise error code
1444  */
hdlcdev_attach(struct net_device * dev,unsigned short encoding,unsigned short parity)1445 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1446 			  unsigned short parity)
1447 {
1448 	struct slgt_info *info = dev_to_port(dev);
1449 	unsigned char  new_encoding;
1450 	unsigned short new_crctype;
1451 
1452 	/* return error if TTY interface open */
1453 	if (info->port.count)
1454 		return -EBUSY;
1455 
1456 	DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1457 
1458 	switch (encoding)
1459 	{
1460 	case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1461 	case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1462 	case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1463 	case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1464 	case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1465 	default: return -EINVAL;
1466 	}
1467 
1468 	switch (parity)
1469 	{
1470 	case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1471 	case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1472 	case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1473 	default: return -EINVAL;
1474 	}
1475 
1476 	info->params.encoding = new_encoding;
1477 	info->params.crc_type = new_crctype;
1478 
1479 	/* if network interface up, reprogram hardware */
1480 	if (info->netcount)
1481 		program_hw(info);
1482 
1483 	return 0;
1484 }
1485 
1486 /**
1487  * called by generic HDLC layer to send frame
1488  *
1489  * skb  socket buffer containing HDLC frame
1490  * dev  pointer to network device structure
1491  */
hdlcdev_xmit(struct sk_buff * skb,struct net_device * dev)1492 static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
1493 				      struct net_device *dev)
1494 {
1495 	struct slgt_info *info = dev_to_port(dev);
1496 	unsigned long flags;
1497 
1498 	DBGINFO(("%s hdlc_xmit\n", dev->name));
1499 
1500 	if (!skb->len)
1501 		return NETDEV_TX_OK;
1502 
1503 	/* stop sending until this frame completes */
1504 	netif_stop_queue(dev);
1505 
1506 	/* update network statistics */
1507 	dev->stats.tx_packets++;
1508 	dev->stats.tx_bytes += skb->len;
1509 
1510 	/* save start time for transmit timeout detection */
1511 	dev->trans_start = jiffies;
1512 
1513 	spin_lock_irqsave(&info->lock, flags);
1514 	tx_load(info, skb->data, skb->len);
1515 	spin_unlock_irqrestore(&info->lock, flags);
1516 
1517 	/* done with socket buffer, so free it */
1518 	dev_kfree_skb(skb);
1519 
1520 	return NETDEV_TX_OK;
1521 }
1522 
1523 /**
1524  * called by network layer when interface enabled
1525  * claim resources and initialize hardware
1526  *
1527  * dev  pointer to network device structure
1528  *
1529  * returns 0 if success, otherwise error code
1530  */
hdlcdev_open(struct net_device * dev)1531 static int hdlcdev_open(struct net_device *dev)
1532 {
1533 	struct slgt_info *info = dev_to_port(dev);
1534 	int rc;
1535 	unsigned long flags;
1536 
1537 	if (!try_module_get(THIS_MODULE))
1538 		return -EBUSY;
1539 
1540 	DBGINFO(("%s hdlcdev_open\n", dev->name));
1541 
1542 	/* generic HDLC layer open processing */
1543 	if ((rc = hdlc_open(dev)))
1544 		return rc;
1545 
1546 	/* arbitrate between network and tty opens */
1547 	spin_lock_irqsave(&info->netlock, flags);
1548 	if (info->port.count != 0 || info->netcount != 0) {
1549 		DBGINFO(("%s hdlc_open busy\n", dev->name));
1550 		spin_unlock_irqrestore(&info->netlock, flags);
1551 		return -EBUSY;
1552 	}
1553 	info->netcount=1;
1554 	spin_unlock_irqrestore(&info->netlock, flags);
1555 
1556 	/* claim resources and init adapter */
1557 	if ((rc = startup(info)) != 0) {
1558 		spin_lock_irqsave(&info->netlock, flags);
1559 		info->netcount=0;
1560 		spin_unlock_irqrestore(&info->netlock, flags);
1561 		return rc;
1562 	}
1563 
1564 	/* assert DTR and RTS, apply hardware settings */
1565 	info->signals |= SerialSignal_RTS + SerialSignal_DTR;
1566 	program_hw(info);
1567 
1568 	/* enable network layer transmit */
1569 	dev->trans_start = jiffies;
1570 	netif_start_queue(dev);
1571 
1572 	/* inform generic HDLC layer of current DCD status */
1573 	spin_lock_irqsave(&info->lock, flags);
1574 	get_signals(info);
1575 	spin_unlock_irqrestore(&info->lock, flags);
1576 	if (info->signals & SerialSignal_DCD)
1577 		netif_carrier_on(dev);
1578 	else
1579 		netif_carrier_off(dev);
1580 	return 0;
1581 }
1582 
1583 /**
1584  * called by network layer when interface is disabled
1585  * shutdown hardware and release resources
1586  *
1587  * dev  pointer to network device structure
1588  *
1589  * returns 0 if success, otherwise error code
1590  */
hdlcdev_close(struct net_device * dev)1591 static int hdlcdev_close(struct net_device *dev)
1592 {
1593 	struct slgt_info *info = dev_to_port(dev);
1594 	unsigned long flags;
1595 
1596 	DBGINFO(("%s hdlcdev_close\n", dev->name));
1597 
1598 	netif_stop_queue(dev);
1599 
1600 	/* shutdown adapter and release resources */
1601 	shutdown(info);
1602 
1603 	hdlc_close(dev);
1604 
1605 	spin_lock_irqsave(&info->netlock, flags);
1606 	info->netcount=0;
1607 	spin_unlock_irqrestore(&info->netlock, flags);
1608 
1609 	module_put(THIS_MODULE);
1610 	return 0;
1611 }
1612 
1613 /**
1614  * called by network layer to process IOCTL call to network device
1615  *
1616  * dev  pointer to network device structure
1617  * ifr  pointer to network interface request structure
1618  * cmd  IOCTL command code
1619  *
1620  * returns 0 if success, otherwise error code
1621  */
hdlcdev_ioctl(struct net_device * dev,struct ifreq * ifr,int cmd)1622 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1623 {
1624 	const size_t size = sizeof(sync_serial_settings);
1625 	sync_serial_settings new_line;
1626 	sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1627 	struct slgt_info *info = dev_to_port(dev);
1628 	unsigned int flags;
1629 
1630 	DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1631 
1632 	/* return error if TTY interface open */
1633 	if (info->port.count)
1634 		return -EBUSY;
1635 
1636 	if (cmd != SIOCWANDEV)
1637 		return hdlc_ioctl(dev, ifr, cmd);
1638 
1639 	memset(&new_line, 0, sizeof(new_line));
1640 
1641 	switch(ifr->ifr_settings.type) {
1642 	case IF_GET_IFACE: /* return current sync_serial_settings */
1643 
1644 		ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1645 		if (ifr->ifr_settings.size < size) {
1646 			ifr->ifr_settings.size = size; /* data size wanted */
1647 			return -ENOBUFS;
1648 		}
1649 
1650 		flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1651 					      HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1652 					      HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1653 					      HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1654 
1655 		switch (flags){
1656 		case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1657 		case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1658 		case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1659 		case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1660 		default: new_line.clock_type = CLOCK_DEFAULT;
1661 		}
1662 
1663 		new_line.clock_rate = info->params.clock_speed;
1664 		new_line.loopback   = info->params.loopback ? 1:0;
1665 
1666 		if (copy_to_user(line, &new_line, size))
1667 			return -EFAULT;
1668 		return 0;
1669 
1670 	case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1671 
1672 		if(!capable(CAP_NET_ADMIN))
1673 			return -EPERM;
1674 		if (copy_from_user(&new_line, line, size))
1675 			return -EFAULT;
1676 
1677 		switch (new_line.clock_type)
1678 		{
1679 		case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1680 		case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1681 		case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1682 		case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1683 		case CLOCK_DEFAULT:  flags = info->params.flags &
1684 					     (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1685 					      HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1686 					      HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1687 					      HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1688 		default: return -EINVAL;
1689 		}
1690 
1691 		if (new_line.loopback != 0 && new_line.loopback != 1)
1692 			return -EINVAL;
1693 
1694 		info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1695 					HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1696 					HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1697 					HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1698 		info->params.flags |= flags;
1699 
1700 		info->params.loopback = new_line.loopback;
1701 
1702 		if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1703 			info->params.clock_speed = new_line.clock_rate;
1704 		else
1705 			info->params.clock_speed = 0;
1706 
1707 		/* if network interface up, reprogram hardware */
1708 		if (info->netcount)
1709 			program_hw(info);
1710 		return 0;
1711 
1712 	default:
1713 		return hdlc_ioctl(dev, ifr, cmd);
1714 	}
1715 }
1716 
1717 /**
1718  * called by network layer when transmit timeout is detected
1719  *
1720  * dev  pointer to network device structure
1721  */
hdlcdev_tx_timeout(struct net_device * dev)1722 static void hdlcdev_tx_timeout(struct net_device *dev)
1723 {
1724 	struct slgt_info *info = dev_to_port(dev);
1725 	unsigned long flags;
1726 
1727 	DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1728 
1729 	dev->stats.tx_errors++;
1730 	dev->stats.tx_aborted_errors++;
1731 
1732 	spin_lock_irqsave(&info->lock,flags);
1733 	tx_stop(info);
1734 	spin_unlock_irqrestore(&info->lock,flags);
1735 
1736 	netif_wake_queue(dev);
1737 }
1738 
1739 /**
1740  * called by device driver when transmit completes
1741  * reenable network layer transmit if stopped
1742  *
1743  * info  pointer to device instance information
1744  */
hdlcdev_tx_done(struct slgt_info * info)1745 static void hdlcdev_tx_done(struct slgt_info *info)
1746 {
1747 	if (netif_queue_stopped(info->netdev))
1748 		netif_wake_queue(info->netdev);
1749 }
1750 
1751 /**
1752  * called by device driver when frame received
1753  * pass frame to network layer
1754  *
1755  * info  pointer to device instance information
1756  * buf   pointer to buffer contianing frame data
1757  * size  count of data bytes in buf
1758  */
hdlcdev_rx(struct slgt_info * info,char * buf,int size)1759 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1760 {
1761 	struct sk_buff *skb = dev_alloc_skb(size);
1762 	struct net_device *dev = info->netdev;
1763 
1764 	DBGINFO(("%s hdlcdev_rx\n", dev->name));
1765 
1766 	if (skb == NULL) {
1767 		DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1768 		dev->stats.rx_dropped++;
1769 		return;
1770 	}
1771 
1772 	memcpy(skb_put(skb, size), buf, size);
1773 
1774 	skb->protocol = hdlc_type_trans(skb, dev);
1775 
1776 	dev->stats.rx_packets++;
1777 	dev->stats.rx_bytes += size;
1778 
1779 	netif_rx(skb);
1780 }
1781 
1782 static const struct net_device_ops hdlcdev_ops = {
1783 	.ndo_open       = hdlcdev_open,
1784 	.ndo_stop       = hdlcdev_close,
1785 	.ndo_change_mtu = hdlc_change_mtu,
1786 	.ndo_start_xmit = hdlc_start_xmit,
1787 	.ndo_do_ioctl   = hdlcdev_ioctl,
1788 	.ndo_tx_timeout = hdlcdev_tx_timeout,
1789 };
1790 
1791 /**
1792  * called by device driver when adding device instance
1793  * do generic HDLC initialization
1794  *
1795  * info  pointer to device instance information
1796  *
1797  * returns 0 if success, otherwise error code
1798  */
hdlcdev_init(struct slgt_info * info)1799 static int hdlcdev_init(struct slgt_info *info)
1800 {
1801 	int rc;
1802 	struct net_device *dev;
1803 	hdlc_device *hdlc;
1804 
1805 	/* allocate and initialize network and HDLC layer objects */
1806 
1807 	if (!(dev = alloc_hdlcdev(info))) {
1808 		printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1809 		return -ENOMEM;
1810 	}
1811 
1812 	/* for network layer reporting purposes only */
1813 	dev->mem_start = info->phys_reg_addr;
1814 	dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1815 	dev->irq       = info->irq_level;
1816 
1817 	/* network layer callbacks and settings */
1818 	dev->netdev_ops	    = &hdlcdev_ops;
1819 	dev->watchdog_timeo = 10 * HZ;
1820 	dev->tx_queue_len   = 50;
1821 
1822 	/* generic HDLC layer callbacks and settings */
1823 	hdlc         = dev_to_hdlc(dev);
1824 	hdlc->attach = hdlcdev_attach;
1825 	hdlc->xmit   = hdlcdev_xmit;
1826 
1827 	/* register objects with HDLC layer */
1828 	if ((rc = register_hdlc_device(dev))) {
1829 		printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1830 		free_netdev(dev);
1831 		return rc;
1832 	}
1833 
1834 	info->netdev = dev;
1835 	return 0;
1836 }
1837 
1838 /**
1839  * called by device driver when removing device instance
1840  * do generic HDLC cleanup
1841  *
1842  * info  pointer to device instance information
1843  */
hdlcdev_exit(struct slgt_info * info)1844 static void hdlcdev_exit(struct slgt_info *info)
1845 {
1846 	unregister_hdlc_device(info->netdev);
1847 	free_netdev(info->netdev);
1848 	info->netdev = NULL;
1849 }
1850 
1851 #endif /* ifdef CONFIG_HDLC */
1852 
1853 /*
1854  * get async data from rx DMA buffers
1855  */
rx_async(struct slgt_info * info)1856 static void rx_async(struct slgt_info *info)
1857 {
1858  	struct tty_struct *tty = info->port.tty;
1859  	struct mgsl_icount *icount = &info->icount;
1860 	unsigned int start, end;
1861 	unsigned char *p;
1862 	unsigned char status;
1863 	struct slgt_desc *bufs = info->rbufs;
1864 	int i, count;
1865 	int chars = 0;
1866 	int stat;
1867 	unsigned char ch;
1868 
1869 	start = end = info->rbuf_current;
1870 
1871 	while(desc_complete(bufs[end])) {
1872 		count = desc_count(bufs[end]) - info->rbuf_index;
1873 		p     = bufs[end].buf + info->rbuf_index;
1874 
1875 		DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1876 		DBGDATA(info, p, count, "rx");
1877 
1878 		for(i=0 ; i < count; i+=2, p+=2) {
1879 			ch = *p;
1880 			icount->rx++;
1881 
1882 			stat = 0;
1883 
1884 			if ((status = *(p+1) & (BIT1 + BIT0))) {
1885 				if (status & BIT1)
1886 					icount->parity++;
1887 				else if (status & BIT0)
1888 					icount->frame++;
1889 				/* discard char if tty control flags say so */
1890 				if (status & info->ignore_status_mask)
1891 					continue;
1892 				if (status & BIT1)
1893 					stat = TTY_PARITY;
1894 				else if (status & BIT0)
1895 					stat = TTY_FRAME;
1896 			}
1897 			if (tty) {
1898 				tty_insert_flip_char(tty, ch, stat);
1899 				chars++;
1900 			}
1901 		}
1902 
1903 		if (i < count) {
1904 			/* receive buffer not completed */
1905 			info->rbuf_index += i;
1906 			mod_timer(&info->rx_timer, jiffies + 1);
1907 			break;
1908 		}
1909 
1910 		info->rbuf_index = 0;
1911 		free_rbufs(info, end, end);
1912 
1913 		if (++end == info->rbuf_count)
1914 			end = 0;
1915 
1916 		/* if entire list searched then no frame available */
