1 /*
2  * include/linux/serial_reg.h
3  *
4  * Copyright (C) 1992, 1994 by Theodore Ts'o.
5  *
6  * Redistribution of this file is permitted under the terms of the GNU
7  * Public License (GPL)
8  *
9  * These are the UART port assignments, expressed as offsets from the base
10  * register.  These assignments should hold for any serial port based on
11  * a 8250, 16450, or 16550(A).
12  */
13 
14 #ifndef _LINUX_SERIAL_REG_H
15 #define _LINUX_SERIAL_REG_H
16 
17 /*
18  * DLAB=0
19  */
20 #define UART_RX		0	/* In:  Receive buffer */
21 #define UART_TX		0	/* Out: Transmit buffer */
22 
23 #define UART_IER	1	/* Out: Interrupt Enable Register */
24 #define UART_IER_MSI		0x08 /* Enable Modem status interrupt */
25 #define UART_IER_RLSI		0x04 /* Enable receiver line status interrupt */
26 #define UART_IER_THRI		0x02 /* Enable Transmitter holding register int. */
27 #define UART_IER_RDI		0x01 /* Enable receiver data interrupt */
28 /*
29  * Sleep mode for ST16650 and TI16750.  For the ST16650, EFR[4]=1
30  */
31 #define UART_IERX_SLEEP		0x10 /* Enable sleep mode */
32 
33 #define UART_IIR	2	/* In:  Interrupt ID Register */
34 #define UART_IIR_NO_INT		0x01 /* No interrupts pending */
35 #define UART_IIR_ID		0x06 /* Mask for the interrupt ID */
36 #define UART_IIR_MSI		0x00 /* Modem status interrupt */
37 #define UART_IIR_THRI		0x02 /* Transmitter holding register empty */
38 #define UART_IIR_RDI		0x04 /* Receiver data interrupt */
39 #define UART_IIR_RLSI		0x06 /* Receiver line status interrupt */
40 
41 #define UART_IIR_BUSY		0x07 /* DesignWare APB Busy Detect */
42 
43 #define UART_FCR	2	/* Out: FIFO Control Register */
44 #define UART_FCR_ENABLE_FIFO	0x01 /* Enable the FIFO */
45 #define UART_FCR_CLEAR_RCVR	0x02 /* Clear the RCVR FIFO */
46 #define UART_FCR_CLEAR_XMIT	0x04 /* Clear the XMIT FIFO */
47 #define UART_FCR_DMA_SELECT	0x08 /* For DMA applications */
48 /*
49  * Note: The FIFO trigger levels are chip specific:
50  *	RX:76 = 00  01  10  11	TX:54 = 00  01  10  11
51  * PC16550D:	 1   4   8  14		xx  xx  xx  xx
52  * TI16C550A:	 1   4   8  14          xx  xx  xx  xx
53  * TI16C550C:	 1   4   8  14          xx  xx  xx  xx
54  * ST16C550:	 1   4   8  14		xx  xx  xx  xx
55  * ST16C650:	 8  16  24  28		16   8  24  30	PORT_16650V2
56  * NS16C552:	 1   4   8  14		xx  xx  xx  xx
57  * ST16C654:	 8  16  56  60		 8  16  32  56	PORT_16654
58  * TI16C750:	 1  16  32  56		xx  xx  xx  xx	PORT_16750
59  * TI16C752:	 8  16  56  60		 8  16  32  56
60  * Tegra:	 1   4   8  14		16   8   4   1	PORT_TEGRA
61  */
62 #define UART_FCR_R_TRIG_00	0x00
63 #define UART_FCR_R_TRIG_01	0x40
64 #define UART_FCR_R_TRIG_10	0x80
65 #define UART_FCR_R_TRIG_11	0xc0
66 #define UART_FCR_T_TRIG_00	0x00
67 #define UART_FCR_T_TRIG_01	0x10
68 #define UART_FCR_T_TRIG_10	0x20
69 #define UART_FCR_T_TRIG_11	0x30
70 
71 #define UART_FCR_TRIGGER_MASK	0xC0 /* Mask for the FIFO trigger range */
72 #define UART_FCR_TRIGGER_1	0x00 /* Mask for trigger set at 1 */
73 #define UART_FCR_TRIGGER_4	0x40 /* Mask for trigger set at 4 */
74 #define UART_FCR_TRIGGER_8	0x80 /* Mask for trigger set at 8 */
75 #define UART_FCR_TRIGGER_14	0xC0 /* Mask for trigger set at 14 */
76 /* 16650 definitions */
77 #define UART_FCR6_R_TRIGGER_8	0x00 /* Mask for receive trigger set at 1 */
