Home
last modified time | relevance | path

Searched refs:MHz (Results 1 – 25 of 106) sorted by relevance

12345

/linux-2.6.39/Documentation/fb/
Dviafb.modes10 # 640x480, 60 Hz, Non-Interlaced (25.175 MHz dotclock)
29 # D: 25.175 MHz, H: 31.469 kHz, V: 59.94 Hz
32 # D: 24.823 MHz, H: 39.780 kHz, V: 60.00 Hz
35 # 640x480, 75 Hz, Non-Interlaced (31.50 MHz dotclock)
53 # D: 31.50 MHz, H: 37.500 kHz, V: 75.00 Hz
56 # 640x480, 85 Hz, Non-Interlaced (36.000 MHz dotclock)
74 # D: 36.000 MHz, H: 43.269 kHz, V: 85.00 Hz
77 # 640x480, 100 Hz, Non-Interlaced (43.163 MHz dotclock)
95 # D: 43.163 MHz, H: 50.900 kHz, V: 100.00 Hz
98 # 640x480, 120 Hz, Non-Interlaced (52.406 MHz dotclock)
[all …]
Ds3fb.txt39 lower pixclocks (maximum usually between 50-60 MHz, depending on specific
40 hardware, i get best results from plain S3 Trio32 card - about 75 MHz). This
/linux-2.6.39/arch/arm/mach-omap1/
DKconfig183 bool "OMAP ARM 216 MHz CPU (1710 only)"
186 Enable 216 MHz clock for OMAP1710 CPU. If unsure, say N.
189 bool "OMAP ARM 195 MHz CPU"
192 Enable 195MHz clock for OMAP CPU. If unsure, say N.
195 bool "OMAP ARM 192 MHz CPU"
198 Enable 192MHz clock for OMAP CPU. If unsure, say N.
201 bool "OMAP ARM 182 MHz CPU"
204 Enable 182MHz clock for OMAP CPU. If unsure, say N.
207 bool "OMAP ARM 168 MHz CPU"
210 Enable 168MHz clock for OMAP CPU. If unsure, say N.
[all …]
/linux-2.6.39/Documentation/frv/
Dclock.txt42 Clock-In: 50.00 MHz
43 Clock-Core: 300.00 MHz
44 Clock-SDRAM: 100.00 MHz
45 Clock-CBus: 100.00 MHz
46 Clock-Res: 50.00 MHz
47 Clock-Ext: 50.00 MHz
48 Clock-DSU: 25.00 MHz
/linux-2.6.39/arch/mips/jazz/
DKconfig7 This is a machine with a R4400 133/150 MHz CPU. To compile a Linux
19 This is a machine with a R4000 100 MHz CPU. To compile a Linux
30 This is a machine with a R4000 100 MHz CPU. To compile a Linux
/linux-2.6.39/arch/powerpc/boot/dts/
Dmedia5200.dts31 timebase-frequency = <33000000>; // 33 MHz, these were configured by U-Boot
32 bus-frequency = <132000000>; // 132 MHz
33 clock-frequency = <396000000>; // 396 MHz
42 bus-frequency = <132000000>;// 132 MHz
Dgamecube.dts39 clock-frequency = <486000000>; /* 486MHz */
40 bus-frequency = <162000000>; /* 162MHz core-to-bus 3x */
41 timebase-frequency = <40500000>; /* 162MHz / 4 */
Dwii.dts48 clock-frequency = <729000000>; /* 729MHz */
49 bus-frequency = <243000000>; /* 243MHz core-to-bus 3x */
50 timebase-frequency = <60750000>; /* 243MHz / 4 */
Dc2k.dts37 clock-frequency = <996000000>; /* 996 MHz */
38 bus-frequency = <166666667>; /* 166.6666 MHz */
39 timebase-frequency = <41666667>; /* 166.6666/4 MHz */
57 clock-frequency = <166666667>; /* 166.66... MHz */
Dpdm360ng.dts40 timebase-frequency = <49500000>;// 49.5 MHz (csb/4)
41 bus-frequency = <198000000>; // 198 MHz csb bus
42 clock-frequency = <396000000>; // 396 MHz ppc core
138 bus-frequency = <66000000>; // 66 MHz ips bus
/linux-2.6.39/drivers/staging/tty/
Dspecialix_io8.h65 #define MHz *1000000 /* I'm ashamed of myself. */ macro
68 #define SX_OSCFREQ (25 MHz/2)
/linux-2.6.39/arch/powerpc/boot/
Dprpmc2800.c27 #define MHz (1000U*1000U) macro
28 #define GHz (1000U*MHz)
99 .core_speed = 733*MHz,
138 .core_speed = 733*MHz,
203 .core_speed = 733*MHz,
242 .core_speed = 733*MHz,
268 .core_speed = 733*MHz,
/linux-2.6.39/Documentation/scsi/
Daic7xxx.txt21 aic7770 10 EISA/VL 10MHz 16Bit 4 1
22 aic7850 10 PCI/32 10MHz 8Bit 3
23 aic7855 10 PCI/32 10MHz 8Bit 3
24 aic7856 10 PCI/32 10MHz 8Bit 3
25 aic7859 10 PCI/32 20MHz 8Bit 3
26 aic7860 10 PCI/32 20MHz 8Bit 3
27 aic7870 10 PCI/32 10MHz 16Bit 16
28 aic7880 10 PCI/32 20MHz 16Bit 16
29 aic7890 20 PCI/32 40MHz 16Bit 16 3 4 5 6 7 8