1917 		if (end == start)
1918 			break;
1919 	}
1920 
1921 	if (tty && chars)
1922 		tty_flip_buffer_push(tty);
1923 }
1924 
1925 /*
1926  * return next bottom half action to perform
1927  */
bh_action(struct slgt_info * info)1928 static int bh_action(struct slgt_info *info)
1929 {
1930 	unsigned long flags;
1931 	int rc;
1932 
1933 	spin_lock_irqsave(&info->lock,flags);
1934 
1935 	if (info->pending_bh & BH_RECEIVE) {
1936 		info->pending_bh &= ~BH_RECEIVE;
1937 		rc = BH_RECEIVE;
1938 	} else if (info->pending_bh & BH_TRANSMIT) {
1939 		info->pending_bh &= ~BH_TRANSMIT;
1940 		rc = BH_TRANSMIT;
1941 	} else if (info->pending_bh & BH_STATUS) {
1942 		info->pending_bh &= ~BH_STATUS;
1943 		rc = BH_STATUS;
1944 	} else {
1945 		/* Mark BH routine as complete */
1946 		info->bh_running = false;
1947 		info->bh_requested = false;
1948 		rc = 0;
1949 	}
1950 
1951 	spin_unlock_irqrestore(&info->lock,flags);
1952 
1953 	return rc;
1954 }
1955 
1956 /*
1957  * perform bottom half processing
1958  */
bh_handler(struct work_struct * work)1959 static void bh_handler(struct work_struct *work)
1960 {
1961 	struct slgt_info *info = container_of(work, struct slgt_info, task);
1962 	int action;
1963 
1964 	if (!info)
1965 		return;
1966 	info->bh_running = true;
1967 
1968 	while((action = bh_action(info))) {
1969 		switch (action) {
1970 		case BH_RECEIVE:
1971 			DBGBH(("%s bh receive\n", info->device_name));
1972 			switch(info->params.mode) {
1973 			case MGSL_MODE_ASYNC:
1974 				rx_async(info);
1975 				break;
1976 			case MGSL_MODE_HDLC:
1977 				while(rx_get_frame(info));
1978 				break;
1979 			case MGSL_MODE_RAW:
1980 			case MGSL_MODE_MONOSYNC:
1981 			case MGSL_MODE_BISYNC:
1982 			case MGSL_MODE_XSYNC:
1983 				while(rx_get_buf(info));
1984 				break;
1985 			}
1986 			/* restart receiver if rx DMA buffers exhausted */
1987 			if (info->rx_restart)
1988 				rx_start(info);
1989 			break;
1990 		case BH_TRANSMIT:
1991 			bh_transmit(info);
1992 			break;
1993 		case BH_STATUS:
1994 			DBGBH(("%s bh status\n", info->device_name));
1995 			info->ri_chkcount = 0;
1996 			info->dsr_chkcount = 0;
1997 			info->dcd_chkcount = 0;
1998 			info->cts_chkcount = 0;
1999 			break;
2000 		default:
2001 			DBGBH(("%s unknown action\n", info->device_name));
2002 			break;
2003 		}
2004 	}
2005 	DBGBH(("%s bh_handler exit\n", info->device_name));
2006 }
2007 
bh_transmit(struct slgt_info * info)2008 static void bh_transmit(struct slgt_info *info)
2009 {
2010 	struct tty_struct *tty = info->port.tty;
2011 
2012 	DBGBH(("%s bh_transmit\n", info->device_name));
2013 	if (tty)
2014 		tty_wakeup(tty);
2015 }
2016 
dsr_change(struct slgt_info * info,unsigned short status)2017 static void dsr_change(struct slgt_info *info, unsigned short status)
2018 {
2019 	if (status & BIT3) {
2020 		info->signals |= SerialSignal_DSR;
2021 		info->input_signal_events.dsr_up++;
2022 	} else {
2023 		info->signals &= ~SerialSignal_DSR;
2024 		info->input_signal_events.dsr_down++;
2025 	}
2026 	DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
2027 	if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2028 		slgt_irq_off(info, IRQ_DSR);
2029 		return;
2030 	}
2031 	info->icount.dsr++;
2032 	wake_up_interruptible(&info->status_event_wait_q);
2033 	wake_up_interruptible(&info->event_wait_q);
2034 	info->pending_bh |= BH_STATUS;
2035 }
2036 
cts_change(struct slgt_info * info,unsigned short status)2037 static void cts_change(struct slgt_info *info, unsigned short status)
2038 {
2039 	if (status & BIT2) {
2040 		info->signals |= SerialSignal_CTS;
2041 		info->input_signal_events.cts_up++;
2042 	} else {
2043 		info->signals &= ~SerialSignal_CTS;
2044 		info->input_signal_events.cts_down++;
2045 	}
2046 	DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2047 	if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2048 		slgt_irq_off(info, IRQ_CTS);
2049 		return;
2050 	}
2051 	info->icount.cts++;
2052 	wake_up_interruptible(&info->status_event_wait_q);
2053 	wake_up_interruptible(&info->event_wait_q);
2054 	info->pending_bh |= BH_STATUS;
2055 
2056 	if (info->port.flags & ASYNC_CTS_FLOW) {
2057 		if (info->port.tty) {
2058 			if (info->port.tty->hw_stopped) {
2059 				if (info->signals & SerialSignal_CTS) {
2060 		 			info->port.tty->hw_stopped = 0;
2061 					info->pending_bh |= BH_TRANSMIT;
2062 					return;
2063 				}
2064 			} else {
2065 				if (!(info->signals & SerialSignal_CTS))
2066 		 			info->port.tty->hw_stopped = 1;
2067 			}
2068 		}
2069 	}
2070 }
2071 
dcd_change(struct slgt_info * info,unsigned short status)2072 static void dcd_change(struct slgt_info *info, unsigned short status)
2073 {
2074 	if (status & BIT1) {
2075 		info->signals |= SerialSignal_DCD;
2076 		info->input_signal_events.dcd_up++;
2077 	} else {
2078 		info->signals &= ~SerialSignal_DCD;
2079 		info->input_signal_events.dcd_down++;
2080 	}
2081 	DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2082 	if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2083 		slgt_irq_off(info, IRQ_DCD);
2084 		return;
2085 	}
2086 	info->icount.dcd++;
2087 #if SYNCLINK_GENERIC_HDLC
2088 	if (info->netcount) {
2089 		if (info->signals & SerialSignal_DCD)
2090 			netif_carrier_on(info->netdev);
2091 		else
2092 			netif_carrier_off(info->netdev);
2093 	}
2094 #endif
2095 	wake_up_interruptible(&info->status_event_wait_q);
2096 	wake_up_interruptible(&info->event_wait_q);
2097 	info->pending_bh |= BH_STATUS;
2098 
2099 	if (info->port.flags & ASYNC_CHECK_CD) {
2100 		if (info->signals & SerialSignal_DCD)
2101 			wake_up_interruptible(&info->port.open_wait);
2102 		else {
2103 			if (info->port.tty)
2104 				tty_hangup(info->port.tty);
2105 		}
2106 	}
2107 }
2108 
ri_change(struct slgt_info * info,unsigned short status)2109 static void ri_change(struct slgt_info *info, unsigned short status)
2110 {
2111 	if (status & BIT0) {
2112 		info->signals |= SerialSignal_RI;
2113 		info->input_signal_events.ri_up++;
2114 	} else {
2115 		info->signals &= ~SerialSignal_RI;
2116 		info->input_signal_events.ri_down++;
2117 	}
2118 	DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2119 	if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2120 		slgt_irq_off(info, IRQ_RI);
2121 		return;
2122 	}
2123 	info->icount.rng++;
2124 	wake_up_interruptible(&info->status_event_wait_q);
2125 	wake_up_interruptible(&info->event_wait_q);
2126 	info->pending_bh |= BH_STATUS;
2127 }
2128 
isr_rxdata(struct slgt_info * info)2129 static void isr_rxdata(struct slgt_info *info)
2130 {
2131 	unsigned int count = info->rbuf_fill_count;
2132 	unsigned int i = info->rbuf_fill_index;
2133 	unsigned short reg;
2134 
2135 	while (rd_reg16(info, SSR) & IRQ_RXDATA) {
2136 		reg = rd_reg16(info, RDR);
2137 		DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
2138 		if (desc_complete(info->rbufs[i])) {
2139 			/* all buffers full */
2140 			rx_stop(info);
2141 			info->rx_restart = 1;
2142 			continue;
2143 		}
2144 		info->rbufs[i].buf[count++] = (unsigned char)reg;
2145 		/* async mode saves status byte to buffer for each data byte */
2146 		if (info->params.mode == MGSL_MODE_ASYNC)
2147 			info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
2148 		if (count == info->rbuf_fill_level || (reg & BIT10)) {
2149 			/* buffer full or end of frame */
2150 			set_desc_count(info->rbufs[i], count);
2151 			set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
2152 			info->rbuf_fill_count = count = 0;
2153 			if (++i == info->rbuf_count)
2154 				i = 0;
2155 			info->pending_bh |= BH_RECEIVE;
2156 		}
2157 	}
2158 
2159 	info->rbuf_fill_index = i;
2160 	info->rbuf_fill_count = count;
2161 }
2162 
isr_serial(struct slgt_info * info)2163 static void isr_serial(struct slgt_info *info)
2164 {
2165 	unsigned short status = rd_reg16(info, SSR);
2166 
2167 	DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2168 
2169 	wr_reg16(info, SSR, status); /* clear pending */
2170 
2171 	info->irq_occurred = true;
2172 
2173 	if (info->params.mode == MGSL_MODE_ASYNC) {
2174 		if (status & IRQ_TXIDLE) {
2175 			if (info->tx_active)
2176 				isr_txeom(info, status);
2177 		}
2178 		if (info->rx_pio && (status & IRQ_RXDATA))
2179 			isr_rxdata(info);
2180 		if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2181 			info->icount.brk++;
2182 			/* process break detection if tty control allows */
2183 			if (info->port.tty) {
2184 				if (!(status & info->ignore_status_mask)) {
2185 					if (info->read_status_mask & MASK_BREAK) {
2186 						tty_insert_flip_char(info->port.tty, 0, TTY_BREAK);
2187 						if (info->port.flags & ASYNC_SAK)
2188 							do_SAK(info->port.tty);
2189 					}
2190 				}
2191 			}
2192 		}
2193 	} else {
2194 		if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2195 			isr_txeom(info, status);
2196 		if (info->rx_pio && (status & IRQ_RXDATA))
2197 			isr_rxdata(info);
2198 		if (status & IRQ_RXIDLE) {
2199 			if (status & RXIDLE)
2200 				info->icount.rxidle++;
2201 			else
2202 				info->icount.exithunt++;
2203 			wake_up_interruptible(&info->event_wait_q);
2204 		}
2205 
2206 		if (status & IRQ_RXOVER)
2207 			rx_start(info);
2208 	}
2209 
2210 	if (status & IRQ_DSR)
2211 		dsr_change(info, status);
2212 	if (status & IRQ_CTS)
2213 		cts_change(info, status);
2214 	if (status & IRQ_DCD)
2215 		dcd_change(info, status);
2216 	if (status & IRQ_RI)
2217 		ri_change(info, status);
2218 }
2219 
isr_rdma(struct slgt_info * info)2220 static void isr_rdma(struct slgt_info *info)
2221 {
2222 	unsigned int status = rd_reg32(info, RDCSR);
2223 
2224 	DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2225 
2226 	/* RDCSR (rx DMA control/status)
2227 	 *
2228 	 * 31..07  reserved
2229 	 * 06      save status byte to DMA buffer
2230 	 * 05      error
2231 	 * 04      eol (end of list)
2232 	 * 03      eob (end of buffer)
2233 	 * 02      IRQ enable
2234 	 * 01      reset
2235 	 * 00      enable
2236 	 */
2237 	wr_reg32(info, RDCSR, status);	/* clear pending */
2238 
2239 	if (status & (BIT5 + BIT4)) {
2240 		DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2241 		info->rx_restart = true;
2242 	}
2243 	info->pending_bh |= BH_RECEIVE;
2244 }
2245 
isr_tdma(struct slgt_info * info)2246 static void isr_tdma(struct slgt_info *info)
2247 {
2248 	unsigned int status = rd_reg32(info, TDCSR);
2249 
2250 	DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2251 
2252 	/* TDCSR (tx DMA control/status)
2253 	 *
2254 	 * 31..06  reserved
2255 	 * 05      error
2256 	 * 04      eol (end of list)
2257 	 * 03      eob (end of buffer)
2258 	 * 02      IRQ enable
2259 	 * 01      reset
2260 	 * 00      enable
2261 	 */
2262 	wr_reg32(info, TDCSR, status);	/* clear pending */
2263 
2264 	if (status & (BIT5 + BIT4 + BIT3)) {
2265 		// another transmit buffer has completed
2266 		// run bottom half to get more send data from user
2267 		info->pending_bh |= BH_TRANSMIT;
2268 	}
2269 }
2270 
2271 /*
2272  * return true if there are unsent tx DMA buffers, otherwise false
2273  *
2274  * if there are unsent buffers then info->tbuf_start
2275  * is set to index of first unsent buffer
2276  */
unsent_tbufs(struct slgt_info * info)2277 static bool unsent_tbufs(struct slgt_info *info)
2278 {
2279 	unsigned int i = info->tbuf_current;
2280 	bool rc = false;
2281 
2282 	/*
2283 	 * search backwards from last loaded buffer (precedes tbuf_current)
2284 	 * for first unsent buffer (desc_count > 0)
2285 	 */
2286 
2287 	do {
2288 		if (i)
2289 			i--;
2290 		else
2291 			i = info->tbuf_count - 1;
2292 		if (!desc_count(info->tbufs[i]))
2293 			break;
2294 		info->tbuf_start = i;
2295 		rc = true;
2296 	} while (i != info->tbuf_current);
2297 
2298 	return rc;
2299 }
2300 
isr_txeom(struct slgt_info * info,unsigned short status)2301 static void isr_txeom(struct slgt_info *info, unsigned short status)
2302 {
2303 	DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2304 
2305 	slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2306 	tdma_reset(info);
2307 	if (status & IRQ_TXUNDER) {
2308 		unsigned short val = rd_reg16(info, TCR);
2309 		wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2310 		wr_reg16(info, TCR, val); /* clear reset bit */
2311 	}
2312 
2313 	if (info->tx_active) {
2314 		if (info->params.mode != MGSL_MODE_ASYNC) {
2315 			if (status & IRQ_TXUNDER)
2316 				info->icount.txunder++;
2317 			else if (status & IRQ_TXIDLE)
2318 				info->icount.txok++;
2319 		}
2320 
2321 		if (unsent_tbufs(info)) {
2322 			tx_start(info);
2323 			update_tx_timer(info);
2324 			return;
2325 		}
2326 		info->tx_active = false;
2327 
2328 		del_timer(&info->tx_timer);
2329 
2330 		if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2331 			info->signals &= ~SerialSignal_RTS;
2332 			info->drop_rts_on_tx_done = false;
2333 			set_signals(info);
2334 		}
2335 
2336 #if SYNCLINK_GENERIC_HDLC
2337 		if (info->netcount)
2338 			hdlcdev_tx_done(info);
2339 		else
2340 #endif
2341 		{
2342 			if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2343 				tx_stop(info);
2344 				return;
2345 			}
2346 			info->pending_bh |= BH_TRANSMIT;
2347 		}
2348 	}
2349 }
2350 
isr_gpio(struct slgt_info * info,unsigned int changed,unsigned int state)2351 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2352 {
2353 	struct cond_wait *w, *prev;
2354 
2355 	/* wake processes waiting for specific transitions */
2356 	for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2357 		if (w->data & changed) {
2358 			w->data = state;
2359 			wake_up_interruptible(&w->q);
2360 			if (prev != NULL)
2361 				prev->next = w->next;
2362 			else
2363 				info->gpio_wait_q = w->next;
2364 		} else
2365 			prev = w;
2366 	}
2367 }
2368 
2369 /* interrupt service routine
2370  *
2371  * 	irq	interrupt number
2372  * 	dev_id	device ID supplied during interrupt registration
2373  */
slgt_interrupt(int dummy,void * dev_id)2374 static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2375 {
2376 	struct slgt_info *info = dev_id;
2377 	unsigned int gsr;
2378 	unsigned int i;
2379 
2380 	DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2381 
2382 	while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2383 		DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2384 		info->irq_occurred = true;
2385 		for(i=0; i < info->port_count ; i++) {
2386 			if (info->port_array[i] == NULL)
2387 				continue;
2388 			spin_lock(&info->port_array[i]->lock);
2389 			if (gsr & (BIT8 << i))
2390 				isr_serial(info->port_array[i]);
2391 			if (gsr & (BIT16 << (i*2)))
2392 				isr_rdma(info->port_array[i]);
2393 			if (gsr & (BIT17 << (i*2)))
2394 				isr_tdma(info->port_array[i]);
2395 			spin_unlock(&info->port_array[i]->lock);
2396 		}
2397 	}
2398 
2399 	if (info->gpio_present) {
2400 		unsigned int state;
2401 		unsigned int changed;
2402 		spin_lock(&info->lock);
2403 		while ((changed = rd_reg32(info, IOSR)) != 0) {