78 #define UART_FCR6_R_TRIGGER_16	0x40 /* Mask for receive trigger set at 4 */
79 #define UART_FCR6_R_TRIGGER_24  0x80 /* Mask for receive trigger set at 8 */
80 #define UART_FCR6_R_TRIGGER_28	0xC0 /* Mask for receive trigger set at 14 */
81 #define UART_FCR6_T_TRIGGER_16	0x00 /* Mask for transmit trigger set at 16 */
82 #define UART_FCR6_T_TRIGGER_8	0x10 /* Mask for transmit trigger set at 8 */
83 #define UART_FCR6_T_TRIGGER_24  0x20 /* Mask for transmit trigger set at 24 */
84 #define UART_FCR6_T_TRIGGER_30	0x30 /* Mask for transmit trigger set at 30 */
85 #define UART_FCR7_64BYTE	0x20 /* Go into 64 byte mode (TI16C750) */
86 
87 #define UART_LCR	3	/* Out: Line Control Register */
88 /*
89  * Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
90  * UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
91  */
92 #define UART_LCR_DLAB		0x80 /* Divisor latch access bit */
93 #define UART_LCR_SBC		0x40 /* Set break control */
94 #define UART_LCR_SPAR		0x20 /* Stick parity (?) */
95 #define UART_LCR_EPAR		0x10 /* Even parity select */
96 #define UART_LCR_PARITY		0x08 /* Parity Enable */
97 #define UART_LCR_STOP		0x04 /* Stop bits: 0=1 bit, 1=2 bits */
98 #define UART_LCR_WLEN5		0x00 /* Wordlength: 5 bits */
99 #define UART_LCR_WLEN6		0x01 /* Wordlength: 6 bits */
100 #define UART_LCR_WLEN7		0x02 /* Wordlength: 7 bits */
101 #define UART_LCR_WLEN8		0x03 /* Wordlength: 8 bits */
102 
103 /*
104  * Access to some registers depends on register access / configuration
105  * mode.
106  */
107 #define UART_LCR_CONF_MODE_A	UART_LCR_DLAB	/* Configutation mode A */
108 #define UART_LCR_CONF_MODE_B	0xBF		/* Configutation mode B */
109 
110 #define UART_MCR	4	/* Out: Modem Control Register */
111 #define UART_MCR_CLKSEL		0x80 /* Divide clock by 4 (TI16C752, EFR[4]=1) */
112 #define UART_MCR_TCRTLR		0x40 /* Access TCR/TLR (TI16C752, EFR[4]=1) */
113 #define UART_MCR_XONANY		0x20 /* Enable Xon Any (TI16C752, EFR[4]=1) */
114 #define UART_MCR_AFE		0x20 /* Enable auto-RTS/CTS (TI16C550C/TI16C750) */
115 #define UART_MCR_LOOP		0x10 /* Enable loopback test mode */
116 #define UART_MCR_OUT2		0x08 /* Out2 complement */
117 #define UART_MCR_OUT1		0x04 /* Out1 complement */
118 #define UART_MCR_RTS		0x02 /* RTS complement */
119 #define UART_MCR_DTR		0x01 /* DTR complement */
120 
121 #define UART_LSR	5	/* In:  Line Status Register */
122 #define UART_LSR_FIFOE		0x80 /* Fifo error */
123 #define UART_LSR_TEMT		0x40 /* Transmitter empty */
124 #define UART_LSR_THRE		0x20 /* Transmit-hold-register empty */
125 #define UART_LSR_BI		0x10 /* Break interrupt indicator */
126 #define UART_LSR_FE		0x08 /* Frame error indicator */
127 #define UART_LSR_PE		0x04 /* Parity error indicator */
128 #define UART_LSR_OE		0x02 /* Overrun error indicator */
129 #define UART_LSR_DR		0x01 /* Receiver data ready */
130 #define UART_LSR_BRK_ERROR_BITS	0x1E /* BI, FE, PE, OE bits */
131 
132 #define UART_MSR	6	/* In:  Modem Status Register */
133 #define UART_MSR_DCD		0x80 /* Data Carrier Detect */
134 #define UART_MSR_RI		0x40 /* Ring Indicator */
135 #define UART_MSR_DSR		0x20 /* Data Set Ready */
136 #define UART_MSR_CTS		0x10 /* Clear to Send */
137 #define UART_MSR_DDCD		0x08 /* Delta DCD */
138 #define UART_MSR_TERI		0x04 /* Trailing edge ring indicator */