30 aic7891 20 PCI/64 40MHz 16Bit 16 3 4 5 6 7 8
[all …]
Daic79xx.txt24 AIC-7901A Single Channel 64-bit PCI-X 133MHz to
26 AIC-7901B Single Channel 64-bit PCI-X 133MHz to
28 AIC-7902A4 Dual Channel 64-bit PCI-X 133MHz to
30 AIC-7902B Dual Channel 64-bit PCI-X 133MHz to
35 Adaptec SCSI Card 39320 Dual Channel 64-bit PCI-X 133MHz to 7902A4/7902B
38 Adaptec SCSI Card 39320A Dual Channel 64-bit PCI-X 133MHz to 7902B
41 Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
44 Adaptec SCSI Card 39320D Dual Channel 64-bit PCI-X 133MHz to 7902A4
48 Adaptec SCSI Card 29320 Single Channel 64-bit PCI-X 133MHz to 7901A
52 Adaptec SCSI Card 29320A Single Channel 64-bit PCI-X 133MHz to 7901B
[all …]
/linux-2.6.39/Documentation/cpu-freq/
Dcpufreq-nforce2.txt13 min_fsb defaults to FSB at boot time - 50 MHz.
17 booting with 200 MHz, 150 should always work.
Dpcc-cpufreq.txt133 pcc-cpufreq: (v1.00.00) driver loaded with frequency limits: 1600 MHz, 2933
134 MHz
137 between the limits (1600 MHz, and 2933 MHz) specified in the message.
184 In this example, the nominal frequency is 2933 MHz. The driver obtains the
187 54% of 2933 MHz = 1583 MHz
/linux-2.6.39/arch/arm/mach-pxa/
Dsleep.S87 @ with core operating above 91 MHz
129 @ about suspending with PXBus operating above 133MHz
149 orrne r7, r7, #1 @@ 99.53MHz
176 @ need 6 13-MHz cycles before changing PWRMODE
177 @ just set frequency to 91-MHz... 6*91/13 = 42
/linux-2.6.39/drivers/staging/gma500/
Dpsb_bl.c34 #define MHz 1000000 macro
109 value = (core_clock * MHz) / BLC_PWM_FREQ_CALC_CONSTANT; in device_backlight_init()
/linux-2.6.39/Documentation/dvb/
Davermedia.txt168 ABC VHF 12 226.5 MHz
169 TEN VHF 11 219.5 MHz
170 NINE VHF 8 191.625 MHz
171 SEVEN VHF 6 177.5 MHz
172 SBS UHF 29 536.5 MHz
184 T 226500000 7MHz 2/3 NONE QAM64 8k 1/8 NONE
185 T 191625000 7MHz 2/3 NONE QAM64 8k 1/8 NONE
186 T 219500000 7MHz 2/3 NONE QAM64 8k 1/8 NONE
187 T 177500000 7MHz 2/3 NONE QAM64 8k 1/8 NONE
188 T 536500000 7MHz 2/3 NONE QAM64 8k 1/8 NONE
/linux-2.6.39/arch/arm/mach-s3c2440/
DKconfig49 Indicate that the build needs to support 12MHz system
55 Indicate that the build needs to support 16.9344MHz system
63 PLL tables for S3C2440 or S3C2442 CPUs with 12MHz crystals.
70 PLL tables for S3C2440 or S3C2442 CPUs with 16.934MHz crystals.
/linux-2.6.39/drivers/ata/
Dpata_hpt37x.c823 static const int MHz[4] = { 33, 40, 50, 66 }; in hpt37x_init_one() local
988 f_low = (MHz[clock_slot] * 48) / MHz[dpll]; in hpt37x_init_one()
1022 MHz[clock_slot], MHz[dpll]); in hpt37x_init_one()
1037 chip_table->name, MHz[clock_slot]); in hpt37x_init_one()
/linux-2.6.39/Documentation/spi/
Dep93xx_spi70 * We use 10 MHz even though the maximum is 7.4 MHz. The driver
/linux-2.6.39/Documentation/video4linux/
DREADME.saa713456 - 32.11 MHz -> .audio_clock=0x187de7
57 - 24.576MHz -> .audio_clock=0x200000
/linux-2.6.39/drivers/video/
Dimsttfb.c438 setclkMHz(struct imstt_par *par, __u32 MHz) in setclkMHz() argument
454 if (x == MHz) in setclkMHz()
456 if (x > MHz) { in setclkMHz()
459 } else if (spilled && x < MHz) { in setclkMHz()
473 __u32 MHz, hes, heb, veb, htp, vtp; in compute_imstt_regvals_ibm() local
478 MHz = 30 /* .25 */ ; in compute_imstt_regvals_ibm()
482 MHz = 57 /* .27_ */ ; in compute_imstt_regvals_ibm()
486 MHz = 80; in compute_imstt_regvals_ibm()
490 MHz = 101 /* .6_ */ ; in compute_imstt_regvals_ibm()
494 MHz = yres == 960 ? 126 : 135; in compute_imstt_regvals_ibm()
[all …]
/linux-2.6.39/Documentation/i2c/busses/
Di2c-ali15x345 100MHz CPU Front Side bus
46 * "Aladdin V" includes the M1541 Socket 7 North bridge with AGP and 100MHz
60 with host bus up to 83.3 MHz.

12345