2404 			DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2405 			/* read latched state of GPIO signals */
2406 			state = rd_reg32(info, IOVR);
2407 			/* clear pending GPIO interrupt bits */
2408 			wr_reg32(info, IOSR, changed);
2409 			for (i=0 ; i < info->port_count ; i++) {
2410 				if (info->port_array[i] != NULL)
2411 					isr_gpio(info->port_array[i], changed, state);
2412 			}
2413 		}
2414 		spin_unlock(&info->lock);
2415 	}
2416 
2417 	for(i=0; i < info->port_count ; i++) {
2418 		struct slgt_info *port = info->port_array[i];
2419 		if (port == NULL)
2420 			continue;
2421 		spin_lock(&port->lock);
2422 		if ((port->port.count || port->netcount) &&
2423 		    port->pending_bh && !port->bh_running &&
2424 		    !port->bh_requested) {
2425 			DBGISR(("%s bh queued\n", port->device_name));
2426 			schedule_work(&port->task);
2427 			port->bh_requested = true;
2428 		}
2429 		spin_unlock(&port->lock);
2430 	}
2431 
2432 	DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2433 	return IRQ_HANDLED;
2434 }
2435 
startup(struct slgt_info * info)2436 static int startup(struct slgt_info *info)
2437 {
2438 	DBGINFO(("%s startup\n", info->device_name));
2439 
2440 	if (info->port.flags & ASYNC_INITIALIZED)
2441 		return 0;
2442 
2443 	if (!info->tx_buf) {
2444 		info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2445 		if (!info->tx_buf) {
2446 			DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2447 			return -ENOMEM;
2448 		}
2449 	}
2450 
2451 	info->pending_bh = 0;
2452 
2453 	memset(&info->icount, 0, sizeof(info->icount));
2454 
2455 	/* program hardware for current parameters */
2456 	change_params(info);
2457 
2458 	if (info->port.tty)
2459 		clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2460 
2461 	info->port.flags |= ASYNC_INITIALIZED;
2462 
2463 	return 0;
2464 }
2465 
2466 /*
2467  *  called by close() and hangup() to shutdown hardware
2468  */
shutdown(struct slgt_info * info)2469 static void shutdown(struct slgt_info *info)
2470 {
2471 	unsigned long flags;
2472 
2473 	if (!(info->port.flags & ASYNC_INITIALIZED))
2474 		return;
2475 
2476 	DBGINFO(("%s shutdown\n", info->device_name));
2477 
2478 	/* clear status wait queue because status changes */
2479 	/* can't happen after shutting down the hardware */
2480 	wake_up_interruptible(&info->status_event_wait_q);
2481 	wake_up_interruptible(&info->event_wait_q);
2482 
2483 	del_timer_sync(&info->tx_timer);
2484 	del_timer_sync(&info->rx_timer);
2485 
2486 	kfree(info->tx_buf);
2487 	info->tx_buf = NULL;
2488 
2489 	spin_lock_irqsave(&info->lock,flags);
2490 
2491 	tx_stop(info);
2492 	rx_stop(info);
2493 
2494 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2495 
2496  	if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
2497  		info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
2498 		set_signals(info);
2499 	}
2500 
2501 	flush_cond_wait(&info->gpio_wait_q);
2502 
2503 	spin_unlock_irqrestore(&info->lock,flags);
2504 
2505 	if (info->port.tty)
2506 		set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2507 
2508 	info->port.flags &= ~ASYNC_INITIALIZED;
2509 }
2510 
program_hw(struct slgt_info * info)2511 static void program_hw(struct slgt_info *info)
2512 {
2513 	unsigned long flags;
2514 
2515 	spin_lock_irqsave(&info->lock,flags);
2516 
2517 	rx_stop(info);
2518 	tx_stop(info);
2519 
2520 	if (info->params.mode != MGSL_MODE_ASYNC ||
2521 	    info->netcount)
2522 		sync_mode(info);
2523 	else
2524 		async_mode(info);
2525 
2526 	set_signals(info);
2527 
2528 	info->dcd_chkcount = 0;
2529 	info->cts_chkcount = 0;
2530 	info->ri_chkcount = 0;
2531 	info->dsr_chkcount = 0;
2532 
2533 	slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
2534 	get_signals(info);
2535 
2536 	if (info->netcount ||
2537 	    (info->port.tty && info->port.tty->termios->c_cflag & CREAD))
2538 		rx_start(info);
2539 
2540 	spin_unlock_irqrestore(&info->lock,flags);
2541 }
2542 
2543 /*
2544  * reconfigure adapter based on new parameters
2545  */
change_params(struct slgt_info * info)2546 static void change_params(struct slgt_info *info)
2547 {
2548 	unsigned cflag;
2549 	int bits_per_char;
2550 
2551 	if (!info->port.tty || !info->port.tty->termios)
2552 		return;
2553 	DBGINFO(("%s change_params\n", info->device_name));
2554 
2555 	cflag = info->port.tty->termios->c_cflag;
2556 
2557 	/* if B0 rate (hangup) specified then negate DTR and RTS */
2558 	/* otherwise assert DTR and RTS */
2559  	if (cflag & CBAUD)
2560 		info->signals |= SerialSignal_RTS + SerialSignal_DTR;
2561 	else
2562 		info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
2563 
2564 	/* byte size and parity */
2565 
2566 	switch (cflag & CSIZE) {
2567 	case CS5: info->params.data_bits = 5; break;
2568 	case CS6: info->params.data_bits = 6; break;
2569 	case CS7: info->params.data_bits = 7; break;
2570 	case CS8: info->params.data_bits = 8; break;
2571 	default:  info->params.data_bits = 7; break;
2572 	}
2573 
2574 	info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2575 
2576 	if (cflag & PARENB)
2577 		info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2578 	else
2579 		info->params.parity = ASYNC_PARITY_NONE;
2580 
2581 	/* calculate number of jiffies to transmit a full
2582 	 * FIFO (32 bytes) at specified data rate
2583 	 */
2584 	bits_per_char = info->params.data_bits +
2585 			info->params.stop_bits + 1;
2586 
2587 	info->params.data_rate = tty_get_baud_rate(info->port.tty);
2588 
2589 	if (info->params.data_rate) {
2590 		info->timeout = (32*HZ*bits_per_char) /
2591 				info->params.data_rate;
2592 	}
2593 	info->timeout += HZ/50;		/* Add .02 seconds of slop */
2594 
2595 	if (cflag & CRTSCTS)
2596 		info->port.flags |= ASYNC_CTS_FLOW;
2597 	else
2598 		info->port.flags &= ~ASYNC_CTS_FLOW;
2599 
2600 	if (cflag & CLOCAL)
2601 		info->port.flags &= ~ASYNC_CHECK_CD;
2602 	else
2603 		info->port.flags |= ASYNC_CHECK_CD;
2604 
2605 	/* process tty input control flags */
2606 
2607 	info->read_status_mask = IRQ_RXOVER;
2608 	if (I_INPCK(info->port.tty))
2609 		info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2610  	if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2611  		info->read_status_mask |= MASK_BREAK;
2612 	if (I_IGNPAR(info->port.tty))
2613 		info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2614 	if (I_IGNBRK(info->port.tty)) {
2615 		info->ignore_status_mask |= MASK_BREAK;
2616 		/* If ignoring parity and break indicators, ignore
2617 		 * overruns too.  (For real raw support).
2618 		 */
2619 		if (I_IGNPAR(info->port.tty))
2620 			info->ignore_status_mask |= MASK_OVERRUN;
2621 	}
2622 
2623 	program_hw(info);
2624 }
2625 
get_stats(struct slgt_info * info,struct mgsl_icount __user * user_icount)2626 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2627 {
2628 	DBGINFO(("%s get_stats\n",  info->device_name));
2629 	if (!user_icount) {
2630 		memset(&info->icount, 0, sizeof(info->icount));
2631 	} else {
2632 		if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2633 			return -EFAULT;
2634 	}
2635 	return 0;
2636 }
2637 
get_params(struct slgt_info * info,MGSL_PARAMS __user * user_params)2638 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2639 {
2640 	DBGINFO(("%s get_params\n", info->device_name));
2641 	if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2642 		return -EFAULT;
2643 	return 0;
2644 }
2645 
set_params(struct slgt_info * info,MGSL_PARAMS __user * new_params)2646 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2647 {
2648  	unsigned long flags;
2649 	MGSL_PARAMS tmp_params;
2650 
2651 	DBGINFO(("%s set_params\n", info->device_name));
2652 	if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2653 		return -EFAULT;
2654 
2655 	spin_lock_irqsave(&info->lock, flags);
2656 	if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
2657 		info->base_clock = tmp_params.clock_speed;
2658 	else
2659 		memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2660 	spin_unlock_irqrestore(&info->lock, flags);
2661 
2662 	program_hw(info);
2663 
2664 	return 0;
2665 }
2666 
get_txidle(struct slgt_info * info,int __user * idle_mode)2667 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2668 {
2669 	DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2670 	if (put_user(info->idle_mode, idle_mode))
2671 		return -EFAULT;
2672 	return 0;
2673 }
2674 
set_txidle(struct slgt_info * info,int idle_mode)2675 static int set_txidle(struct slgt_info *info, int idle_mode)
2676 {
2677  	unsigned long flags;
2678 	DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2679 	spin_lock_irqsave(&info->lock,flags);
2680 	info->idle_mode = idle_mode;
2681 	if (info->params.mode != MGSL_MODE_ASYNC)
2682 		tx_set_idle(info);
2683 	spin_unlock_irqrestore(&info->lock,flags);
2684 	return 0;
2685 }
2686 
tx_enable(struct slgt_info * info,int enable)2687 static int tx_enable(struct slgt_info *info, int enable)
2688 {
2689  	unsigned long flags;
2690 	DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2691 	spin_lock_irqsave(&info->lock,flags);
2692 	if (enable) {
2693 		if (!info->tx_enabled)
2694 			tx_start(info);
2695 	} else {
2696 		if (info->tx_enabled)
2697 			tx_stop(info);
2698 	}
2699 	spin_unlock_irqrestore(&info->lock,flags);
2700 	return 0;
2701 }
2702 
2703 /*
2704  * abort transmit HDLC frame
2705  */
tx_abort(struct slgt_info * info)2706 static int tx_abort(struct slgt_info *info)
2707 {
2708  	unsigned long flags;
2709 	DBGINFO(("%s tx_abort\n", info->device_name));
2710 	spin_lock_irqsave(&info->lock,flags);
2711 	tdma_reset(info);
2712 	spin_unlock_irqrestore(&info->lock,flags);
2713 	return 0;
2714 }
2715 
rx_enable(struct slgt_info * info,int enable)2716 static int rx_enable(struct slgt_info *info, int enable)
2717 {
2718  	unsigned long flags;
2719 	unsigned int rbuf_fill_level;
2720 	DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2721 	spin_lock_irqsave(&info->lock,flags);
2722 	/*
2723 	 * enable[31..16] = receive DMA buffer fill level
2724 	 * 0 = noop (leave fill level unchanged)
2725 	 * fill level must be multiple of 4 and <= buffer size
2726 	 */
2727 	rbuf_fill_level = ((unsigned int)enable) >> 16;
2728 	if (rbuf_fill_level) {
2729 		if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2730 			spin_unlock_irqrestore(&info->lock, flags);
2731 			return -EINVAL;
2732 		}
2733 		info->rbuf_fill_level = rbuf_fill_level;
2734 		if (rbuf_fill_level < 128)
2735 			info->rx_pio = 1; /* PIO mode */
2736 		else
2737 			info->rx_pio = 0; /* DMA mode */
2738 		rx_stop(info); /* restart receiver to use new fill level */
2739 	}
2740 
2741 	/*
2742 	 * enable[1..0] = receiver enable command
2743 	 * 0 = disable
2744 	 * 1 = enable
2745 	 * 2 = enable or force hunt mode if already enabled
2746 	 */
2747 	enable &= 3;
2748 	if (enable) {
2749 		if (!info->rx_enabled)
2750 			rx_start(info);
2751 		else if (enable == 2) {
2752 			/* force hunt mode (write 1 to RCR[3]) */
2753 			wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2754 		}
2755 	} else {
2756 		if (info->rx_enabled)
2757 			rx_stop(info);
2758 	}
2759 	spin_unlock_irqrestore(&info->lock,flags);
2760 	return 0;
2761 }
2762 
2763 /*
2764  *  wait for specified event to occur
2765  */
wait_mgsl_event(struct slgt_info * info,int __user * mask_ptr)2766 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2767 {
2768  	unsigned long flags;
2769 	int s;
2770 	int rc=0;
2771 	struct mgsl_icount cprev, cnow;
2772 	int events;
2773 	int mask;
2774 	struct	_input_signal_events oldsigs, newsigs;
2775 	DECLARE_WAITQUEUE(wait, current);
2776 
2777 	if (get_user(mask, mask_ptr))
2778 		return -EFAULT;
2779 
2780 	DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2781 
2782 	spin_lock_irqsave(&info->lock,flags);
2783 
2784 	/* return immediately if state matches requested events */
2785 	get_signals(info);
2786 	s = info->signals;
2787 
2788 	events = mask &
2789 		( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2790  		  ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2791 		  ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2792 		  ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2793 	if (events) {
2794 		spin_unlock_irqrestore(&info->lock,flags);
2795 		goto exit;
2796 	}
2797 
2798 	/* save current irq counts */
2799 	cprev = info->icount;
2800 	oldsigs = info->input_signal_events;
2801 
2802 	/* enable hunt and idle irqs if needed */
2803 	if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2804 		unsigned short val = rd_reg16(info, SCR);
2805 		if (!(val & IRQ_RXIDLE))
2806 			wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2807 	}
2808 
2809 	set_current_state(TASK_INTERRUPTIBLE);
2810 	add_wait_queue(&info->event_wait_q, &wait);
2811 
2812 	spin_unlock_irqrestore(&info->lock,flags);
2813 
2814 	for(;;) {
2815 		schedule();
2816 		if (signal_pending(current)) {
2817 			rc = -ERESTARTSYS;
2818 			break;
2819 		}
2820 
2821 		/* get current irq counts */
2822 		spin_lock_irqsave(&info->lock,flags);
2823 		cnow = info->icount;
2824 		newsigs = info->input_signal_events;
2825 		set_current_state(TASK_INTERRUPTIBLE);
2826 		spin_unlock_irqrestore(&info->lock,flags);
2827 
2828 		/* if no change, wait aborted for some reason */
2829 		if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2830 		    newsigs.dsr_down == oldsigs.dsr_down &&
2831 		    newsigs.dcd_up   == oldsigs.dcd_up   &&
2832 		    newsigs.dcd_down == oldsigs.dcd_down &&
2833 		    newsigs.cts_up   == oldsigs.cts_up   &&
2834 		    newsigs.cts_down == oldsigs.cts_down &&
2835 		    newsigs.ri_up    == oldsigs.ri_up    &&
2836 		    newsigs.ri_down  == oldsigs.ri_down  &&
2837 		    cnow.exithunt    == cprev.exithunt   &&
2838 		    cnow.rxidle      == cprev.rxidle) {
2839 			rc = -EIO;
2840 			break;
2841 		}
2842 
2843 		events = mask &
2844 			( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2845 			  (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2846 			  (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2847 			  (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2848 			  (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2849 			  (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2850 			  (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2851 			  (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2852 			  (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2853 			  (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2854 		if (events)
2855 			break;
2856 
2857 		cprev = cnow;
2858 		oldsigs = newsigs;
2859 	}
2860 
2861 	remove_wait_queue(&info->event_wait_q, &wait);
2862 	set_current_state(TASK_RUNNING);
2863 
2864 
2865 	if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2866 		spin_lock_irqsave(&info->lock,flags);
2867 		if (!waitqueue_active(&info->event_wait_q)) {
2868 			/* disable enable exit hunt mode/idle rcvd IRQs */