139 #define UART_MSR_DDSR		0x02 /* Delta DSR */
140 #define UART_MSR_DCTS		0x01 /* Delta CTS */
141 #define UART_MSR_ANY_DELTA	0x0F /* Any of the delta bits! */
142 
143 #define UART_SCR	7	/* I/O: Scratch Register */
144 
145 /*
146  * DLAB=1
147  */
148 #define UART_DLL	0	/* Out: Divisor Latch Low */
149 #define UART_DLM	1	/* Out: Divisor Latch High */
150 
151 /*
152  * LCR=0xBF (or DLAB=1 for 16C660)
153  */
154 #define UART_EFR	2	/* I/O: Extended Features Register */
155 #define UART_XR_EFR	9	/* I/O: Extended Features Register (XR17D15x) */
156 #define UART_EFR_CTS		0x80 /* CTS flow control */
157 #define UART_EFR_RTS		0x40 /* RTS flow control */
158 #define UART_EFR_SCD		0x20 /* Special character detect */
159 #define UART_EFR_ECB		0x10 /* Enhanced control bit */
160 /*
161  * the low four bits control software flow control
162  */
163 
164 /*
165  * LCR=0xBF, TI16C752, ST16650, ST16650A, ST16654
166  */
167 #define UART_XON1	4	/* I/O: Xon character 1 */
168 #define UART_XON2	5	/* I/O: Xon character 2 */
169 #define UART_XOFF1	6	/* I/O: Xoff character 1 */
170 #define UART_XOFF2	7	/* I/O: Xoff character 2 */
171 
172 /*
173  * EFR[4]=1 MCR[6]=1, TI16C752
174  */
175 #define UART_TI752_TCR	6	/* I/O: transmission control register */
176 #define UART_TI752_TLR	7	/* I/O: trigger level register */
177 
178 /*
179  * LCR=0xBF, XR16C85x
180  */
181 #define UART_TRG	0	/* FCTR bit 7 selects Rx or Tx
182 				 * In: Fifo count
183 				 * Out: Fifo custom trigger levels */
184 /*
185  * These are the definitions for the Programmable Trigger Register
186  */
187 #define UART_TRG_1		0x01
188 #define UART_TRG_4		0x04
189 #define UART_TRG_8		0x08
190 #define UART_TRG_16		0x10
191 #define UART_TRG_32		0x20
192 #define UART_TRG_64		0x40
193 #define UART_TRG_96		0x60
194 #define UART_TRG_120		0x78
195 #define UART_TRG_128		0x80
196 
197 #define UART_FCTR	1	/* Feature Control Register */
198 #define UART_FCTR_RTS_NODELAY	0x00  /* RTS flow control delay */
199 #define UART_FCTR_RTS_4DELAY	0x01
200 #define UART_FCTR_RTS_6DELAY	0x02
201 #define UART_FCTR_RTS_8DELAY	0x03
202 #define UART_FCTR_IRDA		0x04  /* IrDa data encode select */
203 #define UART_FCTR_TX_INT	0x08  /* Tx interrupt type select */
204 #define UART_FCTR_TRGA		0x00  /* Tx/Rx 550 trigger table select */
205 #define UART_FCTR_TRGB		0x10  /* Tx/Rx 650 trigger table select */
206 #define UART_FCTR_TRGC		0x20  /* Tx/Rx 654 trigger table select */
207 #define UART_FCTR_TRGD		0x30  /* Tx/Rx 850 programmable trigger select */
208 #define UART_FCTR_SCR_SWAP	0x40  /* Scratch pad register swap */
209 #define UART_FCTR_RX		0x00  /* Programmable trigger mode select */
210 #define UART_FCTR_TX		0x80  /* Programmable trigger mode select */
211 
212 /*
213  * LCR=0xBF, FCTR[6]=1
214  */
215 #define UART_EMSR	7	/* Extended Mode Select Register */
216 #define UART_EMSR_FIFO_COUNT	0x01  /* Rx/Tx select */
217 #define UART_EMSR_ALT_COUNT	0x02  /* Alternating count select */
218 
219 /*
220  * The Intel XScale on-chip UARTs define these bits
221  */
222 #define UART_IER_DMAE	0x80	/* DMA Requests Enable */
223 #define UART_IER_UUE	0x40	/* UART Unit Enable */
224 #define UART_IER_NRZE	0x20	/* NRZ coding Enable */
225 #define UART_IER_RTOIE	0x10	/* Receiver Time Out Interrupt Enable */
226 
227 #define UART_IIR_TOD	0x08	/* Character Timeout Indication Detected */
228 
229 #define UART_FCR_PXAR1	0x00	/* receive FIFO threshold = 1 */
230 #define UART_FCR_PXAR8	0x40	/* receive FIFO threshold = 8 */
231 #define UART_FCR_PXAR16	0x80	/* receive FIFO threshold = 16 */
232 #define UART_FCR_PXAR32	0xc0	/* receive FIFO threshold = 32 */
233 
234 /*
235  * Intel MID on-chip HSU (High Speed UART) defined bits
236  */
237 #define UART_FCR_HSU_64_1B	0x00	/* receive FIFO treshold = 1 */
238 #define UART_FCR_HSU_64_16B	0x40	/* receive FIFO treshold = 16 */
239 #define UART_FCR_HSU_64_32B	0x80	/* receive FIFO treshold = 32 */
240 #define UART_FCR_HSU_64_56B	0xc0	/* receive FIFO treshold = 56 */
241 
242 #define UART_FCR_HSU_16_1B	0x00	/* receive FIFO treshold = 1 */
243 #define UART_FCR_HSU_16_4B	0x40	/* receive FIFO treshold = 4 */
244 #define UART_FCR_HSU_16_8B	0x80	/* receive FIFO treshold = 8 */
245 #define UART_FCR_HSU_16_14B	0xc0	/* receive FIFO treshold = 14 */
246 
247 #define UART_FCR_HSU_64B_FIFO	0x20	/* chose 64 bytes FIFO */
248 #define UART_FCR_HSU_16B_FIFO	0x00	/* chose 16 bytes FIFO */
249 
250 #define UART_FCR_HALF_EMPT_TXI	0x00	/* trigger TX_EMPT IRQ for half empty */
251 #define UART_FCR_FULL_EMPT_TXI	0x08	/* trigger TX_EMPT IRQ for full empty */
252 
253 /*
254  * These register definitions are for the 16C950
255  */
256 #define UART_ASR	0x01	/* Additional Status Register */
257 #define UART_RFL	0x03	/* Receiver FIFO level */
258 #define UART_TFL 	0x04	/* Transmitter FIFO level */
259 #define UART_ICR	0x05	/* Index Control Register */
260 
261 /* The 16950 ICR registers */
262 #define UART_ACR	0x00	/* Additional Control Register */
263 #define UART_CPR	0x01	/* Clock Prescalar Register */
264 #define UART_TCR	0x02	/* Times Clock Register */
265 #define UART_CKS	0x03	/* Clock Select Register */
266 #define UART_TTL	0x04	/* Transmitter Interrupt Trigger Level */
267 #define UART_RTL	0x05	/* Receiver Interrupt Trigger Level */
268 #define UART_FCL	0x06	/* Flow Control Level Lower */
269 #define UART_FCH	0x07	/* Flow Control Level Higher */
270 #define UART_ID1	0x08	/* ID #1 */
271 #define UART_ID2	0x09	/* ID #2 */
272 #define UART_ID3	0x0A	/* ID #3 */
273 #define UART_REV	0x0B	/* Revision */
274 #define UART_CSR	0x0C	/* Channel Software Reset */
275 #define UART_NMR	0x0D	/* Nine-bit Mode Register */
276 #define UART_CTR	0xFF
277 
278 /*
279  * The 16C950 Additional Control Register
280  */
281 #define UART_ACR_RXDIS	0x01	/* Receiver disable */
282 #define UART_ACR_TXDIS	0x02	/* Transmitter disable */
283 #define UART_ACR_DSRFC	0x04	/* DSR Flow Control */
284 #define UART_ACR_TLENB	0x20	/* 950 trigger levels enable */
285 #define UART_ACR_ICRRD	0x40	/* ICR Read enable */
286 #define UART_ACR_ASREN	0x80	/* Additional status enable */
287 
288 
289 
290 /*
291  * These definitions are for the RSA-DV II/S card, from
292  *
293  * Kiyokazu SUTO <suto@ks-and-ks.ne.jp>
294  */
295 
296 #define UART_RSA_BASE (-8)
297 
298 #define UART_RSA_MSR ((UART_RSA_BASE) + 0) /* I/O: Mode Select Register */
299 
300 #define UART_RSA_MSR_SWAP (1 << 0) /* Swap low/high 8 bytes in I/O port addr */
301 #define UART_RSA_MSR_FIFO (1 << 2) /* Enable the external FIFO */
302 #define UART_RSA_MSR_FLOW (1 << 3) /* Enable the auto RTS/CTS flow control */