2869 			wr_reg16(info, SCR,
2870 				(unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2871 		}
2872 		spin_unlock_irqrestore(&info->lock,flags);
2873 	}
2874 exit:
2875 	if (rc == 0)
2876 		rc = put_user(events, mask_ptr);
2877 	return rc;
2878 }
2879 
get_interface(struct slgt_info * info,int __user * if_mode)2880 static int get_interface(struct slgt_info *info, int __user *if_mode)
2881 {
2882 	DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2883 	if (put_user(info->if_mode, if_mode))
2884 		return -EFAULT;
2885 	return 0;
2886 }
2887 
set_interface(struct slgt_info * info,int if_mode)2888 static int set_interface(struct slgt_info *info, int if_mode)
2889 {
2890  	unsigned long flags;
2891 	unsigned short val;
2892 
2893 	DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2894 	spin_lock_irqsave(&info->lock,flags);
2895 	info->if_mode = if_mode;
2896 
2897 	msc_set_vcr(info);
2898 
2899 	/* TCR (tx control) 07  1=RTS driver control */
2900 	val = rd_reg16(info, TCR);
2901 	if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2902 		val |= BIT7;
2903 	else
2904 		val &= ~BIT7;
2905 	wr_reg16(info, TCR, val);
2906 
2907 	spin_unlock_irqrestore(&info->lock,flags);
2908 	return 0;
2909 }
2910 
get_xsync(struct slgt_info * info,int __user * xsync)2911 static int get_xsync(struct slgt_info *info, int __user *xsync)
2912 {
2913 	DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync));
2914 	if (put_user(info->xsync, xsync))
2915 		return -EFAULT;
2916 	return 0;
2917 }
2918 
2919 /*
2920  * set extended sync pattern (1 to 4 bytes) for extended sync mode
2921  *
2922  * sync pattern is contained in least significant bytes of value
2923  * most significant byte of sync pattern is oldest (1st sent/detected)
2924  */
set_xsync(struct slgt_info * info,int xsync)2925 static int set_xsync(struct slgt_info *info, int xsync)
2926 {
2927 	unsigned long flags;
2928 
2929 	DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync));
2930 	spin_lock_irqsave(&info->lock, flags);
2931 	info->xsync = xsync;
2932 	wr_reg32(info, XSR, xsync);
2933 	spin_unlock_irqrestore(&info->lock, flags);
2934 	return 0;
2935 }
2936 
get_xctrl(struct slgt_info * info,int __user * xctrl)2937 static int get_xctrl(struct slgt_info *info, int __user *xctrl)
2938 {
2939 	DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl));
2940 	if (put_user(info->xctrl, xctrl))
2941 		return -EFAULT;
2942 	return 0;
2943 }
2944 
2945 /*
2946  * set extended control options
2947  *
2948  * xctrl[31:19] reserved, must be zero
2949  * xctrl[18:17] extended sync pattern length in bytes
2950  *              00 = 1 byte  in xsr[7:0]
2951  *              01 = 2 bytes in xsr[15:0]
2952  *              10 = 3 bytes in xsr[23:0]
2953  *              11 = 4 bytes in xsr[31:0]
2954  * xctrl[16]    1 = enable terminal count, 0=disabled
2955  * xctrl[15:0]  receive terminal count for fixed length packets
2956  *              value is count minus one (0 = 1 byte packet)
2957  *              when terminal count is reached, receiver
2958  *              automatically returns to hunt mode and receive
2959  *              FIFO contents are flushed to DMA buffers with
2960  *              end of frame (EOF) status
2961  */
set_xctrl(struct slgt_info * info,int xctrl)2962 static int set_xctrl(struct slgt_info *info, int xctrl)
2963 {
2964 	unsigned long flags;
2965 
2966 	DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl));
2967 	spin_lock_irqsave(&info->lock, flags);
2968 	info->xctrl = xctrl;
2969 	wr_reg32(info, XCR, xctrl);
2970 	spin_unlock_irqrestore(&info->lock, flags);
2971 	return 0;
2972 }
2973 
2974 /*
2975  * set general purpose IO pin state and direction
2976  *
2977  * user_gpio fields:
2978  * state   each bit indicates a pin state
2979  * smask   set bit indicates pin state to set
2980  * dir     each bit indicates a pin direction (0=input, 1=output)
2981  * dmask   set bit indicates pin direction to set
2982  */
set_gpio(struct slgt_info * info,struct gpio_desc __user * user_gpio)2983 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2984 {
2985  	unsigned long flags;
2986 	struct gpio_desc gpio;
2987 	__u32 data;
2988 
2989 	if (!info->gpio_present)
2990 		return -EINVAL;
2991 	if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2992 		return -EFAULT;
2993 	DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2994 		 info->device_name, gpio.state, gpio.smask,
2995 		 gpio.dir, gpio.dmask));
2996 
2997 	spin_lock_irqsave(&info->port_array[0]->lock, flags);
2998 	if (gpio.dmask) {
2999 		data = rd_reg32(info, IODR);
3000 		data |= gpio.dmask & gpio.dir;
3001 		data &= ~(gpio.dmask & ~gpio.dir);
3002 		wr_reg32(info, IODR, data);
3003 	}
3004 	if (gpio.smask) {
3005 		data = rd_reg32(info, IOVR);
3006 		data |= gpio.smask & gpio.state;
3007 		data &= ~(gpio.smask & ~gpio.state);
3008 		wr_reg32(info, IOVR, data);
3009 	}
3010 	spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3011 
3012 	return 0;
3013 }
3014 
3015 /*
3016  * get general purpose IO pin state and direction
3017  */
get_gpio(struct slgt_info * info,struct gpio_desc __user * user_gpio)3018 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3019 {
3020 	struct gpio_desc gpio;
3021 	if (!info->gpio_present)
3022 		return -EINVAL;
3023 	gpio.state = rd_reg32(info, IOVR);
3024 	gpio.smask = 0xffffffff;
3025 	gpio.dir   = rd_reg32(info, IODR);
3026 	gpio.dmask = 0xffffffff;
3027 	if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3028 		return -EFAULT;
3029 	DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
3030 		 info->device_name, gpio.state, gpio.dir));
3031 	return 0;
3032 }
3033 
3034 /*
3035  * conditional wait facility
3036  */
init_cond_wait(struct cond_wait * w,unsigned int data)3037 static void init_cond_wait(struct cond_wait *w, unsigned int data)
3038 {
3039 	init_waitqueue_head(&w->q);
3040 	init_waitqueue_entry(&w->wait, current);
3041 	w->data = data;
3042 }
3043 
add_cond_wait(struct cond_wait ** head,struct cond_wait * w)3044 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
3045 {
3046 	set_current_state(TASK_INTERRUPTIBLE);
3047 	add_wait_queue(&w->q, &w->wait);
3048 	w->next = *head;
3049 	*head = w;
3050 }
3051 
remove_cond_wait(struct cond_wait ** head,struct cond_wait * cw)3052 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
3053 {
3054 	struct cond_wait *w, *prev;
3055 	remove_wait_queue(&cw->q, &cw->wait);
3056 	set_current_state(TASK_RUNNING);
3057 	for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
3058 		if (w == cw) {
3059 			if (prev != NULL)
3060 				prev->next = w->next;
3061 			else
3062 				*head = w->next;
3063 			break;
3064 		}
3065 	}
3066 }
3067 
flush_cond_wait(struct cond_wait ** head)3068 static void flush_cond_wait(struct cond_wait **head)
3069 {
3070 	while (*head != NULL) {
3071 		wake_up_interruptible(&(*head)->q);
3072 		*head = (*head)->next;
3073 	}
3074 }
3075 
3076 /*
3077  * wait for general purpose I/O pin(s) to enter specified state
3078  *
3079  * user_gpio fields:
3080  * state - bit indicates target pin state
3081  * smask - set bit indicates watched pin
3082  *
3083  * The wait ends when at least one watched pin enters the specified
3084  * state. When 0 (no error) is returned, user_gpio->state is set to the
3085  * state of all GPIO pins when the wait ends.
3086  *
3087  * Note: Each pin may be a dedicated input, dedicated output, or
3088  * configurable input/output. The number and configuration of pins
3089  * varies with the specific adapter model. Only input pins (dedicated
3090  * or configured) can be monitored with this function.
3091  */
wait_gpio(struct slgt_info * info,struct gpio_desc __user * user_gpio)3092 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3093 {
3094  	unsigned long flags;
3095 	int rc = 0;
3096 	struct gpio_desc gpio;
3097 	struct cond_wait wait;
3098 	u32 state;
3099 
3100 	if (!info->gpio_present)
3101 		return -EINVAL;
3102 	if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
3103 		return -EFAULT;
3104 	DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
3105 		 info->device_name, gpio.state, gpio.smask));
3106 	/* ignore output pins identified by set IODR bit */
3107 	if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
3108 		return -EINVAL;
3109 	init_cond_wait(&wait, gpio.smask);
3110 
3111 	spin_lock_irqsave(&info->port_array[0]->lock, flags);
3112 	/* enable interrupts for watched pins */
3113 	wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3114 	/* get current pin states */
3115 	state = rd_reg32(info, IOVR);
3116 
3117 	if (gpio.smask & ~(state ^ gpio.state)) {
3118 		/* already in target state */
3119 		gpio.state = state;
3120 	} else {
3121 		/* wait for target state */
3122 		add_cond_wait(&info->gpio_wait_q, &wait);
3123 		spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3124 		schedule();
3125 		if (signal_pending(current))
3126 			rc = -ERESTARTSYS;
3127 		else
3128 			gpio.state = wait.data;
3129 		spin_lock_irqsave(&info->port_array[0]->lock, flags);
3130 		remove_cond_wait(&info->gpio_wait_q, &wait);
3131 	}
3132 
3133 	/* disable all GPIO interrupts if no waiting processes */
3134 	if (info->gpio_wait_q == NULL)
3135 		wr_reg32(info, IOER, 0);
3136 	spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3137 
3138 	if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3139 		rc = -EFAULT;
3140 	return rc;
3141 }
3142 
modem_input_wait(struct slgt_info * info,int arg)3143 static int modem_input_wait(struct slgt_info *info,int arg)
3144 {
3145  	unsigned long flags;
3146 	int rc;
3147 	struct mgsl_icount cprev, cnow;
3148 	DECLARE_WAITQUEUE(wait, current);
3149 
3150 	/* save current irq counts */
3151 	spin_lock_irqsave(&info->lock,flags);
3152 	cprev = info->icount;
3153 	add_wait_queue(&info->status_event_wait_q, &wait);
3154 	set_current_state(TASK_INTERRUPTIBLE);
3155 	spin_unlock_irqrestore(&info->lock,flags);
3156 
3157 	for(;;) {
3158 		schedule();
3159 		if (signal_pending(current)) {
3160 			rc = -ERESTARTSYS;
3161 			break;
3162 		}
3163 
3164 		/* get new irq counts */
3165 		spin_lock_irqsave(&info->lock,flags);
3166 		cnow = info->icount;
3167 		set_current_state(TASK_INTERRUPTIBLE);
3168 		spin_unlock_irqrestore(&info->lock,flags);
3169 
3170 		/* if no change, wait aborted for some reason */
3171 		if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3172 		    cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3173 			rc = -EIO;
3174 			break;
3175 		}
3176 
3177 		/* check for change in caller specified modem input */
3178 		if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3179 		    (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3180 		    (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
3181 		    (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3182 			rc = 0;
3183 			break;
3184 		}
3185 
3186 		cprev = cnow;
3187 	}
3188 	remove_wait_queue(&info->status_event_wait_q, &wait);
3189 	set_current_state(TASK_RUNNING);
3190 	return rc;
3191 }
3192 
3193 /*
3194  *  return state of serial control and status signals
3195  */
tiocmget(struct tty_struct * tty)3196 static int tiocmget(struct tty_struct *tty)
3197 {
3198 	struct slgt_info *info = tty->driver_data;
3199 	unsigned int result;
3200  	unsigned long flags;
3201 
3202 	spin_lock_irqsave(&info->lock,flags);
3203  	get_signals(info);
3204 	spin_unlock_irqrestore(&info->lock,flags);
3205 
3206 	result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3207 		((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3208 		((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3209 		((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
3210 		((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3211 		((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3212 
3213 	DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3214 	return result;
3215 }
3216 
3217 /*
3218  * set modem control signals (DTR/RTS)
3219  *
3220  * 	cmd	signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3221  *		TIOCMSET = set/clear signal values
3222  * 	value	bit mask for command
3223  */
tiocmset(struct tty_struct * tty,unsigned int set,unsigned int clear)3224 static int tiocmset(struct tty_struct *tty,
3225 		    unsigned int set, unsigned int clear)
3226 {
3227 	struct slgt_info *info = tty->driver_data;
3228  	unsigned long flags;
3229 
3230 	DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3231 
3232 	if (set & TIOCM_RTS)
3233 		info->signals |= SerialSignal_RTS;
3234 	if (set & TIOCM_DTR)
3235 		info->signals |= SerialSignal_DTR;
3236 	if (clear & TIOCM_RTS)
3237 		info->signals &= ~SerialSignal_RTS;
3238 	if (clear & TIOCM_DTR)
3239 		info->signals &= ~SerialSignal_DTR;
3240 
3241 	spin_lock_irqsave(&info->lock,flags);
3242  	set_signals(info);
3243 	spin_unlock_irqrestore(&info->lock,flags);
3244 	return 0;
3245 }
3246 
carrier_raised(struct tty_port * port)3247 static int carrier_raised(struct tty_port *port)
3248 {
3249 	unsigned long flags;
3250 	struct slgt_info *info = container_of(port, struct slgt_info, port);
3251 
3252 	spin_lock_irqsave(&info->lock,flags);
3253  	get_signals(info);
3254 	spin_unlock_irqrestore(&info->lock,flags);
3255 	return (info->signals & SerialSignal_DCD) ? 1 : 0;
3256 }
3257 
dtr_rts(struct tty_port * port,int on)3258 static void dtr_rts(struct tty_port *port, int on)
3259 {
3260 	unsigned long flags;
3261 	struct slgt_info *info = container_of(port, struct slgt_info, port);
3262 
3263 	spin_lock_irqsave(&info->lock,flags);
3264 	if (on)
3265 		info->signals |= SerialSignal_RTS + SerialSignal_DTR;
3266 	else
3267 		info->signals &= ~(SerialSignal_RTS + SerialSignal_DTR);
3268  	set_signals(info);
3269 	spin_unlock_irqrestore(&info->lock,flags);
3270 }
3271 
3272 
3273 /*
3274  *  block current process until the device is ready to open
3275  */
block_til_ready(struct tty_struct * tty,struct file * filp,struct slgt_info * info)3276 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3277 			   struct slgt_info *info)
3278 {
3279 	DECLARE_WAITQUEUE(wait, current);
3280 	int		retval;
3281 	bool		do_clocal = false;
3282 	bool		extra_count = false;
3283 	unsigned long	flags;
3284 	int		cd;
3285 	struct tty_port *port = &info->port;
3286 
3287 	DBGINFO(("%s block_til_ready\n", tty->driver->name));
3288 
3289 	if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
3290 		/* nonblock mode is set or port is not enabled */
3291 		port->flags |= ASYNC_NORMAL_ACTIVE;
3292 		return 0;
3293 	}
3294 
3295 	if (tty->termios->c_cflag & CLOCAL)
3296 		do_clocal = true;
3297 
3298 	/* Wait for carrier detect and the line to become
3299 	 * free (i.e., not in use by the callout).  While we are in
3300 	 * this loop, port->count is dropped by one, so that
3301 	 * close() knows when to free things.  We restore it upon
3302 	 * exit, either normal or abnormal.
3303 	 */
3304 
3305 	retval = 0;
3306 	add_wait_queue(&port->open_wait, &wait);
3307 
3308 	spin_lock_irqsave(&info->lock, flags);
3309 	if (!tty_hung_up_p(filp)) {
3310 		extra_count = true;
3311 		port->count--;
3312 	}
3313 	spin_unlock_irqrestore(&info->lock, flags);
3314 	port->blocked_open++;
3315 
3316 	while (1) {
3317 		if ((tty->termios->c_cflag & CBAUD))
3318 			tty_port_raise_dtr_rts(port);
3319 
3320 		set_current_state(TASK_INTERRUPTIBLE);
3321 
3322 		if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
3323 			retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3324 					-EAGAIN : -ERESTARTSYS;
3325 			break;
3326 		}
3327 
3328 		cd = tty_port_carrier_raised(port);
3329 
3330  		if (!(port->flags & ASYNC_CLOSING) && (do_clocal || cd ))
3331  			break;
3332 
3333 		if (signal_pending(current)) {
3334 			retval = -ERESTARTSYS;
3335 			break;
3336 		}
3337 
3338 		DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3339 		tty_unlock();
3340 		schedule();
3341 		tty_lock();
3342 	}
3343 
3344 	set_current_state(TASK_RUNNING);
3345 	remove_wait_queue(&port->open_wait, &wait);
3346 
3347 	if (extra_count)
3348 		port->count++;
3349 	port->blocked_open--;
3350 
3351 	if (!retval)
3352 		port->flags |= ASYNC_NORMAL_ACTIVE;
3353 
3354 	DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3355 	return retval;
3356 }
3357 
alloc_tmp_rbuf(struct slgt_info * info)3358 static int alloc_tmp_rbuf(struct slgt_info *info)
3359 {
3360 	info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3361 	if (info->tmp_rbuf == NULL)
3362 		return -ENOMEM;
3363 	return 0;
3364 }
3365 
free_tmp_rbuf(struct slgt_info * info)3366 static void free_tmp_rbuf(struct slgt_info *info)
3367 {
3368 	kfree(info->tmp_rbuf);
3369 	info->tmp_rbuf = NULL;
3370 }
3371 
3372 /*
3373  * allocate DMA descriptor lists.
3374  */
alloc_desc(struct slgt_info * info)3375 static int alloc_desc(struct slgt_info *info)
3376 {
3377 	unsigned int i;
3378 	unsigned int pbufs;
3379 
3380 	/* allocate memory to hold descriptor lists */
3381 	info->bufs = pci_alloc_consistent(info->pdev, DESC_LIST_SIZE, &info->bufs_dma_addr);
3382 	if (info->bufs == NULL)
3383 		return -ENOMEM;
3384 
3385 	memset(info->bufs, 0, DESC_LIST_SIZE);
3386 
3387 	info->rbufs = (struct slgt_desc*)info->bufs;
3388 	info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3389 
3390 	pbufs = (unsigned int)info->bufs_dma_addr;
3391 
3392 	/*
3393 	 * Build circular lists of descriptors
3394 	 */
3395 
3396 	for (i=0; i < info->rbuf_count; i++) {
3397 		/* physical address of this descriptor */
3398 		info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3399 
3400 		/* physical address of next descriptor */
3401 		if (i == info->rbuf_count - 1)
3402 			info->rbufs[i].next = cpu_to_le32(pbufs);
3403 		else
3404 			info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3405 		set_desc_count(info->rbufs[i], DMABUFSIZE);
3406 	}
3407 
3408 	for (i=0; i < info->tbuf_count; i++) {
3409 		/* physical address of this descriptor */
3410 		info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3411 
3412 		/* physical address of next descriptor */
3413 		if (i == info->tbuf_count - 1)
3414 			info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3415 		else
3416 			info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3417 	}
3418 
3419 	return 0;
3420 }
3421 
free_desc(struct slgt_info * info)3422 static void free_desc(struct slgt_info *info)
3423 {
3424 	if (info->bufs != NULL) {
3425 		pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3426 		info->bufs  = NULL;
3427 		info->rbufs = NULL;
3428 		info->tbufs = NULL;
3429 	}
3430 }
3431 
alloc_bufs(struct slgt_info * info,struct slgt_desc * bufs,int count)3432 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3433 {
3434 	int i;
3435 	for (i=0; i < count; i++) {
3436 		if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3437 			return -ENOMEM;
3438 		bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3439 	}
3440 	return 0;
3441 }
3442 
free_bufs(struct slgt_info * info,struct slgt_desc * bufs,int count)3443 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3444 {
3445 	int i;
3446 	for (i=0; i < count; i++) {
3447 		if (bufs[i].buf == NULL)
3448 			continue;
3449 		pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3450 		bufs[i].buf = NULL;
3451 	}
3452 }
3453 
alloc_dma_bufs(struct slgt_info * info)3454 static int alloc_dma_bufs(struct slgt_info *info)
3455 {
3456 	info->rbuf_count = 32;
3457 	info->tbuf_count = 32;
3458 
3459 	if (alloc_desc(info) < 0 ||
3460 	    alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3461 	    alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3462 	    alloc_tmp_rbuf(info) < 0) {
3463 		DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3464 		return -ENOMEM;
3465 	}
3466 	reset_rbufs(info);
3467 	return 0;
3468 }
3469 
free_dma_bufs(struct slgt_info * info)3470 static void free_dma_bufs(struct slgt_info *info)
3471 {
3472 	if (info->bufs) {
3473 		free_bufs(info, info->rbufs, info->rbuf_count);
3474 		free_bufs(info, info->tbufs, info->tbuf_count);
3475 		free_desc(info);
3476 	}
3477 	free_tmp_rbuf(info);
3478 }
3479 
claim_resources(struct slgt_info * info)3480 static int claim_resources(struct slgt_info *info)
3481 {
3482 	if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3483 		DBGERR(("%s reg addr conflict, addr=%08X\n",
3484 			info->device_name, info->phys_reg_addr));
3485 		info->init_error = DiagStatus_AddressConflict;
3486 		goto errout;
3487 	}
3488 	else
3489 		info->reg_addr_requested = true;
3490 
3491 	info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
3492 	if (!info->reg_addr) {
3493 		DBGERR(("%s can't map device registers, addr=%08X\n",
3494 			info->device_name, info->phys_reg_addr));
3495 		info->init_error = DiagStatus_CantAssignPciResources;
3496 		goto errout;
3497 	}
3498 	return 0;
3499 
3500 errout:
3501 	release_resources(info);
3502 	return -ENODEV;
3503 }
3504 
release_resources(struct slgt_info * info)3505 static void release_resources(struct slgt_info *info)
3506 {
3507 	if (info->irq_requested) {
3508 		free_irq(info->irq_level, info);
3509 		info->irq_requested = false;
3510 	}
3511 
3512 	if (info->reg_addr_requested) {
3513 		release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3514 		info->reg_addr_requested = false;
3515 	}
3516 
3517 	if (info->reg_addr) {
3518 		iounmap(info->reg_addr);
3519 		info->reg_addr = NULL;
3520 	}
3521 }
3522 
3523 /* Add the specified device instance data structure to the
3524  * global linked list of devices and increment the device count.
3525  */
add_device(struct slgt_info * info)3526 static void add_device(struct slgt_info *info)
3527 {
3528 	char *devstr;
3529 
3530 	info->next_device = NULL;
3531 	info->line = slgt_device_count;
3532 	sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3533 
3534 	if (info->line < MAX_DEVICES) {
3535 		if (maxframe[info->line])
3536 			info->max_frame_size = maxframe[info->line];
3537 	}
3538 
3539 	slgt_device_count++;
3540 
3541 	if (!slgt_device_list)
3542 		slgt_device_list = info;
3543 	else {
3544 		struct slgt_info *current_dev = slgt_device_list;
3545 		while(current_dev->next_device)
3546 			current_dev = current_dev->next_device;
3547 		current_dev->next_device = info;
3548 	}
3549 
3550 	if (info->max_frame_size < 4096)
3551 		info->max_frame_size = 4096;
3552 	else if (info->max_frame_size > 65535)
3553 		info->max_frame_size = 65535;
3554 
3555 	switch(info->pdev->device) {
3556 	case SYNCLINK_GT_DEVICE_ID:
3557 		devstr = "GT";
3558 		break;
3559 	case SYNCLINK_GT2_DEVICE_ID:
3560 		devstr = "GT2";
3561 		break;
3562 	case SYNCLINK_GT4_DEVICE_ID:
3563 		devstr = "GT4";
3564 		break;
3565 	case SYNCLINK_AC_DEVICE_ID:
3566 		devstr = "AC";
3567 		info->params.mode = MGSL_MODE_ASYNC;
3568 		break;
3569 	default:
3570 		devstr = "(unknown model)";
3571 	}
3572 	printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3573 		devstr, info->device_name, info->phys_reg_addr,
3574 		info->irq_level, info->max_frame_size);
3575 
3576 #if SYNCLINK_GENERIC_HDLC
3577 	hdlcdev_init(info);
3578 #endif
3579 }
3580 
3581 static const struct tty_port_operations slgt_port_ops = {
3582 	.carrier_raised = carrier_raised,
3583 	.dtr_rts = dtr_rts,
3584 };
3585 
3586 /*
3587  *  allocate device instance structure, return NULL on failure
3588  */
alloc_dev(int adapter_num,int port_num,struct pci_dev * pdev)3589 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3590 {
3591 	struct slgt_info *info;
3592 
3593 	info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3594 
3595 	if (!info) {
3596 		DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3597 			driver_name, adapter_num, port_num));
3598 	} else {
3599 		tty_port_init(&info->port);
3600 		info->port.ops = &slgt_port_ops;
3601 		info->magic = MGSL_MAGIC;
3602 		INIT_WORK(&info->task, bh_handler);
3603 		info->max_frame_size = 4096;
3604 		info->base_clock = 14745600;
3605 		info->rbuf_fill_level = DMABUFSIZE;
3606 		info->port.close_delay = 5*HZ/10;
3607 		info->port.closing_wait = 30*HZ;
3608 		init_waitqueue_head(&info->status_event_wait_q);
3609 		init_waitqueue_head(&info->event_wait_q);
3610 		spin_lock_init(&info->netlock);
3611 		memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3612 		info->idle_mode = HDLC_TXIDLE_FLAGS;
3613 		info->adapter_num = adapter_num;
3614 		info->port_num = port_num;
3615 
3616 		setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
3617 		setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
3618 
3619 		/* Copy configuration info to device instance data */
3620 		info->pdev = pdev;
3621 		info->irq_level = pdev->irq;
3622 		info->phys_reg_addr = pci_resource_start(pdev,0);
3623 
3624 		info->bus_type = MGSL_BUS_TYPE_PCI;
3625 		info->irq_flags = IRQF_SHARED;
3626 
3627 		info->init_error = -1; /* assume error, set to 0 on successful init */
3628 	}
3629 
3630 	return info;
3631 }
3632 
device_init(int adapter_num,struct pci_dev * pdev)3633 static void device_init(int adapter_num, struct pci_dev *pdev)
3634 {
3635 	struct slgt_info *port_array[SLGT_MAX_PORTS];
3636 	int i;
3637 	int port_count = 1;
3638 
3639 	if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3640 		port_count = 2;
3641 	else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3642 		port_count = 4;
3643 
3644 	/* allocate device instances for all ports */
3645 	for (i=0; i < port_count; ++i) {
3646 		port_array[i] = alloc_dev(adapter_num, i, pdev);
3647 		if (port_array[i] == NULL) {
3648 			for (--i; i >= 0; --i)
3649 				kfree(port_array[i]);
3650 			return;
3651 		}
3652 	}
3653 
3654 	/* give copy of port_array to all ports and add to device list  */
3655 	for (i=0; i < port_count; ++i) {
3656 		memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3657 		add_device(port_array[i]);
3658 		port_array[i]->port_count = port_count;
3659 		spin_lock_init(&port_array[i]->lock);
3660 	}
3661 
3662 	/* Allocate and claim adapter resources */
3663 	if (!claim_resources(port_array[0])) {
3664 
3665 		alloc_dma_bufs(port_array[0]);
3666 
3667 		/* copy resource information from first port to others */
3668 		for (i = 1; i < port_count; ++i) {
3669 			port_array[i]->irq_level = port_array[0]->irq_level;
3670 			port_array[i]->reg_addr  = port_array[0]->reg_addr;
3671 			alloc_dma_bufs(port_array[i]);
3672 		}
3673 
3674 		if (request_irq(port_array[0]->irq_level,
3675 					slgt_interrupt,
3676 					port_array[0]->irq_flags,
3677 					port_array[0]->device_name,
3678 					port_array[0]) < 0) {
3679 			DBGERR(("%s request_irq failed IRQ=%d\n",
3680 				port_array[0]->device_name,
3681 				port_array[0]->irq_level));
3682 		} else {
3683 			port_array[0]->irq_requested = true;
3684 			adapter_test(port_array[0]);
3685 			for (i=1 ; i < port_count ; i++) {
3686 				port_array[i]->init_error = port_array[0]->init_error;
3687 				port_array[i]->gpio_present = port_array[0]->gpio_present;
3688 			}
3689 		}
3690 	}
3691 
3692 	for (i=0; i < port_count; ++i)
3693 		tty_register_device(serial_driver, port_array[i]->line, &(port_array[i]->pdev->dev));
3694 }
3695 
init_one(struct pci_dev * dev,const struct pci_device_id * ent)3696 static int __devinit init_one(struct pci_dev *dev,
3697 			      const struct pci_device_id *ent)
3698 {
3699 	if (pci_enable_device(dev)) {
3700 		printk("error enabling pci device %p\n", dev);
3701 		return -EIO;
3702 	}
3703 	pci_set_master(dev);
3704 	device_init(slgt_device_count, dev);
3705 	return 0;
3706 }
3707 
remove_one(struct pci_dev * dev)3708 static void __devexit remove_one(struct pci_dev *dev)
3709 {
3710 }
3711 
3712 static const struct tty_operations ops = {
3713 	.open = open,
3714 	.close = close,
3715 	.write = write,
3716 	.put_char = put_char,
3717 	.flush_chars = flush_chars,
3718 	.write_room = write_room,
3719 	.chars_in_buffer = chars_in_buffer,
3720 	.flush_buffer = flush_buffer,
3721 	.ioctl = ioctl,
3722 	.compat_ioctl = slgt_compat_ioctl,
3723 	.throttle = throttle,
3724 	.unthrottle = unthrottle,
3725 	.send_xchar = send_xchar,
3726 	.break_ctl = set_break,
3727 	.wait_until_sent = wait_until_sent,
3728 	.set_termios = set_termios,
3729 	.stop = tx_hold,
3730 	.start = tx_release,
3731 	.hangup = hangup,
3732 	.tiocmget = tiocmget,
3733 	.tiocmset = tiocmset,
3734 	.get_icount = get_icount,
3735 	.proc_fops = &synclink_gt_proc_fops,
3736 };
3737 
slgt_cleanup(void)3738 static void slgt_cleanup(void)
3739 {
3740 	int rc;
3741 	struct slgt_info *info;
3742 	struct slgt_info *tmp;
3743 
3744 	printk(KERN_INFO "unload %s\n", driver_name);
3745 
3746 	if (serial_driver) {
3747 		for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3748 			tty_unregister_device(serial_driver, info->line);
3749 		if ((rc = tty_unregister_driver(serial_driver)))
3750 			DBGERR(("tty_unregister_driver error=%d\n", rc));
3751 		put_tty_driver(serial_driver);
3752 	}
3753 
3754 	/* reset devices */
3755 	info = slgt_device_list;
3756 	while(info) {
3757 		reset_port(info);
3758 		info = info->next_device;
3759 	}
3760 
3761 	/* release devices */
3762 	info = slgt_device_list;
3763 	while(info) {
3764 #if SYNCLINK_GENERIC_HDLC
3765 		hdlcdev_exit(info);
3766 #endif
3767 		free_dma_bufs(info);
3768 		free_tmp_rbuf(info);
3769 		if (info->port_num == 0)
3770 			release_resources(info);
3771 		tmp = info;
3772 		info = info->next_device;
3773 		kfree(tmp);
3774 	}
3775 
3776 	if (pci_registered)
3777 		pci_unregister_driver(&pci_driver);
3778 }
3779 
3780 /*
3781  *  Driver initialization entry point.