303 #define UART_RSA_MSR_ITYP (1 << 4) /* Level (1) / Edge triger (0) */
304 
305 #define UART_RSA_IER ((UART_RSA_BASE) + 1) /* I/O: Interrupt Enable Register */
306 
307 #define UART_RSA_IER_Rx_FIFO_H (1 << 0) /* Enable Rx FIFO half full int. */
308 #define UART_RSA_IER_Tx_FIFO_H (1 << 1) /* Enable Tx FIFO half full int. */
309 #define UART_RSA_IER_Tx_FIFO_E (1 << 2) /* Enable Tx FIFO empty int. */
310 #define UART_RSA_IER_Rx_TOUT (1 << 3) /* Enable char receive timeout int */
311 #define UART_RSA_IER_TIMER (1 << 4) /* Enable timer interrupt */
312 
313 #define UART_RSA_SRR ((UART_RSA_BASE) + 2) /* IN: Status Read Register */
314 
315 #define UART_RSA_SRR_Tx_FIFO_NEMP (1 << 0) /* Tx FIFO is not empty (1) */
316 #define UART_RSA_SRR_Tx_FIFO_NHFL (1 << 1) /* Tx FIFO is not half full (1) */
317 #define UART_RSA_SRR_Tx_FIFO_NFUL (1 << 2) /* Tx FIFO is not full (1) */
318 #define UART_RSA_SRR_Rx_FIFO_NEMP (1 << 3) /* Rx FIFO is not empty (1) */
319 #define UART_RSA_SRR_Rx_FIFO_NHFL (1 << 4) /* Rx FIFO is not half full (1) */
320 #define UART_RSA_SRR_Rx_FIFO_NFUL (1 << 5) /* Rx FIFO is not full (1) */
321 #define UART_RSA_SRR_Rx_TOUT (1 << 6) /* Character reception timeout occurred (1) */
322 #define UART_RSA_SRR_TIMER (1 << 7) /* Timer interrupt occurred */
323 
324 #define UART_RSA_FRR ((UART_RSA_BASE) + 2) /* OUT: FIFO Reset Register */
325 
326 #define UART_RSA_TIVSR ((UART_RSA_BASE) + 3) /* I/O: Timer Interval Value Set Register */
327 
328 #define UART_RSA_TCR ((UART_RSA_BASE) + 4) /* OUT: Timer Control Register */
329 
330 #define UART_RSA_TCR_SWITCH (1 << 0) /* Timer on */
331 
332 /*
333  * The RSA DSV/II board has two fixed clock frequencies.  One is the
334  * standard rate, and the other is 8 times faster.
335  */
336 #define SERIAL_RSA_BAUD_BASE (921600)
337 #define SERIAL_RSA_BAUD_BASE_LO (SERIAL_RSA_BAUD_BASE / 8)
338 
339 /*
340  * Extra serial register definitions for the internal UARTs
341  * in TI OMAP processors.
342  */
343 #define UART_OMAP_MDR1		0x08	/* Mode definition register */
344 #define UART_OMAP_MDR2		0x09	/* Mode definition register 2 */
345 #define UART_OMAP_SCR		0x10	/* Supplementary control register */
346 #define UART_OMAP_SSR		0x11	/* Supplementary status register */
347 #define UART_OMAP_EBLR		0x12	/* BOF length register */
348 #define UART_OMAP_OSC_12M_SEL	0x13	/* OMAP1510 12MHz osc select */
349 #define UART_OMAP_MVER		0x14	/* Module version register */
350 #define UART_OMAP_SYSC		0x15	/* System configuration register */
351 #define UART_OMAP_SYSS		0x16	/* System status register */
352 #define UART_OMAP_WER		0x17	/* Wake-up enable register */
353 
354 /*
355  * These are the definitions for the MDR1 register
356  */
357 #define UART_OMAP_MDR1_16X_MODE		0x00	/* UART 16x mode */
358 #define UART_OMAP_MDR1_SIR_MODE		0x01	/* SIR mode */
359 #define UART_OMAP_MDR1_16X_ABAUD_MODE	0x02	/* UART 16x auto-baud */
360 #define UART_OMAP_MDR1_13X_MODE		0x03	/* UART 13x mode */
361 #define UART_OMAP_MDR1_MIR_MODE		0x04	/* MIR mode */
362 #define UART_OMAP_MDR1_FIR_MODE		0x05	/* FIR mode */
363 #define UART_OMAP_MDR1_CIR_MODE		0x06	/* CIR mode */
364 #define UART_OMAP_MDR1_DISABLE		0x07	/* Disable (default state) */
365 
366 #endif /* _LINUX_SERIAL_REG_H */
367 
368