3782  */
slgt_init(void)3783 static int __init slgt_init(void)
3784 {
3785 	int rc;
3786 
3787 	printk(KERN_INFO "%s\n", driver_name);
3788 
3789 	serial_driver = alloc_tty_driver(MAX_DEVICES);
3790 	if (!serial_driver) {
3791 		printk("%s can't allocate tty driver\n", driver_name);
3792 		return -ENOMEM;
3793 	}
3794 
3795 	/* Initialize the tty_driver structure */
3796 
3797 	serial_driver->driver_name = tty_driver_name;
3798 	serial_driver->name = tty_dev_prefix;
3799 	serial_driver->major = ttymajor;
3800 	serial_driver->minor_start = 64;
3801 	serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3802 	serial_driver->subtype = SERIAL_TYPE_NORMAL;
3803 	serial_driver->init_termios = tty_std_termios;
3804 	serial_driver->init_termios.c_cflag =
3805 		B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3806 	serial_driver->init_termios.c_ispeed = 9600;
3807 	serial_driver->init_termios.c_ospeed = 9600;
3808 	serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3809 	tty_set_operations(serial_driver, &ops);
3810 	if ((rc = tty_register_driver(serial_driver)) < 0) {
3811 		DBGERR(("%s can't register serial driver\n", driver_name));
3812 		put_tty_driver(serial_driver);
3813 		serial_driver = NULL;
3814 		goto error;
3815 	}
3816 
3817 	printk(KERN_INFO "%s, tty major#%d\n",
3818 	       driver_name, serial_driver->major);
3819 
3820 	slgt_device_count = 0;
3821 	if ((rc = pci_register_driver(&pci_driver)) < 0) {
3822 		printk("%s pci_register_driver error=%d\n", driver_name, rc);
3823 		goto error;
3824 	}
3825 	pci_registered = true;
3826 
3827 	if (!slgt_device_list)
3828 		printk("%s no devices found\n",driver_name);
3829 
3830 	return 0;
3831 
3832 error:
3833 	slgt_cleanup();
3834 	return rc;
3835 }
3836 
slgt_exit(void)3837 static void __exit slgt_exit(void)
3838 {
3839 	slgt_cleanup();
3840 }
3841 
3842 module_init(slgt_init);
3843 module_exit(slgt_exit);
3844 
3845 /*
3846  * register access routines
3847  */
3848 
3849 #define CALC_REGADDR() \
3850 	unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3851 	if (addr >= 0x80) \
3852 		reg_addr += (info->port_num) * 32; \
3853 	else if (addr >= 0x40)	\
3854 		reg_addr += (info->port_num) * 16;
3855 
rd_reg8(struct slgt_info * info,unsigned int addr)3856 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3857 {
3858 	CALC_REGADDR();
3859 	return readb((void __iomem *)reg_addr);
3860 }
3861 
wr_reg8(struct slgt_info * info,unsigned int addr,__u8 value)3862 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3863 {
3864 	CALC_REGADDR();
3865 	writeb(value, (void __iomem *)reg_addr);
3866 }
3867 
rd_reg16(struct slgt_info * info,unsigned int addr)3868 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3869 {
3870 	CALC_REGADDR();
3871 	return readw((void __iomem *)reg_addr);
3872 }
3873 
wr_reg16(struct slgt_info * info,unsigned int addr,__u16 value)3874 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3875 {
3876 	CALC_REGADDR();
3877 	writew(value, (void __iomem *)reg_addr);
3878 }
3879 
rd_reg32(struct slgt_info * info,unsigned int addr)3880 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3881 {
3882 	CALC_REGADDR();
3883 	return readl((void __iomem *)reg_addr);
3884 }
3885 
wr_reg32(struct slgt_info * info,unsigned int addr,__u32 value)3886 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3887 {
3888 	CALC_REGADDR();
3889 	writel(value, (void __iomem *)reg_addr);
3890 }
3891 
rdma_reset(struct slgt_info * info)3892 static void rdma_reset(struct slgt_info *info)
3893 {
3894 	unsigned int i;
3895 
3896 	/* set reset bit */
3897 	wr_reg32(info, RDCSR, BIT1);
3898 
3899 	/* wait for enable bit cleared */
3900 	for(i=0 ; i < 1000 ; i++)
3901 		if (!(rd_reg32(info, RDCSR) & BIT0))
3902 			break;
3903 }
3904 
tdma_reset(struct slgt_info * info)3905 static void tdma_reset(struct slgt_info *info)
3906 {
3907 	unsigned int i;
3908 
3909 	/* set reset bit */
3910 	wr_reg32(info, TDCSR, BIT1);
3911 
3912 	/* wait for enable bit cleared */
3913 	for(i=0 ; i < 1000 ; i++)
3914 		if (!(rd_reg32(info, TDCSR) & BIT0))
3915 			break;
3916 }
3917 
3918 /*
3919  * enable internal loopback
3920  * TxCLK and RxCLK are generated from BRG
3921  * and TxD is looped back to RxD internally.
3922  */
enable_loopback(struct slgt_info * info)3923 static void enable_loopback(struct slgt_info *info)
3924 {
3925 	/* SCR (serial control) BIT2=loopback enable */
3926 	wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3927 
3928 	if (info->params.mode != MGSL_MODE_ASYNC) {
3929 		/* CCR (clock control)
3930 		 * 07..05  tx clock source (010 = BRG)
3931 		 * 04..02  rx clock source (010 = BRG)
3932 		 * 01      auxclk enable   (0 = disable)
3933 		 * 00      BRG enable      (1 = enable)
3934 		 *
3935 		 * 0100 1001
3936 		 */
3937 		wr_reg8(info, CCR, 0x49);
3938 
3939 		/* set speed if available, otherwise use default */
3940 		if (info->params.clock_speed)
3941 			set_rate(info, info->params.clock_speed);
3942 		else
3943 			set_rate(info, 3686400);
3944 	}
3945 }
3946 
3947 /*
3948  *  set baud rate generator to specified rate
3949  */
set_rate(struct slgt_info * info,u32 rate)3950 static void set_rate(struct slgt_info *info, u32 rate)
3951 {
3952 	unsigned int div;
3953 	unsigned int osc = info->base_clock;
3954 
3955 	/* div = osc/rate - 1
3956 	 *
3957 	 * Round div up if osc/rate is not integer to
3958 	 * force to next slowest rate.
3959 	 */
3960 
3961 	if (rate) {
3962 		div = osc/rate;
3963 		if (!(osc % rate) && div)
3964 			div--;
3965 		wr_reg16(info, BDR, (unsigned short)div);
3966 	}
3967 }
3968 
rx_stop(struct slgt_info * info)3969 static void rx_stop(struct slgt_info *info)
3970 {
3971 	unsigned short val;
3972 
3973 	/* disable and reset receiver */
3974 	val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3975 	wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3976 	wr_reg16(info, RCR, val);                  /* clear reset bit */
3977 
3978 	slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3979 
3980 	/* clear pending rx interrupts */
3981 	wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3982 
3983 	rdma_reset(info);
3984 
3985 	info->rx_enabled = false;
3986 	info->rx_restart = false;
3987 }
3988 
rx_start(struct slgt_info * info)3989 static void rx_start(struct slgt_info *info)
3990 {
3991 	unsigned short val;
3992 
3993 	slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3994 
3995 	/* clear pending rx overrun IRQ */
3996 	wr_reg16(info, SSR, IRQ_RXOVER);
3997 
3998 	/* reset and disable receiver */
3999 	val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
4000 	wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
4001 	wr_reg16(info, RCR, val);                  /* clear reset bit */
4002 
4003 	rdma_reset(info);
4004 	reset_rbufs(info);
4005 
4006 	if (info->rx_pio) {
4007 		/* rx request when rx FIFO not empty */
4008 		wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
4009 		slgt_irq_on(info, IRQ_RXDATA);
4010 		if (info->params.mode == MGSL_MODE_ASYNC) {
4011 			/* enable saving of rx status */
4012 			wr_reg32(info, RDCSR, BIT6);
4013 		}
4014 	} else {
4015 		/* rx request when rx FIFO half full */
4016 		wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
4017 		/* set 1st descriptor address */
4018 		wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
4019 
4020 		if (info->params.mode != MGSL_MODE_ASYNC) {
4021 			/* enable rx DMA and DMA interrupt */
4022 			wr_reg32(info, RDCSR, (BIT2 + BIT0));
4023 		} else {
4024 			/* enable saving of rx status, rx DMA and DMA interrupt */
4025 			wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
4026 		}
4027 	}
4028 
4029 	slgt_irq_on(info, IRQ_RXOVER);
4030 
4031 	/* enable receiver */
4032 	wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
4033 
4034 	info->rx_restart = false;
4035 	info->rx_enabled = true;
4036 }
4037 
tx_start(struct slgt_info * info)4038 static void tx_start(struct slgt_info *info)
4039 {
4040 	if (!info->tx_enabled) {
4041 		wr_reg16(info, TCR,
4042 			 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
4043 		info->tx_enabled = true;
4044 	}
4045 
4046 	if (desc_count(info->tbufs[info->tbuf_start])) {
4047 		info->drop_rts_on_tx_done = false;
4048 
4049 		if (info->params.mode != MGSL_MODE_ASYNC) {
4050 			if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
4051 				get_signals(info);
4052 				if (!(info->signals & SerialSignal_RTS)) {
4053 					info->signals |= SerialSignal_RTS;
4054 					set_signals(info);
4055 					info->drop_rts_on_tx_done = true;
4056 				}
4057 			}
4058 
4059 			slgt_irq_off(info, IRQ_TXDATA);
4060 			slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
4061 			/* clear tx idle and underrun status bits */
4062 			wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4063 		} else {
4064 			slgt_irq_off(info, IRQ_TXDATA);
4065 			slgt_irq_on(info, IRQ_TXIDLE);
4066 			/* clear tx idle status bit */
4067 			wr_reg16(info, SSR, IRQ_TXIDLE);
4068 		}
4069 		/* set 1st descriptor address and start DMA */
4070 		wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
4071 		wr_reg32(info, TDCSR, BIT2 + BIT0);
4072 		info->tx_active = true;
4073 	}
4074 }
4075 
tx_stop(struct slgt_info * info)4076 static void tx_stop(struct slgt_info *info)
4077 {
4078 	unsigned short val;
4079 
4080 	del_timer(&info->tx_timer);
4081 
4082 	tdma_reset(info);
4083 
4084 	/* reset and disable transmitter */
4085 	val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
4086 	wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
4087 
4088 	slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
4089 
4090 	/* clear tx idle and underrun status bit */
4091 	wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4092 
4093 	reset_tbufs(info);
4094 
4095 	info->tx_enabled = false;
4096 	info->tx_active = false;
4097 }
4098 
reset_port(struct slgt_info * info)4099 static void reset_port(struct slgt_info *info)
4100 {
4101 	if (!info->reg_addr)
4102 		return;
4103 
4104 	tx_stop(info);
4105 	rx_stop(info);
4106 
4107 	info->signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
4108 	set_signals(info);
4109 
4110 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4111 }
4112 
reset_adapter(struct slgt_info * info)4113 static void reset_adapter(struct slgt_info *info)
4114 {
4115 	int i;
4116 	for (i=0; i < info->port_count; ++i) {
4117 		if (info->port_array[i])
4118 			reset_port(info->port_array[i]);
4119 	}
4120 }
4121 
async_mode(struct slgt_info * info)4122 static void async_mode(struct slgt_info *info)
4123 {
4124   	unsigned short val;
4125 
4126 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4127 	tx_stop(info);
4128 	rx_stop(info);
4129 
4130 	/* TCR (tx control)
4131 	 *
4132 	 * 15..13  mode, 010=async
4133 	 * 12..10  encoding, 000=NRZ
4134 	 * 09      parity enable
4135 	 * 08      1=odd parity, 0=even parity
4136 	 * 07      1=RTS driver control
4137 	 * 06      1=break enable
4138 	 * 05..04  character length
4139 	 *         00=5 bits
4140 	 *         01=6 bits
4141 	 *         10=7 bits
4142 	 *         11=8 bits
4143 	 * 03      0=1 stop bit, 1=2 stop bits
4144 	 * 02      reset
4145 	 * 01      enable
4146 	 * 00      auto-CTS enable
4147 	 */
4148 	val = 0x4000;
4149 
4150 	if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4151 		val |= BIT7;
4152 
4153 	if (info->params.parity != ASYNC_PARITY_NONE) {
4154 		val |= BIT9;
4155 		if (info->params.parity == ASYNC_PARITY_ODD)
4156 			val |= BIT8;
4157 	}
4158 
4159 	switch (info->params.data_bits)
4160 	{
4161 	case 6: val |= BIT4; break;
4162 	case 7: val |= BIT5; break;
4163 	case 8: val |= BIT5 + BIT4; break;
4164 	}
4165 
4166 	if (info->params.stop_bits != 1)
4167 		val |= BIT3;
4168 
4169 	if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4170 		val |= BIT0;
4171 
4172 	wr_reg16(info, TCR, val);
4173 
4174 	/* RCR (rx control)
4175 	 *
4176 	 * 15..13  mode, 010=async
4177 	 * 12..10  encoding, 000=NRZ
4178 	 * 09      parity enable
4179 	 * 08      1=odd parity, 0=even parity
4180 	 * 07..06  reserved, must be 0
4181 	 * 05..04  character length
4182 	 *         00=5 bits
4183 	 *         01=6 bits
4184 	 *         10=7 bits
4185 	 *         11=8 bits
4186 	 * 03      reserved, must be zero
4187 	 * 02      reset
4188 	 * 01      enable
4189 	 * 00      auto-DCD enable
4190 	 */
4191 	val = 0x4000;
4192 
4193 	if (info->params.parity != ASYNC_PARITY_NONE) {
4194 		val |= BIT9;
4195 		if (info->params.parity == ASYNC_PARITY_ODD)
4196 			val |= BIT8;
4197 	}
4198 
4199 	switch (info->params.data_bits)
4200 	{
4201 	case 6: val |= BIT4; break;
4202 	case 7: val |= BIT5; break;
4203 	case 8: val |= BIT5 + BIT4; break;
4204 	}
4205 
4206 	if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4207 		val |= BIT0;
4208 
4209 	wr_reg16(info, RCR, val);
4210 
4211 	/* CCR (clock control)
4212 	 *
4213 	 * 07..05  011 = tx clock source is BRG/16
4214 	 * 04..02  010 = rx clock source is BRG
4215 	 * 01      0 = auxclk disabled
4216 	 * 00      1 = BRG enabled
4217 	 *
4218 	 * 0110 1001
4219 	 */
4220 	wr_reg8(info, CCR, 0x69);
4221 
4222 	msc_set_vcr(info);
4223 
4224 	/* SCR (serial control)
4225 	 *
4226 	 * 15  1=tx req on FIFO half empty
4227 	 * 14  1=rx req on FIFO half full
4228 	 * 13  tx data  IRQ enable
4229 	 * 12  tx idle  IRQ enable
4230 	 * 11  rx break on IRQ enable
4231 	 * 10  rx data  IRQ enable
4232 	 * 09  rx break off IRQ enable
4233 	 * 08  overrun  IRQ enable
4234 	 * 07  DSR      IRQ enable
4235 	 * 06  CTS      IRQ enable
4236 	 * 05  DCD      IRQ enable
4237 	 * 04  RI       IRQ enable
4238 	 * 03  0=16x sampling, 1=8x sampling
4239 	 * 02  1=txd->rxd internal loopback enable
4240 	 * 01  reserved, must be zero
4241 	 * 00  1=master IRQ enable
4242 	 */
4243 	val = BIT15 + BIT14 + BIT0;
4244 	/* JCR[8] : 1 = x8 async mode feature available */
4245 	if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
4246 	    ((info->base_clock < (info->params.data_rate * 16)) ||
4247 	     (info->base_clock % (info->params.data_rate * 16)))) {
4248 		/* use 8x sampling */
4249 		val |= BIT3;
4250 		set_rate(info, info->params.data_rate * 8);
4251 	} else {
4252 		/* use 16x sampling */
4253 		set_rate(info, info->params.data_rate * 16);
4254 	}
4255 	wr_reg16(info, SCR, val);
4256 
4257 	slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4258 
4259 	if (info->params.loopback)
4260 		enable_loopback(info);
4261 }
4262 
sync_mode(struct slgt_info * info)4263 static void sync_mode(struct slgt_info *info)
4264 {
4265 	unsigned short val;
4266 
4267 	slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4268 	tx_stop(info);
4269 	rx_stop(info);
4270 
4271 	/* TCR (tx control)
4272 	 *
4273 	 * 15..13  mode
4274 	 *         000=HDLC/SDLC
4275 	 *         001=raw bit synchronous
4276 	 *         010=asynchronous/isochronous
4277 	 *         011=monosync byte synchronous
4278 	 *         100=bisync byte synchronous
4279 	 *         101=xsync byte synchronous
4280 	 * 12..10  encoding
4281 	 * 09      CRC enable
4282 	 * 08      CRC32
4283 	 * 07      1=RTS driver control
4284 	 * 06      preamble enable
4285 	 * 05..04  preamble length
4286 	 * 03      share open/close flag
4287 	 * 02      reset
4288 	 * 01      enable
4289 	 * 00      auto-CTS enable
4290 	 */
4291 	val = BIT2;
4292 
4293 	switch(info->params.mode) {
4294 	case MGSL_MODE_XSYNC:
4295 		val |= BIT15 + BIT13;
4296 		break;
4297 	case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4298 	case MGSL_MODE_BISYNC:   val |= BIT15; break;
4299 	case MGSL_MODE_RAW:      val |= BIT13; break;
4300 	}
4301 	if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4302 		val |= BIT7;
4303 
4304 	switch(info->params.encoding)
4305 	{
4306 	case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4307 	case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4308 	case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4309 	case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4310 	case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4311 	case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4312 	case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4313 	}
4314 
4315 	switch (info->params.crc_type & HDLC_CRC_MASK)
4316 	{
4317 	case HDLC_CRC_16_CCITT: val |= BIT9; break;
4318 	case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4319 	}
4320 
4321 	if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4322 		val |= BIT6;
4323 
4324 	switch (info->params.preamble_length)
4325 	{
4326 	case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4327 	case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4328 	case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4329 	}
4330 
4331 	if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4332 		val |= BIT0;
4333 
4334 	wr_reg16(info, TCR, val);
4335 
4336 	/* TPR (transmit preamble) */
4337 
4338 	switch (info->params.preamble)
4339 	{
4340 	case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4341 	case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4342 	case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4343 	case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4344 	case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4345 	default:                          val = 0x7e; break;
4346 	}
4347 	wr_reg8(info, TPR, (unsigned char)val);
4348 
4349 	/* RCR (rx control)
4350 	 *
4351 	 * 15..13  mode
4352 	 *         000=HDLC/SDLC
4353 	 *         001=raw bit synchronous
4354 	 *         010=asynchronous/isochronous
4355 	 *         011=monosync byte synchronous
4356 	 *         100=bisync byte synchronous
4357 	 *         101=xsync byte synchronous
4358 	 * 12..10  encoding
4359 	 * 09      CRC enable
4360 	 * 08      CRC32
4361 	 * 07..03  reserved, must be 0
4362 	 * 02      reset
4363 	 * 01      enable
4364 	 * 00      auto-DCD enable
4365 	 */
4366 	val = 0;
4367 
4368 	switch(info->params.mode) {
4369 	case MGSL_MODE_XSYNC:
4370 		val |= BIT15 + BIT13;
4371 		break;
4372 	case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4373 	case MGSL_MODE_BISYNC:   val |= BIT15; break;
4374 	case MGSL_MODE_RAW:      val |= BIT13; break;
4375 	}
4376 
4377 	switch(info->params.encoding)
4378 	{
4379 	case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4380 	case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4381 	case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4382 	case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4383 	case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4384 	case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4385 	case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4386 	}
4387 
4388 	switch (info->params.crc_type & HDLC_CRC_MASK)
4389 	{
4390 	case HDLC_CRC_16_CCITT: val |= BIT9; break;
4391 	case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4392 	}
4393 
4394 	if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4395 		val |= BIT0;
4396 
4397 	wr_reg16(info, RCR, val);
4398 
4399 	/* CCR (clock control)
4400 	 *
4401 	 * 07..05  tx clock source
4402 	 * 04..02  rx clock source
4403 	 * 01      auxclk enable
4404 	 * 00      BRG enable
4405 	 */
4406 	val = 0;
4407 
4408 	if (info->params.flags & HDLC_FLAG_TXC_BRG)
4409 	{
4410 		// when RxC source is DPLL, BRG generates 16X DPLL
4411 		// reference clock, so take TxC from BRG/16 to get
4412 		// transmit clock at actual data rate
4413 		if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4414 			val |= BIT6 + BIT5;	/* 011, txclk = BRG/16 */
4415 		else
4416 			val |= BIT6;	/* 010, txclk = BRG */
4417 	}
4418 	else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4419 		val |= BIT7;	/* 100, txclk = DPLL Input */
4420 	else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4421 		val |= BIT5;	/* 001, txclk = RXC Input */
4422 
4423 	if (info->params.flags & HDLC_FLAG_RXC_BRG)
4424 		val |= BIT3;	/* 010, rxclk = BRG */
4425 	else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4426 		val |= BIT4;	/* 100, rxclk = DPLL */
4427 	else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4428 		val |= BIT2;	/* 001, rxclk = TXC Input */
4429 
4430 	if (info->params.clock_speed)
4431 		val |= BIT1 + BIT0;
4432 
4433 	wr_reg8(info, CCR, (unsigned char)val);
4434 
4435 	if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4436 	{
4437 		// program DPLL mode
4438 		switch(info->params.encoding)
4439 		{
4440 		case HDLC_ENCODING_BIPHASE_MARK:
4441 		case HDLC_ENCODING_BIPHASE_SPACE:
4442 			val = BIT7; break;
4443 		case HDLC_ENCODING_BIPHASE_LEVEL:
4444 		case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4445 			val = BIT7 + BIT6; break;
4446 		default: val = BIT6;	// NRZ encodings
4447 		}
4448 		wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4449 
4450 		// DPLL requires a 16X reference clock from BRG
4451 		set_rate(info, info->params.clock_speed * 16);
4452 	}
4453 	else
4454 		set_rate(info, info->params.clock_speed);
4455 
4456 	tx_set_idle(info);
4457 
4458 	msc_set_vcr(info);
4459 
4460 	/* SCR (serial control)
4461 	 *
4462 	 * 15  1=tx req on FIFO half empty
4463 	 * 14  1=rx req on FIFO half full
4464 	 * 13  tx data  IRQ enable
4465 	 * 12  tx idle  IRQ enable
4466 	 * 11  underrun IRQ enable
4467 	 * 10  rx data  IRQ enable
4468 	 * 09  rx idle  IRQ enable
4469 	 * 08  overrun  IRQ enable
4470 	 * 07  DSR      IRQ enable
4471 	 * 06  CTS      IRQ enable
4472 	 * 05  DCD      IRQ enable
4473 	 * 04  RI       IRQ enable
4474 	 * 03  reserved, must be zero
4475 	 * 02  1=txd->rxd internal loopback enable
4476 	 * 01  reserved, must be zero
4477 	 * 00  1=master IRQ enable
4478 	 */
4479 	wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4480 
4481 	if (info->params.loopback)
4482 		enable_loopback(info);
4483 }
4484 
4485 /*
4486  *  set transmit idle mode
4487  */
tx_set_idle(struct slgt_info * info)4488 static void tx_set_idle(struct slgt_info *info)
4489 {
4490 	unsigned char val;
4491 	unsigned short tcr;
4492 
4493 	/* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4494 	 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4495 	 */
4496 	tcr = rd_reg16(info, TCR);
4497 	if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4498 		/* disable preamble, set idle size to 16 bits */
4499 		tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4500 		/* MSB of 16 bit idle specified in tx preamble register (TPR) */
4501 		wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4502 	} else if (!(tcr & BIT6)) {
4503 		/* preamble is disabled, set idle size to 8 bits */
4504 		tcr &= ~(BIT5 + BIT4);
4505 	}
4506 	wr_reg16(info, TCR, tcr);
4507 
4508 	if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4509 		/* LSB of custom tx idle specified in tx idle register */
4510 		val = (unsigned char)(info->idle_mode & 0xff);
4511 	} else {
4512 		/* standard 8 bit idle patterns */
4513 		switch(info->idle_mode)
4514 		{
4515 		case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4516 		case HDLC_TXIDLE_ALT_ZEROS_ONES:
4517 		case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4518 		case HDLC_TXIDLE_ZEROS:
4519 		case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4520 		default:                         val = 0xff;
4521 		}
4522 	}
4523 
4524 	wr_reg8(info, TIR, val);
4525 }
4526 
4527 /*
4528  * get state of V24 status (input) signals
4529  */
get_signals(struct slgt_info * info)4530 static void get_signals(struct slgt_info *info)
4531 {
4532 	unsigned short status = rd_reg16(info, SSR);
4533 
4534 	/* clear all serial signals except DTR and RTS */
4535 	info->signals &= SerialSignal_DTR + SerialSignal_RTS;
4536 
4537 	if (status & BIT3)
4538 		info->signals |= SerialSignal_DSR;
4539 	if (status & BIT2)
4540 		info->signals |= SerialSignal_CTS;
4541 	if (status & BIT1)
4542 		info->signals |= SerialSignal_DCD;
4543 	if (status & BIT0)
4544 		info->signals |= SerialSignal_RI;
4545 }
4546 
4547 /*
4548  * set V.24 Control Register based on current configuration
4549  */
msc_set_vcr(struct slgt_info * info)4550 static void msc_set_vcr(struct slgt_info *info)
4551 {
4552 	unsigned char val = 0;
4553 
4554 	/* VCR (V.24 control)
4555 	 *
4556 	 * 07..04  serial IF select
4557 	 * 03      DTR
4558 	 * 02      RTS
4559 	 * 01      LL
4560 	 * 00      RL
4561 	 */
4562 
4563 	switch(info->if_mode & MGSL_INTERFACE_MASK)
4564 	{
4565 	case MGSL_INTERFACE_RS232:
4566 		val |= BIT5; /* 0010 */
4567 		break;
4568 	case MGSL_INTERFACE_V35:
4569 		val |= BIT7 + BIT6 + BIT5; /* 1110 */
4570 		break;
4571 	case MGSL_INTERFACE_RS422:
4572 		val |= BIT6; /* 0100 */
4573 		break;
4574 	}
4575 
4576 	if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4577 		val |= BIT4;
4578 	if (info->signals & SerialSignal_DTR)
4579 		val |= BIT3;
4580 	if (info->signals & SerialSignal_RTS)
4581 		val |= BIT2;
4582 	if (info->if_mode & MGSL_INTERFACE_LL)
4583 		val |= BIT1;
4584 	if (info->if_mode & MGSL_INTERFACE_RL)
4585 		val |= BIT0;
4586 	wr_reg8(info, VCR, val);
4587 }
4588 
4589 /*
4590  * set state of V24 control (output) signals
4591  */
set_signals(struct slgt_info * info)4592 static void set_signals(struct slgt_info *info)
4593 {
4594 	unsigned char val = rd_reg8(info, VCR);
4595 	if (info->signals & SerialSignal_DTR)
4596 		val |= BIT3;
4597 	else
4598 		val &= ~BIT3;
4599 	if (info->signals & SerialSignal_RTS)
4600 		val |= BIT2;
4601 	else
4602 		val &= ~BIT2;
4603 	wr_reg8(info, VCR, val);
4604 }
4605 
4606 /*
4607  * free range of receive DMA buffers (i to last)
4608  */
free_rbufs(struct slgt_info * info,unsigned int i,unsigned int last)4609 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4610 {
4611 	int done = 0;
4612 
4613 	while(!done) {
4614 		/* reset current buffer for reuse */
4615 		info->rbufs[i].status = 0;
4616 		set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4617 		if (i == last)
4618 			done = 1;
4619 		if (++i == info->rbuf_count)
4620 			i = 0;
4621 	}
4622 	info->rbuf_current = i;
4623 }
4624 
4625 /*
4626  * mark all receive DMA buffers as free
4627  */
reset_rbufs(struct slgt_info * info)4628 static void reset_rbufs(struct slgt_info *info)
4629 {
4630 	free_rbufs(info, 0, info->rbuf_count - 1);
4631 	info->rbuf_fill_index = 0;
4632 	info->rbuf_fill_count = 0;
4633 }
4634 
4635 /*
4636  * pass receive HDLC frame to upper layer
4637  *
4638  * return true if frame available, otherwise false
4639  */
rx_get_frame(struct slgt_info * info)4640 static bool rx_get_frame(struct slgt_info *info)
4641 {
4642 	unsigned int start, end;
4643 	unsigned short status;
4644 	unsigned int framesize = 0;
4645 	unsigned long flags;
4646 	struct tty_struct *tty = info->port.tty;
4647 	unsigned char addr_field = 0xff;
4648 	unsigned int crc_size = 0;
4649 
4650 	switch (info->params.crc_type & HDLC_CRC_MASK) {
4651 	case HDLC_CRC_16_CCITT: crc_size = 2; break;
4652 	case HDLC_CRC_32_CCITT: crc_size = 4; break;
4653 	}
4654 
4655 check_again:
4656 
4657 	framesize = 0;
4658 	addr_field = 0xff;
4659 	start = end = info->rbuf_current;
4660 
4661 	for (;;) {
4662 		if (!desc_complete(info->rbufs[end]))
4663 			goto cleanup;
4664 
4665 		if (framesize == 0 && info->params.addr_filter != 0xff)
4666 			addr_field = info->rbufs[end].buf[0];
4667 
4668 		framesize += desc_count(info->rbufs[end]);
4669 
4670 		if (desc_eof(info->rbufs[end]))
4671 			break;
4672 
4673 		if (++end == info->rbuf_count)
4674 			end = 0;
4675 
4676 		if (end == info->rbuf_current) {
4677 			if (info->rx_enabled){
4678 				spin_lock_irqsave(&info->lock,flags);
4679 				rx_start(info);
4680 				spin_unlock_irqrestore(&info->lock,flags);
4681 			}
4682 			goto cleanup;
4683 		}
4684 	}
4685 
4686 	/* status
4687 	 *
4688 	 * 15      buffer complete
4689 	 * 14..06  reserved
4690 	 * 05..04  residue
4691 	 * 02      eof (end of frame)
4692 	 * 01      CRC error
4693 	 * 00      abort
4694 	 */
4695 	status = desc_status(info->rbufs[end]);
4696 
4697 	/* ignore CRC bit if not using CRC (bit is undefined) */
4698 	if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4699 		status &= ~BIT1;
4700 
4701 	if (framesize == 0 ||
4702 		 (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4703 		free_rbufs(info, start, end);
4704 		goto check_again;
4705 	}
4706 
4707 	if (framesize < (2 + crc_size) || status & BIT0) {
4708 		info->icount.rxshort++;
4709 		framesize = 0;
4710 	} else if (status & BIT1) {
4711 		info->icount.rxcrc++;
4712 		if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4713 			framesize = 0;
4714 	}
4715 
4716 #if SYNCLINK_GENERIC_HDLC
4717 	if (framesize == 0) {
4718 		info->netdev->stats.rx_errors++;
4719 		info->netdev->stats.rx_frame_errors++;
4720 	}
4721 #endif
4722 
4723 	DBGBH(("%s rx frame status=%04X size=%d\n",
4724 		info->device_name, status, framesize));
4725 	DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4726 
4727 	if (framesize) {
4728 		if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4729 			framesize -= crc_size;
4730 			crc_size = 0;
4731 		}
4732 
4733 		if (framesize > info->max_frame_size + crc_size)
4734 			info->icount.rxlong++;
4735 		else {
4736 			/* copy dma buffer(s) to contiguous temp buffer */
4737 			int copy_count = framesize;
4738 			int i = start;
4739 			unsigned char *p = info->tmp_rbuf;
4740 			info->tmp_rbuf_count = framesize;
4741 
4742 			info->icount.rxok++;
4743 
4744 			while(copy_count) {
4745 				int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4746 				memcpy(p, info->rbufs[i].buf, partial_count);
4747 				p += partial_count;
4748 				copy_count -= partial_count;
4749 				if (++i == info->rbuf_count)
4750 					i = 0;
4751 			}
4752 
4753 			if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4754 				*p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4755 				framesize++;
4756 			}
4757 
4758 #if SYNCLINK_GENERIC_HDLC
4759 			if (info->netcount)
4760 				hdlcdev_rx(info,info->tmp_rbuf, framesize);
4761 			else
4762 #endif
4763 				ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4764 		}
4765 	}
4766 	free_rbufs(info, start, end);
4767 	return true;
4768 
4769 cleanup:
4770 	return false;
4771 }
4772 
4773 /*
4774  * pass receive buffer (RAW synchronous mode) to tty layer
4775  * return true if buffer available, otherwise false
4776  */
rx_get_buf(struct slgt_info * info)4777 static bool rx_get_buf(struct slgt_info *info)
4778 {
4779 	unsigned int i = info->rbuf_current;
4780 	unsigned int count;
4781 
4782 	if (!desc_complete(info->rbufs[i]))
4783 		return false;
4784 	count = desc_count(info->rbufs[i]);
4785 	switch(info->params.mode) {
4786 	case MGSL_MODE_MONOSYNC:
4787 	case MGSL_MODE_BISYNC:
4788 	case MGSL_MODE_XSYNC:
4789 		/* ignore residue in byte synchronous modes */
4790 		if (desc_residue(info->rbufs[i]))
4791 			count--;
4792 		break;
4793 	}
4794 	DBGDATA(info, info->rbufs[i].buf, count, "rx");
4795 	DBGINFO(("rx_get_buf size=%d\n", count));
4796 	if (count)
4797 		ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4798 				  info->flag_buf, count);
4799 	free_rbufs(info, i, i);
4800 	return true;
4801 }
4802 
reset_tbufs(struct slgt_info * info)4803 static void reset_tbufs(struct slgt_info *info)
4804 {
4805 	unsigned int i;
4806 	info->tbuf_current = 0;
4807 	for (i=0 ; i < info->tbuf_count ; i++) {
4808 		info->tbufs[i].status = 0;
4809 		info->tbufs[i].count  = 0;
4810 	}
4811 }
4812 
4813 /*
4814  * return number of free transmit DMA buffers
4815  */
free_tbuf_count(struct slgt_info * info)4816 static unsigned int free_tbuf_count(struct slgt_info *info)
4817 {
4818 	unsigned int count = 0;
4819 	unsigned int i = info->tbuf_current;
4820 
4821 	do
4822 	{
4823 		if (desc_count(info->tbufs[i]))
4824 			break; /* buffer in use */
4825 		++count;
4826 		if (++i == info->tbuf_count)
4827 			i=0;
4828 	} while (i != info->tbuf_current);
4829 
4830 	/* if tx DMA active, last zero count buffer is in use */
4831 	if (count && (rd_reg32(info, TDCSR) & BIT0))
4832 		--count;
4833 
4834 	return count;
4835 }
4836 
4837 /*
4838  * return number of bytes in unsent transmit DMA buffers
4839  * and the serial controller tx FIFO
4840  */
tbuf_bytes(struct slgt_info * info)4841 static unsigned int tbuf_bytes(struct slgt_info *info)
4842 {
4843 	unsigned int total_count = 0;
4844 	unsigned int i = info->tbuf_current;
4845 	unsigned int reg_value;
4846 	unsigned int count;
4847 	unsigned int active_buf_count = 0;
4848 
4849 	/*
4850 	 * Add descriptor counts for all tx DMA buffers.
4851 	 * If count is zero (cleared by DMA controller after read),
4852 	 * the buffer is complete or is actively being read from.
4853 	 *
4854 	 * Record buf_count of last buffer with zero count starting
4855 	 * from current ring position. buf_count is mirror
4856 	 * copy of count and is not cleared by serial controller.
4857 	 * If DMA controller is active, that buffer is actively
4858 	 * being read so add to total.
4859 	 */
4860 	do {
4861 		count = desc_count(info->tbufs[i]);
4862 		if (count)
4863 			total_count += count;
4864 		else if (!total_count)
4865 			active_buf_count = info->tbufs[i].buf_count;
4866 		if (++i == info->tbuf_count)
4867 			i = 0;
4868 	} while (i != info->tbuf_current);
4869 
4870 	/* read tx DMA status register */
4871 	reg_value = rd_reg32(info, TDCSR);
4872 
4873 	/* if tx DMA active, last zero count buffer is in use */
4874 	if (reg_value & BIT0)
4875 		total_count += active_buf_count;
4876 
4877 	/* add tx FIFO count = reg_value[15..8] */
4878 	total_count += (reg_value >> 8) & 0xff;
4879 
4880 	/* if transmitter active add one byte for shift register */
4881 	if (info->tx_active)
4882 		total_count++;
4883 
4884 	return total_count;
4885 }
4886 
4887 /*
4888  * load data into transmit DMA buffer ring and start transmitter if needed
4889  * return true if data accepted, otherwise false (buffers full)
4890  */
tx_load(struct slgt_info * info,const char * buf,unsigned int size)4891 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4892 {
4893 	unsigned short count;
4894 	unsigned int i;
4895 	struct slgt_desc *d;
4896 
4897 	/* check required buffer space */
4898 	if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info))
4899 		return false;
4900 
4901 	DBGDATA(info, buf, size, "tx");
4902 
4903 	/*
4904 	 * copy data to one or more DMA buffers in circular ring
4905 	 * tbuf_start   = first buffer for this data
4906 	 * tbuf_current = next free buffer
4907 	 *
4908 	 * Copy all data before making data visible to DMA controller by
4909 	 * setting descriptor count of the first buffer.
4910 	 * This prevents an active DMA controller from reading the first DMA
4911 	 * buffers of a frame and stopping before the final buffers are filled.
4912 	 */
4913 
4914 	info->tbuf_start = i = info->tbuf_current;
4915 
4916 	while (size) {
4917 		d = &info->tbufs[i];
4918 
4919 		count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4920 		memcpy(d->buf, buf, count);
4921 
4922 		size -= count;
4923 		buf  += count;
4924 
4925 		/*
4926 		 * set EOF bit for last buffer of HDLC frame or
4927 		 * for every buffer in raw mode
4928 		 */
4929 		if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4930 		    info->params.mode == MGSL_MODE_RAW)
4931 			set_desc_eof(*d, 1);
4932 		else
4933 			set_desc_eof(*d, 0);
4934 
4935 		/* set descriptor count for all but first buffer */
4936 		if (i != info->tbuf_start)
4937 			set_desc_count(*d, count);
4938 		d->buf_count = count;
4939 
4940 		if (++i == info->tbuf_count)
4941 			i = 0;
4942 	}
4943 
4944 	info->tbuf_current = i;
4945 
4946 	/* set first buffer count to make new data visible to DMA controller */
4947 	d = &info->tbufs[info->tbuf_start];
4948 	set_desc_count(*d, d->buf_count);
4949 
4950 	/* start transmitter if needed and update transmit timeout */
4951 	if (!info->tx_active)
4952 		tx_start(info);
4953 	update_tx_timer(info);
4954 
4955 	return true;
4956 }
4957 
register_test(struct slgt_info * info)4958 static int register_test(struct slgt_info *info)
4959 {
4960 	static unsigned short patterns[] =
4961 		{0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4962 	static unsigned int count = ARRAY_SIZE(patterns);
4963 	unsigned int i;
4964 	int rc = 0;
4965 
4966 	for (i=0 ; i < count ; i++) {
4967 		wr_reg16(info, TIR, patterns[i]);
4968 		wr_reg16(info, BDR, patterns[(i+1)%count]);
4969 		if ((rd_reg16(info, TIR) != patterns[i]) ||
4970 		    (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4971 			rc = -ENODEV;
4972 			break;
4973 		}
4974 	}
4975 	info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4976 	info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4977 	return rc;
4978 }
4979 
irq_test(struct slgt_info * info)4980 static int irq_test(struct slgt_info *info)
4981 {
4982 	unsigned long timeout;
4983 	unsigned long flags;
4984 	struct tty_struct *oldtty = info->port.tty;
4985 	u32 speed = info->params.data_rate;
4986 
4987 	info->params.data_rate = 921600;
4988 	info->port.tty = NULL;
4989 
4990 	spin_lock_irqsave(&info->lock, flags);
4991 	async_mode(info);
4992 	slgt_irq_on(info, IRQ_TXIDLE);
4993 
4994 	/* enable transmitter */
4995 	wr_reg16(info, TCR,
4996 		(unsigned short)(rd_reg16(info, TCR) | BIT1));
4997 
4998 	/* write one byte and wait for tx idle */
4999 	wr_reg16(info, TDR, 0);
5000 
5001 	/* assume failure */
5002 	info->init_error = DiagStatus_IrqFailure;
5003 	info->irq_occurred = false;
5004 
5005 	spin_unlock_irqrestore(&info->lock, flags);
5006 
5007 	timeout=100;
5008 	while(timeout-- && !info->irq_occurred)
5009 		msleep_interruptible(10);
5010 
5011 	spin_lock_irqsave(&info->lock,flags);
5012 	reset_port(info);
5013 	spin_unlock_irqrestore(&info->lock,flags);
5014 
5015 	info->params.data_rate = speed;
5016 	info->port.tty = oldtty;
5017 
5018 	info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
5019 	return info->irq_occurred ? 0 : -ENODEV;
5020 }
5021 
loopback_test_rx(struct slgt_info * info)5022 static int loopback_test_rx(struct slgt_info *info)
5023 {
5024 	unsigned char *src, *dest;
5025 	int count;
5026 
5027 	if (desc_complete(info->rbufs[0])) {
5028 		count = desc_count(info->rbufs[0]);
5029 		src   = info->rbufs[0].buf;
5030 		dest  = info->tmp_rbuf;
5031 
5032 		for( ; count ; count-=2, src+=2) {
5033 			/* src=data byte (src+1)=status byte */
5034 			if (!(*(src+1) & (BIT9 + BIT8))) {
5035 				*dest = *src;
5036 				dest++;
5037 				info->tmp_rbuf_count++;
5038 			}
5039 		}
5040 		DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
5041 		return 1;
5042 	}
5043 	return 0;
5044 }
5045 
loopback_test(struct slgt_info * info)5046 static int loopback_test(struct slgt_info *info)
5047 {
5048 #define TESTFRAMESIZE 20
5049 
5050 	unsigned long timeout;
5051 	u16 count = TESTFRAMESIZE;
5052 	unsigned char buf[TESTFRAMESIZE];
5053 	int rc = -ENODEV;
5054 	unsigned long flags;
5055 
5056 	struct tty_struct *oldtty = info->port.tty;
5057 	MGSL_PARAMS params;
5058 
5059 	memcpy(&params, &info->params, sizeof(params));
5060 
5061 	info->params.mode = MGSL_MODE_ASYNC;
5062 	info->params.data_rate = 921600;
5063 	info->params.loopback = 1;
5064 	info->port.tty = NULL;
5065 
5066 	/* build and send transmit frame */
5067 	for (count = 0; count < TESTFRAMESIZE; ++count)
5068 		buf[count] = (unsigned char)count;
5069 
5070 	info->tmp_rbuf_count = 0;
5071 	memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
5072 
5073 	/* program hardware for HDLC and enabled receiver */
5074 	spin_lock_irqsave(&info->lock,flags);
5075 	async_mode(info);
5076 	rx_start(info);
5077 	tx_load(info, buf, count);
5078 	spin_unlock_irqrestore(&info->lock, flags);
5079 
5080 	/* wait for receive complete */
5081 	for (timeout = 100; timeout; --timeout) {
5082 		msleep_interruptible(10);
5083 		if (loopback_test_rx(info)) {
5084 			rc = 0;
5085 			break;
5086 		}
5087 	}
5088 
5089 	/* verify received frame length and contents */
5090 	if (!rc && (info->tmp_rbuf_count != count ||
5091 		  memcmp(buf, info->tmp_rbuf, count))) {
5092 		rc = -ENODEV;
5093 	}
5094 
5095 	spin_lock_irqsave(&info->lock,flags);
5096 	reset_adapter(info);
5097 	spin_unlock_irqrestore(&info->lock,flags);
5098 
5099 	memcpy(&info->params, &params, sizeof(info->params));
5100 	info->port.tty = oldtty;
5101 
5102 	info->init_error = rc ? DiagStatus_DmaFailure : 0;
5103 	return rc;
5104 }
5105 
adapter_test(struct slgt_info * info)5106 static int adapter_test(struct slgt_info *info)
5107 {
5108 	DBGINFO(("testing %s\n", info->device_name));
5109 	if (register_test(info) < 0) {
5110 		printk("register test failure %s addr=%08X\n",
5111 			info->device_name, info->phys_reg_addr);
5112 	} else if (irq_test(info) < 0) {
5113 		printk("IRQ test failure %s IRQ=%d\n",
5114 			info->device_name, info->irq_level);
5115 	} else if (loopback_test(info) < 0) {
5116 		printk("loopback test failure %s\n", info->device_name);
5117 	}
5118 	return info->init_error;
5119 }
5120 
5121 /*
5122  * transmit timeout handler
5123  */
tx_timeout(unsigned long context)5124 static void tx_timeout(unsigned long context)
5125 {
5126 	struct slgt_info *info = (struct slgt_info*)context;
5127 	unsigned long flags;
5128 
5129 	DBGINFO(("%s tx_timeout\n", info->device_name));
5130 	if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
5131 		info->icount.txtimeout++;
5132 	}
5133 	spin_lock_irqsave(&info->lock,flags);
5134 	tx_stop(info);
5135 	spin_unlock_irqrestore(&info->lock,flags);
5136 
5137 #if SYNCLINK_GENERIC_HDLC
5138 	if (info->netcount)
5139 		hdlcdev_tx_done(info);
5140 	else
5141 #endif
5142 		bh_transmit(info);
5143 }
5144 
5145 /*
5146  * receive buffer polling timer
5147  */
rx_timeout(unsigned long context)5148 static void rx_timeout(unsigned long context)
5149 {
5150 	struct slgt_info *info = (struct slgt_info*)context;
5151 	unsigned long flags;
5152 
5153 	DBGINFO(("%s rx_timeout\n", info->device_name));
5154 	spin_lock_irqsave(&info->lock, flags);
5155 	info->pending_bh |= BH_RECEIVE;
5156 	spin_unlock_irqrestore(&info->lock, flags);
5157 	bh_handler(&info->task);
5158 }
5159 
5160